| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/rv1108-cru.h> |
| #include <dt-bindings/pinctrl/rockchip.h> |
| #include <dt-bindings/thermal/thermal.h> |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| compatible = "rockchip,rv1108"; |
| |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| i2c3 = &i2c3; |
| serial0 = &uart0; |
| serial1 = &uart1; |
| serial2 = &uart2; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@f00 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0xf00>; |
| clock-latency = <40000>; |
| clocks = <&cru ARMCLK>; |
| #cooling-cells = <2>; /* min followed by max */ |
| dynamic-power-coefficient = <75>; |
| operating-points-v2 = <&cpu_opp_table>; |
| }; |
| }; |
| |
| cpu_opp_table: opp_table { |
| compatible = "operating-points-v2"; |
| |
| opp-408000000 { |
| opp-hz = /bits/ 64 <408000000>; |
| opp-microvolt = <975000>; |
| clock-latency-ns = <40000>; |
| }; |
| opp-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <975000>; |
| clock-latency-ns = <40000>; |
| }; |
| opp-816000000 { |
| opp-hz = /bits/ 64 <816000000>; |
| opp-microvolt = <1025000>; |
| clock-latency-ns = <40000>; |
| }; |
| opp-1008000000 { |
| opp-hz = /bits/ 64 <1008000000>; |
| opp-microvolt = <1150000>; |
| clock-latency-ns = <40000>; |
| }; |
| }; |
| |
| arm-pmu { |
| compatible = "arm,cortex-a7-pmu"; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>; |
| arm,cpu-registers-not-fw-configured; |
| clock-frequency = <24000000>; |
| }; |
| |
| xin24m: oscillator { |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| clock-output-names = "xin24m"; |
| #clock-cells = <0>; |
| }; |
| |
| amba { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| pdma: pdma@102a0000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0x102a0000 0x4000>; |
| interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| arm,pl330-broken-no-flushp; |
| clocks = <&cru ACLK_DMAC>; |
| clock-names = "apb_pclk"; |
| }; |
| }; |
| |
| bus_intmem@10080000 { |
| compatible = "mmio-sram"; |
| reg = <0x10080000 0x2000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x10080000 0x2000>; |
| }; |
| |
| uart2: serial@10210000 { |
| compatible = "rockchip,rv1108-uart", "snps,dw-apb-uart"; |
| reg = <0x10210000 0x100>; |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&pdma 6>, <&pdma 7>; |
| #dma-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2m0_xfer>; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@10220000 { |
| compatible = "rockchip,rv1108-uart", "snps,dw-apb-uart"; |
| reg = <0x10220000 0x100>; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&pdma 4>, <&pdma 5>; |
| #dma-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1_xfer>; |
| status = "disabled"; |
| }; |
| |
| uart0: serial@10230000 { |
| compatible = "rockchip,rv1108-uart", "snps,dw-apb-uart"; |
| reg = <0x10230000 0x100>; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&pdma 2>, <&pdma 3>; |
| #dma-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@10240000 { |
| compatible = "rockchip,rv1108-i2c"; |
| reg = <0x10240000 0x1000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&cru SCLK_I2C1>, <&cru PCLK_I2C1>; |
| clock-names = "i2c", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_xfer>; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@10250000 { |
| compatible = "rockchip,rv1108-i2c"; |
| reg = <0x10250000 0x1000>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&cru SCLK_I2C2>, <&cru PCLK_I2C2>; |
| clock-names = "i2c", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2m1_xfer>; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@10260000 { |
| compatible = "rockchip,rv1108-i2c"; |
| reg = <0x10260000 0x1000>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&cru SCLK_I2C3>, <&cru PCLK_I2C3>; |
| clock-names = "i2c", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c3_xfer>; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| }; |
| |
| spi: spi@10270000 { |
| compatible = "rockchip,rv1108-spi"; |
| reg = <0x10270000 0x1000>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_SPI>, <&cru PCLK_SPI>; |
| clock-names = "spiclk", "apb_pclk"; |
| dmas = <&pdma 8>, <&pdma 9>; |
| dma-names = "tx", "rx"; |
| #dma-cells = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| pwm4: pwm@10280000 { |
| compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm"; |
| reg = <0x10280000 0x10>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_PWM>, <&cru PCLK_PWM>; |
| clock-names = "pwm", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm4_pin>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm5: pwm@10280010 { |
| compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm"; |
| reg = <0x10280010 0x10>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_PWM>, <&cru PCLK_PWM>; |
| clock-names = "pwm", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm5_pin>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm6: pwm@10280020 { |
| compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm"; |
| reg = <0x10280020 0x10>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_PWM>, <&cru PCLK_PWM>; |
| clock-names = "pwm", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm6_pin>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm7: pwm@10280030 { |
| compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm"; |
| reg = <0x10280030 0x10>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_PWM>, <&cru PCLK_PWM>; |
| clock-names = "pwm", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm7_pin>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| grf: syscon@10300000 { |
| compatible = "rockchip,rv1108-grf", "syscon", "simple-mfd"; |
| reg = <0x10300000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| u2phy: usb2-phy@100 { |
| compatible = "rockchip,rv1108-usb2phy"; |
| reg = <0x100 0x0c>; |
| clocks = <&cru SCLK_USBPHY>; |
| clock-names = "phyclk"; |
| #clock-cells = <0>; |
| clock-output-names = "usbphy"; |
| rockchip,usbgrf = <&usbgrf>; |
| status = "disabled"; |
| |
| u2phy_otg: otg-port { |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "otg-mux"; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| u2phy_host: host-port { |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "linestate"; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| timer: timer@10350000 { |
| compatible = "rockchip,rv1108-timer", "rockchip,rk3288-timer"; |
| reg = <0x10350000 0x20>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&xin24m>, <&cru PCLK_TIMER>; |
| clock-names = "timer", "pclk"; |
| }; |
| |
| watchdog: wdt@10360000 { |
| compatible = "snps,dw-wdt"; |
| reg = <0x10360000 0x100>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_WDT>; |
| clock-names = "pclk_wdt"; |
| status = "disabled"; |
| }; |
| |
| thermal-zones { |
| soc_thermal: soc-thermal { |
| polling-delay-passive = <20>; |
| polling-delay = <1000>; |
| sustainable-power = <50>; |
| thermal-sensors = <&tsadc 0>; |
| |
| trips { |
| threshold: trip-point0 { |
| temperature = <70000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| target: trip-point1 { |
| temperature = <85000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| soc_crit: soc-crit { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&target>; |
| cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| contribution = <4096>; |
| }; |
| }; |
| }; |
| }; |
| |
| tsadc: tsadc@10370000 { |
| compatible = "rockchip,rv1108-tsadc"; |
| reg = <0x10370000 0x100>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| assigned-clocks = <&cru SCLK_TSADC>; |
| assigned-clock-rates = <750000>; |
| clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; |
| clock-names = "tsadc", "apb_pclk"; |
| pinctrl-names = "init", "default", "sleep"; |
| pinctrl-0 = <&otp_gpio>; |
| pinctrl-1 = <&otp_out>; |
| pinctrl-2 = <&otp_gpio>; |
| resets = <&cru SRST_TSADC>; |
| reset-names = "tsadc-apb"; |
| rockchip,hw-tshut-temp = <120000>; |
| #thermal-sensor-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| adc: adc@1038c000 { |
| compatible = "rockchip,rv1108-saradc", "rockchip,rk3399-saradc"; |
| reg = <0x1038c000 0x100>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| #io-channel-cells = <1>; |
| clock-frequency = <1000000>; |
| clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; |
| clock-names = "saradc", "apb_pclk"; |
| status = "disabled"; |
| }; |
| |
| i2c0: i2c@20000000 { |
| compatible = "rockchip,rv1108-i2c"; |
| reg = <0x20000000 0x1000>; |
| interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&cru SCLK_I2C0_PMU>, <&cru PCLK_I2C0_PMU>; |
| clock-names = "i2c", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c0_xfer>; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| }; |
| |
| pwm0: pwm@20040000 { |
| compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm"; |
| reg = <0x20040000 0x10>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_PWM0_PMU>, <&cru PCLK_PWM0_PMU>; |
| clock-names = "pwm", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm0_pin>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm1: pwm@20040010 { |
| compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm"; |
| reg = <0x20040010 0x10>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_PWM0_PMU>, <&cru PCLK_PWM0_PMU>; |
| clock-names = "pwm", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm1_pin>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm2: pwm@20040020 { |
| compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm"; |
| reg = <0x20040020 0x10>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_PWM0_PMU>, <&cru PCLK_PWM0_PMU>; |
| clock-names = "pwm", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm2_pin>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm3: pwm@20040030 { |
| compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm"; |
| reg = <0x20040030 0x10>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_PWM0_PMU>, <&cru PCLK_PWM0_PMU>; |
| clock-names = "pwm", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm3_pin>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pmugrf: syscon@20060000 { |
| compatible = "rockchip,rv1108-pmugrf", "syscon"; |
| reg = <0x20060000 0x1000>; |
| }; |
| |
| usbgrf: syscon@202a0000 { |
| compatible = "rockchip,rv1108-usbgrf", "syscon"; |
| reg = <0x202a0000 0x1000>; |
| }; |
| |
| cru: clock-controller@20200000 { |
| compatible = "rockchip,rv1108-cru"; |
| reg = <0x20200000 0x1000>; |
| rockchip,grf = <&grf>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| emmc: dwmmc@30110000 { |
| compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc"; |
| reg = <0x30110000 0x4000>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>, |
| <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| max-frequency = <150000000>; |
| status = "disabled"; |
| }; |
| |
| sdio: dwmmc@30120000 { |
| compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc"; |
| reg = <0x30120000 0x4000>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>, |
| <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| max-frequency = <150000000>; |
| status = "disabled"; |
| }; |
| |
| sdmmc: dwmmc@30130000 { |
| compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc"; |
| reg = <0x30130000 0x4000>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>, |
| <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| max-frequency = <100000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; |
| status = "disabled"; |
| }; |
| |
| usb_host_ehci: usb@30140000 { |
| compatible = "generic-ehci"; |
| reg = <0x30140000 0x20000>; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_HOST0>, <&u2phy>; |
| clock-names = "usbhost", "utmi"; |
| phys = <&u2phy_host>; |
| phy-names = "usb"; |
| status = "disabled"; |
| }; |
| |
| usb_host_ohci: usb@30160000 { |
| compatible = "generic-ohci"; |
| reg = <0x30160000 0x20000>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_HOST0>, <&u2phy>; |
| clock-names = "usbhost", "utmi"; |
| phys = <&u2phy_host>; |
| phy-names = "usb"; |
| status = "disabled"; |
| }; |
| |
| usb_otg: usb@30180000 { |
| compatible = "rockchip,rv1108-usb", "rockchip,rk3066-usb", |
| "snps,dwc2"; |
| reg = <0x30180000 0x40000>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_OTG>; |
| clock-names = "otg"; |
| dr_mode = "otg"; |
| g-np-tx-fifo-size = <16>; |
| g-rx-fifo-size = <280>; |
| g-tx-fifo-size = <256 128 128 64 32 16>; |
| g-use-dma; |
| phys = <&u2phy_otg>; |
| phy-names = "usb2-phy"; |
| status = "disabled"; |
| }; |
| |
| gmac: eth@30200000 { |
| compatible = "rockchip,rv1108-gmac"; |
| reg = <0x30200000 0x10000>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq", "eth_wake_irq"; |
| clocks = <&cru SCLK_MAC>, |
| <&cru SCLK_MAC_RX>, <&cru SCLK_MAC_RX>, |
| <&cru SCLK_MAC_REF>, <&cru SCLK_MAC_REFOUT>, |
| <&cru ACLK_GMAC>, <&cru PCLK_GMAC>; |
| clock-names = "stmmaceth", |
| "mac_clk_rx", "mac_clk_tx", |
| "clk_mac_ref", "clk_mac_refout", |
| "aclk_mac", "pclk_mac"; |
| /* rv1108 only supports an rmii interface */ |
| phy-mode = "rmii"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&rmii_pins>; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| }; |
| |
| gic: interrupt-controller@32010000 { |
| compatible = "arm,gic-400"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| #address-cells = <0>; |
| |
| reg = <0x32011000 0x1000>, |
| <0x32012000 0x2000>, |
| <0x32014000 0x2000>, |
| <0x32016000 0x2000>; |
| interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| pinctrl: pinctrl { |
| compatible = "rockchip,rv1108-pinctrl"; |
| rockchip,grf = <&grf>; |
| rockchip,pmu = <&pmugrf>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio0: gpio0@20030000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x20030000 0x100>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO0_PMU>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio1: gpio1@10310000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x10310000 0x100>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO1>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio2@10320000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x10320000 0x100>; |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO2>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio3@10330000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x10330000 0x100>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO3>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pcfg_pull_up: pcfg-pull-up { |
| bias-pull-up; |
| }; |
| |
| pcfg_pull_down: pcfg-pull-down { |
| bias-pull-down; |
| }; |
| |
| pcfg_pull_none: pcfg-pull-none { |
| bias-disable; |
| }; |
| |
| pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma { |
| drive-strength = <8>; |
| }; |
| |
| pcfg_pull_none_drv_12ma: pcfg-pull-none-drv-12ma { |
| drive-strength = <12>; |
| }; |
| |
| pcfg_pull_none_smt: pcfg-pull-none-smt { |
| bias-disable; |
| input-schmitt-enable; |
| }; |
| |
| pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma { |
| bias-pull-up; |
| drive-strength = <8>; |
| }; |
| |
| pcfg_pull_none_drv_4ma: pcfg-pull-none-drv-4ma { |
| drive-strength = <4>; |
| }; |
| |
| pcfg_pull_up_drv_4ma: pcfg-pull-up-drv-4ma { |
| bias-pull-up; |
| drive-strength = <4>; |
| }; |
| |
| pcfg_output_high: pcfg-output-high { |
| output-high; |
| }; |
| |
| pcfg_output_low: pcfg-output-low { |
| output-low; |
| }; |
| |
| pcfg_input_high: pcfg-input-high { |
| bias-pull-up; |
| input-enable; |
| }; |
| |
| emmc { |
| emmc_bus8: emmc-bus8 { |
| rockchip,pins = <2 RK_PA0 2 &pcfg_pull_up_drv_8ma>, |
| <2 RK_PA1 2 &pcfg_pull_up_drv_8ma>, |
| <2 RK_PA2 2 &pcfg_pull_up_drv_8ma>, |
| <2 RK_PA3 2 &pcfg_pull_up_drv_8ma>, |
| <2 RK_PA4 2 &pcfg_pull_up_drv_8ma>, |
| <2 RK_PA5 2 &pcfg_pull_up_drv_8ma>, |
| <2 RK_PA6 2 &pcfg_pull_up_drv_8ma>, |
| <2 RK_PA7 2 &pcfg_pull_up_drv_8ma>; |
| }; |
| |
| emmc_clk: emmc-clk { |
| rockchip,pins = <2 RK_PB6 1 &pcfg_pull_none_drv_8ma>; |
| }; |
| |
| emmc_cmd: emmc-cmd { |
| rockchip,pins = <2 RK_PB4 2 &pcfg_pull_up_drv_8ma>; |
| }; |
| }; |
| |
| gmac { |
| rmii_pins: rmii-pins { |
| rockchip,pins = <1 RK_PC5 2 &pcfg_pull_none>, |
| <1 RK_PC3 2 &pcfg_pull_none>, |
| <1 RK_PC4 2 &pcfg_pull_none>, |
| <1 RK_PB2 3 &pcfg_pull_none_drv_12ma>, |
| <1 RK_PB3 3 &pcfg_pull_none_drv_12ma>, |
| <1 RK_PB4 3 &pcfg_pull_none_drv_12ma>, |
| <1 RK_PB5 3 &pcfg_pull_none>, |
| <1 RK_PB6 3 &pcfg_pull_none>, |
| <1 RK_PB7 3 &pcfg_pull_none>, |
| <1 RK_PC2 3 &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c0 { |
| i2c0_xfer: i2c0-xfer { |
| rockchip,pins = <0 RK_PB1 1 &pcfg_pull_none_smt>, |
| <0 RK_PB2 1 &pcfg_pull_none_smt>; |
| }; |
| }; |
| |
| i2c1 { |
| i2c1_xfer: i2c1-xfer { |
| rockchip,pins = <2 RK_PD3 1 &pcfg_pull_up>, |
| <2 RK_PD4 1 &pcfg_pull_up>; |
| }; |
| }; |
| |
| i2c2m1 { |
| i2c2m1_xfer: i2c2m1-xfer { |
| rockchip,pins = <0 RK_PC2 2 &pcfg_pull_none>, |
| <0 RK_PC6 3 &pcfg_pull_none>; |
| }; |
| |
| i2c2m1_gpio: i2c2m1-gpio { |
| rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>, |
| <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c2m05v { |
| i2c2m05v_xfer: i2c2m05v-xfer { |
| rockchip,pins = <1 RK_PD5 2 &pcfg_pull_none>, |
| <1 RK_PD4 2 &pcfg_pull_none>; |
| }; |
| |
| i2c2m05v_gpio: i2c2m05v-gpio { |
| rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>, |
| <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c3 { |
| i2c3_xfer: i2c3-xfer { |
| rockchip,pins = <0 RK_PB6 1 &pcfg_pull_none>, |
| <0 RK_PC4 2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm0 { |
| pwm0_pin: pwm0-pin { |
| rockchip,pins = <0 RK_PC5 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm1 { |
| pwm1_pin: pwm1-pin { |
| rockchip,pins = <0 RK_PC4 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm2 { |
| pwm2_pin: pwm2-pin { |
| rockchip,pins = <0 RK_PC6 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm3 { |
| pwm3_pin: pwm3-pin { |
| rockchip,pins = <0 RK_PC0 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm4 { |
| pwm4_pin: pwm4-pin { |
| rockchip,pins = <1 RK_PC1 3 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm5 { |
| pwm5_pin: pwm5-pin { |
| rockchip,pins = <1 RK_PA7 2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm6 { |
| pwm6_pin: pwm6-pin { |
| rockchip,pins = <1 RK_PB0 2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm7 { |
| pwm7_pin: pwm7-pin { |
| rockchip,pins = <1 RK_PB1 2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| sdmmc { |
| sdmmc_clk: sdmmc-clk { |
| rockchip,pins = <3 RK_PC4 1 &pcfg_pull_none_drv_4ma>; |
| }; |
| |
| sdmmc_cmd: sdmmc-cmd { |
| rockchip,pins = <3 RK_PC5 1 &pcfg_pull_up_drv_4ma>; |
| }; |
| |
| sdmmc_cd: sdmmc-cd { |
| rockchip,pins = <0 RK_PA1 1 &pcfg_pull_up_drv_4ma>; |
| }; |
| |
| sdmmc_bus1: sdmmc-bus1 { |
| rockchip,pins = <3 RK_PC3 1 &pcfg_pull_up_drv_4ma>; |
| }; |
| |
| sdmmc_bus4: sdmmc-bus4 { |
| rockchip,pins = <3 RK_PC3 1 &pcfg_pull_up_drv_4ma>, |
| <3 RK_PC2 1 &pcfg_pull_up_drv_4ma>, |
| <3 RK_PC1 1 &pcfg_pull_up_drv_4ma>, |
| <3 RK_PC0 1 &pcfg_pull_up_drv_4ma>; |
| }; |
| }; |
| |
| spim0 { |
| spim0_clk: spim0-clk { |
| rockchip,pins = <1 RK_PD0 2 &pcfg_pull_up>; |
| }; |
| |
| spim0_cs0: spim0-cs0 { |
| rockchip,pins = <1 RK_PD1 2 &pcfg_pull_up>; |
| }; |
| |
| spim0_tx: spim0-tx { |
| rockchip,pins = <1 RK_PD3 2 &pcfg_pull_up>; |
| }; |
| |
| spim0_rx: spim0-rx { |
| rockchip,pins = <1 RK_PD2 2 &pcfg_pull_up>; |
| }; |
| }; |
| |
| spim1 { |
| spim1_clk: spim1-clk { |
| rockchip,pins = <0 RK_PA3 1 &pcfg_pull_up>; |
| }; |
| |
| spim1_cs0: spim1-cs0 { |
| rockchip,pins = <0 RK_PA4 1 &pcfg_pull_up>; |
| }; |
| |
| spim1_rx: spim1-rx { |
| rockchip,pins = <0 RK_PB0 1 &pcfg_pull_up>; |
| }; |
| |
| spim1_tx: spim1-tx { |
| rockchip,pins = <0 RK_PA7 1 &pcfg_pull_up>; |
| }; |
| }; |
| |
| tsadc { |
| otp_out: otp-out { |
| rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>; |
| }; |
| |
| otp_gpio: otp-gpio { |
| rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart0 { |
| uart0_xfer: uart0-xfer { |
| rockchip,pins = <3 RK_PA6 1 &pcfg_pull_up>, |
| <3 RK_PA5 1 &pcfg_pull_none>; |
| }; |
| |
| uart0_cts: uart0-cts { |
| rockchip,pins = <3 RK_PA4 1 &pcfg_pull_none>; |
| }; |
| |
| uart0_rts: uart0-rts { |
| rockchip,pins = <3 RK_PA3 1 &pcfg_pull_none>; |
| }; |
| |
| uart0_rts_gpio: uart0-rts-gpio { |
| rockchip,pins = <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart1 { |
| uart1_xfer: uart1-xfer { |
| rockchip,pins = <1 RK_PD3 1 &pcfg_pull_up>, |
| <1 RK_PD2 1 &pcfg_pull_none>; |
| }; |
| |
| uart1_cts: uart1-cts { |
| rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>; |
| }; |
| |
| uart1_rts: uart1-rts { |
| rockchip,pins = <1 RK_PD1 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart2m0 { |
| uart2m0_xfer: uart2m0-xfer { |
| rockchip,pins = <2 RK_PD2 1 &pcfg_pull_up>, |
| <2 RK_PD1 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart2m1 { |
| uart2m1_xfer: uart2m1-xfer { |
| rockchip,pins = <3 RK_PC3 2 &pcfg_pull_up>, |
| <3 RK_PC2 2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart2_5v { |
| uart2_5v_cts: uart2_5v-cts { |
| rockchip,pins = <1 RK_PD4 1 &pcfg_pull_none>; |
| }; |
| |
| uart2_5v_rts: uart2_5v-rts { |
| rockchip,pins = <1 RK_PD5 1 &pcfg_pull_none>; |
| }; |
| }; |
| }; |
| }; |