blob: f17e25ac98ddb083358e334105e2611db4451bd8 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-only
// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
/*
* TODO: add Orion USB device port init when kernel.org support is added.
* TODO: add flash write support: see below.
* TODO: add power-off support.
* TODO: add I2C EEPROM support.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "orion5x-mv88f5182.dtsi"
/ {
model = "LaCie Ethernet Disk mini V2";
compatible = "lacie,ethernet-disk-mini-v2", "marvell,orion5x-88f5182", "marvell,orion5x";
memory {
device_type = "memory";
reg = <0x00000000 0x4000000>; /* 64 MB */
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
stdout-path = &uart0;
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
<MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
<MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>;
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&pmx_power_button>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "Power-on Switch";
linux,code = <KEY_POWER>;
gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
};
};
gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&pmx_power_led>;
pinctrl-names = "default";
led@1 {
label = "power:blue";
gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
};
};
};
&devbus_bootcs {
status = "okay";
/* Read parameters */
devbus,bus-width = <8>;
devbus,turn-off-ps = <90000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <186000>;
devbus,acc-next-ps = <186000>;
/* Write parameters */
devbus,wr-high-ps = <90000>;
devbus,wr-low-ps = <90000>;
devbus,ale-wr-ps = <90000>;
/*
* Currently the MTD code does not recognize the MX29LV400CBCT
* as a bottom-type device. This could cause risks of
* accidentally erasing critical flash sectors. We thus define
* a single, write-protected partition covering the whole
* flash. TODO: once the flash part TOP/BOTTOM detection
* issue is sorted out in the MTD code, break this into at
* least three partitions: 'u-boot code', 'u-boot environment'
* and 'whatever is left'.
*/
flash@0 {
compatible = "cfi-flash";
reg = <0 0x80000>;
bank-width = <1>;
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "Full512Kb";
reg = <0 0x80000>;
read-only;
};
};
};
&ehci0 {
status = "okay";
};
&eth {
status = "okay";
ethernet-port@0 {
phy-handle = <&ethphy>;
};
};
&i2c {
status = "okay";
clock-frequency = <100000>;
#address-cells = <1>;
rtc@32 {
compatible = "ricoh,rs5c372a";
reg = <0x32>;
interrupt-parent = <&gpio0>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
};
};
&mdio {
status = "okay";
ethphy: ethernet-phy {
reg = <8>;
};
};
&pinctrl {
pinctrl-0 = <&pmx_rtc &pmx_power_led_ctrl>;
pinctrl-names = "default";
pmx_power_button: pmx-power-button {
marvell,pins = "mpp18";
marvell,function = "gpio";
};
pmx_power_led: pmx-power-led {
marvell,pins = "mpp16";
marvell,function = "gpio";
};
pmx_power_led_ctrl: pmx-power-led-ctrl {
marvell,pins = "mpp17";
marvell,function = "gpio";
};
pmx_rtc: pmx-rtc {
marvell,pins = "mpp3";
marvell,function = "gpio";
};
};
&sata {
pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
pinctrl-names = "default";
status = "okay";
nr-ports = <2>;
};
&uart0 {
status = "okay";
};