| // SPDX-License-Identifier: GPL-2.0 |
| #include "qcom-msm8974pro.dtsi" |
| #include "qcom-pm8841.dtsi" |
| #include "qcom-pm8941.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| model = "Fairphone 2"; |
| compatible = "fairphone,fp2", "qcom,msm8974pro", "qcom,msm8974"; |
| chassis-type = "handset"; |
| |
| aliases { |
| mmc0 = &sdhc_1; |
| mmc1 = &sdhc_2; |
| serial0 = &blsp1_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_pin_a>; |
| |
| key-camera-snapshot { |
| label = "camera_snapshot"; |
| gpios = <&pm8941_gpios 1 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_CAMERA>; |
| wakeup-source; |
| debounce-interval = <15>; |
| }; |
| |
| key-volume-down { |
| label = "volume_down"; |
| gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| wakeup-source; |
| debounce-interval = <15>; |
| }; |
| |
| key-volume-up { |
| label = "volume_up"; |
| gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| wakeup-source; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| vibrator { |
| compatible = "gpio-vibrator"; |
| enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; |
| vcc-supply = <&pm8941_l18>; |
| }; |
| }; |
| |
| &blsp1_i2c2 { |
| status = "okay"; |
| |
| touchscreen@41 { |
| compatible = "ilitek,ili2120"; |
| reg = <0x41>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <28 IRQ_TYPE_EDGE_FALLING>; |
| reset-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>; |
| |
| touchscreen-size-x = <1080>; |
| touchscreen-size-y = <1920>; |
| }; |
| }; |
| |
| &blsp1_uart2 { |
| status = "okay"; |
| }; |
| |
| &imem { |
| reboot-mode { |
| mode-normal = <0x77665501>; |
| mode-bootloader = <0x77665500>; |
| mode-recovery = <0x77665502>; |
| }; |
| }; |
| |
| &pm8941_gpios { |
| gpio_keys_pin_a: gpio-keys-active-state { |
| pins = "gpio1", "gpio2", "gpio5"; |
| function = "normal"; |
| |
| bias-pull-up; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| }; |
| |
| &pm8941_lpg { |
| status = "okay"; |
| |
| qcom,power-source = <1>; |
| |
| multi-led { |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_STATUS; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@7 { |
| reg = <7>; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@6 { |
| reg = <6>; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@5 { |
| reg = <5>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| &pronto { |
| status = "okay"; |
| |
| vddmx-supply = <&pm8841_s1>; |
| vddcx-supply = <&pm8841_s2>; |
| vddpx-supply = <&pm8941_s3>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wcnss_pin_a>; |
| |
| iris { |
| vddxo-supply = <&pm8941_l6>; |
| vddrfa-supply = <&pm8941_l11>; |
| vddpa-supply = <&pm8941_l19>; |
| vdddig-supply = <&pm8941_s3>; |
| }; |
| |
| smd-edge { |
| qcom,remote-pid = <4>; |
| label = "pronto"; |
| |
| wcnss { |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| &remoteproc_adsp { |
| status = "okay"; |
| cx-supply = <&pm8841_s2>; |
| }; |
| |
| &remoteproc_mss { |
| status = "okay"; |
| cx-supply = <&pm8841_s2>; |
| mss-supply = <&pm8841_s3>; |
| mx-supply = <&pm8841_s1>; |
| pll-supply = <&pm8941_l12>; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pm8841-regulators"; |
| |
| pm8841_s1: s1 { |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s2: s2 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s3: s3 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,rpm-pm8941-regulators"; |
| |
| vdd_l1_l3-supply = <&pm8941_s1>; |
| vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; |
| vdd_l4_l11-supply = <&pm8941_s1>; |
| vdd_l5_l7-supply = <&pm8941_s2>; |
| vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; |
| vdd_l9_l10_l17_l22-supply = <&vreg_boost>; |
| vdd_l13_l20_l23_l24-supply = <&vreg_boost>; |
| vdd_l21-supply = <&vreg_boost>; |
| |
| pm8941_s1: s1 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_s2: s2 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_s3: s3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l1: l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l2: l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pm8941_l3: l3 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8941_l4: l4 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8941_l5: l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l6: l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l7: l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l8: l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l9: l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8941_l10: l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8941_l11: l11 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1350000>; |
| }; |
| |
| pm8941_l12: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l13: l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l14: l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l15: l15 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| pm8941_l16: l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| pm8941_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pm8941_l18: l18 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pm8941_l19: l19 { |
| regulator-min-microvolt = <2900000>; |
| regulator-max-microvolt = <3350000>; |
| }; |
| |
| pm8941_l20: l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l21: l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l22: l22 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| pm8941_l23: l23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| pm8941_l24: l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| regulator-boot-on; |
| }; |
| }; |
| }; |
| |
| &sdhc_1 { |
| status = "okay"; |
| |
| vmmc-supply = <&pm8941_l20>; |
| vqmmc-supply = <&pm8941_s3>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_on>; |
| pinctrl-1 = <&sdc1_off>; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| |
| vmmc-supply = <&pm8941_l21>; |
| vqmmc-supply = <&pm8941_l13>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_on>; |
| pinctrl-1 = <&sdc2_off>; |
| }; |
| |
| &smbb { |
| usb-charge-current-limit = <1500000>; |
| qcom,fast-charge-safe-current = <1500000>; |
| qcom,fast-charge-current-limit = <1500000>; |
| qcom,fast-charge-safe-voltage = <4380000>; |
| qcom,fast-charge-high-threshold-voltage = <4350000>; |
| qcom,auto-recharge-threshold-voltage = <4240000>; |
| qcom,minimum-input-voltage = <4450000>; |
| }; |
| |
| &tlmm { |
| sdc1_on: sdc1-on-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| cmd-data-pins { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdc2_on: sdc2-on-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| drive-strength = <10>; |
| bias-disable; |
| }; |
| |
| cmd-data-pins { |
| pins = "sdc2_cmd", "sdc2_data"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| }; |
| |
| wcnss_pin_a: wcnss-pin-active-state { |
| wlan-pins { |
| pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40"; |
| function = "wlan"; |
| |
| drive-strength = <6>; |
| bias-pull-down; |
| }; |
| |
| bt-pins { |
| pins = "gpio35", "gpio43", "gpio44"; |
| function = "bt"; |
| |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| fm-pins { |
| pins = "gpio41", "gpio42"; |
| function = "fm"; |
| |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| }; |
| }; |
| |
| &usb { |
| status = "okay"; |
| |
| phys = <&usb_hs1_phy>; |
| phy-select = <&tcsr 0xb000 0>; |
| extcon = <&smbb>, <&usb_id>; |
| vbus-supply = <&chg_otg>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| }; |
| |
| &usb_hs1_phy { |
| status = "okay"; |
| |
| v1p8-supply = <&pm8941_l6>; |
| v3p3-supply = <&pm8941_l24>; |
| |
| extcon = <&smbb>; |
| qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| }; |
