blob: cb41ccdaccfdd8df5ec87ba07a0713748098d8ad [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Google Quackingstick board device tree source
*
* Copyright 2021 Google LLC.
*/
/dts-v1/;
#include "sc7180-trogdor.dtsi"
/* This board only has 1 USB Type-C port. */
/delete-node/ &usb_c1;
/ {
ppvar_lcd: ppvar-lcd-regulator {
compatible = "regulator-fixed";
regulator-name = "ppvar_lcd";
gpio = <&tlmm 88 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&ppvar_lcd_en>;
vin-supply = <&pp5000_a>;
};
v1p8_disp: v1p8-disp-regulator {
compatible = "regulator-fixed";
regulator-name = "v1p8_disp";
gpio = <&tlmm 86 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&pp1800_disp_on>;
vin-supply = <&pp3300_a>;
};
};
&backlight {
pwms = <&cros_ec_pwm 0>;
};
&camcc {
status = "okay";
};
&cros_ec {
keyboard-controller {
compatible = "google,cros-ec-keyb-switches";
};
};
&dsi0 {
panel: panel@0 {
/* Compatible will be filled in per-board */
reg = <0>;
enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&lcd_rst>;
avdd-supply = <&ppvar_lcd>;
pp1800-supply = <&v1p8_disp>;
pp3300-supply = <&pp3300_dx_edp>;
backlight = <&backlight>;
rotation = <270>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
panel_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
};
};
ports {
port@1 {
endpoint {
remote-endpoint = <&panel_in>;
data-lanes = <0 1 2 3>;
};
};
};
};
&gpio_keys {
status = "okay";
};
&i2c4 {
status = "okay";
clock-frequency = <400000>;
ap_ts: touchscreen@10 {
compatible = "hid-over-i2c";
reg = <0x10>;
pinctrl-names = "default";
pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
interrupt-parent = <&tlmm>;
interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
post-power-on-delay-ms = <20>;
hid-descr-addr = <0x0001>;
vdd-supply = <&pp3300_ts>;
};
};
&sdhc_2 {
status = "okay";
};
&pp1800_uf_cam {
status = "okay";
};
&pp1800_wf_cam {
status = "okay";
};
&pp2800_uf_cam {
status = "okay";
};
&pp2800_wf_cam {
status = "okay";
};
/*
* No eDP on this board but it's logically the same signal so just give it
* a new name and assign the proper GPIO.
*/
pp3300_disp_on: &pp3300_dx_edp {
gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
};
/* PINCTRL - modifications to sc7180-trogdor.dtsi */
/*
* No eDP on this board but it's logically the same signal so just give it
* a new name and assign the proper GPIO.
*/
tp_en: &en_pp3300_dx_edp {
pins = "gpio67";
};
/* PINCTRL - board-specific pinctrl */
&tlmm {
gpio-line-names = "HUB_RST_L",
"AP_RAM_ID0",
"AP_SKU_ID2",
"AP_RAM_ID1",
"",
"AP_RAM_ID2",
"UF_CAM_EN",
"WF_CAM_EN",
"TS_RESET_L",
"TS_INT_L",
"",
"",
"AP_EDP_BKLTEN",
"UF_CAM_MCLK",
"WF_CAM_CLK",
"EDP_BRIJ_I2C_SDA",
"EDP_BRIJ_I2C_SCL",
"UF_CAM_SDA",
"UF_CAM_SCL",
"WF_CAM_SDA",
"WF_CAM_SCL",
"",
"",
"AMP_EN",
"P_SENSOR_INT_L",
"AP_SAR_SENSOR_SDA",
"AP_SAR_SENSOR_SCL",
"",
"HP_IRQ",
"WF_CAM_RST_L",
"UF_CAM_RST_L",
"AP_BRD_ID2",
"",
"AP_BRD_ID0",
"AP_H1_SPI_MISO",
"AP_H1_SPI_MOSI",
"AP_H1_SPI_CLK",
"AP_H1_SPI_CS_L",
"",
"",
"",
"",
"H1_AP_INT_ODL",
"",
"UART_AP_TX_DBG_RX",
"UART_DBG_TX_AP_RX",
"HP_I2C_SDA",
"HP_I2C_SCL",
"FORCED_USB_BOOT",
"",
"",
"AMP_DIN",
"PEN_DET_ODL",
"HP_BCLK",
"HP_LRCLK",
"HP_DOUT",
"HP_DIN",
"HP_MCLK",
"AP_SKU_ID0",
"AP_EC_SPI_MISO",
"AP_EC_SPI_MOSI",
"AP_EC_SPI_CLK",
"AP_EC_SPI_CS_L",
"AP_SPI_CLK",
"AP_SPI_MOSI",
"AP_SPI_MISO",
/*
* AP_FLASH_WP_L is crossystem ABI. Schematics
* call it BIOS_FLASH_WP_L.
*/
"AP_FLASH_WP_L",
"EN_PP3300_DX_EDP",
"AP_SPI_CS0_L",
"SD_CD_ODL",
"",
"",
"",
"",
"",
"UIM2_DATA",
"UIM2_CLK",
"UIM2_RST",
"UIM2_PRESENT_L",
"UIM1_DATA",
"UIM1_CLK",
"UIM1_RST",
"",
"CODEC_PWR_EN",
"HUB_EN",
"",
"PP1800_DISP_ON",
"LCD_RST",
"PPVAR_LCD_EN",
"",
"AP_SKU_ID1",
"AP_RST_REQ",
"",
"AP_BRD_ID1",
"AP_EC_INT_L",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"AP_TS_I2C_SDA",
"AP_TS_I2C_SCL",
"DP_HOT_PLUG_DET",
"EC_IN_RW_ODL";
lcd_rst: lcd-rst-state {
pins = "gpio87";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
ppvar_lcd_en: ppvar-lcd-en-state {
pins = "gpio88";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
pp1800_disp_on: pp1800-disp-on-state {
pins = "gpio86";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
};