| # |
| # FDDI network device configuration |
| # |
| |
| config FDDI |
| tristate "FDDI driver support" |
| depends on PCI || EISA || TC |
| ---help--- |
| Fiber Distributed Data Interface is a high speed local area network |
| design; essentially a replacement for high speed Ethernet. FDDI can |
| run over copper or fiber. If you are connected to such a network and |
| want a driver for the FDDI card in your computer, say Y here (and |
| then also Y to the driver for your FDDI card, below). Most people |
| will say N. |
| |
| if FDDI |
| |
| config DEFZA |
| tristate "DEC FDDIcontroller 700/700-C (DEFZA-xx) support" |
| depends on FDDI && TC |
| help |
| This is support for the DEC FDDIcontroller 700 (DEFZA-AA, fiber) |
| and 700-C (DEFZA-CA, copper) TURBOchannel network cards which |
| can connect you to a local FDDI network. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called defza. If unsure, say N. |
| |
| config DEFXX |
| tristate "Digital DEFTA/DEFEA/DEFPA adapter support" |
| depends on FDDI && (PCI || EISA || TC) |
| ---help--- |
| This is support for the DIGITAL series of TURBOchannel (DEFTA), |
| EISA (DEFEA) and PCI (DEFPA) controllers which can connect you |
| to a local FDDI network. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called defxx. If unsure, say N. |
| |
| config DEFXX_MMIO |
| bool |
| prompt "Use MMIO instead of PIO" if PCI || EISA |
| depends on DEFXX |
| default n if PCI || EISA |
| default y |
| ---help--- |
| This instructs the driver to use EISA or PCI memory-mapped I/O |
| (MMIO) as appropriate instead of programmed I/O ports (PIO). |
| Enabling this gives an improvement in processing time in parts |
| of the driver, but it may cause problems with EISA (DEFEA) |
| adapters. TURBOchannel does not have the concept of I/O ports, |
| so MMIO is always used for these (DEFTA) adapters. |
| |
| If unsure, say N. |
| |
| config SKFP |
| tristate "SysKonnect FDDI PCI support" |
| depends on FDDI && PCI |
| select BITREVERSE |
| ---help--- |
| Say Y here if you have a SysKonnect FDDI PCI adapter. |
| The following adapters are supported by this driver: |
| - SK-5521 (SK-NET FDDI-UP) |
| - SK-5522 (SK-NET FDDI-UP DAS) |
| - SK-5541 (SK-NET FDDI-FP) |
| - SK-5543 (SK-NET FDDI-LP) |
| - SK-5544 (SK-NET FDDI-LP DAS) |
| - SK-5821 (SK-NET FDDI-UP64) |
| - SK-5822 (SK-NET FDDI-UP64 DAS) |
| - SK-5841 (SK-NET FDDI-FP64) |
| - SK-5843 (SK-NET FDDI-LP64) |
| - SK-5844 (SK-NET FDDI-LP64 DAS) |
| - Netelligent 100 FDDI DAS Fibre SC |
| - Netelligent 100 FDDI SAS Fibre SC |
| - Netelligent 100 FDDI DAS UTP |
| - Netelligent 100 FDDI SAS UTP |
| - Netelligent 100 FDDI SAS Fibre MIC |
| |
| Read <file:Documentation/networking/skfp.txt> for information about |
| the driver. |
| |
| Questions concerning this driver can be addressed to: |
| <linux@syskonnect.de> |
| |
| To compile this driver as a module, choose M here: the module |
| will be called skfp. This is recommended. |
| |
| endif # FDDI |
