| #ifndef __ASM_ARM_SYSTEM_H | |
| #define __ASM_ARM_SYSTEM_H | |
| #ifdef __KERNEL__ | |
| #define CPU_ARCH_UNKNOWN 0 | |
| #define CPU_ARCH_ARMv3 1 | |
| #define CPU_ARCH_ARMv4 2 | |
| #define CPU_ARCH_ARMv4T 3 | |
| #define CPU_ARCH_ARMv5 4 | |
| #define CPU_ARCH_ARMv5T 5 | |
| #define CPU_ARCH_ARMv5TE 6 | |
| #define CPU_ARCH_ARMv5TEJ 7 | |
| #define CPU_ARCH_ARMv6 8 | |
| /* | |
| * CR1 bits (CP#15 CR1) | |
| */ | |
| #define CR_M (1 << 0) /* MMU enable */ | |
| #define CR_A (1 << 1) /* Alignment abort enable */ | |
| #define CR_C (1 << 2) /* Dcache enable */ | |
| #define CR_W (1 << 3) /* Write buffer enable */ | |
| #define CR_P (1 << 4) /* 32-bit exception handler */ | |
| #define CR_D (1 << 5) /* 32-bit data address range */ | |
| #define CR_L (1 << 6) /* Implementation defined */ | |
| #define CR_B (1 << 7) /* Big endian */ | |
| #define CR_S (1 << 8) /* System MMU protection */ | |
| #define CR_R (1 << 9) /* ROM MMU protection */ | |
| #define CR_F (1 << 10) /* Implementation defined */ | |
| #define CR_Z (1 << 11) /* Implementation defined */ | |
| #define CR_I (1 << 12) /* Icache enable */ | |
| #define CR_V (1 << 13) /* Vectors relocated to 0xffff0000 */ | |
| #define CR_RR (1 << 14) /* Round Robin cache replacement */ | |
| #define CR_L4 (1 << 15) /* LDR pc can set T bit */ | |
| #define CR_DT (1 << 16) | |
| #define CR_IT (1 << 18) | |
| #define CR_ST (1 << 19) | |
| #define CR_FI (1 << 21) /* Fast interrupt (lower latency mode) */ | |
| #define CR_U (1 << 22) /* Unaligned access operation */ | |
| #define CR_XP (1 << 23) /* Extended page tables */ | |
| #define CR_VE (1 << 24) /* Vectored interrupts */ | |
| #define CPUID_ID 0 | |
| #define CPUID_CACHETYPE 1 | |
| #define CPUID_TCM 2 | |
| #define CPUID_TLBTYPE 3 | |
| #define read_cpuid(reg) \ | |
| ({ \ | |
| unsigned int __val; \ | |
| asm("mrc p15, 0, %0, c0, c0, " __stringify(reg) \ | |
| : "=r" (__val) \ | |
| : \ | |
| : "cc"); \ | |
| __val; \ | |
| }) | |
| /* | |
| * This is used to ensure the compiler did actually allocate the register we | |
| * asked it for some inline assembly sequences. Apparently we can't trust | |
| * the compiler from one version to another so a bit of paranoia won't hurt. | |
| * This string is meant to be concatenated with the inline asm string and | |
| * will cause compilation to stop on mismatch. | |
| * (for details, see gcc PR 15089) | |
| */ | |
| #define __asmeq(x, y) ".ifnc " x "," y " ; .err ; .endif\n\t" | |
| #ifndef __ASSEMBLY__ | |
| #include <linux/linkage.h> | |
| struct thread_info; | |
| struct task_struct; | |
| /* information about the system we're running on */ | |
| extern unsigned int system_rev; | |
| extern unsigned int system_serial_low; | |
| extern unsigned int system_serial_high; | |
| extern unsigned int mem_fclk_21285; | |
| struct pt_regs; | |
| void die(const char *msg, struct pt_regs *regs, int err) | |
| __attribute__((noreturn)); | |
| struct siginfo; | |
| void notify_die(const char *str, struct pt_regs *regs, struct siginfo *info, | |
| unsigned long err, unsigned long trap); | |
| void hook_fault_code(int nr, int (*fn)(unsigned long, unsigned int, | |
| struct pt_regs *), | |
| int sig, const char *name); | |
| #define xchg(ptr,x) \ | |
| ((__typeof__(*(ptr)))__xchg((unsigned long)(x),(ptr),sizeof(*(ptr)))) | |
| #define tas(ptr) (xchg((ptr),1)) | |
| extern asmlinkage void __backtrace(void); | |
| extern asmlinkage void c_backtrace(unsigned long fp, int pmode); | |
| struct mm_struct; | |
| extern void show_pte(struct mm_struct *mm, unsigned long addr); | |
| extern void __show_regs(struct pt_regs *); | |
| extern int cpu_architecture(void); | |
| extern void cpu_init(void); | |
| void arm_machine_restart(char mode); | |
| extern void (*arm_pm_restart)(char str); | |
| /* | |
| * Intel's XScale3 core supports some v6 features (supersections, L2) | |
| * but advertises itself as v5 as it does not support the v6 ISA. For | |
| * this reason, we need a way to explicitly test for this type of CPU. | |
| */ | |
| #ifndef CONFIG_CPU_XSC3 | |
| #define cpu_is_xsc3() 0 | |
| #else | |
| static inline int cpu_is_xsc3(void) | |
| { | |
| extern unsigned int processor_id; | |
| if ((processor_id & 0xffffe000) == 0x69056000) | |
| return 1; | |
| return 0; | |
| } | |
| #endif | |
| #if !defined(CONFIG_CPU_XSCALE) && !defined(CONFIG_CPU_XSC3) | |
| #define cpu_is_xscale() 0 | |
| #else | |
| #define cpu_is_xscale() 1 | |
| #endif | |
| #define set_cr(x) \ | |
| __asm__ __volatile__( \ | |
| "mcr p15, 0, %0, c1, c0, 0 @ set CR" \ | |
| : : "r" (x) : "cc") | |
| #define get_cr() \ | |
| ({ \ | |
| unsigned int __val; \ | |
| __asm__ __volatile__( \ | |
| "mrc p15, 0, %0, c1, c0, 0 @ get CR" \ | |
| : "=r" (__val) : : "cc"); \ | |
| __val; \ | |
| }) | |
| extern unsigned long cr_no_alignment; /* defined in entry-armv.S */ | |
| extern unsigned long cr_alignment; /* defined in entry-armv.S */ | |
| #define UDBG_UNDEFINED (1 << 0) | |
| #define UDBG_SYSCALL (1 << 1) | |
| #define UDBG_BADABORT (1 << 2) | |
| #define UDBG_SEGV (1 << 3) | |
| #define UDBG_BUS (1 << 4) | |
| extern unsigned int user_debug; | |
| #if __LINUX_ARM_ARCH__ >= 4 | |
| #define vectors_high() (cr_alignment & CR_V) | |
| #else | |
| #define vectors_high() (0) | |
| #endif | |
| #if __LINUX_ARM_ARCH__ >= 6 | |
| #define mb() __asm__ __volatile__ ("mcr p15, 0, %0, c7, c10, 5" \ | |
| : : "r" (0) : "memory") | |
| #else | |
| #define mb() __asm__ __volatile__ ("" : : : "memory") | |
| #endif | |
| #define rmb() mb() | |
| #define wmb() mb() | |
| #define read_barrier_depends() do { } while(0) | |
| #define set_mb(var, value) do { var = value; mb(); } while (0) | |
| #define nop() __asm__ __volatile__("mov\tr0,r0\t@ nop\n\t"); | |
| /* | |
| * switch_mm() may do a full cache flush over the context switch, | |
| * so enable interrupts over the context switch to avoid high | |
| * latency. | |
| */ | |
| #define __ARCH_WANT_INTERRUPTS_ON_CTXSW | |
| /* | |
| * switch_to(prev, next) should switch from task `prev' to `next' | |
| * `prev' will never be the same as `next'. schedule() itself | |
| * contains the memory barrier to tell GCC not to cache `current'. | |
| */ | |
| extern struct task_struct *__switch_to(struct task_struct *, struct thread_info *, struct thread_info *); | |
| #define switch_to(prev,next,last) \ | |
| do { \ | |
| last = __switch_to(prev,task_thread_info(prev), task_thread_info(next)); \ | |
| } while (0) | |
| /* | |
| * On SMP systems, when the scheduler does migration-cost autodetection, | |
| * it needs a way to flush as much of the CPU's caches as possible. | |
| * | |
| * TODO: fill this in! | |
| */ | |
| static inline void sched_cacheflush(void) | |
| { | |
| } | |
| /* | |
| * CPU interrupt mask handling. | |
| */ | |
| #if __LINUX_ARM_ARCH__ >= 6 | |
| #define local_irq_save(x) \ | |
| ({ \ | |
| __asm__ __volatile__( \ | |
| "mrs %0, cpsr @ local_irq_save\n" \ | |
| "cpsid i" \ | |
| : "=r" (x) : : "memory", "cc"); \ | |
| }) | |
| #define local_irq_enable() __asm__("cpsie i @ __sti" : : : "memory", "cc") | |
| #define local_irq_disable() __asm__("cpsid i @ __cli" : : : "memory", "cc") | |
| #define local_fiq_enable() __asm__("cpsie f @ __stf" : : : "memory", "cc") | |
| #define local_fiq_disable() __asm__("cpsid f @ __clf" : : : "memory", "cc") | |
| #else | |
| /* | |
| * Save the current interrupt enable state & disable IRQs | |
| */ | |
| #define local_irq_save(x) \ | |
| ({ \ | |
| unsigned long temp; \ | |
| (void) (&temp == &x); \ | |
| __asm__ __volatile__( \ | |
| "mrs %0, cpsr @ local_irq_save\n" \ | |
| " orr %1, %0, #128\n" \ | |
| " msr cpsr_c, %1" \ | |
| : "=r" (x), "=r" (temp) \ | |
| : \ | |
| : "memory", "cc"); \ | |
| }) | |
| /* | |
| * Enable IRQs | |
| */ | |
| #define local_irq_enable() \ | |
| ({ \ | |
| unsigned long temp; \ | |
| __asm__ __volatile__( \ | |
| "mrs %0, cpsr @ local_irq_enable\n" \ | |
| " bic %0, %0, #128\n" \ | |
| " msr cpsr_c, %0" \ | |
| : "=r" (temp) \ | |
| : \ | |
| : "memory", "cc"); \ | |
| }) | |
| /* | |
| * Disable IRQs | |
| */ | |
| #define local_irq_disable() \ | |
| ({ \ | |
| unsigned long temp; \ | |
| __asm__ __volatile__( \ | |
| "mrs %0, cpsr @ local_irq_disable\n" \ | |
| " orr %0, %0, #128\n" \ | |
| " msr cpsr_c, %0" \ | |
| : "=r" (temp) \ | |
| : \ | |
| : "memory", "cc"); \ | |
| }) | |
| /* | |
| * Enable FIQs | |
| */ | |
| #define local_fiq_enable() \ | |
| ({ \ | |
| unsigned long temp; \ | |
| __asm__ __volatile__( \ | |
| "mrs %0, cpsr @ stf\n" \ | |
| " bic %0, %0, #64\n" \ | |
| " msr cpsr_c, %0" \ | |
| : "=r" (temp) \ | |
| : \ | |
| : "memory", "cc"); \ | |
| }) | |
| /* | |
| * Disable FIQs | |
| */ | |
| #define local_fiq_disable() \ | |
| ({ \ | |
| unsigned long temp; \ | |
| __asm__ __volatile__( \ | |
| "mrs %0, cpsr @ clf\n" \ | |
| " orr %0, %0, #64\n" \ | |
| " msr cpsr_c, %0" \ | |
| : "=r" (temp) \ | |
| : \ | |
| : "memory", "cc"); \ | |
| }) | |
| #endif | |
| /* | |
| * Save the current interrupt enable state. | |
| */ | |
| #define local_save_flags(x) \ | |
| ({ \ | |
| __asm__ __volatile__( \ | |
| "mrs %0, cpsr @ local_save_flags" \ | |
| : "=r" (x) : : "memory", "cc"); \ | |
| }) | |
| /* | |
| * restore saved IRQ & FIQ state | |
| */ | |
| #define local_irq_restore(x) \ | |
| __asm__ __volatile__( \ | |
| "msr cpsr_c, %0 @ local_irq_restore\n" \ | |
| : \ | |
| : "r" (x) \ | |
| : "memory", "cc") | |
| #define irqs_disabled() \ | |
| ({ \ | |
| unsigned long flags; \ | |
| local_save_flags(flags); \ | |
| (int)(flags & PSR_I_BIT); \ | |
| }) | |
| #ifdef CONFIG_SMP | |
| #define smp_mb() mb() | |
| #define smp_rmb() rmb() | |
| #define smp_wmb() wmb() | |
| #define smp_read_barrier_depends() read_barrier_depends() | |
| #else | |
| #define smp_mb() barrier() | |
| #define smp_rmb() barrier() | |
| #define smp_wmb() barrier() | |
| #define smp_read_barrier_depends() do { } while(0) | |
| #endif /* CONFIG_SMP */ | |
| #if defined(CONFIG_CPU_SA1100) || defined(CONFIG_CPU_SA110) | |
| /* | |
| * On the StrongARM, "swp" is terminally broken since it bypasses the | |
| * cache totally. This means that the cache becomes inconsistent, and, | |
| * since we use normal loads/stores as well, this is really bad. | |
| * Typically, this causes oopsen in filp_close, but could have other, | |
| * more disasterous effects. There are two work-arounds: | |
| * 1. Disable interrupts and emulate the atomic swap | |
| * 2. Clean the cache, perform atomic swap, flush the cache | |
| * | |
| * We choose (1) since its the "easiest" to achieve here and is not | |
| * dependent on the processor type. | |
| * | |
| * NOTE that this solution won't work on an SMP system, so explcitly | |
| * forbid it here. | |
| */ | |
| #define swp_is_buggy | |
| #endif | |
| static inline unsigned long __xchg(unsigned long x, volatile void *ptr, int size) | |
| { | |
| extern void __bad_xchg(volatile void *, int); | |
| unsigned long ret; | |
| #ifdef swp_is_buggy | |
| unsigned long flags; | |
| #endif | |
| #if __LINUX_ARM_ARCH__ >= 6 | |
| unsigned int tmp; | |
| #endif | |
| switch (size) { | |
| #if __LINUX_ARM_ARCH__ >= 6 | |
| case 1: | |
| asm volatile("@ __xchg1\n" | |
| "1: ldrexb %0, [%3]\n" | |
| " strexb %1, %2, [%3]\n" | |
| " teq %1, #0\n" | |
| " bne 1b" | |
| : "=&r" (ret), "=&r" (tmp) | |
| : "r" (x), "r" (ptr) | |
| : "memory", "cc"); | |
| break; | |
| case 4: | |
| asm volatile("@ __xchg4\n" | |
| "1: ldrex %0, [%3]\n" | |
| " strex %1, %2, [%3]\n" | |
| " teq %1, #0\n" | |
| " bne 1b" | |
| : "=&r" (ret), "=&r" (tmp) | |
| : "r" (x), "r" (ptr) | |
| : "memory", "cc"); | |
| break; | |
| #elif defined(swp_is_buggy) | |
| #ifdef CONFIG_SMP | |
| #error SMP is not supported on this platform | |
| #endif | |
| case 1: | |
| local_irq_save(flags); | |
| ret = *(volatile unsigned char *)ptr; | |
| *(volatile unsigned char *)ptr = x; | |
| local_irq_restore(flags); | |
| break; | |
| case 4: | |
| local_irq_save(flags); | |
| ret = *(volatile unsigned long *)ptr; | |
| *(volatile unsigned long *)ptr = x; | |
| local_irq_restore(flags); | |
| break; | |
| #else | |
| case 1: | |
| asm volatile("@ __xchg1\n" | |
| " swpb %0, %1, [%2]" | |
| : "=&r" (ret) | |
| : "r" (x), "r" (ptr) | |
| : "memory", "cc"); | |
| break; | |
| case 4: | |
| asm volatile("@ __xchg4\n" | |
| " swp %0, %1, [%2]" | |
| : "=&r" (ret) | |
| : "r" (x), "r" (ptr) | |
| : "memory", "cc"); | |
| break; | |
| #endif | |
| default: | |
| __bad_xchg(ptr, size), ret = 0; | |
| break; | |
| } | |
| return ret; | |
| } | |
| extern void disable_hlt(void); | |
| extern void enable_hlt(void); | |
| #endif /* __ASSEMBLY__ */ | |
| #define arch_align_stack(x) (x) | |
| #endif /* __KERNEL__ */ | |
| #endif |