| /* SPDX-License-Identifier: GPL-2.0 */ |
| /****************************************************************************** |
| * |
| * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved. |
| * |
| ******************************************************************************/ |
| #ifndef __HAL_DATA_H__ |
| #define __HAL_DATA_H__ |
| |
| #include "odm_precomp.h" |
| #include <hal_btcoex.h> |
| |
| #include <hal_sdio.h> |
| |
| /* */ |
| /* <Roger_Notes> For RTL8723 WiFi/BT/GPS multi-function configuration. 2010.10.06. */ |
| /* */ |
| enum RT_MULTI_FUNC { |
| RT_MULTI_FUNC_NONE = 0x00, |
| RT_MULTI_FUNC_WIFI = 0x01, |
| RT_MULTI_FUNC_BT = 0x02, |
| RT_MULTI_FUNC_GPS = 0x04, |
| }; |
| /* */ |
| /* <Roger_Notes> For RTL8723 WiFi PDn/GPIO polarity control configuration. 2010.10.08. */ |
| /* */ |
| enum RT_POLARITY_CTL { |
| RT_POLARITY_LOW_ACT = 0, |
| RT_POLARITY_HIGH_ACT = 1, |
| }; |
| |
| /* For RTL8723 regulator mode. by tynli. 2011.01.14. */ |
| enum RT_REGULATOR_MODE { |
| RT_SWITCHING_REGULATOR = 0, |
| RT_LDO_REGULATOR = 1, |
| }; |
| |
| enum RT_AMPDU_BURST { |
| RT_AMPDU_BURST_NONE = 0, |
| RT_AMPDU_BURST_92D = 1, |
| RT_AMPDU_BURST_88E = 2, |
| RT_AMPDU_BURST_8812_4 = 3, |
| RT_AMPDU_BURST_8812_8 = 4, |
| RT_AMPDU_BURST_8812_12 = 5, |
| RT_AMPDU_BURST_8812_15 = 6, |
| RT_AMPDU_BURST_8723B = 7, |
| }; |
| |
| #define CHANNEL_MAX_NUMBER 14+24+21 /* 14 is the max channel number */ |
| #define CHANNEL_MAX_NUMBER_2G 14 |
| #define CHANNEL_MAX_NUMBER_5G 54 /* Please refer to "phy_GetChnlGroup8812A" and "Hal_ReadTxPowerInfo8812A" */ |
| #define CHANNEL_MAX_NUMBER_5G_80M 7 |
| #define CHANNEL_GROUP_MAX 3+9 /* ch1~3, ch4~9, ch10~14 total three groups */ |
| #define MAX_PG_GROUP 13 |
| |
| /* Tx Power Limit Table Size */ |
| #define MAX_REGULATION_NUM 4 |
| #define MAX_RF_PATH_NUM_IN_POWER_LIMIT_TABLE 4 |
| #define MAX_2_4G_BANDWITH_NUM 4 |
| #define MAX_RATE_SECTION_NUM 10 |
| #define MAX_5G_BANDWITH_NUM 4 |
| |
| #define MAX_BASE_NUM_IN_PHY_REG_PG_2_4G 10 /* CCK:1, OFDM:1, HT:4, VHT:4 */ |
| #define MAX_BASE_NUM_IN_PHY_REG_PG_5G 9 /* OFDM:1, HT:4, VHT:4 */ |
| |
| |
| /* duplicate code, will move to ODM ######### */ |
| /* define IQK_MAC_REG_NUM 4 */ |
| /* define IQK_ADDA_REG_NUM 16 */ |
| |
| /* define IQK_BB_REG_NUM 10 */ |
| #define IQK_BB_REG_NUM_92C 9 |
| #define IQK_BB_REG_NUM_92D 10 |
| #define IQK_BB_REG_NUM_test 6 |
| |
| #define IQK_Matrix_Settings_NUM_92D 1+24+21 |
| |
| /* define HP_THERMAL_NUM 8 */ |
| /* duplicate code, will move to ODM ######### */ |
| |
| enum { |
| SINGLEMAC_SINGLEPHY, /* SMSP */ |
| DUALMAC_DUALPHY, /* DMDP */ |
| DUALMAC_SINGLEPHY, /* DMSP */ |
| }; |
| |
| #define PAGE_SIZE_128 128 |
| #define PAGE_SIZE_256 256 |
| #define PAGE_SIZE_512 512 |
| |
| struct dm_priv { |
| u8 DM_Type; |
| |
| #define DYNAMIC_FUNC_BT BIT0 |
| |
| u8 DMFlag; |
| u8 InitDMFlag; |
| /* u8 RSVD_1; */ |
| |
| u32 InitODMFlag; |
| /* Upper and Lower Signal threshold for Rate Adaptive */ |
| int UndecoratedSmoothedPWDB; |
| int UndecoratedSmoothedCCK; |
| int EntryMinUndecoratedSmoothedPWDB; |
| int EntryMaxUndecoratedSmoothedPWDB; |
| int MinUndecoratedPWDBForDM; |
| int LastMinUndecoratedPWDBForDM; |
| |
| s32 UndecoratedSmoothedBeacon; |
| |
| /* duplicate code, will move to ODM ######### */ |
| /* for High Power */ |
| u8 bDynamicTxPowerEnable; |
| u8 LastDTPLvl; |
| u8 DynamicTxHighPowerLvl;/* Add by Jacken Tx Power Control for Near/Far Range 2008/03/06 */ |
| |
| /* for tx power tracking */ |
| u8 bTXPowerTracking; |
| u8 TXPowercount; |
| u8 bTXPowerTrackingInit; |
| u8 TxPowerTrackControl; /* for mp mode, turn off txpwrtracking as default */ |
| u8 TM_Trigger; |
| |
| u8 ThermalMeter[2]; /* ThermalMeter, index 0 for RFIC0, and 1 for RFIC1 */ |
| u8 ThermalValue; |
| u8 ThermalValue_LCK; |
| u8 ThermalValue_IQK; |
| u8 ThermalValue_DPK; |
| u8 bRfPiEnable; |
| /* u8 RSVD_2; */ |
| |
| /* for APK */ |
| u32 APKoutput[2][2]; /* path A/B; output1_1a/output1_2a */ |
| u8 bAPKdone; |
| u8 bAPKThermalMeterIgnore; |
| u8 bDPdone; |
| u8 bDPPathAOK; |
| u8 bDPPathBOK; |
| /* u8 RSVD_3; */ |
| /* u8 RSVD_4; */ |
| /* u8 RSVD_5; */ |
| |
| /* for IQK */ |
| u32 ADDA_backup[IQK_ADDA_REG_NUM]; |
| u32 IQK_MAC_backup[IQK_MAC_REG_NUM]; |
| u32 IQK_BB_backup_recover[9]; |
| u32 IQK_BB_backup[IQK_BB_REG_NUM]; |
| |
| u8 PowerIndex_backup[6]; |
| u8 OFDM_index[2]; |
| |
| u8 bCCKinCH14; |
| u8 CCK_index; |
| u8 bDoneTxpower; |
| u8 CCK_index_HP; |
| |
| u8 OFDM_index_HP[2]; |
| u8 ThermalValue_HP[HP_THERMAL_NUM]; |
| u8 ThermalValue_HP_index; |
| /* u8 RSVD_6; */ |
| |
| /* for TxPwrTracking2 */ |
| s32 RegE94; |
| s32 RegE9C; |
| s32 RegEB4; |
| s32 RegEBC; |
| |
| u32 TXPowerTrackingCallbackCnt; /* cosa add for debug */ |
| |
| u32 prv_traffic_idx; /* edca turbo */ |
| /* duplicate code, will move to ODM ######### */ |
| |
| /* Add for Reading Initial Data Rate SEL Register 0x484 during watchdog. Using for fill tx desc. 2011.3.21 by Thomas */ |
| u8 INIDATA_RATE[32]; |
| }; |
| |
| |
| struct hal_com_data { |
| HAL_VERSION VersionID; |
| enum RT_MULTI_FUNC MultiFunc; /* For multi-function consideration. */ |
| enum RT_POLARITY_CTL PolarityCtl; /* For Wifi PDn Polarity control. */ |
| enum RT_REGULATOR_MODE RegulatorMode; /* switching regulator or LDO */ |
| |
| u16 FirmwareVersion; |
| u16 FirmwareVersionRev; |
| u16 FirmwareSubVersion; |
| u16 FirmwareSignature; |
| |
| /* current WIFI_PHY values */ |
| enum WIRELESS_MODE CurrentWirelessMode; |
| enum CHANNEL_WIDTH CurrentChannelBW; |
| enum BAND_TYPE CurrentBandType; /* 0:2.4G, 1:5G */ |
| enum BAND_TYPE BandSet; |
| u8 CurrentChannel; |
| u8 CurrentCenterFrequencyIndex1; |
| u8 nCur40MhzPrimeSC;/* Control channel sub-carrier */ |
| u8 nCur80MhzPrimeSC; /* used for primary 40MHz of 80MHz mode */ |
| |
| u16 CustomerID; |
| u16 BasicRateSet; |
| u16 ForcedDataRate;/* Force Data Rate. 0: Auto, 0x02: 1M ~ 0x6C: 54M. */ |
| u32 ReceiveConfig; |
| |
| /* rf_ctrl */ |
| u8 rf_chip; |
| u8 rf_type; |
| u8 PackageType; |
| u8 NumTotalRFPath; |
| |
| u8 InterfaceSel; |
| u8 framesync; |
| u32 framesyncC34; |
| u8 framesyncMonitor; |
| u8 DefaultInitialGain[4]; |
| /* EEPROM setting. */ |
| u16 EEPROMVID; |
| u16 EEPROMSVID; |
| |
| u8 EEPROMCustomerID; |
| u8 EEPROMSubCustomerID; |
| u8 EEPROMVersion; |
| u8 EEPROMRegulatory; |
| u8 EEPROMThermalMeter; |
| u8 EEPROMBluetoothCoexist; |
| u8 EEPROMBluetoothType; |
| u8 EEPROMBluetoothAntNum; |
| u8 EEPROMBluetoothAntIsolation; |
| u8 EEPROMBluetoothRadioShared; |
| u8 bTXPowerDataReadFromEEPORM; |
| u8 bAPKThermalMeterIgnore; |
| u8 bDisableSWChannelPlan; /* flag of disable software change channel plan */ |
| |
| bool EepromOrEfuse; |
| u8 EfuseUsedPercentage; |
| u16 EfuseUsedBytes; |
| EFUSE_HAL EfuseHal; |
| |
| /* 3 [2.4G] */ |
| u8 Index24G_CCK_Base[MAX_RF_PATH][CHANNEL_MAX_NUMBER]; |
| u8 Index24G_BW40_Base[MAX_RF_PATH][CHANNEL_MAX_NUMBER]; |
| /* If only one tx, only BW20 and OFDM are used. */ |
| s8 CCK_24G_Diff[MAX_RF_PATH][MAX_TX_COUNT]; |
| s8 OFDM_24G_Diff[MAX_RF_PATH][MAX_TX_COUNT]; |
| s8 BW20_24G_Diff[MAX_RF_PATH][MAX_TX_COUNT]; |
| s8 BW40_24G_Diff[MAX_RF_PATH][MAX_TX_COUNT]; |
| /* 3 [5G] */ |
| u8 Index5G_BW40_Base[MAX_RF_PATH][CHANNEL_MAX_NUMBER]; |
| u8 Index5G_BW80_Base[MAX_RF_PATH][CHANNEL_MAX_NUMBER_5G_80M]; |
| s8 OFDM_5G_Diff[MAX_RF_PATH][MAX_TX_COUNT]; |
| s8 BW20_5G_Diff[MAX_RF_PATH][MAX_TX_COUNT]; |
| s8 BW40_5G_Diff[MAX_RF_PATH][MAX_TX_COUNT]; |
| s8 BW80_5G_Diff[MAX_RF_PATH][MAX_TX_COUNT]; |
| |
| u8 Regulation2_4G; |
| u8 Regulation5G; |
| |
| u8 TxPwrInPercentage; |
| |
| u8 TxPwrCalibrateRate; |
| /* TX power by rate table at most 4RF path. */ |
| /* The register is */ |
| /* VHT TX power by rate off setArray = */ |
| /* Band:-2G&5G = 0 / 1 */ |
| /* RF: at most 4*4 = ABCD = 0/1/2/3 */ |
| /* CCK = 0 OFDM = 1/2 HT-MCS 0-15 =3/4/56 VHT =7/8/9/10/11 */ |
| u8 TxPwrByRateTable; |
| u8 TxPwrByRateBand; |
| s8 TxPwrByRateOffset[TX_PWR_BY_RATE_NUM_BAND] |
| [TX_PWR_BY_RATE_NUM_RF] |
| [TX_PWR_BY_RATE_NUM_RF] |
| [TX_PWR_BY_RATE_NUM_RATE]; |
| /* */ |
| |
| /* 2 Power Limit Table */ |
| u8 TxPwrLevelCck[RF_PATH_MAX_92C_88E][CHANNEL_MAX_NUMBER]; |
| u8 TxPwrLevelHT40_1S[RF_PATH_MAX_92C_88E][CHANNEL_MAX_NUMBER]; /* For HT 40MHZ pwr */ |
| u8 TxPwrLevelHT40_2S[RF_PATH_MAX_92C_88E][CHANNEL_MAX_NUMBER]; /* For HT 40MHZ pwr */ |
| s8 TxPwrHt20Diff[RF_PATH_MAX_92C_88E][CHANNEL_MAX_NUMBER];/* HT 20<->40 Pwr diff */ |
| u8 TxPwrLegacyHtDiff[RF_PATH_MAX_92C_88E][CHANNEL_MAX_NUMBER];/* For HT<->legacy pwr diff */ |
| |
| /* Power Limit Table for 2.4G */ |
| s8 TxPwrLimit_2_4G[MAX_REGULATION_NUM] |
| [MAX_2_4G_BANDWITH_NUM] |
| [MAX_RATE_SECTION_NUM] |
| [CHANNEL_MAX_NUMBER_2G] |
| [MAX_RF_PATH_NUM]; |
| |
| /* Power Limit Table for 5G */ |
| s8 TxPwrLimit_5G[MAX_REGULATION_NUM] |
| [MAX_5G_BANDWITH_NUM] |
| [MAX_RATE_SECTION_NUM] |
| [CHANNEL_MAX_NUMBER_5G] |
| [MAX_RF_PATH_NUM]; |
| |
| |
| /* Store the original power by rate value of the base of each rate section of rf path A & B */ |
| u8 TxPwrByRateBase2_4G[TX_PWR_BY_RATE_NUM_RF] |
| [TX_PWR_BY_RATE_NUM_RF] |
| [MAX_BASE_NUM_IN_PHY_REG_PG_2_4G]; |
| u8 TxPwrByRateBase5G[TX_PWR_BY_RATE_NUM_RF] |
| [TX_PWR_BY_RATE_NUM_RF] |
| [MAX_BASE_NUM_IN_PHY_REG_PG_5G]; |
| |
| /* For power group */ |
| u8 PwrGroupHT20[RF_PATH_MAX_92C_88E][CHANNEL_MAX_NUMBER]; |
| u8 PwrGroupHT40[RF_PATH_MAX_92C_88E][CHANNEL_MAX_NUMBER]; |
| |
| |
| |
| |
| u8 PGMaxGroup; |
| u8 LegacyHTTxPowerDiff;/* Legacy to HT rate power diff */ |
| /* The current Tx Power Level */ |
| u8 CurrentCckTxPwrIdx; |
| u8 CurrentOfdm24GTxPwrIdx; |
| u8 CurrentBW2024GTxPwrIdx; |
| u8 CurrentBW4024GTxPwrIdx; |
| |
| /* Read/write are allow for following hardware information variables */ |
| u8 pwrGroupCnt; |
| u32 MCSTxPowerLevelOriginalOffset[MAX_PG_GROUP][16]; |
| u32 CCKTxPowerLevelOriginalOffset; |
| |
| u8 CrystalCap; |
| u32 AntennaTxPath; /* Antenna path Tx */ |
| u32 AntennaRxPath; /* Antenna path Rx */ |
| |
| u8 PAType_2G; |
| u8 PAType_5G; |
| u8 LNAType_2G; |
| u8 LNAType_5G; |
| u8 ExternalPA_2G; |
| u8 ExternalLNA_2G; |
| u8 ExternalPA_5G; |
| u8 ExternalLNA_5G; |
| u8 TypeGLNA; |
| u8 TypeGPA; |
| u8 TypeALNA; |
| u8 TypeAPA; |
| u8 RFEType; |
| u8 BoardType; |
| u8 ExternalPA; |
| u8 bIQKInitialized; |
| bool bLCKInProgress; |
| |
| bool bSwChnl; |
| bool bSetChnlBW; |
| bool bChnlBWInitialized; |
| bool bNeedIQK; |
| |
| u8 bLedOpenDrain; /* Support Open-drain arrangement for controlling the LED. Added by Roger, 2009.10.16. */ |
| u8 TxPowerTrackControl; /* for mp mode, turn off txpwrtracking as default */ |
| u8 b1x1RecvCombine; /* for 1T1R receive combining */ |
| |
| u32 AcParam_BE; /* Original parameter for BE, use for EDCA turbo. */ |
| |
| struct bb_register_def PHYRegDef[4]; /* Radio A/B/C/D */ |
| |
| u32 RfRegChnlVal[2]; |
| |
| /* RDG enable */ |
| bool bRDGEnable; |
| |
| /* for host message to fw */ |
| u8 LastHMEBoxNum; |
| |
| u8 fw_ractrl; |
| u8 RegTxPause; |
| /* Beacon function related global variable. */ |
| u8 RegBcnCtrlVal; |
| u8 RegFwHwTxQCtrl; |
| u8 RegReg542; |
| u8 RegCR_1; |
| u8 Reg837; |
| u8 RegRFPathS1; |
| u16 RegRRSR; |
| |
| u8 CurAntenna; |
| u8 AntDivCfg; |
| u8 AntDetection; |
| u8 TRxAntDivType; |
| u8 ant_path; /* for 8723B s0/s1 selection */ |
| |
| u8 u1ForcedIgiLb; /* forced IGI lower bound */ |
| |
| u8 bDumpRxPkt;/* for debug */ |
| u8 bDumpTxPkt;/* for debug */ |
| u8 FwRsvdPageStartOffset; /* 2010.06.23. Added by tynli. Reserve page start offset except beacon in TxQ. */ |
| |
| /* 2010/08/09 MH Add CU power down mode. */ |
| bool pwrdown; |
| |
| /* Add for dual MAC 0--Mac0 1--Mac1 */ |
| u32 interfaceIndex; |
| |
| u8 OutEpQueueSel; |
| u8 OutEpNumber; |
| |
| /* 2010/12/10 MH Add for USB aggreation mode dynamic shceme. */ |
| bool UsbRxHighSpeedMode; |
| |
| /* 2010/11/22 MH Add for slim combo debug mode selective. */ |
| /* This is used for fix the drawback of CU TSMC-A/UMC-A cut. HW auto suspend ability. Close BT clock. */ |
| bool SlimComboDbg; |
| |
| /* u8 AMPDUDensity; */ |
| |
| /* Auto FSM to Turn On, include clock, isolation, power control for MAC only */ |
| u8 bMacPwrCtrlOn; |
| |
| u8 RegIQKFWOffload; |
| struct submit_ctx iqk_sctx; |
| |
| enum RT_AMPDU_BURST AMPDUBurstMode; /* 92C maybe not use, but for compile successfully */ |
| |
| u32 sdio_himr; |
| u32 sdio_hisr; |
| |
| /* SDIO Tx FIFO related. */ |
| /* HIQ, MID, LOW, PUB free pages; padapter->xmitpriv.free_txpg */ |
| u8 SdioTxFIFOFreePage[SDIO_TX_FREE_PG_QUEUE]; |
| _lock SdioTxFIFOFreePageLock; |
| u8 SdioTxOQTMaxFreeSpace; |
| u8 SdioTxOQTFreeSpace; |
| |
| |
| /* SDIO Rx FIFO related. */ |
| u8 SdioRxFIFOCnt; |
| u16 SdioRxFIFOSize; |
| |
| u32 sdio_tx_max_len[SDIO_MAX_TX_QUEUE];/* H, N, L, used for sdio tx aggregation max length per queue */ |
| |
| struct dm_priv dmpriv; |
| DM_ODM_T odmpriv; |
| |
| /* For bluetooth co-existance */ |
| BT_COEXIST bt_coexist; |
| |
| /* Interrupt related register information. */ |
| u32 SysIntrStatus; |
| u32 SysIntrMask; |
| |
| |
| char para_file_buf[MAX_PARA_FILE_BUF_LEN]; |
| char *mac_reg; |
| u32 mac_reg_len; |
| char *bb_phy_reg; |
| u32 bb_phy_reg_len; |
| char *bb_agc_tab; |
| u32 bb_agc_tab_len; |
| char *bb_phy_reg_pg; |
| u32 bb_phy_reg_pg_len; |
| char *bb_phy_reg_mp; |
| u32 bb_phy_reg_mp_len; |
| char *rf_radio_a; |
| u32 rf_radio_a_len; |
| char *rf_radio_b; |
| u32 rf_radio_b_len; |
| char *rf_tx_pwr_track; |
| u32 rf_tx_pwr_track_len; |
| char *rf_tx_pwr_lmt; |
| u32 rf_tx_pwr_lmt_len; |
| |
| #ifdef CONFIG_BACKGROUND_NOISE_MONITOR |
| s16 noise[ODM_MAX_CHANNEL_NUM]; |
| #endif |
| |
| }; |
| |
| #define GET_HAL_DATA(__padapter) ((struct hal_com_data *)((__padapter)->HalData)) |
| #define GET_HAL_RFPATH_NUM(__padapter) (((struct hal_com_data *)((__padapter)->HalData))->NumTotalRFPath) |
| #define RT_GetInterfaceSelection(_Adapter) (GET_HAL_DATA(_Adapter)->InterfaceSel) |
| #define GET_RF_TYPE(__padapter) (GET_HAL_DATA(__padapter)->rf_type) |
| |
| #endif /* __HAL_DATA_H__ */ |
