blob: d1d348b91c0a82d308186df2539d708a58da7aa8 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Device Tree file for Marvell Armada XP development board
* (DB-MV784MP-GP)
*
* Copyright (C) 2013-2014 Marvell
*
* Lior Amsalem <alior@marvell.com>
* Gregory CLEMENT <gregory.clement@free-electrons.com>
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
*
* Note: this Device Tree assumes that the bootloader has remapped the
* internal registers to 0xf1000000 (instead of the default
* 0xd0000000). The 0xf1000000 is the default used by the recent,
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
* boards were delivered with an older version of the bootloader that
* left internal registers mapped at 0xd0000000. If you are in this
* situation, you should either update your bootloader (preferred
* solution) or the below Device Tree should be adjusted.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "armada-xp-mv78460.dtsi"
/ {
model = "Marvell Armada XP Development Board DB-MV784MP-GP";
compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
/*
* 8 GB of plug-in RAM modules by default.The amount
* of memory available can be changed by the
* bootloader according the size of the module
* actually plugged. However, memory between
* 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
* the address range used for I/O (internal registers,
* MBus windows).
*/
reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
<0x00000001 0x00000000 0x00000001 0x00000000>;
};
cpus {
pm_pic {
ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>,
<&gpio0 17 GPIO_ACTIVE_LOW>,
<&gpio0 18 GPIO_ACTIVE_LOW>;
};
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000
MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>;
devbus-bootcs {
status = "okay";
/* Device Bus parameters are required */
/* Read parameters */
devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
devbus,acc-next-ps = <248000>;
devbus,rd-setup-ps = <0>;
devbus,rd-hold-ps = <0>;
/* Write parameters */
devbus,sync-enable = <0>;
devbus,wr-high-ps = <60000>;
devbus,wr-low-ps = <60000>;
devbus,ale-wr-ps = <60000>;
/* NOR 16 MiB */
nor@0 {
compatible = "cfi-flash";
reg = <0 0x1000000>;
bank-width = <2>;
};
};
internal-regs {
serial@12000 {
status = "okay";
};
serial@12100 {
status = "okay";
};
serial@12200 {
status = "okay";
};
serial@12300 {
status = "okay";
};
pinctrl {
pinctrl-0 = <&pic_pins>;
pinctrl-names = "default";
pic_pins: pic-pins-0 {
marvell,pins = "mpp16", "mpp17",
"mpp18";
marvell,function = "gpio";
};
};
sata@a0000 {
nr-ports = <2>;
status = "okay";
};
ethernet@70000 {
status = "okay";
phy = <&phy0>;
phy-mode = "qsgmii";
buffer-manager = <&bm>;
bm,pool-long = <0>;
};
ethernet@74000 {
status = "okay";
phy = <&phy1>;
phy-mode = "qsgmii";
buffer-manager = <&bm>;
bm,pool-long = <1>;
};
ethernet@30000 {
status = "okay";
phy = <&phy2>;
phy-mode = "qsgmii";
buffer-manager = <&bm>;
bm,pool-long = <2>;
};
ethernet@34000 {
status = "okay";
phy = <&phy3>;
phy-mode = "qsgmii";
buffer-manager = <&bm>;
bm,pool-long = <3>;
};
/* Front-side USB slot */
usb@50000 {
status = "okay";
};
/* Back-side USB slot */
usb@51000 {
status = "okay";
};
bm@c0000 {
status = "okay";
};
nand-controller@d0000 {
status = "okay";
nand@0 {
reg = <0>;
label = "pxa3xx_nand-0";
nand-rb = <0>;
nand-on-flash-bbt;
};
};
};
bm-bppi {
status = "okay";
};
};
};
&pciec {
status = "okay";
/*
* The 3 slots are physically present as
* standard PCIe slots on the board.
*/
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
pcie@9,0 {
/* Port 2, Lane 0 */
status = "okay";
};
pcie@a,0 {
/* Port 3, Lane 0 */
status = "okay";
};
};
&mdio {
phy0: ethernet-phy@0 {
reg = <16>;
};
phy1: ethernet-phy@1 {
reg = <17>;
};
phy2: ethernet-phy@2 {
reg = <18>;
};
phy3: ethernet-phy@3 {
reg = <19>;
};
};
&spi0 {
status = "okay";
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "n25q128a13", "jedec,spi-nor";
reg = <0>; /* Chip select 0 */
spi-max-frequency = <108000000>;
};
};