| // SPDX-License-Identifier: GPL-2.0 |
| #include "qcom-msm8974pro.dtsi" |
| #include "qcom-pm8841.dtsi" |
| #include "qcom-pm8941.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| model = "OnePlus One"; |
| compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974"; |
| chassis-type = "handset"; |
| qcom,msm-id = <194 0x10000>; |
| qcom,board-id = <8 0>; |
| |
| aliases { |
| serial0 = &blsp1_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| }; |
| |
| &blsp1_i2c1 { |
| status = "okay"; |
| |
| fuel-gauge@55 { |
| compatible = "ti,bq27541"; |
| reg = <0x55>; |
| power-supplies = <&bq24196_charger>; |
| }; |
| }; |
| |
| &blsp1_i2c2 { |
| status = "okay"; |
| |
| rmi4-i2c-dev@20 { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x20>; |
| |
| syna,startup-delay-ms = <100>; |
| |
| interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>; |
| vdd-supply = <&pm8941_l22>; |
| vio-supply = <&pm8941_lvs3>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touch_default_state>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| rmi4-f01@1 { |
| reg = <0x1>; |
| syna,nosleep-mode = <1>; |
| }; |
| |
| rmi4-f12@12 { |
| reg = <0x12>; |
| syna,sensor-type = <1>; |
| /* |
| * Touchscreen size is 2040x1080, y-values between |
| * 1920-2040 are used for touchkey (menu, home & back). |
| * For now clip it off so we don't get touch events |
| * outside of the display area. |
| */ |
| syna,clip-y-high = <1920>; |
| }; |
| }; |
| }; |
| |
| &blsp1_i2c6 { |
| status = "okay"; |
| |
| bq24196_charger: charger@6b { |
| compatible = "ti,bq24196"; |
| reg = <0x6b>; |
| interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>; |
| omit-battery-class; |
| }; |
| }; |
| |
| &blsp1_uart2 { |
| status = "okay"; |
| }; |
| |
| &gcc { |
| compatible = "qcom,gcc-msm8974pro-ac"; |
| }; |
| |
| &pm8941_coincell { |
| qcom,rset-ohms = <800>; |
| qcom,vset-millivolts = <3200>; |
| |
| status = "okay"; |
| }; |
| |
| &pronto { |
| vddmx-supply = <&pm8841_s1>; |
| vddcx-supply = <&pm8841_s2>; |
| vddpx-supply = <&pm8941_s3>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wcnss_pin_a>; |
| |
| status = "okay"; |
| |
| iris { |
| vddxo-supply = <&pm8941_l6>; |
| vddrfa-supply = <&pm8941_l11>; |
| vddpa-supply = <&pm8941_l19>; |
| vdddig-supply = <&pm8941_s3>; |
| }; |
| |
| smd-edge { |
| qcom,remote-pid = <4>; |
| label = "pronto"; |
| |
| wcnss { |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| &remoteproc_adsp { |
| cx-supply = <&pm8841_s2>; |
| |
| status = "okay"; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pm8841-regulators"; |
| |
| pm8841_s1: s1 { |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s2: s2 { |
| regulator-min-microvolt = <875000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-always-on; |
| }; |
| |
| pm8841_s3: s3 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,rpm-pm8941-regulators"; |
| |
| vdd_l1_l3-supply = <&pm8941_s1>; |
| vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; |
| vdd_l4_l11-supply = <&pm8941_s1>; |
| vdd_l5_l7-supply = <&pm8941_s2>; |
| vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; |
| vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>; |
| vdd_l9_l10_l17_l22-supply = <&vreg_boost>; |
| vdd_l13_l20_l23_l24-supply = <&vreg_boost>; |
| vdd_l21-supply = <&vreg_boost>; |
| |
| pm8941_s1: s1 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_s2: s2 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| |
| regulator-boot-on; |
| }; |
| |
| pm8941_s3: s3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-system-load = <154000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-allow-set-load; |
| }; |
| |
| pm8941_l1: l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l2: l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pm8941_l3: l3 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8941_l4: l4 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8941_l5: l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l6: l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-boot-on; |
| }; |
| |
| pm8941_l7: l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-boot-on; |
| }; |
| |
| pm8941_l8: l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l9: l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8941_l10: l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8941_l11: l11 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1350000>; |
| }; |
| |
| pm8941_l12: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-allow-set-load; |
| }; |
| |
| pm8941_l13: l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| }; |
| |
| pm8941_l14: l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l15: l15 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| pm8941_l16: l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| pm8941_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pm8941_l18: l18 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pm8941_l19: l19 { |
| regulator-min-microvolt = <2900000>; |
| regulator-max-microvolt = <3350000>; |
| }; |
| |
| pm8941_l20: l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l21: l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| }; |
| |
| pm8941_l22: l22 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-allow-set-load; |
| }; |
| |
| pm8941_l23: l23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| pm8941_l24: l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| |
| regulator-boot-on; |
| }; |
| |
| pm8941_lvs3: lvs3 {}; |
| }; |
| }; |
| |
| &sdhc_1 { |
| vmmc-supply = <&pm8941_l20>; |
| vqmmc-supply = <&pm8941_s3>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_on>; |
| pinctrl-1 = <&sdc1_off>; |
| |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| sdc1_on: sdc1-on-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| drive-strength = <4>; |
| bias-disable; |
| }; |
| |
| cmd-data-pins { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <4>; |
| bias-pull-up; |
| }; |
| }; |
| |
| touch_default_state: touch-default-state { |
| int-pins { |
| pins = "gpio61"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| input-enable; |
| }; |
| |
| reset-pins { |
| pins = "gpio60"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| wcnss_pin_a: wcnss-pin-active-state { |
| wlan-pins { |
| pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40"; |
| function = "wlan"; |
| drive-strength = <6>; |
| bias-pull-down; |
| }; |
| |
| bt-pins { |
| pins = "gpio35", "gpio43", "gpio44"; |
| function = "bt"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| }; |
| }; |
| |
| &usb { |
| phys = <&usb_hs1_phy>; |
| phy-select = <&tcsr 0xb000 0>; |
| extcon = <&smbb>, <&usb_id>; |
| vbus-supply = <&chg_otg>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| |
| status = "okay"; |
| }; |
| |
| &usb_hs1_phy { |
| status = "okay"; |
| |
| v1p8-supply = <&pm8941_l6>; |
| v3p3-supply = <&pm8941_l24>; |
| |
| extcon = <&smbb>; |
| qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| }; |
