| # | |
| # Physical Layer USB driver configuration | |
| # | |
| menu "USB Physical Layer drivers" | |
| config USB_PHY | |
| select EXTCON | |
| def_bool n | |
| # | |
| # USB Transceiver Drivers | |
| # | |
| config AB8500_USB | |
| tristate "AB8500 USB Transceiver Driver" | |
| depends on AB8500_CORE | |
| select USB_PHY | |
| help | |
| Enable this to support the USB OTG transceiver in AB8500 chip. | |
| This transceiver supports high and full speed devices plus, | |
| in host mode, low speed. | |
| config FSL_USB2_OTG | |
| bool "Freescale USB OTG Transceiver Driver" | |
| depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM | |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' | |
| select USB_PHY | |
| help | |
| Enable this to support Freescale USB OTG transceiver. | |
| config ISP1301_OMAP | |
| tristate "Philips ISP1301 with OMAP OTG" | |
| depends on I2C && ARCH_OMAP_OTG | |
| depends on USB | |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' | |
| select USB_PHY | |
| help | |
| If you say yes here you get support for the Philips ISP1301 | |
| USB-On-The-Go transceiver working with the OMAP OTG controller. | |
| The ISP1301 is a full speed USB transceiver which is used in | |
| products including H2, H3, and H4 development boards for Texas | |
| Instruments OMAP processors. | |
| This driver can also be built as a module. If so, the module | |
| will be called phy-isp1301-omap. | |
| config KEYSTONE_USB_PHY | |
| tristate "Keystone USB PHY Driver" | |
| depends on ARCH_KEYSTONE || COMPILE_TEST | |
| depends on NOP_USB_XCEIV | |
| help | |
| Enable this to support Keystone USB phy. This driver provides | |
| interface to interact with USB 2.0 and USB 3.0 PHY that is part | |
| of the Keystone SOC. | |
| config NOP_USB_XCEIV | |
| tristate "NOP USB Transceiver Driver" | |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in | |
| select USB_PHY | |
| help | |
| This driver is to be used by all the usb transceiver which are either | |
| built-in with usb ip or which are autonomous and doesn't require any | |
| phy programming such as ISP1x04 etc. | |
| config AM335X_CONTROL_USB | |
| tristate | |
| config AM335X_PHY_USB | |
| tristate "AM335x USB PHY Driver" | |
| depends on ARM || COMPILE_TEST | |
| depends on NOP_USB_XCEIV | |
| select USB_PHY | |
| select AM335X_CONTROL_USB | |
| select USB_COMMON | |
| help | |
| This driver provides PHY support for that phy which part for the | |
| AM335x SoC. | |
| config TWL6030_USB | |
| tristate "TWL6030 USB Transceiver Driver" | |
| depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS | |
| depends on OF | |
| help | |
| Enable this to support the USB OTG transceiver on TWL6030 | |
| family chips. This TWL6030 transceiver has the VBUS and ID GND | |
| and OTG SRP events capabilities. For all other transceiver functionality | |
| UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs | |
| are hooked to this driver through platform_data structure. | |
| The definition of internal PHY APIs are in the mach-omap2 layer. | |
| config USB_GPIO_VBUS | |
| tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" | |
| depends on GPIOLIB || COMPILE_TEST | |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' | |
| select USB_PHY | |
| help | |
| Provides simple GPIO VBUS sensing for controllers with an | |
| internal transceiver via the usb_phy interface, and | |
| optionally control of a D+ pullup GPIO as well as a VBUS | |
| current limit regulator. | |
| config OMAP_OTG | |
| tristate "OMAP USB OTG controller driver" | |
| depends on ARCH_OMAP_OTG && EXTCON | |
| help | |
| Enable this to support some transceivers on OMAP1 platforms. OTG | |
| controller is needed to switch between host and peripheral modes. | |
| This driver can also be built as a module. If so, the module | |
| will be called phy-omap-otg. | |
| config TAHVO_USB | |
| tristate "Tahvo USB transceiver driver" | |
| depends on MFD_RETU | |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' | |
| select USB_PHY | |
| help | |
| Enable this to support USB transceiver on Tahvo. This is used | |
| at least on Nokia 770. | |
| config TAHVO_USB_HOST_BY_DEFAULT | |
| depends on TAHVO_USB | |
| bool "Device in USB host mode by default" | |
| help | |
| Say Y here, if you want the device to enter USB host mode | |
| by default on bootup. | |
| config USB_ISP1301 | |
| tristate "NXP ISP1301 USB transceiver support" | |
| depends on USB || USB_GADGET | |
| depends on I2C | |
| select USB_PHY | |
| help | |
| Say Y here to add support for the NXP ISP1301 USB transceiver driver. | |
| This chip is typically used as USB transceiver for USB host, gadget | |
| and OTG drivers (to be selected separately). | |
| To compile this driver as a module, choose M here: the | |
| module will be called phy-isp1301. | |
| config USB_MV_OTG | |
| tristate "Marvell USB OTG support" | |
| depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG | |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' | |
| select USB_PHY | |
| help | |
| Say Y here if you want to build Marvell USB OTG transciever | |
| driver in kernel (including PXA and MMP series). This driver | |
| implements role switch between EHCI host driver and gadget driver. | |
| To compile this driver as a module, choose M here. | |
| config USB_MXS_PHY | |
| tristate "Freescale MXS USB PHY support" | |
| depends on ARCH_MXC || ARCH_MXS | |
| select STMP_DEVICE | |
| select USB_PHY | |
| help | |
| Enable this to support the Freescale MXS USB PHY. | |
| MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. | |
| config USB_TEGRA_PHY | |
| tristate "NVIDIA Tegra USB PHY Driver" | |
| depends on ARCH_TEGRA | |
| select USB_COMMON | |
| select USB_PHY | |
| select USB_ULPI | |
| help | |
| This driver provides PHY support for the USB controllers found | |
| on NVIDIA Tegra SoC's. | |
| config USB_ULPI | |
| bool "Generic ULPI Transceiver Driver" | |
| depends on ARM || ARM64 | |
| select USB_ULPI_VIEWPORT | |
| help | |
| Enable this to support ULPI connected USB OTG transceivers which | |
| are likely found on embedded boards. | |
| config USB_ULPI_VIEWPORT | |
| bool | |
| help | |
| Provides read/write operations to the ULPI phy register set for | |
| controllers with a viewport register (e.g. Chipidea/ARC controllers). | |
| endmenu |