blob: 3f79923376fb28f13a20992e88364587fcae2d95 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Device tree for the uDPU board.
* Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
* Copyright (C) 2016 Marvell
* Copyright (C) 2019 Methode Electronics
* Copyright (C) 2019 Telus
*
* Vladimir Vid <vladimir.vid@sartura.hr>
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "armada-372x.dtsi"
/ {
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
};
leds {
compatible = "gpio-leds";
led-power1 {
label = "udpu:green:power";
gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
};
led-power2 {
label = "udpu:red:power";
gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
};
led-network1 {
label = "udpu:green:network";
gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
};
led-network2 {
label = "udpu:red:network";
gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
};
led-alarm1 {
label = "udpu:green:alarm";
gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
};
led-alarm2 {
label = "udpu:red:alarm";
gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
};
};
sfp_eth1: sfp-eth1 {
compatible = "sff,sfp";
i2c-bus = <&i2c1>;
los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
};
};
&sdhci0 {
status = "okay";
bus-width = <8>;
mmc-ddr-1_8v;
mmc-hs400-1_8v;
marvell,pad-type = "fixed-1-8v";
non-removable;
no-sd;
no-sdio;
};
&spi0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&spi_quad_pins>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <54000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "firmware";
reg = <0x0 0x180000>;
};
partition@180000 {
label = "u-boot-env";
reg = <0x180000 0x10000>;
};
};
};
};
&pinctrl_nb {
i2c2_recovery_pins: i2c2-recovery-pins {
groups = "i2c2";
function = "gpio";
};
};
&i2c1 {
status = "okay";
pinctrl-names = "default", "recovery";
pinctrl-0 = <&i2c2_pins>;
pinctrl-1 = <&i2c2_recovery_pins>;
/delete-property/mrvl,i2c-fast-mode;
scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
temp-sensor@48 {
compatible = "ti,tmp75c";
reg = <0x48>;
};
temp-sensor@49 {
compatible = "ti,tmp75c";
reg = <0x49>;
};
};
&eth0 {
status = "okay";
managed = "in-band-status";
phys = <&comphy1 0>;
};
&eth1 {
phy-mode = "sgmii";
status = "okay";
managed = "in-band-status";
phys = <&comphy0 1>;
sfp = <&sfp_eth1>;
};
&usb3 {
status = "okay";
phys = <&usb2_utmi_otg_phy>;
phy-names = "usb2-utmi-otg-phy";
};
&uart0 {
status = "okay";
};