blob: 27a0d51289ddd4eeb9b9eaa14c1ebd565e30e38c [file] [log] [blame]
/*
* Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Beelink X2";
compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
aliases {
serial0 = &uart0;
ethernet0 = &emac;
ethernet1 = &sdiowifi;
};
cec-gpio {
compatible = "cec-gpio";
cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */
hdmi-phandle = <&hdmi>;
};
chosen {
stdout-path = "serial0:115200n8";
};
connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
led-0 {
label = "beelink-x2:blue:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
default-state = "on";
};
led-1 {
label = "beelink-x2:red:standby";
gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
};
};
gpio-keys {
compatible = "gpio-keys";
key-power {
label = "power";
linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
wakeup-source;
};
};
sound_spdif {
compatible = "simple-audio-card";
simple-audio-card,name = "On-board SPDIF";
simple-audio-card,cpu {
sound-dai = <&spdif>;
};
simple-audio-card,codec {
sound-dai = <&spdif_out>;
};
};
spdif_out: spdif-out {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "ext_clock";
};
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "mii";
allwinner,leds-active-low;
status = "okay";
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&ir {
linux,rc-map-name = "rc-tanix-tx3mini";
pinctrl-names = "default";
pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
/*
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
sdiowifi: sdio_wifi@1 {
reg = <1>;
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&reg_usb0_vbus {
gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
status = "okay";
};
&spdif {
pinctrl-names = "default";
pinctrl-0 = <&spdif_tx_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usbphy {
/* USB VBUS is always on except for the OTG port */
status = "okay";
usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
usb0_vbus-supply = <&reg_usb0_vbus>;
};