| #!/bin/bash |
| # SPDX-License-Identifier: GPL-2.0 |
| |
| # This test is for checking the A-TCAM and C-TCAM operation in Spectrum-2. |
| # It tries to exercise as many code paths in the eRP state machine as |
| # possible. |
| |
| lib_dir=$(dirname $0)/../../../../net/forwarding |
| |
| ALL_TESTS="single_mask_test identical_filters_test two_masks_test \ |
| multiple_masks_test ctcam_edge_cases_test delta_simple_test \ |
| delta_two_masks_one_key_test delta_simple_rehash_test \ |
| bloom_simple_test bloom_complex_test bloom_delta_test" |
| NUM_NETIFS=2 |
| source $lib_dir/tc_common.sh |
| source $lib_dir/devlink_lib.sh |
| |
| tcflags="skip_hw" |
| |
| h1_create() |
| { |
| simple_if_init $h1 192.0.2.1/24 198.51.100.1/24 |
| } |
| |
| h1_destroy() |
| { |
| simple_if_fini $h1 192.0.2.1/24 198.51.100.1/24 |
| } |
| |
| h2_create() |
| { |
| simple_if_init $h2 192.0.2.2/24 198.51.100.2/24 |
| tc qdisc add dev $h2 clsact |
| } |
| |
| h2_destroy() |
| { |
| tc qdisc del dev $h2 clsact |
| simple_if_fini $h2 192.0.2.2/24 198.51.100.2/24 |
| } |
| |
| tp_record() |
| { |
| local tracepoint=$1 |
| local cmd=$2 |
| |
| perf record -q -e $tracepoint $cmd |
| return $? |
| } |
| |
| tp_record_all() |
| { |
| local tracepoint=$1 |
| local seconds=$2 |
| |
| perf record -a -q -e $tracepoint sleep $seconds |
| return $? |
| } |
| |
| __tp_hit_count() |
| { |
| local tracepoint=$1 |
| |
| local perf_output=`perf script -F trace:event,trace` |
| return `echo $perf_output | grep "$tracepoint:" | wc -l` |
| } |
| |
| tp_check_hits() |
| { |
| local tracepoint=$1 |
| local count=$2 |
| |
| __tp_hit_count $tracepoint |
| if [[ "$?" -ne "$count" ]]; then |
| return 1 |
| fi |
| return 0 |
| } |
| |
| tp_check_hits_any() |
| { |
| local tracepoint=$1 |
| |
| __tp_hit_count $tracepoint |
| if [[ "$?" -eq "0" ]]; then |
| return 1 |
| fi |
| return 0 |
| } |
| |
| single_mask_test() |
| { |
| # When only a single mask is required, the device uses the master |
| # mask and not the eRP table. Verify that under this mode the right |
| # filter is matched |
| |
| RET=0 |
| |
| tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_err $? "Single filter - did not match" |
| |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 198.51.100.2 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 2 |
| check_err $? "Two filters - did not match highest priority" |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 198.51.100.1 -B 198.51.100.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Two filters - did not match lowest priority" |
| |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 198.51.100.1 -B 198.51.100.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 2 |
| check_err $? "Single filter - did not match after delete" |
| |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| |
| log_test "single mask test ($tcflags)" |
| } |
| |
| identical_filters_test() |
| { |
| # When two filters that only differ in their priority are used, |
| # one needs to be inserted into the C-TCAM. This test verifies |
| # that filters are correctly spilled to C-TCAM and that the right |
| # filter is matched |
| |
| RET=0 |
| |
| tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_err $? "Did not match A-TCAM filter" |
| |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Did not match C-TCAM filter after A-TCAM delete" |
| |
| tc filter add dev $h2 ingress protocol ip pref 3 handle 103 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 2 |
| check_err $? "Did not match C-TCAM filter after A-TCAM add" |
| |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_err $? "Did not match A-TCAM filter after C-TCAM delete" |
| |
| tc filter del dev $h2 ingress protocol ip pref 3 handle 103 flower |
| |
| log_test "identical filters test ($tcflags)" |
| } |
| |
| two_masks_test() |
| { |
| # When more than one mask is required, the eRP table is used. This |
| # test verifies that the eRP table is correctly allocated and used |
| |
| RET=0 |
| |
| tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| tc filter add dev $h2 ingress protocol ip pref 3 handle 103 flower \ |
| $tcflags dst_ip 192.0.0.0/8 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_err $? "Two filters - did not match highest priority" |
| |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_err $? "Single filter - did not match" |
| |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 192.0.2.0/24 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Two filters - did not match highest priority after add" |
| |
| tc filter del dev $h2 ingress protocol ip pref 3 handle 103 flower |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| |
| log_test "two masks test ($tcflags)" |
| } |
| |
| multiple_masks_test() |
| { |
| # The number of masks in a region is limited. Once the maximum |
| # number of masks has been reached filters that require new |
| # masks are spilled to the C-TCAM. This test verifies that |
| # spillage is performed correctly and that the right filter is |
| # matched |
| |
| if [[ "$tcflags" != "skip_sw" ]]; then |
| return 0; |
| fi |
| |
| local index |
| |
| RET=0 |
| |
| NUM_MASKS=32 |
| NUM_ERPS=16 |
| BASE_INDEX=100 |
| |
| for i in $(eval echo {1..$NUM_MASKS}); do |
| index=$((BASE_INDEX - i)) |
| |
| if ((i > NUM_ERPS)); then |
| exp_hits=1 |
| err_msg="$i filters - C-TCAM spill did not happen when it was expected" |
| else |
| exp_hits=0 |
| err_msg="$i filters - C-TCAM spill happened when it should not" |
| fi |
| |
| tp_record "mlxsw:mlxsw_sp_acl_atcam_entry_add_ctcam_spill" \ |
| "tc filter add dev $h2 ingress protocol ip pref $index \ |
| handle $index \ |
| flower $tcflags \ |
| dst_ip 192.0.2.2/${i} src_ip 192.0.2.1/${i} \ |
| action drop" |
| tp_check_hits "mlxsw:mlxsw_sp_acl_atcam_entry_add_ctcam_spill" \ |
| $exp_hits |
| check_err $? "$err_msg" |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 \ |
| -B 192.0.2.2 -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" $index 1 |
| check_err $? "$i filters - did not match highest priority (add)" |
| done |
| |
| for i in $(eval echo {$NUM_MASKS..1}); do |
| index=$((BASE_INDEX - i)) |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 \ |
| -B 192.0.2.2 -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" $index 2 |
| check_err $? "$i filters - did not match highest priority (del)" |
| |
| tc filter del dev $h2 ingress protocol ip pref $index \ |
| handle $index flower |
| done |
| |
| log_test "multiple masks test ($tcflags)" |
| } |
| |
| ctcam_two_atcam_masks_test() |
| { |
| RET=0 |
| |
| # First case: C-TCAM is disabled when there are two A-TCAM masks. |
| # We push a filter into the C-TCAM by using two identical filters |
| # as in identical_filters_test() |
| |
| # Filter goes into A-TCAM |
| tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| # Filter goes into C-TCAM |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| # Filter goes into A-TCAM |
| tc filter add dev $h2 ingress protocol ip pref 3 handle 103 flower \ |
| $tcflags dst_ip 192.0.0.0/16 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_err $? "Did not match A-TCAM filter" |
| |
| # Delete both A-TCAM and C-TCAM filters and make sure the remaining |
| # A-TCAM filter still works |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_err $? "Did not match A-TCAM filter" |
| |
| tc filter del dev $h2 ingress protocol ip pref 3 handle 103 flower |
| |
| log_test "ctcam with two atcam masks test ($tcflags)" |
| } |
| |
| ctcam_one_atcam_mask_test() |
| { |
| RET=0 |
| |
| # Second case: C-TCAM is disabled when there is one A-TCAM mask. |
| # The test is similar to identical_filters_test() |
| |
| # Filter goes into A-TCAM |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| # Filter goes into C-TCAM |
| tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_err $? "Did not match C-TCAM filter" |
| |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Did not match A-TCAM filter" |
| |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| |
| log_test "ctcam with one atcam mask test ($tcflags)" |
| } |
| |
| ctcam_no_atcam_masks_test() |
| { |
| RET=0 |
| |
| # Third case: C-TCAM is disabled when there are no A-TCAM masks |
| # This test exercises the code path that transitions the eRP table |
| # to its initial state after deleting the last C-TCAM mask |
| |
| # Filter goes into A-TCAM |
| tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| # Filter goes into C-TCAM |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| |
| log_test "ctcam with no atcam masks test ($tcflags)" |
| } |
| |
| ctcam_edge_cases_test() |
| { |
| # When the C-TCAM is disabled after deleting the last C-TCAM |
| # mask, we want to make sure the eRP state machine is put in |
| # the correct state |
| |
| ctcam_two_atcam_masks_test |
| ctcam_one_atcam_mask_test |
| ctcam_no_atcam_masks_test |
| } |
| |
| delta_simple_test() |
| { |
| # The first filter will create eRP, the second filter will fit into |
| # the first eRP with delta. Remove the first rule then and check that |
| # the eRP stays (referenced by the second filter). |
| |
| RET=0 |
| |
| if [[ "$tcflags" != "skip_sw" ]]; then |
| return 0; |
| fi |
| |
| tp_record "objagg:*" "tc filter add dev $h2 ingress protocol ip \ |
| pref 1 handle 101 flower $tcflags dst_ip 192.0.0.0/24 \ |
| action drop" |
| tp_check_hits "objagg:objagg_obj_root_create" 1 |
| check_err $? "eRP was not created" |
| |
| tp_record "objagg:*" "tc filter add dev $h2 ingress protocol ip \ |
| pref 2 handle 102 flower $tcflags dst_ip 192.0.2.2 \ |
| action drop" |
| tp_check_hits "objagg:objagg_obj_root_create" 0 |
| check_err $? "eRP was incorrectly created" |
| tp_check_hits "objagg:objagg_obj_parent_assign" 1 |
| check_err $? "delta was not created" |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_fail $? "Matched a wrong filter" |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Did not match on correct filter" |
| |
| tp_record "objagg:*" "tc filter del dev $h2 ingress protocol ip \ |
| pref 1 handle 101 flower" |
| tp_check_hits "objagg:objagg_obj_root_destroy" 0 |
| check_err $? "eRP was incorrectly destroyed" |
| tp_check_hits "objagg:objagg_obj_parent_unassign" 0 |
| check_err $? "delta was incorrectly destroyed" |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 2 |
| check_err $? "Did not match on correct filter after the first was removed" |
| |
| tp_record "objagg:*" "tc filter del dev $h2 ingress protocol ip \ |
| pref 2 handle 102 flower" |
| tp_check_hits "objagg:objagg_obj_parent_unassign" 1 |
| check_err $? "delta was not destroyed" |
| tp_check_hits "objagg:objagg_obj_root_destroy" 1 |
| check_err $? "eRP was not destroyed" |
| |
| log_test "delta simple test ($tcflags)" |
| } |
| |
| delta_two_masks_one_key_test() |
| { |
| # If 2 keys are the same and only differ in mask in a way that |
| # they belong under the same ERP (second is delta of the first), |
| # there should be no C-TCAM spill. |
| |
| RET=0 |
| |
| if [[ "$tcflags" != "skip_sw" ]]; then |
| return 0; |
| fi |
| |
| tp_record "mlxsw:*" "tc filter add dev $h2 ingress protocol ip \ |
| pref 1 handle 101 flower $tcflags dst_ip 192.0.2.0/24 \ |
| action drop" |
| tp_check_hits "mlxsw:mlxsw_sp_acl_atcam_entry_add_ctcam_spill" 0 |
| check_err $? "incorrect C-TCAM spill while inserting the first rule" |
| |
| tp_record "mlxsw:*" "tc filter add dev $h2 ingress protocol ip \ |
| pref 2 handle 102 flower $tcflags dst_ip 192.0.2.2 \ |
| action drop" |
| tp_check_hits "mlxsw:mlxsw_sp_acl_atcam_entry_add_ctcam_spill" 0 |
| check_err $? "incorrect C-TCAM spill while inserting the second rule" |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_err $? "Did not match on correct filter" |
| |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Did not match on correct filter" |
| |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| |
| log_test "delta two masks one key test ($tcflags)" |
| } |
| |
| delta_simple_rehash_test() |
| { |
| RET=0 |
| |
| if [[ "$tcflags" != "skip_sw" ]]; then |
| return 0; |
| fi |
| |
| devlink dev param set $DEVLINK_DEV \ |
| name acl_region_rehash_interval cmode runtime value 0 |
| check_err $? "Failed to set ACL region rehash interval" |
| |
| tp_record_all mlxsw:mlxsw_sp_acl_tcam_vregion_rehash 7 |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_rehash |
| check_fail $? "Rehash trace was hit even when rehash should be disabled" |
| |
| devlink dev param set $DEVLINK_DEV \ |
| name acl_region_rehash_interval cmode runtime value 3000 |
| check_err $? "Failed to set ACL region rehash interval" |
| |
| sleep 1 |
| |
| tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \ |
| $tcflags dst_ip 192.0.1.0/25 action drop |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| tc filter add dev $h2 ingress protocol ip pref 3 handle 103 flower \ |
| $tcflags dst_ip 192.0.3.0/24 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_fail $? "Matched a wrong filter" |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_fail $? "Matched a wrong filter" |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Did not match on correct filter" |
| |
| tp_record_all mlxsw:* 3 |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_rehash |
| check_err $? "Rehash trace was not hit" |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_migrate |
| check_err $? "Migrate trace was not hit" |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_migrate_end |
| check_err $? "Migrate end trace was not hit" |
| tp_record_all mlxsw:* 3 |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_rehash |
| check_err $? "Rehash trace was not hit" |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_migrate |
| check_fail $? "Migrate trace was hit when no migration should happen" |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_migrate_end |
| check_fail $? "Migrate end trace was hit when no migration should happen" |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_fail $? "Matched a wrong filter after rehash" |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_fail $? "Matched a wrong filter after rehash" |
| |
| tc_check_packets "dev $h2 ingress" 102 2 |
| check_err $? "Did not match on correct filter after rehash" |
| |
| tc filter del dev $h2 ingress protocol ip pref 3 handle 103 flower |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| |
| log_test "delta simple rehash test ($tcflags)" |
| } |
| |
| delta_simple_ipv6_rehash_test() |
| { |
| RET=0 |
| |
| if [[ "$tcflags" != "skip_sw" ]]; then |
| return 0; |
| fi |
| |
| devlink dev param set $DEVLINK_DEV \ |
| name acl_region_rehash_interval cmode runtime value 0 |
| check_err $? "Failed to set ACL region rehash interval" |
| |
| tp_record_all mlxsw:mlxsw_sp_acl_tcam_vregion_rehash 7 |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_rehash |
| check_fail $? "Rehash trace was hit even when rehash should be disabled" |
| |
| devlink dev param set $DEVLINK_DEV \ |
| name acl_region_rehash_interval cmode runtime value 3000 |
| check_err $? "Failed to set ACL region rehash interval" |
| |
| sleep 1 |
| |
| tc filter add dev $h2 ingress protocol ipv6 pref 1 handle 101 flower \ |
| $tcflags dst_ip 2001:db8:1::0/121 action drop |
| tc filter add dev $h2 ingress protocol ipv6 pref 2 handle 102 flower \ |
| $tcflags dst_ip 2001:db8:2::2 action drop |
| tc filter add dev $h2 ingress protocol ipv6 pref 3 handle 103 flower \ |
| $tcflags dst_ip 2001:db8:3::0/120 action drop |
| |
| $MZ $h1 -6 -c 1 -p 64 -a $h1mac -b $h2mac \ |
| -A 2001:db8:2::1 -B 2001:db8:2::2 -t udp -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_fail $? "Matched a wrong filter" |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_fail $? "Matched a wrong filter" |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Did not match on correct filter" |
| |
| tp_record_all mlxsw:* 3 |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_rehash |
| check_err $? "Rehash trace was not hit" |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_migrate |
| check_err $? "Migrate trace was not hit" |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_migrate_end |
| check_err $? "Migrate end trace was not hit" |
| tp_record_all mlxsw:* 3 |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_rehash |
| check_err $? "Rehash trace was not hit" |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_migrate |
| check_fail $? "Migrate trace was hit when no migration should happen" |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_migrate_end |
| check_fail $? "Migrate end trace was hit when no migration should happen" |
| |
| $MZ $h1 -6 -c 1 -p 64 -a $h1mac -b $h2mac \ |
| -A 2001:db8:2::1 -B 2001:db8:2::2 -t udp -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_fail $? "Matched a wrong filter after rehash" |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_fail $? "Matched a wrong filter after rehash" |
| |
| tc_check_packets "dev $h2 ingress" 102 2 |
| check_err $? "Did not match on correct filter after rehash" |
| |
| tc filter del dev $h2 ingress protocol ipv6 pref 3 handle 103 flower |
| tc filter del dev $h2 ingress protocol ipv6 pref 2 handle 102 flower |
| tc filter del dev $h2 ingress protocol ipv6 pref 1 handle 101 flower |
| |
| log_test "delta simple IPv6 rehash test ($tcflags)" |
| } |
| |
| TEST_RULE_BASE=256 |
| declare -a test_rules_inserted |
| |
| test_rule_add() |
| { |
| local iface=$1 |
| local tcflags=$2 |
| local index=$3 |
| |
| if ! [ ${test_rules_inserted[$index]} ] ; then |
| test_rules_inserted[$index]=false |
| fi |
| if ${test_rules_inserted[$index]} ; then |
| return |
| fi |
| |
| local number=$(( $index + $TEST_RULE_BASE )) |
| printf -v hexnumber '%x' $number |
| |
| batch="${batch}filter add dev $iface ingress protocol ipv6 pref 1 \ |
| handle $number flower $tcflags \ |
| src_ip 2001:db8:1::$hexnumber action drop\n" |
| test_rules_inserted[$index]=true |
| } |
| |
| test_rule_del() |
| { |
| local iface=$1 |
| local index=$2 |
| |
| if ! [ ${test_rules_inserted[$index]} ] ; then |
| test_rules_inserted[$index]=false |
| fi |
| if ! ${test_rules_inserted[$index]} ; then |
| return |
| fi |
| |
| local number=$(( $index + $TEST_RULE_BASE )) |
| printf -v hexnumber '%x' $number |
| |
| batch="${batch}filter del dev $iface ingress protocol ipv6 pref 1 \ |
| handle $number flower\n" |
| test_rules_inserted[$index]=false |
| } |
| |
| test_rule_add_or_remove() |
| { |
| local iface=$1 |
| local tcflags=$2 |
| local index=$3 |
| |
| if ! [ ${test_rules_inserted[$index]} ] ; then |
| test_rules_inserted[$index]=false |
| fi |
| if ${test_rules_inserted[$index]} ; then |
| test_rule_del $iface $index |
| else |
| test_rule_add $iface $tcflags $index |
| fi |
| } |
| |
| test_rule_add_or_remove_random_batch() |
| { |
| local iface=$1 |
| local tcflags=$2 |
| local total_count=$3 |
| local skip=0 |
| local count=0 |
| local MAXSKIP=20 |
| local MAXCOUNT=20 |
| |
| for ((i=1;i<=total_count;i++)); do |
| if (( $skip == 0 )) && (($count == 0)); then |
| ((skip=$RANDOM % $MAXSKIP + 1)) |
| ((count=$RANDOM % $MAXCOUNT + 1)) |
| fi |
| if (( $skip != 0 )); then |
| ((skip-=1)) |
| else |
| ((count-=1)) |
| test_rule_add_or_remove $iface $tcflags $i |
| fi |
| done |
| } |
| |
| delta_massive_ipv6_rehash_test() |
| { |
| RET=0 |
| |
| if [[ "$tcflags" != "skip_sw" ]]; then |
| return 0; |
| fi |
| |
| devlink dev param set $DEVLINK_DEV \ |
| name acl_region_rehash_interval cmode runtime value 0 |
| check_err $? "Failed to set ACL region rehash interval" |
| |
| tp_record_all mlxsw:mlxsw_sp_acl_tcam_vregion_rehash 7 |
| tp_check_hits_any mlxsw:mlxsw_sp_acl_tcam_vregion_rehash |
| check_fail $? "Rehash trace was hit even when rehash should be disabled" |
| |
| RANDOM=4432897 |
| declare batch="" |
| test_rule_add_or_remove_random_batch $h2 $tcflags 5000 |
| |
| echo -n -e $batch | tc -b - |
| |
| declare batch="" |
| test_rule_add_or_remove_random_batch $h2 $tcflags 5000 |
| |
| devlink dev param set $DEVLINK_DEV \ |
| name acl_region_rehash_interval cmode runtime value 3000 |
| check_err $? "Failed to set ACL region rehash interval" |
| |
| sleep 1 |
| |
| tc filter add dev $h2 ingress protocol ipv6 pref 1 handle 101 flower \ |
| $tcflags dst_ip 2001:db8:1::0/121 action drop |
| tc filter add dev $h2 ingress protocol ipv6 pref 2 handle 102 flower \ |
| $tcflags dst_ip 2001:db8:2::2 action drop |
| tc filter add dev $h2 ingress protocol ipv6 pref 3 handle 103 flower \ |
| $tcflags dst_ip 2001:db8:3::0/120 action drop |
| |
| $MZ $h1 -6 -c 1 -p 64 -a $h1mac -b $h2mac \ |
| -A 2001:db8:2::1 -B 2001:db8:2::2 -t udp -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_fail $? "Matched a wrong filter" |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_fail $? "Matched a wrong filter" |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Did not match on correct filter" |
| |
| echo -n -e $batch | tc -b - |
| |
| devlink dev param set $DEVLINK_DEV \ |
| name acl_region_rehash_interval cmode runtime value 0 |
| check_err $? "Failed to set ACL region rehash interval" |
| |
| $MZ $h1 -6 -c 1 -p 64 -a $h1mac -b $h2mac \ |
| -A 2001:db8:2::1 -B 2001:db8:2::2 -t udp -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_fail $? "Matched a wrong filter after rehash" |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_fail $? "Matched a wrong filter after rehash" |
| |
| tc_check_packets "dev $h2 ingress" 102 2 |
| check_err $? "Did not match on correct filter after rehash" |
| |
| tc filter del dev $h2 ingress protocol ipv6 pref 3 handle 103 flower |
| tc filter del dev $h2 ingress protocol ipv6 pref 2 handle 102 flower |
| tc filter del dev $h2 ingress protocol ipv6 pref 1 handle 101 flower |
| |
| declare batch="" |
| for i in {1..5000}; do |
| test_rule_del $h2 $tcflags $i |
| done |
| echo -e $batch | tc -b - |
| |
| log_test "delta massive IPv6 rehash test ($tcflags)" |
| } |
| |
| bloom_simple_test() |
| { |
| # Bloom filter requires that the eRP table is used. This test |
| # verifies that Bloom filter is not harming correctness of ACLs. |
| # First, make sure that eRP table is used and then set rule patterns |
| # which are distant enough and will result skipping a lookup after |
| # consulting the Bloom filter. Although some eRP lookups are skipped, |
| # the correct filter should be hit. |
| |
| RET=0 |
| |
| tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \ |
| $tcflags dst_ip 192.0.2.2 action drop |
| tc filter add dev $h2 ingress protocol ip pref 5 handle 104 flower \ |
| $tcflags dst_ip 198.51.100.2 action drop |
| tc filter add dev $h2 ingress protocol ip pref 3 handle 103 flower \ |
| $tcflags dst_ip 192.0.0.0/8 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 101 1 |
| check_err $? "Two filters - did not match highest priority" |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 198.51.100.1 -B 198.51.100.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 104 1 |
| check_err $? "Single filter - did not match" |
| |
| tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_err $? "Low prio filter - did not match" |
| |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 198.0.0.0/8 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 198.51.100.1 -B 198.51.100.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Two filters - did not match highest priority after add" |
| |
| tc filter del dev $h2 ingress protocol ip pref 3 handle 103 flower |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| tc filter del dev $h2 ingress protocol ip pref 5 handle 104 flower |
| |
| log_test "bloom simple test ($tcflags)" |
| } |
| |
| bloom_complex_test() |
| { |
| # Bloom filter index computation is affected from region ID, eRP |
| # ID and from the region key size. In order to excercise those parts |
| # of the Bloom filter code, use a series of regions, each with a |
| # different key size and send packet that should hit all of them. |
| local index |
| |
| RET=0 |
| NUM_CHAINS=4 |
| BASE_INDEX=100 |
| |
| # Create chain with up to 2 key blocks (ip_proto only) |
| tc chain add dev $h2 ingress chain 1 protocol ip flower \ |
| ip_proto tcp &> /dev/null |
| # Create chain with 2-4 key blocks (ip_proto, src MAC) |
| tc chain add dev $h2 ingress chain 2 protocol ip flower \ |
| ip_proto tcp \ |
| src_mac 00:00:00:00:00:00/FF:FF:FF:FF:FF:FF &> /dev/null |
| # Create chain with 4-8 key blocks (ip_proto, src & dst MAC, IPv4 dest) |
| tc chain add dev $h2 ingress chain 3 protocol ip flower \ |
| ip_proto tcp \ |
| dst_mac 00:00:00:00:00:00/FF:FF:FF:FF:FF:FF \ |
| src_mac 00:00:00:00:00:00/FF:FF:FF:FF:FF:FF \ |
| dst_ip 0.0.0.0/32 &> /dev/null |
| # Default chain contains all fields and therefore is 8-12 key blocks |
| tc chain add dev $h2 ingress chain 4 |
| |
| # We need at least 2 rules in every region to have eRP table active |
| # so create a dummy rule per chain using a different pattern |
| for i in $(eval echo {0..$NUM_CHAINS}); do |
| index=$((BASE_INDEX - 1 - i)) |
| tc filter add dev $h2 ingress chain $i protocol ip \ |
| pref 2 handle $index flower \ |
| $tcflags ip_proto tcp action drop |
| done |
| |
| # Add rules to test Bloom filter, each in a different chain |
| index=$BASE_INDEX |
| tc filter add dev $h2 ingress protocol ip \ |
| pref 1 handle $((++index)) flower \ |
| $tcflags dst_ip 192.0.0.0/16 action goto chain 1 |
| tc filter add dev $h2 ingress chain 1 protocol ip \ |
| pref 1 handle $((++index)) flower \ |
| $tcflags action goto chain 2 |
| tc filter add dev $h2 ingress chain 2 protocol ip \ |
| pref 1 handle $((++index)) flower \ |
| $tcflags src_mac $h1mac action goto chain 3 |
| tc filter add dev $h2 ingress chain 3 protocol ip \ |
| pref 1 handle $((++index)) flower \ |
| $tcflags dst_ip 192.0.0.0/8 action goto chain 4 |
| tc filter add dev $h2 ingress chain 4 protocol ip \ |
| pref 1 handle $((++index)) flower \ |
| $tcflags src_ip 192.0.2.0/24 action drop |
| |
| # Send a packet that is supposed to hit all chains |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \ |
| -t ip -q |
| |
| for i in $(eval echo {0..$NUM_CHAINS}); do |
| index=$((BASE_INDEX + i + 1)) |
| tc_check_packets "dev $h2 ingress" $index 1 |
| check_err $? "Did not match chain $i" |
| done |
| |
| # Rules cleanup |
| for i in $(eval echo {$NUM_CHAINS..0}); do |
| index=$((BASE_INDEX - i - 1)) |
| tc filter del dev $h2 ingress chain $i \ |
| pref 2 handle $index flower |
| index=$((BASE_INDEX + i + 1)) |
| tc filter del dev $h2 ingress chain $i \ |
| pref 1 handle $index flower |
| done |
| |
| # Chains cleanup |
| for i in $(eval echo {$NUM_CHAINS..1}); do |
| tc chain del dev $h2 ingress chain $i |
| done |
| |
| log_test "bloom complex test ($tcflags)" |
| } |
| |
| |
| bloom_delta_test() |
| { |
| # When multiple masks are used, the eRP table is activated. When |
| # masks are close enough (delta) the masks reside on the same |
| # eRP table. This test verifies that the eRP table is correctly |
| # allocated and used in delta condition and that Bloom filter is |
| # still functional with delta. |
| |
| RET=0 |
| |
| tc filter add dev $h2 ingress protocol ip pref 3 handle 103 flower \ |
| $tcflags dst_ip 192.1.0.0/16 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.1.2.1 -B 192.1.2.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 103 1 |
| check_err $? "Single filter - did not match" |
| |
| tc filter add dev $h2 ingress protocol ip pref 2 handle 102 flower \ |
| $tcflags dst_ip 192.2.1.0/24 action drop |
| |
| $MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.2.1.1 -B 192.2.1.2 \ |
| -t ip -q |
| |
| tc_check_packets "dev $h2 ingress" 102 1 |
| check_err $? "Delta filters - did not match second filter" |
| |
| tc filter del dev $h2 ingress protocol ip pref 3 handle 103 flower |
| tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower |
| |
| log_test "bloom delta test ($tcflags)" |
| } |
| |
| setup_prepare() |
| { |
| h1=${NETIFS[p1]} |
| h2=${NETIFS[p2]} |
| h1mac=$(mac_get $h1) |
| h2mac=$(mac_get $h2) |
| |
| vrf_prepare |
| |
| h1_create |
| h2_create |
| } |
| |
| cleanup() |
| { |
| pre_cleanup |
| |
| h2_destroy |
| h1_destroy |
| |
| vrf_cleanup |
| } |
| |
| trap cleanup EXIT |
| |
| setup_prepare |
| setup_wait |
| |
| tests_run |
| |
| if ! tc_offload_check; then |
| check_err 1 "Could not test offloaded functionality" |
| log_test "mlxsw-specific tests for tc flower" |
| exit |
| else |
| tcflags="skip_sw" |
| tests_run |
| fi |
| |
| exit $EXIT_STATUS |