blob: 1211b5379df1eed9d3f539b73987f73956c3b5e8 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2018 Renesas Electronics
*
* Copyright (C) 2016 Atmel
* Bo Shen <voice.shen@atmel.com>
*
* Authors: Bo Shen <voice.shen@atmel.com>
* Boris Brezillon <boris.brezillon@free-electrons.com>
* Wu, Songjun <Songjun.Wu@atmel.com>
*
* Copyright (C) 2010-2011 Freescale Semiconductor, Inc. All Rights Reserved.
*/
#include <linux/gpio/consumer.h>
#include <linux/i2c-mux.h>
#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/regmap.h>
#include <drm/drmP.h>
#include <drm/drm_atomic_helper.h>
#include <drm/drm_edid.h>
#include <drm/drm_probe_helper.h>
#define SII902X_TPI_VIDEO_DATA 0x0
#define SII902X_TPI_PIXEL_REPETITION 0x8
#define SII902X_TPI_AVI_PIXEL_REP_BUS_24BIT BIT(5)
#define SII902X_TPI_AVI_PIXEL_REP_RISING_EDGE BIT(4)
#define SII902X_TPI_AVI_PIXEL_REP_4X 3
#define SII902X_TPI_AVI_PIXEL_REP_2X 1
#define SII902X_TPI_AVI_PIXEL_REP_NONE 0
#define SII902X_TPI_CLK_RATIO_HALF (0 << 6)
#define SII902X_TPI_CLK_RATIO_1X (1 << 6)
#define SII902X_TPI_CLK_RATIO_2X (2 << 6)
#define SII902X_TPI_CLK_RATIO_4X (3 << 6)
#define SII902X_TPI_AVI_IN_FORMAT 0x9
#define SII902X_TPI_AVI_INPUT_BITMODE_12BIT BIT(7)
#define SII902X_TPI_AVI_INPUT_DITHER BIT(6)
#define SII902X_TPI_AVI_INPUT_RANGE_LIMITED (2 << 2)
#define SII902X_TPI_AVI_INPUT_RANGE_FULL (1 << 2)
#define SII902X_TPI_AVI_INPUT_RANGE_AUTO (0 << 2)
#define SII902X_TPI_AVI_INPUT_COLORSPACE_BLACK (3 << 0)
#define SII902X_TPI_AVI_INPUT_COLORSPACE_YUV422 (2 << 0)
#define SII902X_TPI_AVI_INPUT_COLORSPACE_YUV444 (1 << 0)
#define SII902X_TPI_AVI_INPUT_COLORSPACE_RGB (0 << 0)
#define SII902X_TPI_AVI_INFOFRAME 0x0c
#define SII902X_SYS_CTRL_DATA 0x1a
#define SII902X_SYS_CTRL_PWR_DWN BIT(4)
#define SII902X_SYS_CTRL_AV_MUTE BIT(3)
#define SII902X_SYS_CTRL_DDC_BUS_REQ BIT(2)
#define SII902X_SYS_CTRL_DDC_BUS_GRTD BIT(1)
#define SII902X_SYS_CTRL_OUTPUT_MODE BIT(0)
#define SII902X_SYS_CTRL_OUTPUT_HDMI 1
#define SII902X_SYS_CTRL_OUTPUT_DVI 0
#define SII902X_REG_CHIPID(n) (0x1b + (n))
#define SII902X_PWR_STATE_CTRL 0x1e
#define SII902X_AVI_POWER_STATE_MSK GENMASK(1, 0)
#define SII902X_AVI_POWER_STATE_D(l) ((l) & SII902X_AVI_POWER_STATE_MSK)
#define SII902X_INT_ENABLE 0x3c
#define SII902X_INT_STATUS 0x3d
#define SII902X_HOTPLUG_EVENT BIT(0)
#define SII902X_PLUGGED_STATUS BIT(2)
#define SII902X_REG_TPI_RQB 0xc7
#define SII902X_I2C_BUS_ACQUISITION_TIMEOUT_MS 500
struct sii902x {
struct i2c_client *i2c;
struct regmap *regmap;
struct drm_bridge bridge;
struct drm_connector connector;
struct gpio_desc *reset_gpio;
struct i2c_mux_core *i2cmux;
};
static int sii902x_read_unlocked(struct i2c_client *i2c, u8 reg, u8 *val)
{
union i2c_smbus_data data;
int ret;
ret = __i2c_smbus_xfer(i2c->adapter, i2c->addr, i2c->flags,
I2C_SMBUS_READ, reg, I2C_SMBUS_BYTE_DATA, &data);
if (ret < 0)
return ret;
*val = data.byte;
return 0;
}
static int sii902x_write_unlocked(struct i2c_client *i2c, u8 reg, u8 val)
{
union i2c_smbus_data data;
data.byte = val;
return __i2c_smbus_xfer(i2c->adapter, i2c->addr, i2c->flags,
I2C_SMBUS_WRITE, reg, I2C_SMBUS_BYTE_DATA,
&data);
}
static int sii902x_update_bits_unlocked(struct i2c_client *i2c, u8 reg, u8 mask,
u8 val)
{
int ret;
u8 status;
ret = sii902x_read_unlocked(i2c, reg, &status);
if (ret)
return ret;
status &= ~mask;
status |= val & mask;
return sii902x_write_unlocked(i2c, reg, status);
}
static inline struct sii902x *bridge_to_sii902x(struct drm_bridge *bridge)
{
return container_of(bridge, struct sii902x, bridge);
}
static inline struct sii902x *connector_to_sii902x(struct drm_connector *con)
{
return container_of(con, struct sii902x, connector);
}
static void sii902x_reset(struct sii902x *sii902x)
{
if (!sii902x->reset_gpio)
return;
gpiod_set_value(sii902x->reset_gpio, 1);
/* The datasheet says treset-min = 100us. Make it 150us to be sure. */
usleep_range(150, 200);
gpiod_set_value(sii902x->reset_gpio, 0);
}
static enum drm_connector_status
sii902x_connector_detect(struct drm_connector *connector, bool force)
{
struct sii902x *sii902x = connector_to_sii902x(connector);
unsigned int status;
regmap_read(sii902x->regmap, SII902X_INT_STATUS, &status);
return (status & SII902X_PLUGGED_STATUS) ?
connector_status_connected : connector_status_disconnected;
}
static const struct drm_connector_funcs sii902x_connector_funcs = {
.detect = sii902x_connector_detect,
.fill_modes = drm_helper_probe_single_connector_modes,
.destroy = drm_connector_cleanup,
.reset = drm_atomic_helper_connector_reset,
.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
};
static int sii902x_get_modes(struct drm_connector *connector)
{
struct sii902x *sii902x = connector_to_sii902x(connector);
u32 bus_format = MEDIA_BUS_FMT_RGB888_1X24;
struct edid *edid;
int num = 0, ret;
edid = drm_get_edid(connector, sii902x->i2cmux->adapter[0]);
drm_connector_update_edid_property(connector, edid);
if (edid) {
num = drm_add_edid_modes(connector, edid);
kfree(edid);
}
ret = drm_display_info_set_bus_formats(&connector->display_info,
&bus_format, 1);
if (ret)
return ret;
return num;
}
static enum drm_mode_status sii902x_mode_valid(struct drm_connector *connector,
struct drm_display_mode *mode)
{
/* TODO: check mode */
return MODE_OK;
}
static const struct drm_connector_helper_funcs sii902x_connector_helper_funcs = {
.get_modes = sii902x_get_modes,
.mode_valid = sii902x_mode_valid,
};
static void sii902x_bridge_disable(struct drm_bridge *bridge)
{
struct sii902x *sii902x = bridge_to_sii902x(bridge);
regmap_update_bits(sii902x->regmap, SII902X_SYS_CTRL_DATA,
SII902X_SYS_CTRL_PWR_DWN,
SII902X_SYS_CTRL_PWR_DWN);
}
static void sii902x_bridge_enable(struct drm_bridge *bridge)
{
struct sii902x *sii902x = bridge_to_sii902x(bridge);
regmap_update_bits(sii902x->regmap, SII902X_PWR_STATE_CTRL,
SII902X_AVI_POWER_STATE_MSK,
SII902X_AVI_POWER_STATE_D(0));
regmap_update_bits(sii902x->regmap, SII902X_SYS_CTRL_DATA,
SII902X_SYS_CTRL_PWR_DWN, 0);
}
static void sii902x_bridge_mode_set(struct drm_bridge *bridge,
const struct drm_display_mode *mode,
const struct drm_display_mode *adj)
{
struct sii902x *sii902x = bridge_to_sii902x(bridge);
struct regmap *regmap = sii902x->regmap;
u8 buf[HDMI_INFOFRAME_SIZE(AVI)];
struct hdmi_avi_infoframe frame;
int ret;
buf[0] = adj->clock;
buf[1] = adj->clock >> 8;
buf[2] = adj->vrefresh;
buf[3] = 0x00;
buf[4] = adj->hdisplay;
buf[5] = adj->hdisplay >> 8;
buf[6] = adj->vdisplay;
buf[7] = adj->vdisplay >> 8;
buf[8] = SII902X_TPI_CLK_RATIO_1X | SII902X_TPI_AVI_PIXEL_REP_NONE |
SII902X_TPI_AVI_PIXEL_REP_BUS_24BIT;
buf[9] = SII902X_TPI_AVI_INPUT_RANGE_AUTO |
SII902X_TPI_AVI_INPUT_COLORSPACE_RGB;
ret = regmap_bulk_write(regmap, SII902X_TPI_VIDEO_DATA, buf, 10);
if (ret)
return;
ret = drm_hdmi_avi_infoframe_from_display_mode(&frame,
&sii902x->connector, adj);
if (ret < 0) {
DRM_ERROR("couldn't fill AVI infoframe\n");
return;
}
ret = hdmi_avi_infoframe_pack(&frame, buf, sizeof(buf));
if (ret < 0) {
DRM_ERROR("failed to pack AVI infoframe: %d\n", ret);
return;
}
/* Do not send the infoframe header, but keep the CRC field. */
regmap_bulk_write(regmap, SII902X_TPI_AVI_INFOFRAME,
buf + HDMI_INFOFRAME_HEADER_SIZE - 1,
HDMI_AVI_INFOFRAME_SIZE + 1);
}
static int sii902x_bridge_attach(struct drm_bridge *bridge)
{
struct sii902x *sii902x = bridge_to_sii902x(bridge);
struct drm_device *drm = bridge->dev;
int ret;
drm_connector_helper_add(&sii902x->connector,
&sii902x_connector_helper_funcs);
if (!drm_core_check_feature(drm, DRIVER_ATOMIC)) {
dev_err(&sii902x->i2c->dev,
"sii902x driver is only compatible with DRM devices supporting atomic updates\n");
return -ENOTSUPP;
}
ret = drm_connector_init(drm, &sii902x->connector,
&sii902x_connector_funcs,
DRM_MODE_CONNECTOR_HDMIA);
if (ret)
return ret;
if (sii902x->i2c->irq > 0)
sii902x->connector.polled = DRM_CONNECTOR_POLL_HPD;
else
sii902x->connector.polled = DRM_CONNECTOR_POLL_CONNECT;
drm_connector_attach_encoder(&sii902x->connector, bridge->encoder);
return 0;
}
static const struct drm_bridge_funcs sii902x_bridge_funcs = {
.attach = sii902x_bridge_attach,
.mode_set = sii902x_bridge_mode_set,
.disable = sii902x_bridge_disable,
.enable = sii902x_bridge_enable,
};
static const struct regmap_range sii902x_volatile_ranges[] = {
{ .range_min = 0, .range_max = 0xff },
};
static const struct regmap_access_table sii902x_volatile_table = {
.yes_ranges = sii902x_volatile_ranges,
.n_yes_ranges = ARRAY_SIZE(sii902x_volatile_ranges),
};
static const struct regmap_config sii902x_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.volatile_table = &sii902x_volatile_table,
.cache_type = REGCACHE_NONE,
};
static irqreturn_t sii902x_interrupt(int irq, void *data)
{
struct sii902x *sii902x = data;
unsigned int status = 0;
regmap_read(sii902x->regmap, SII902X_INT_STATUS, &status);
regmap_write(sii902x->regmap, SII902X_INT_STATUS, status);
if ((status & SII902X_HOTPLUG_EVENT) && sii902x->bridge.dev)
drm_helper_hpd_irq_event(sii902x->bridge.dev);
return IRQ_HANDLED;
}
/*
* The purpose of sii902x_i2c_bypass_select is to enable the pass through
* mode of the HDMI transmitter. Do not use regmap from within this function,
* only use sii902x_*_unlocked functions to read/modify/write registers.
* We are holding the parent adapter lock here, keep this in mind before
* adding more i2c transactions.
*
* Also, since SII902X_SYS_CTRL_DATA is used with regmap_update_bits elsewhere
* in this driver, we need to make sure that we only touch 0x1A[2:1] from
* within sii902x_i2c_bypass_select and sii902x_i2c_bypass_deselect, and that
* we leave the remaining bits as we have found them.
*/
static int sii902x_i2c_bypass_select(struct i2c_mux_core *mux, u32 chan_id)
{
struct sii902x *sii902x = i2c_mux_priv(mux);
struct device *dev = &sii902x->i2c->dev;
unsigned long timeout;
u8 status;
int ret;
ret = sii902x_update_bits_unlocked(sii902x->i2c, SII902X_SYS_CTRL_DATA,
SII902X_SYS_CTRL_DDC_BUS_REQ,
SII902X_SYS_CTRL_DDC_BUS_REQ);
if (ret)
return ret;
timeout = jiffies +
msecs_to_jiffies(SII902X_I2C_BUS_ACQUISITION_TIMEOUT_MS);
do {
ret = sii902x_read_unlocked(sii902x->i2c, SII902X_SYS_CTRL_DATA,
&status);
if (ret)
return ret;
} while (!(status & SII902X_SYS_CTRL_DDC_BUS_GRTD) &&
time_before(jiffies, timeout));
if (!(status & SII902X_SYS_CTRL_DDC_BUS_GRTD)) {
dev_err(dev, "Failed to acquire the i2c bus\n");
return -ETIMEDOUT;
}
return sii902x_write_unlocked(sii902x->i2c, SII902X_SYS_CTRL_DATA,
status);
}
/*
* The purpose of sii902x_i2c_bypass_deselect is to disable the pass through
* mode of the HDMI transmitter. Do not use regmap from within this function,
* only use sii902x_*_unlocked functions to read/modify/write registers.
* We are holding the parent adapter lock here, keep this in mind before
* adding more i2c transactions.
*
* Also, since SII902X_SYS_CTRL_DATA is used with regmap_update_bits elsewhere
* in this driver, we need to make sure that we only touch 0x1A[2:1] from
* within sii902x_i2c_bypass_select and sii902x_i2c_bypass_deselect, and that
* we leave the remaining bits as we have found them.
*/
static int sii902x_i2c_bypass_deselect(struct i2c_mux_core *mux, u32 chan_id)
{
struct sii902x *sii902x = i2c_mux_priv(mux);
struct device *dev = &sii902x->i2c->dev;
unsigned long timeout;
unsigned int retries;
u8 status;
int ret;
/*
* When the HDMI transmitter is in pass through mode, we need an
* (undocumented) additional delay between STOP and START conditions
* to guarantee the bus won't get stuck.
*/
udelay(30);
/*
* Sometimes the I2C bus can stall after failure to use the
* EDID channel. Retry a few times to see if things clear
* up, else continue anyway.
*/
retries = 5;
do {
ret = sii902x_read_unlocked(sii902x->i2c, SII902X_SYS_CTRL_DATA,
&status);
retries--;
} while (ret && retries);
if (ret) {
dev_err(dev, "failed to read status (%d)\n", ret);
return ret;
}
ret = sii902x_update_bits_unlocked(sii902x->i2c, SII902X_SYS_CTRL_DATA,
SII902X_SYS_CTRL_DDC_BUS_REQ |
SII902X_SYS_CTRL_DDC_BUS_GRTD, 0);
if (ret)
return ret;
timeout = jiffies +
msecs_to_jiffies(SII902X_I2C_BUS_ACQUISITION_TIMEOUT_MS);
do {
ret = sii902x_read_unlocked(sii902x->i2c, SII902X_SYS_CTRL_DATA,
&status);
if (ret)
return ret;
} while (status & (SII902X_SYS_CTRL_DDC_BUS_REQ |
SII902X_SYS_CTRL_DDC_BUS_GRTD) &&
time_before(jiffies, timeout));
if (status & (SII902X_SYS_CTRL_DDC_BUS_REQ |
SII902X_SYS_CTRL_DDC_BUS_GRTD)) {
dev_err(dev, "failed to release the i2c bus\n");
return -ETIMEDOUT;
}
return 0;
}
static int sii902x_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
unsigned int status = 0;
struct sii902x *sii902x;
u8 chipid[4];
int ret;
ret = i2c_check_functionality(client->adapter,
I2C_FUNC_SMBUS_BYTE_DATA);
if (!ret) {
dev_err(dev, "I2C adapter not suitable\n");
return -EIO;
}
sii902x = devm_kzalloc(dev, sizeof(*sii902x), GFP_KERNEL);
if (!sii902x)
return -ENOMEM;
sii902x->i2c = client;
sii902x->regmap = devm_regmap_init_i2c(client, &sii902x_regmap_config);
if (IS_ERR(sii902x->regmap))
return PTR_ERR(sii902x->regmap);
sii902x->reset_gpio = devm_gpiod_get_optional(dev, "reset",
GPIOD_OUT_LOW);
if (IS_ERR(sii902x->reset_gpio)) {
dev_err(dev, "Failed to retrieve/request reset gpio: %ld\n",
PTR_ERR(sii902x->reset_gpio));
return PTR_ERR(sii902x->reset_gpio);
}
sii902x_reset(sii902x);
ret = regmap_write(sii902x->regmap, SII902X_REG_TPI_RQB, 0x0);
if (ret)
return ret;
ret = regmap_bulk_read(sii902x->regmap, SII902X_REG_CHIPID(0),
&chipid, 4);
if (ret) {
dev_err(dev, "regmap_read failed %d\n", ret);
return ret;
}
if (chipid[0] != 0xb0) {
dev_err(dev, "Invalid chipid: %02x (expecting 0xb0)\n",
chipid[0]);
return -EINVAL;
}
/* Clear all pending interrupts */
regmap_read(sii902x->regmap, SII902X_INT_STATUS, &status);
regmap_write(sii902x->regmap, SII902X_INT_STATUS, status);
if (client->irq > 0) {
regmap_write(sii902x->regmap, SII902X_INT_ENABLE,
SII902X_HOTPLUG_EVENT);
ret = devm_request_threaded_irq(dev, client->irq, NULL,
sii902x_interrupt,
IRQF_ONESHOT, dev_name(dev),
sii902x);
if (ret)
return ret;
}
sii902x->bridge.funcs = &sii902x_bridge_funcs;
sii902x->bridge.of_node = dev->of_node;
drm_bridge_add(&sii902x->bridge);
i2c_set_clientdata(client, sii902x);
sii902x->i2cmux = i2c_mux_alloc(client->adapter, dev,
1, 0, I2C_MUX_GATE,
sii902x_i2c_bypass_select,
sii902x_i2c_bypass_deselect);
if (!sii902x->i2cmux)
return -ENOMEM;
sii902x->i2cmux->priv = sii902x;
return i2c_mux_add_adapter(sii902x->i2cmux, 0, 0, 0);
}
static int sii902x_remove(struct i2c_client *client)
{
struct sii902x *sii902x = i2c_get_clientdata(client);
i2c_mux_del_adapters(sii902x->i2cmux);
drm_bridge_remove(&sii902x->bridge);
return 0;
}
static const struct of_device_id sii902x_dt_ids[] = {
{ .compatible = "sil,sii9022", },
{ }
};
MODULE_DEVICE_TABLE(of, sii902x_dt_ids);
static const struct i2c_device_id sii902x_i2c_ids[] = {
{ "sii9022", 0 },
{ },
};
MODULE_DEVICE_TABLE(i2c, sii902x_i2c_ids);
static struct i2c_driver sii902x_driver = {
.probe = sii902x_probe,
.remove = sii902x_remove,
.driver = {
.name = "sii902x",
.of_match_table = sii902x_dt_ids,
},
.id_table = sii902x_i2c_ids,
};
module_i2c_driver(sii902x_driver);
MODULE_AUTHOR("Boris Brezillon <boris.brezillon@free-electrons.com>");
MODULE_DESCRIPTION("SII902x RGB -> HDMI bridges");
MODULE_LICENSE("GPL");