| /******************************************************************************* | |
| * | |
| * (c) 1998 by Computone Corporation | |
| * | |
| ******************************************************************************** | |
| * | |
| * | |
| * PACKAGE: Linux tty Device Driver for IntelliPort II family of multiport | |
| * serial I/O controllers. | |
| * | |
| * DESCRIPTION: Driver constants for configuration and tuning | |
| * | |
| * NOTES: | |
| * | |
| *******************************************************************************/ | |
| #ifndef IP2_H | |
| #define IP2_H | |
| #include "ip2types.h" | |
| #include "i2cmd.h" | |
| /*************/ | |
| /* Constants */ | |
| /*************/ | |
| /* Device major numbers - since version 2.0.26. */ | |
| #define IP2_TTY_MAJOR 71 | |
| #define IP2_CALLOUT_MAJOR 72 | |
| #define IP2_IPL_MAJOR 73 | |
| /* Board configuration array. | |
| * This array defines the hardware irq and address for up to IP2_MAX_BOARDS | |
| * (4 supported per ip2_types.h) ISA board addresses and irqs MUST be specified, | |
| * PCI and EISA boards are probed for and automagicly configed | |
| * iff the addresses are set to 1 and 2 respectivily. | |
| * 0x0100 - 0x03f0 == ISA | |
| * 1 == PCI | |
| * 2 == EISA | |
| * 0 == (skip this board) | |
| * This array defines the hardware addresses for them. Special | |
| * addresses are EISA and PCI which go sniffing for boards. | |
| * In a multiboard system the position in the array determines which port | |
| * devices are assigned to each board: | |
| * board 0 is assigned ttyF0.. to ttyF63, | |
| * board 1 is assigned ttyF64 to ttyF127, | |
| * board 2 is assigned ttyF128 to ttyF191, | |
| * board 3 is assigned ttyF192 to ttyF255. | |
| * | |
| * In PCI and EISA bus systems each range is mapped to card in | |
| * monotonically increasing slot number order, ISA position is as specified | |
| * here. | |
| * If the irqs are ALL set to 0,0,0,0 all boards operate in | |
| * polled mode. For interrupt operation ISA boards require that the IRQ be | |
| * specified, while PCI and EISA boards any nonzero entry | |
| * will enable interrupts using the BIOS configured irq for the board. | |
| * An invalid irq entry will default to polled mode for that card and print | |
| * console warning. | |
| * When the driver is loaded as a module these setting can be overridden on the | |
| * modprobe command line or on an option line in /etc/modprobe.conf. | |
| * If the driver is built-in the configuration must be | |
| * set here for ISA cards and address set to 1 and 2 for PCI and EISA. | |
| * | |
| * Here is an example that shows most if not all possibe combinations: | |
| *static ip2config_t ip2config = | |
| *{ | |
| * {11,1,0,0}, // irqs | |
| * { // Addresses | |
| * 0x0308, // Board 0, ttyF0 - ttyF63// ISA card at io=0x308, irq=11 | |
| * 0x0001, // Board 1, ttyF64 - ttyF127//PCI card configured by BIOS | |
| * 0x0000, // Board 2, ttyF128 - ttyF191// Slot skipped | |
| * 0x0002 // Board 3, ttyF192 - ttyF255//EISA card configured by BIOS | |
| * // but polled not irq driven | |
| * } | |
| *}; | |
| */ | |
| /* this structure is zeroed out because the suggested method is to configure | |
| * the driver as a module, set up the parameters with an options line in | |
| * /etc/modprobe.conf and load with modprobe or kmod, the kernel | |
| * module loader | |
| */ | |
| /* This structure is NOW always initialized when the driver is initialized. | |
| * Compiled in defaults MUST be added to the io and irq arrays in | |
| * ip2.c. Those values are configurable from insmod parameters in the | |
| * case of modules or from command line parameters (ip2=io,irq) when | |
| * compiled in. | |
| */ | |
| static ip2config_t ip2config = | |
| { | |
| {0,0,0,0}, // irqs | |
| { // Addresses | |
| /* Do NOT set compile time defaults HERE! Use the arrays in | |
| ip2.c! These WILL be overwritten! =mhw= */ | |
| 0x0000, // Board 0, ttyF0 - ttyF63 | |
| 0x0000, // Board 1, ttyF64 - ttyF127 | |
| 0x0000, // Board 2, ttyF128 - ttyF191 | |
| 0x0000 // Board 3, ttyF192 - ttyF255 | |
| } | |
| }; | |
| #endif |