blob: 1f02034c7e99a848713a23ea612be0d7736411d3 [file] [log] [blame] [edit]
/*
* a4m072 board Device Tree Source
*
* Copyright (C) 2011 DENX Software Engineering GmbH
* Heiko Schocher <hs@denx.de>
*
* Copyright (C) 2007 Semihalf
* Marian Balakowicz <m8@semihalf.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
/include/ "mpc5200b.dtsi"
&gpt0 { fsl,has-wdt; };
&gpt3 { gpio-controller; };
&gpt4 { gpio-controller; };
&gpt5 { gpio-controller; };
/ {
model = "anonymous,a4m072";
compatible = "anonymous,a4m072";
soc5200@f0000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc5200b-immr";
ranges = <0 0xf0000000 0x0000c000>;
reg = <0xf0000000 0x00000100>;
bus-frequency = <0>; /* From boot loader */
system-frequency = <0>; /* From boot loader */
cdm@200 {
fsl,init-ext-48mhz-en = <0x0>;
fsl,init-fd-enable = <0x01>;
fsl,init-fd-counters = <0x3333>;
};
spi@f00 {
status = "disabled";
};
psc@2000 {
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
reg = <0x2000 0x100>;
interrupts = <2 1 0>;
};
psc@2200 {
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
reg = <0x2200 0x100>;
interrupts = <2 2 0>;
};
psc@2400 {
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
reg = <0x2400 0x100>;
interrupts = <2 3 0>;
};
psc@2600 {
status = "disabled";
};
psc@2800 {
status = "disabled";
};
psc@2c00 {
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
reg = <0x2c00 0x100>;
interrupts = <2 4 0>;
};
ethernet@3000 {
phy-handle = <&phy0>;
};
mdio@3000 {
phy0: ethernet-phy@1f {
reg = <0x1f>;
interrupts = <1 2 0>; /* IRQ 2 active low */
};
};
i2c@3d00 {
status = "disabled";
};
i2c@3d40 {
hwmon@2e {
compatible = "nsc,lm87";
reg = <0x2e>;
};
rtc@51 {
compatible = "nxp,rtc8564";
reg = <0x51>;
};
};
};
localbus {
compatible = "fsl,mpc5200b-lpb","simple-bus";
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0xfe000000 0x02000000
1 0 0x62000000 0x00400000
2 0 0x64000000 0x00200000
3 0 0x66000000 0x01000000
6 0 0x68000000 0x01000000
7 0 0x6a000000 0x00000004>;
flash@0,0 {
compatible = "cfi-flash";
reg = <0 0 0x02000000>;
bank-width = <2>;
#size-cells = <1>;
#address-cells = <1>;
};
sram0@1,0 {
compatible = "mtd-ram";
reg = <1 0x00000 0x00400000>;
bank-width = <2>;
};
};
pci@f0000d00 {
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
compatible = "fsl,mpc5200-pci";
reg = <0xf0000d00 0x100>;
interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map = <
/* IDSEL 0x16 */
0xc000 0 0 1 &mpc5200_pic 1 3 3
0xc000 0 0 2 &mpc5200_pic 1 3 3
0xc000 0 0 3 &mpc5200_pic 1 3 3
0xc000 0 0 4 &mpc5200_pic 1 3 3>;
clock-frequency = <0>; /* From boot loader */
interrupts = <2 8 0 2 9 0 2 10 0>;
bus-range = <0 0>;
ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000
0x02000000 0 0x90000000 0x90000000 0 0x10000000
0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
};
};