| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Google Veyron (and derivatives) board device tree source |
| * |
| * Copyright 2015 Google, Inc |
| */ |
| |
| #include <dt-bindings/clock/rockchip,rk808.h> |
| #include <dt-bindings/input/input.h> |
| #include "rk3288.dtsi" |
| |
| / { |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0 0x0 0x80000000>; |
| }; |
| |
| gpio_keys: gpio-keys { |
| compatible = "gpio-keys"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwr_key_l>; |
| power { |
| label = "Power"; |
| gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_POWER>; |
| debounce-interval = <100>; |
| wakeup-source; |
| }; |
| }; |
| |
| gpio-restart { |
| compatible = "gpio-restart"; |
| gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ap_warm_reset_h>; |
| priority = <200>; |
| }; |
| |
| emmc_pwrseq: emmc-pwrseq { |
| compatible = "mmc-pwrseq-emmc"; |
| pinctrl-0 = <&emmc_reset>; |
| pinctrl-names = "default"; |
| reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sdio_pwrseq: sdio-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| clocks = <&rk808 RK808_CLKOUT1>; |
| clock-names = "ext_clock"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_enable_l>, <&wifi_enable_h>; |
| |
| /* |
| * On the module itself this is one of these (depending |
| * on the actual card populated): |
| * - SDIO_RESET_L_WL_REG_ON |
| * - PDN (power down when low) |
| */ |
| reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>; |
| }; |
| |
| vcc_5v: vcc-5v { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_5v"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| vcc33_sys: vcc33-sys { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc33_sys"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| vcc50_hdmi: vcc50-hdmi { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc50_hdmi"; |
| regulator-always-on; |
| regulator-boot-on; |
| vin-supply = <&vcc_5v>; |
| }; |
| }; |
| |
| &cpu0 { |
| cpu0-supply = <&vdd_cpu>; |
| }; |
| |
| /* rk3288-c used in Veyron Chrome-devices has slightly changed OPPs */ |
| &cpu_opp_table { |
| /delete-node/ opp-312000000; |
| |
| opp-1512000000 { |
| opp-microvolt = <1250000>; |
| }; |
| opp-1608000000 { |
| opp-microvolt = <1300000>; |
| }; |
| opp-1704000000 { |
| opp-hz = /bits/ 64 <1704000000>; |
| opp-microvolt = <1350000>; |
| }; |
| opp-1800000000 { |
| opp-hz = /bits/ 64 <1800000000>; |
| opp-microvolt = <1400000>; |
| }; |
| }; |
| |
| &emmc { |
| status = "okay"; |
| |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| rockchip,default-sample-phase = <158>; |
| disable-wp; |
| mmc-hs200-1_8v; |
| mmc-pwrseq = <&emmc_pwrseq>; |
| non-removable; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>; |
| }; |
| |
| &gpu { |
| mali-supply = <&vdd_gpu>; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| ddc-i2c-bus = <&i2c5>; |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| status = "okay"; |
| |
| clock-frequency = <400000>; |
| i2c-scl-falling-time-ns = <50>; /* 2.5ns measured */ |
| i2c-scl-rising-time-ns = <100>; /* 45ns measured */ |
| |
| rk808: pmic@1b { |
| compatible = "rockchip,rk808"; |
| reg = <0x1b>; |
| clock-output-names = "xin32k", "wifibt_32kin"; |
| interrupt-parent = <&gpio0>; |
| interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmic_int_l>; |
| rockchip,system-power-controller; |
| wakeup-source; |
| #clock-cells = <1>; |
| |
| vcc1-supply = <&vcc33_sys>; |
| vcc2-supply = <&vcc33_sys>; |
| vcc3-supply = <&vcc33_sys>; |
| vcc4-supply = <&vcc33_sys>; |
| vcc6-supply = <&vcc_5v>; |
| vcc7-supply = <&vcc33_sys>; |
| vcc8-supply = <&vcc33_sys>; |
| vcc12-supply = <&vcc_18>; |
| vddio-supply = <&vcc33_io>; |
| |
| regulators { |
| vdd_cpu: DCDC_REG1 { |
| regulator-name = "vdd_arm"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-ramp-delay = <6001>; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_gpu: DCDC_REG2 { |
| regulator-name = "vdd_gpu"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1250000>; |
| regulator-ramp-delay = <6001>; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1000000>; |
| }; |
| }; |
| |
| vcc135_ddr: DCDC_REG3 { |
| regulator-name = "vcc135_ddr"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| /* |
| * vcc_18 has several aliases. (vcc18_flashio and |
| * vcc18_wl). We'll add those aliases here just to |
| * make it easier to follow the schematic. The signals |
| * are actually hooked together and only separated for |
| * power measurement purposes). |
| */ |
| vcc18_wl: vcc18_flashio: vcc_18: DCDC_REG4 { |
| regulator-name = "vcc_18"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| /* |
| * Note that both vcc33_io and vcc33_pmuio are always |
| * powered together. To simplify the logic in the dts |
| * we just refer to vcc33_io every time something is |
| * powered from vcc33_pmuio. In fact, on later boards |
| * (such as danger) they're the same net. |
| */ |
| vcc33_io: LDO_REG1 { |
| regulator-name = "vcc33_io"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <3300000>; |
| }; |
| }; |
| |
| vdd_10: LDO_REG3 { |
| regulator-name = "vdd_10"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1000000>; |
| }; |
| }; |
| |
| vdd10_lcd_pwren_h: LDO_REG7 { |
| regulator-name = "vdd10_lcd_pwren_h"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <2500000>; |
| regulator-max-microvolt = <2500000>; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc33_lcd: SWITCH_REG1 { |
| regulator-name = "vcc33_lcd"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| |
| clock-frequency = <400000>; |
| i2c-scl-falling-time-ns = <50>; /* 2.5ns measured */ |
| i2c-scl-rising-time-ns = <100>; /* 40ns measured */ |
| |
| tpm: tpm@20 { |
| compatible = "infineon,slb9645tt"; |
| reg = <0x20>; |
| powered-while-suspended; |
| }; |
| }; |
| |
| &i2c2 { |
| status = "okay"; |
| |
| /* 100kHz since 4.7k resistors don't rise fast enough */ |
| clock-frequency = <100000>; |
| i2c-scl-falling-time-ns = <50>; /* 10ns measured */ |
| i2c-scl-rising-time-ns = <800>; /* 600ns measured */ |
| }; |
| |
| &i2c4 { |
| status = "okay"; |
| |
| clock-frequency = <400000>; |
| i2c-scl-falling-time-ns = <50>; /* 11ns measured */ |
| i2c-scl-rising-time-ns = <300>; /* 225ns measured */ |
| }; |
| |
| &i2c5 { |
| status = "okay"; |
| |
| clock-frequency = <100000>; |
| i2c-scl-falling-time-ns = <300>; |
| i2c-scl-rising-time-ns = <1000>; |
| }; |
| |
| &io_domains { |
| status = "okay"; |
| |
| bb-supply = <&vcc33_io>; |
| dvp-supply = <&vcc_18>; |
| flash0-supply = <&vcc18_flashio>; |
| gpio1830-supply = <&vcc33_io>; |
| gpio30-supply = <&vcc33_io>; |
| lcdc-supply = <&vcc33_lcd>; |
| wifi-supply = <&vcc18_wl>; |
| }; |
| |
| &pwm1 { |
| status = "okay"; |
| }; |
| |
| &sdio0 { |
| status = "okay"; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-sdio-irq; |
| keep-power-in-suspend; |
| mmc-pwrseq = <&sdio_pwrseq>; |
| non-removable; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdio0_clk &sdio0_cmd &sdio0_bus4>; |
| sd-uhs-sdr12; |
| sd-uhs-sdr25; |
| sd-uhs-sdr50; |
| sd-uhs-sdr104; |
| vmmc-supply = <&vcc33_sys>; |
| vqmmc-supply = <&vcc18_wl>; |
| }; |
| |
| &spi2 { |
| status = "okay"; |
| |
| rx-sample-delay-ns = <12>; |
| |
| flash@0 { |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| reg = <0>; |
| }; |
| }; |
| |
| &tsadc { |
| status = "okay"; |
| |
| rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */ |
| rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */ |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| |
| /* We need to go faster than 24MHz, so adjust clock parents / rates */ |
| assigned-clocks = <&cru SCLK_UART0>; |
| assigned-clock-rates = <48000000>; |
| |
| /* Pins don't include flow control by default; add that in */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; |
| }; |
| |
| &uart1 { |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| status = "okay"; |
| }; |
| |
| &usbphy { |
| status = "okay"; |
| }; |
| |
| &usb_host0_ehci { |
| status = "okay"; |
| |
| needs-reset-on-resume; |
| }; |
| |
| &usb_host1 { |
| status = "okay"; |
| }; |
| |
| &usb_otg { |
| status = "okay"; |
| |
| assigned-clocks = <&cru SCLK_USBPHY480M_SRC>; |
| assigned-clock-parents = <&usbphy0>; |
| dr_mode = "host"; |
| }; |
| |
| &vopb { |
| status = "okay"; |
| }; |
| |
| &vopb_mmu { |
| status = "okay"; |
| }; |
| |
| &wdt { |
| status = "okay"; |
| }; |
| |
| &pinctrl { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = < |
| /* Common for sleep and wake, but no owners */ |
| &global_pwroff |
| >; |
| pinctrl-1 = < |
| /* Common for sleep and wake, but no owners */ |
| &global_pwroff |
| >; |
| |
| pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma { |
| bias-disable; |
| drive-strength = <8>; |
| }; |
| |
| pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma { |
| bias-pull-up; |
| drive-strength = <8>; |
| }; |
| |
| pcfg_output_high: pcfg-output-high { |
| output-high; |
| }; |
| |
| pcfg_output_low: pcfg-output-low { |
| output-low; |
| }; |
| |
| buttons { |
| pwr_key_l: pwr-key-l { |
| rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| emmc { |
| emmc_reset: emmc-reset { |
| rockchip,pins = <2 9 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| /* |
| * We run eMMC at max speed; bump up drive strength. |
| * We also have external pulls, so disable the internal ones. |
| */ |
| emmc_clk: emmc-clk { |
| rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none_drv_8ma>; |
| }; |
| |
| emmc_cmd: emmc-cmd { |
| rockchip,pins = <3 16 RK_FUNC_2 &pcfg_pull_none_drv_8ma>; |
| }; |
| |
| emmc_bus8: emmc-bus8 { |
| rockchip,pins = <3 0 RK_FUNC_2 &pcfg_pull_none_drv_8ma>, |
| <3 1 RK_FUNC_2 &pcfg_pull_none_drv_8ma>, |
| <3 2 RK_FUNC_2 &pcfg_pull_none_drv_8ma>, |
| <3 3 RK_FUNC_2 &pcfg_pull_none_drv_8ma>, |
| <3 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>, |
| <3 5 RK_FUNC_2 &pcfg_pull_none_drv_8ma>, |
| <3 6 RK_FUNC_2 &pcfg_pull_none_drv_8ma>, |
| <3 7 RK_FUNC_2 &pcfg_pull_none_drv_8ma>; |
| }; |
| }; |
| |
| pmic { |
| pmic_int_l: pmic-int-l { |
| rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| reboot { |
| ap_warm_reset_h: ap-warm-reset-h { |
| rockchip,pins = <RK_GPIO0 13 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| recovery-switch { |
| rec_mode_l: rec-mode-l { |
| rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| sdio0 { |
| wifi_enable_h: wifienable-h { |
| rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| /* NOTE: mislabelled on schematic; should be bt_enable_h */ |
| bt_enable_l: bt-enable-l { |
| rockchip,pins = <4 29 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| /* |
| * We run sdio0 at max speed; bump up drive strength. |
| * We also have external pulls, so disable the internal ones. |
| */ |
| sdio0_bus4: sdio0-bus4 { |
| rockchip,pins = <4 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>, |
| <4 21 RK_FUNC_1 &pcfg_pull_none_drv_8ma>, |
| <4 22 RK_FUNC_1 &pcfg_pull_none_drv_8ma>, |
| <4 23 RK_FUNC_1 &pcfg_pull_none_drv_8ma>; |
| }; |
| |
| sdio0_cmd: sdio0-cmd { |
| rockchip,pins = <4 24 RK_FUNC_1 &pcfg_pull_none_drv_8ma>; |
| }; |
| |
| sdio0_clk: sdio0-clk { |
| rockchip,pins = <4 25 RK_FUNC_1 &pcfg_pull_none_drv_8ma>; |
| }; |
| }; |
| |
| tpm { |
| tpm_int_h: tpm-int-h { |
| rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| write-protect { |
| fw_wp_ap: fw-wp-ap { |
| rockchip,pins = <7 6 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| }; |
