| /* | |
| * Copyright (c) 2008 Atheros Communications Inc. | |
| * | |
| * Permission to use, copy, modify, and/or distribute this software for any | |
| * purpose with or without fee is hereby granted, provided that the above | |
| * copyright notice and this permission notice appear in all copies. | |
| * | |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES | |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR | |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES | |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN | |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF | |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. | |
| */ | |
| #include <linux/nl80211.h> | |
| #include "core.h" | |
| #include "reg.h" | |
| #include "hw.h" | |
| #define ATH_PCI_VERSION "0.1" | |
| static char *dev_info = "ath9k"; | |
| MODULE_AUTHOR("Atheros Communications"); | |
| MODULE_DESCRIPTION("Support for Atheros 802.11n wireless LAN cards."); | |
| MODULE_SUPPORTED_DEVICE("Atheros 802.11n WLAN cards"); | |
| MODULE_LICENSE("Dual BSD/GPL"); | |
| static struct pci_device_id ath_pci_id_table[] __devinitdata = { | |
| { PCI_VDEVICE(ATHEROS, 0x0023) }, /* PCI */ | |
| { PCI_VDEVICE(ATHEROS, 0x0024) }, /* PCI-E */ | |
| { PCI_VDEVICE(ATHEROS, 0x0027) }, /* PCI */ | |
| { PCI_VDEVICE(ATHEROS, 0x0029) }, /* PCI */ | |
| { PCI_VDEVICE(ATHEROS, 0x002A) }, /* PCI-E */ | |
| { PCI_VDEVICE(ATHEROS, 0x002B) }, /* PCI-E */ | |
| { 0 } | |
| }; | |
| static void ath_detach(struct ath_softc *sc); | |
| /* return bus cachesize in 4B word units */ | |
| static void bus_read_cachesize(struct ath_softc *sc, int *csz) | |
| { | |
| u8 u8tmp; | |
| pci_read_config_byte(sc->pdev, PCI_CACHE_LINE_SIZE, (u8 *)&u8tmp); | |
| *csz = (int)u8tmp; | |
| /* | |
| * This check was put in to avoid "unplesant" consequences if | |
| * the bootrom has not fully initialized all PCI devices. | |
| * Sometimes the cache line size register is not set | |
| */ | |
| if (*csz == 0) | |
| *csz = DEFAULT_CACHELINE >> 2; /* Use the default size */ | |
| } | |
| static void ath_setcurmode(struct ath_softc *sc, enum wireless_mode mode) | |
| { | |
| sc->cur_rate_table = sc->hw_rate_table[mode]; | |
| /* | |
| * All protection frames are transmited at 2Mb/s for | |
| * 11g, otherwise at 1Mb/s. | |
| * XXX select protection rate index from rate table. | |
| */ | |
| sc->sc_protrix = (mode == ATH9K_MODE_11G ? 1 : 0); | |
| } | |
| static enum wireless_mode ath_chan2mode(struct ath9k_channel *chan) | |
| { | |
| if (chan->chanmode == CHANNEL_A) | |
| return ATH9K_MODE_11A; | |
| else if (chan->chanmode == CHANNEL_G) | |
| return ATH9K_MODE_11G; | |
| else if (chan->chanmode == CHANNEL_B) | |
| return ATH9K_MODE_11B; | |
| else if (chan->chanmode == CHANNEL_A_HT20) | |
| return ATH9K_MODE_11NA_HT20; | |
| else if (chan->chanmode == CHANNEL_G_HT20) | |
| return ATH9K_MODE_11NG_HT20; | |
| else if (chan->chanmode == CHANNEL_A_HT40PLUS) | |
| return ATH9K_MODE_11NA_HT40PLUS; | |
| else if (chan->chanmode == CHANNEL_A_HT40MINUS) | |
| return ATH9K_MODE_11NA_HT40MINUS; | |
| else if (chan->chanmode == CHANNEL_G_HT40PLUS) | |
| return ATH9K_MODE_11NG_HT40PLUS; | |
| else if (chan->chanmode == CHANNEL_G_HT40MINUS) | |
| return ATH9K_MODE_11NG_HT40MINUS; | |
| WARN_ON(1); /* should not get here */ | |
| return ATH9K_MODE_11B; | |
| } | |
| static void ath_update_txpow(struct ath_softc *sc) | |
| { | |
| struct ath_hal *ah = sc->sc_ah; | |
| u32 txpow; | |
| if (sc->sc_curtxpow != sc->sc_config.txpowlimit) { | |
| ath9k_hw_set_txpowerlimit(ah, sc->sc_config.txpowlimit); | |
| /* read back in case value is clamped */ | |
| ath9k_hw_getcapability(ah, ATH9K_CAP_TXPOW, 1, &txpow); | |
| sc->sc_curtxpow = txpow; | |
| } | |
| } | |
| static u8 parse_mpdudensity(u8 mpdudensity) | |
| { | |
| /* | |
| * 802.11n D2.0 defined values for "Minimum MPDU Start Spacing": | |
| * 0 for no restriction | |
| * 1 for 1/4 us | |
| * 2 for 1/2 us | |
| * 3 for 1 us | |
| * 4 for 2 us | |
| * 5 for 4 us | |
| * 6 for 8 us | |
| * 7 for 16 us | |
| */ | |
| switch (mpdudensity) { | |
| case 0: | |
| return 0; | |
| case 1: | |
| case 2: | |
| case 3: | |
| /* Our lower layer calculations limit our precision to | |
| 1 microsecond */ | |
| return 1; | |
| case 4: | |
| return 2; | |
| case 5: | |
| return 4; | |
| case 6: | |
| return 8; | |
| case 7: | |
| return 16; | |
| default: | |
| return 0; | |
| } | |
| } | |
| static void ath_setup_rates(struct ath_softc *sc, enum ieee80211_band band) | |
| { | |
| struct ath_rate_table *rate_table = NULL; | |
| struct ieee80211_supported_band *sband; | |
| struct ieee80211_rate *rate; | |
| int i, maxrates; | |
| switch (band) { | |
| case IEEE80211_BAND_2GHZ: | |
| rate_table = sc->hw_rate_table[ATH9K_MODE_11G]; | |
| break; | |
| case IEEE80211_BAND_5GHZ: | |
| rate_table = sc->hw_rate_table[ATH9K_MODE_11A]; | |
| break; | |
| default: | |
| break; | |
| } | |
| if (rate_table == NULL) | |
| return; | |
| sband = &sc->sbands[band]; | |
| rate = sc->rates[band]; | |
| if (rate_table->rate_cnt > ATH_RATE_MAX) | |
| maxrates = ATH_RATE_MAX; | |
| else | |
| maxrates = rate_table->rate_cnt; | |
| for (i = 0; i < maxrates; i++) { | |
| rate[i].bitrate = rate_table->info[i].ratekbps / 100; | |
| rate[i].hw_value = rate_table->info[i].ratecode; | |
| sband->n_bitrates++; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Rate: %2dMbps, ratecode: %2d\n", | |
| rate[i].bitrate / 10, rate[i].hw_value); | |
| } | |
| } | |
| static int ath_setup_channels(struct ath_softc *sc) | |
| { | |
| struct ath_hal *ah = sc->sc_ah; | |
| int nchan, i, a = 0, b = 0; | |
| u8 regclassids[ATH_REGCLASSIDS_MAX]; | |
| u32 nregclass = 0; | |
| struct ieee80211_supported_band *band_2ghz; | |
| struct ieee80211_supported_band *band_5ghz; | |
| struct ieee80211_channel *chan_2ghz; | |
| struct ieee80211_channel *chan_5ghz; | |
| struct ath9k_channel *c; | |
| /* Fill in ah->ah_channels */ | |
| if (!ath9k_regd_init_channels(ah, ATH_CHAN_MAX, (u32 *)&nchan, | |
| regclassids, ATH_REGCLASSIDS_MAX, | |
| &nregclass, CTRY_DEFAULT, false, 1)) { | |
| u32 rd = ah->ah_currentRD; | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to collect channel list; " | |
| "regdomain likely %u country code %u\n", | |
| rd, CTRY_DEFAULT); | |
| return -EINVAL; | |
| } | |
| band_2ghz = &sc->sbands[IEEE80211_BAND_2GHZ]; | |
| band_5ghz = &sc->sbands[IEEE80211_BAND_5GHZ]; | |
| chan_2ghz = sc->channels[IEEE80211_BAND_2GHZ]; | |
| chan_5ghz = sc->channels[IEEE80211_BAND_5GHZ]; | |
| for (i = 0; i < nchan; i++) { | |
| c = &ah->ah_channels[i]; | |
| if (IS_CHAN_2GHZ(c)) { | |
| chan_2ghz[a].band = IEEE80211_BAND_2GHZ; | |
| chan_2ghz[a].center_freq = c->channel; | |
| chan_2ghz[a].max_power = c->maxTxPower; | |
| if (c->privFlags & CHANNEL_DISALLOW_ADHOC) | |
| chan_2ghz[a].flags |= IEEE80211_CHAN_NO_IBSS; | |
| if (c->channelFlags & CHANNEL_PASSIVE) | |
| chan_2ghz[a].flags |= IEEE80211_CHAN_PASSIVE_SCAN; | |
| band_2ghz->n_channels = ++a; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "2MHz channel: %d, " | |
| "channelFlags: 0x%x\n", | |
| c->channel, c->channelFlags); | |
| } else if (IS_CHAN_5GHZ(c)) { | |
| chan_5ghz[b].band = IEEE80211_BAND_5GHZ; | |
| chan_5ghz[b].center_freq = c->channel; | |
| chan_5ghz[b].max_power = c->maxTxPower; | |
| if (c->privFlags & CHANNEL_DISALLOW_ADHOC) | |
| chan_5ghz[b].flags |= IEEE80211_CHAN_NO_IBSS; | |
| if (c->channelFlags & CHANNEL_PASSIVE) | |
| chan_5ghz[b].flags |= IEEE80211_CHAN_PASSIVE_SCAN; | |
| band_5ghz->n_channels = ++b; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "5MHz channel: %d, " | |
| "channelFlags: 0x%x\n", | |
| c->channel, c->channelFlags); | |
| } | |
| } | |
| return 0; | |
| } | |
| /* | |
| * Set/change channels. If the channel is really being changed, it's done | |
| * by reseting the chip. To accomplish this we must first cleanup any pending | |
| * DMA, then restart stuff. | |
| */ | |
| static int ath_set_channel(struct ath_softc *sc, struct ath9k_channel *hchan) | |
| { | |
| struct ath_hal *ah = sc->sc_ah; | |
| bool fastcc = true, stopped; | |
| if (sc->sc_flags & SC_OP_INVALID) | |
| return -EIO; | |
| if (hchan->channel != sc->sc_ah->ah_curchan->channel || | |
| hchan->channelFlags != sc->sc_ah->ah_curchan->channelFlags || | |
| (sc->sc_flags & SC_OP_CHAINMASK_UPDATE) || | |
| (sc->sc_flags & SC_OP_FULL_RESET)) { | |
| int status; | |
| /* | |
| * This is only performed if the channel settings have | |
| * actually changed. | |
| * | |
| * To switch channels clear any pending DMA operations; | |
| * wait long enough for the RX fifo to drain, reset the | |
| * hardware at the new frequency, and then re-enable | |
| * the relevant bits of the h/w. | |
| */ | |
| ath9k_hw_set_interrupts(ah, 0); | |
| ath_draintxq(sc, false); | |
| stopped = ath_stoprecv(sc); | |
| /* XXX: do not flush receive queue here. We don't want | |
| * to flush data frames already in queue because of | |
| * changing channel. */ | |
| if (!stopped || (sc->sc_flags & SC_OP_FULL_RESET)) | |
| fastcc = false; | |
| DPRINTF(sc, ATH_DBG_CONFIG, | |
| "(%u MHz) -> (%u MHz), cflags:%x, chanwidth: %d\n", | |
| sc->sc_ah->ah_curchan->channel, | |
| hchan->channel, hchan->channelFlags, sc->tx_chan_width); | |
| spin_lock_bh(&sc->sc_resetlock); | |
| if (!ath9k_hw_reset(ah, hchan, sc->tx_chan_width, | |
| sc->sc_tx_chainmask, sc->sc_rx_chainmask, | |
| sc->sc_ht_extprotspacing, fastcc, &status)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to reset channel %u (%uMhz) " | |
| "flags 0x%x hal status %u\n", | |
| ath9k_hw_mhz2ieee(ah, hchan->channel, | |
| hchan->channelFlags), | |
| hchan->channel, hchan->channelFlags, status); | |
| spin_unlock_bh(&sc->sc_resetlock); | |
| return -EIO; | |
| } | |
| spin_unlock_bh(&sc->sc_resetlock); | |
| sc->sc_flags &= ~SC_OP_CHAINMASK_UPDATE; | |
| sc->sc_flags &= ~SC_OP_FULL_RESET; | |
| if (ath_startrecv(sc) != 0) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to restart recv logic\n"); | |
| return -EIO; | |
| } | |
| ath_setcurmode(sc, ath_chan2mode(hchan)); | |
| ath_update_txpow(sc); | |
| ath9k_hw_set_interrupts(ah, sc->sc_imask); | |
| } | |
| return 0; | |
| } | |
| /* | |
| * This routine performs the periodic noise floor calibration function | |
| * that is used to adjust and optimize the chip performance. This | |
| * takes environmental changes (location, temperature) into account. | |
| * When the task is complete, it reschedules itself depending on the | |
| * appropriate interval that was calculated. | |
| */ | |
| static void ath_ani_calibrate(unsigned long data) | |
| { | |
| struct ath_softc *sc; | |
| struct ath_hal *ah; | |
| bool longcal = false; | |
| bool shortcal = false; | |
| bool aniflag = false; | |
| unsigned int timestamp = jiffies_to_msecs(jiffies); | |
| u32 cal_interval; | |
| sc = (struct ath_softc *)data; | |
| ah = sc->sc_ah; | |
| /* | |
| * don't calibrate when we're scanning. | |
| * we are most likely not on our home channel. | |
| */ | |
| if (sc->rx.rxfilter & FIF_BCN_PRBRESP_PROMISC) | |
| return; | |
| /* Long calibration runs independently of short calibration. */ | |
| if ((timestamp - sc->sc_ani.sc_longcal_timer) >= ATH_LONG_CALINTERVAL) { | |
| longcal = true; | |
| DPRINTF(sc, ATH_DBG_ANI, "longcal @%lu\n", jiffies); | |
| sc->sc_ani.sc_longcal_timer = timestamp; | |
| } | |
| /* Short calibration applies only while sc_caldone is false */ | |
| if (!sc->sc_ani.sc_caldone) { | |
| if ((timestamp - sc->sc_ani.sc_shortcal_timer) >= | |
| ATH_SHORT_CALINTERVAL) { | |
| shortcal = true; | |
| DPRINTF(sc, ATH_DBG_ANI, "shortcal @%lu\n", jiffies); | |
| sc->sc_ani.sc_shortcal_timer = timestamp; | |
| sc->sc_ani.sc_resetcal_timer = timestamp; | |
| } | |
| } else { | |
| if ((timestamp - sc->sc_ani.sc_resetcal_timer) >= | |
| ATH_RESTART_CALINTERVAL) { | |
| ath9k_hw_reset_calvalid(ah, ah->ah_curchan, | |
| &sc->sc_ani.sc_caldone); | |
| if (sc->sc_ani.sc_caldone) | |
| sc->sc_ani.sc_resetcal_timer = timestamp; | |
| } | |
| } | |
| /* Verify whether we must check ANI */ | |
| if ((timestamp - sc->sc_ani.sc_checkani_timer) >= | |
| ATH_ANI_POLLINTERVAL) { | |
| aniflag = true; | |
| sc->sc_ani.sc_checkani_timer = timestamp; | |
| } | |
| /* Skip all processing if there's nothing to do. */ | |
| if (longcal || shortcal || aniflag) { | |
| /* Call ANI routine if necessary */ | |
| if (aniflag) | |
| ath9k_hw_ani_monitor(ah, &sc->sc_halstats, | |
| ah->ah_curchan); | |
| /* Perform calibration if necessary */ | |
| if (longcal || shortcal) { | |
| bool iscaldone = false; | |
| if (ath9k_hw_calibrate(ah, ah->ah_curchan, | |
| sc->sc_rx_chainmask, longcal, | |
| &iscaldone)) { | |
| if (longcal) | |
| sc->sc_ani.sc_noise_floor = | |
| ath9k_hw_getchan_noise(ah, | |
| ah->ah_curchan); | |
| DPRINTF(sc, ATH_DBG_ANI, | |
| "calibrate chan %u/%x nf: %d\n", | |
| ah->ah_curchan->channel, | |
| ah->ah_curchan->channelFlags, | |
| sc->sc_ani.sc_noise_floor); | |
| } else { | |
| DPRINTF(sc, ATH_DBG_ANY, | |
| "calibrate chan %u/%x failed\n", | |
| ah->ah_curchan->channel, | |
| ah->ah_curchan->channelFlags); | |
| } | |
| sc->sc_ani.sc_caldone = iscaldone; | |
| } | |
| } | |
| /* | |
| * Set timer interval based on previous results. | |
| * The interval must be the shortest necessary to satisfy ANI, | |
| * short calibration and long calibration. | |
| */ | |
| cal_interval = ATH_LONG_CALINTERVAL; | |
| if (sc->sc_ah->ah_config.enable_ani) | |
| cal_interval = min(cal_interval, (u32)ATH_ANI_POLLINTERVAL); | |
| if (!sc->sc_ani.sc_caldone) | |
| cal_interval = min(cal_interval, (u32)ATH_SHORT_CALINTERVAL); | |
| mod_timer(&sc->sc_ani.timer, jiffies + msecs_to_jiffies(cal_interval)); | |
| } | |
| /* | |
| * Update tx/rx chainmask. For legacy association, | |
| * hard code chainmask to 1x1, for 11n association, use | |
| * the chainmask configuration. | |
| */ | |
| static void ath_update_chainmask(struct ath_softc *sc, int is_ht) | |
| { | |
| sc->sc_flags |= SC_OP_CHAINMASK_UPDATE; | |
| if (is_ht) { | |
| sc->sc_tx_chainmask = sc->sc_ah->ah_caps.tx_chainmask; | |
| sc->sc_rx_chainmask = sc->sc_ah->ah_caps.rx_chainmask; | |
| } else { | |
| sc->sc_tx_chainmask = 1; | |
| sc->sc_rx_chainmask = 1; | |
| } | |
| DPRINTF(sc, ATH_DBG_CONFIG, "tx chmask: %d, rx chmask: %d\n", | |
| sc->sc_tx_chainmask, sc->sc_rx_chainmask); | |
| } | |
| static void ath_node_attach(struct ath_softc *sc, struct ieee80211_sta *sta) | |
| { | |
| struct ath_node *an; | |
| an = (struct ath_node *)sta->drv_priv; | |
| if (sc->sc_flags & SC_OP_TXAGGR) | |
| ath_tx_node_init(sc, an); | |
| an->maxampdu = 1 << (IEEE80211_HTCAP_MAXRXAMPDU_FACTOR + | |
| sta->ht_cap.ampdu_factor); | |
| an->mpdudensity = parse_mpdudensity(sta->ht_cap.ampdu_density); | |
| } | |
| static void ath_node_detach(struct ath_softc *sc, struct ieee80211_sta *sta) | |
| { | |
| struct ath_node *an = (struct ath_node *)sta->drv_priv; | |
| if (sc->sc_flags & SC_OP_TXAGGR) | |
| ath_tx_node_cleanup(sc, an); | |
| } | |
| static void ath9k_tasklet(unsigned long data) | |
| { | |
| struct ath_softc *sc = (struct ath_softc *)data; | |
| u32 status = sc->sc_intrstatus; | |
| if (status & ATH9K_INT_FATAL) { | |
| /* need a chip reset */ | |
| ath_reset(sc, false); | |
| return; | |
| } else { | |
| if (status & | |
| (ATH9K_INT_RX | ATH9K_INT_RXEOL | ATH9K_INT_RXORN)) { | |
| spin_lock_bh(&sc->rx.rxflushlock); | |
| ath_rx_tasklet(sc, 0); | |
| spin_unlock_bh(&sc->rx.rxflushlock); | |
| } | |
| /* XXX: optimize this */ | |
| if (status & ATH9K_INT_TX) | |
| ath_tx_tasklet(sc); | |
| } | |
| /* re-enable hardware interrupt */ | |
| ath9k_hw_set_interrupts(sc->sc_ah, sc->sc_imask); | |
| } | |
| static irqreturn_t ath_isr(int irq, void *dev) | |
| { | |
| struct ath_softc *sc = dev; | |
| struct ath_hal *ah = sc->sc_ah; | |
| enum ath9k_int status; | |
| bool sched = false; | |
| do { | |
| if (sc->sc_flags & SC_OP_INVALID) { | |
| /* | |
| * The hardware is not ready/present, don't | |
| * touch anything. Note this can happen early | |
| * on if the IRQ is shared. | |
| */ | |
| return IRQ_NONE; | |
| } | |
| if (!ath9k_hw_intrpend(ah)) { /* shared irq, not for us */ | |
| return IRQ_NONE; | |
| } | |
| /* | |
| * Figure out the reason(s) for the interrupt. Note | |
| * that the hal returns a pseudo-ISR that may include | |
| * bits we haven't explicitly enabled so we mask the | |
| * value to insure we only process bits we requested. | |
| */ | |
| ath9k_hw_getisr(ah, &status); /* NB: clears ISR too */ | |
| status &= sc->sc_imask; /* discard unasked-for bits */ | |
| /* | |
| * If there are no status bits set, then this interrupt was not | |
| * for me (should have been caught above). | |
| */ | |
| if (!status) | |
| return IRQ_NONE; | |
| sc->sc_intrstatus = status; | |
| if (status & ATH9K_INT_FATAL) { | |
| /* need a chip reset */ | |
| sched = true; | |
| } else if (status & ATH9K_INT_RXORN) { | |
| /* need a chip reset */ | |
| sched = true; | |
| } else { | |
| if (status & ATH9K_INT_SWBA) { | |
| /* schedule a tasklet for beacon handling */ | |
| tasklet_schedule(&sc->bcon_tasklet); | |
| } | |
| if (status & ATH9K_INT_RXEOL) { | |
| /* | |
| * NB: the hardware should re-read the link when | |
| * RXE bit is written, but it doesn't work | |
| * at least on older hardware revs. | |
| */ | |
| sched = true; | |
| } | |
| if (status & ATH9K_INT_TXURN) | |
| /* bump tx trigger level */ | |
| ath9k_hw_updatetxtriglevel(ah, true); | |
| /* XXX: optimize this */ | |
| if (status & ATH9K_INT_RX) | |
| sched = true; | |
| if (status & ATH9K_INT_TX) | |
| sched = true; | |
| if (status & ATH9K_INT_BMISS) | |
| sched = true; | |
| /* carrier sense timeout */ | |
| if (status & ATH9K_INT_CST) | |
| sched = true; | |
| if (status & ATH9K_INT_MIB) { | |
| /* | |
| * Disable interrupts until we service the MIB | |
| * interrupt; otherwise it will continue to | |
| * fire. | |
| */ | |
| ath9k_hw_set_interrupts(ah, 0); | |
| /* | |
| * Let the hal handle the event. We assume | |
| * it will clear whatever condition caused | |
| * the interrupt. | |
| */ | |
| ath9k_hw_procmibevent(ah, &sc->sc_halstats); | |
| ath9k_hw_set_interrupts(ah, sc->sc_imask); | |
| } | |
| if (status & ATH9K_INT_TIM_TIMER) { | |
| if (!(ah->ah_caps.hw_caps & | |
| ATH9K_HW_CAP_AUTOSLEEP)) { | |
| /* Clear RxAbort bit so that we can | |
| * receive frames */ | |
| ath9k_hw_setrxabort(ah, 0); | |
| sched = true; | |
| } | |
| } | |
| } | |
| } while (0); | |
| ath_debug_stat_interrupt(sc, status); | |
| if (sched) { | |
| /* turn off every interrupt except SWBA */ | |
| ath9k_hw_set_interrupts(ah, (sc->sc_imask & ATH9K_INT_SWBA)); | |
| tasklet_schedule(&sc->intr_tq); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| static int ath_get_channel(struct ath_softc *sc, | |
| struct ieee80211_channel *chan) | |
| { | |
| int i; | |
| for (i = 0; i < sc->sc_ah->ah_nchan; i++) { | |
| if (sc->sc_ah->ah_channels[i].channel == chan->center_freq) | |
| return i; | |
| } | |
| return -1; | |
| } | |
| static u32 ath_get_extchanmode(struct ath_softc *sc, | |
| struct ieee80211_channel *chan, | |
| enum nl80211_channel_type channel_type) | |
| { | |
| u32 chanmode = 0; | |
| switch (chan->band) { | |
| case IEEE80211_BAND_2GHZ: | |
| switch(channel_type) { | |
| case NL80211_CHAN_NO_HT: | |
| case NL80211_CHAN_HT20: | |
| chanmode = CHANNEL_G_HT20; | |
| break; | |
| case NL80211_CHAN_HT40PLUS: | |
| chanmode = CHANNEL_G_HT40PLUS; | |
| break; | |
| case NL80211_CHAN_HT40MINUS: | |
| chanmode = CHANNEL_G_HT40MINUS; | |
| break; | |
| } | |
| break; | |
| case IEEE80211_BAND_5GHZ: | |
| switch(channel_type) { | |
| case NL80211_CHAN_NO_HT: | |
| case NL80211_CHAN_HT20: | |
| chanmode = CHANNEL_A_HT20; | |
| break; | |
| case NL80211_CHAN_HT40PLUS: | |
| chanmode = CHANNEL_A_HT40PLUS; | |
| break; | |
| case NL80211_CHAN_HT40MINUS: | |
| chanmode = CHANNEL_A_HT40MINUS; | |
| break; | |
| } | |
| break; | |
| default: | |
| break; | |
| } | |
| return chanmode; | |
| } | |
| static int ath_keyset(struct ath_softc *sc, u16 keyix, | |
| struct ath9k_keyval *hk, const u8 mac[ETH_ALEN]) | |
| { | |
| bool status; | |
| status = ath9k_hw_set_keycache_entry(sc->sc_ah, | |
| keyix, hk, mac, false); | |
| return status != false; | |
| } | |
| static int ath_setkey_tkip(struct ath_softc *sc, u16 keyix, const u8 *key, | |
| struct ath9k_keyval *hk, | |
| const u8 *addr) | |
| { | |
| const u8 *key_rxmic; | |
| const u8 *key_txmic; | |
| key_txmic = key + NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY; | |
| key_rxmic = key + NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY; | |
| if (addr == NULL) { | |
| /* Group key installation */ | |
| memcpy(hk->kv_mic, key_rxmic, sizeof(hk->kv_mic)); | |
| return ath_keyset(sc, keyix, hk, addr); | |
| } | |
| if (!sc->sc_splitmic) { | |
| /* | |
| * data key goes at first index, | |
| * the hal handles the MIC keys at index+64. | |
| */ | |
| memcpy(hk->kv_mic, key_rxmic, sizeof(hk->kv_mic)); | |
| memcpy(hk->kv_txmic, key_txmic, sizeof(hk->kv_txmic)); | |
| return ath_keyset(sc, keyix, hk, addr); | |
| } | |
| /* | |
| * TX key goes at first index, RX key at +32. | |
| * The hal handles the MIC keys at index+64. | |
| */ | |
| memcpy(hk->kv_mic, key_txmic, sizeof(hk->kv_mic)); | |
| if (!ath_keyset(sc, keyix, hk, NULL)) { | |
| /* Txmic entry failed. No need to proceed further */ | |
| DPRINTF(sc, ATH_DBG_KEYCACHE, | |
| "Setting TX MIC Key Failed\n"); | |
| return 0; | |
| } | |
| memcpy(hk->kv_mic, key_rxmic, sizeof(hk->kv_mic)); | |
| /* XXX delete tx key on failure? */ | |
| return ath_keyset(sc, keyix + 32, hk, addr); | |
| } | |
| static int ath_reserve_key_cache_slot_tkip(struct ath_softc *sc) | |
| { | |
| int i; | |
| for (i = IEEE80211_WEP_NKID; i < sc->sc_keymax / 2; i++) { | |
| if (test_bit(i, sc->sc_keymap) || | |
| test_bit(i + 64, sc->sc_keymap)) | |
| continue; /* At least one part of TKIP key allocated */ | |
| if (sc->sc_splitmic && | |
| (test_bit(i + 32, sc->sc_keymap) || | |
| test_bit(i + 64 + 32, sc->sc_keymap))) | |
| continue; /* At least one part of TKIP key allocated */ | |
| /* Found a free slot for a TKIP key */ | |
| return i; | |
| } | |
| return -1; | |
| } | |
| static int ath_reserve_key_cache_slot(struct ath_softc *sc) | |
| { | |
| int i; | |
| /* First, try to find slots that would not be available for TKIP. */ | |
| if (sc->sc_splitmic) { | |
| for (i = IEEE80211_WEP_NKID; i < sc->sc_keymax / 4; i++) { | |
| if (!test_bit(i, sc->sc_keymap) && | |
| (test_bit(i + 32, sc->sc_keymap) || | |
| test_bit(i + 64, sc->sc_keymap) || | |
| test_bit(i + 64 + 32, sc->sc_keymap))) | |
| return i; | |
| if (!test_bit(i + 32, sc->sc_keymap) && | |
| (test_bit(i, sc->sc_keymap) || | |
| test_bit(i + 64, sc->sc_keymap) || | |
| test_bit(i + 64 + 32, sc->sc_keymap))) | |
| return i + 32; | |
| if (!test_bit(i + 64, sc->sc_keymap) && | |
| (test_bit(i , sc->sc_keymap) || | |
| test_bit(i + 32, sc->sc_keymap) || | |
| test_bit(i + 64 + 32, sc->sc_keymap))) | |
| return i + 64; | |
| if (!test_bit(i + 64 + 32, sc->sc_keymap) && | |
| (test_bit(i, sc->sc_keymap) || | |
| test_bit(i + 32, sc->sc_keymap) || | |
| test_bit(i + 64, sc->sc_keymap))) | |
| return i + 64 + 32; | |
| } | |
| } else { | |
| for (i = IEEE80211_WEP_NKID; i < sc->sc_keymax / 2; i++) { | |
| if (!test_bit(i, sc->sc_keymap) && | |
| test_bit(i + 64, sc->sc_keymap)) | |
| return i; | |
| if (test_bit(i, sc->sc_keymap) && | |
| !test_bit(i + 64, sc->sc_keymap)) | |
| return i + 64; | |
| } | |
| } | |
| /* No partially used TKIP slots, pick any available slot */ | |
| for (i = IEEE80211_WEP_NKID; i < sc->sc_keymax; i++) { | |
| /* Do not allow slots that could be needed for TKIP group keys | |
| * to be used. This limitation could be removed if we know that | |
| * TKIP will not be used. */ | |
| if (i >= 64 && i < 64 + IEEE80211_WEP_NKID) | |
| continue; | |
| if (sc->sc_splitmic) { | |
| if (i >= 32 && i < 32 + IEEE80211_WEP_NKID) | |
| continue; | |
| if (i >= 64 + 32 && i < 64 + 32 + IEEE80211_WEP_NKID) | |
| continue; | |
| } | |
| if (!test_bit(i, sc->sc_keymap)) | |
| return i; /* Found a free slot for a key */ | |
| } | |
| /* No free slot found */ | |
| return -1; | |
| } | |
| static int ath_key_config(struct ath_softc *sc, | |
| const u8 *addr, | |
| struct ieee80211_key_conf *key) | |
| { | |
| struct ath9k_keyval hk; | |
| const u8 *mac = NULL; | |
| int ret = 0; | |
| int idx; | |
| memset(&hk, 0, sizeof(hk)); | |
| switch (key->alg) { | |
| case ALG_WEP: | |
| hk.kv_type = ATH9K_CIPHER_WEP; | |
| break; | |
| case ALG_TKIP: | |
| hk.kv_type = ATH9K_CIPHER_TKIP; | |
| break; | |
| case ALG_CCMP: | |
| hk.kv_type = ATH9K_CIPHER_AES_CCM; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| hk.kv_len = key->keylen; | |
| memcpy(hk.kv_val, key->key, key->keylen); | |
| if (!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)) { | |
| /* For now, use the default keys for broadcast keys. This may | |
| * need to change with virtual interfaces. */ | |
| idx = key->keyidx; | |
| } else if (key->keyidx) { | |
| struct ieee80211_vif *vif; | |
| mac = addr; | |
| vif = sc->sc_vaps[0]; | |
| if (vif->type != NL80211_IFTYPE_AP) { | |
| /* Only keyidx 0 should be used with unicast key, but | |
| * allow this for client mode for now. */ | |
| idx = key->keyidx; | |
| } else | |
| return -EIO; | |
| } else { | |
| mac = addr; | |
| if (key->alg == ALG_TKIP) | |
| idx = ath_reserve_key_cache_slot_tkip(sc); | |
| else | |
| idx = ath_reserve_key_cache_slot(sc); | |
| if (idx < 0) | |
| return -EIO; /* no free key cache entries */ | |
| } | |
| if (key->alg == ALG_TKIP) | |
| ret = ath_setkey_tkip(sc, idx, key->key, &hk, mac); | |
| else | |
| ret = ath_keyset(sc, idx, &hk, mac); | |
| if (!ret) | |
| return -EIO; | |
| set_bit(idx, sc->sc_keymap); | |
| if (key->alg == ALG_TKIP) { | |
| set_bit(idx + 64, sc->sc_keymap); | |
| if (sc->sc_splitmic) { | |
| set_bit(idx + 32, sc->sc_keymap); | |
| set_bit(idx + 64 + 32, sc->sc_keymap); | |
| } | |
| } | |
| return idx; | |
| } | |
| static void ath_key_delete(struct ath_softc *sc, struct ieee80211_key_conf *key) | |
| { | |
| ath9k_hw_keyreset(sc->sc_ah, key->hw_key_idx); | |
| if (key->hw_key_idx < IEEE80211_WEP_NKID) | |
| return; | |
| clear_bit(key->hw_key_idx, sc->sc_keymap); | |
| if (key->alg != ALG_TKIP) | |
| return; | |
| clear_bit(key->hw_key_idx + 64, sc->sc_keymap); | |
| if (sc->sc_splitmic) { | |
| clear_bit(key->hw_key_idx + 32, sc->sc_keymap); | |
| clear_bit(key->hw_key_idx + 64 + 32, sc->sc_keymap); | |
| } | |
| } | |
| static void setup_ht_cap(struct ieee80211_sta_ht_cap *ht_info) | |
| { | |
| #define ATH9K_HT_CAP_MAXRXAMPDU_65536 0x3 /* 2 ^ 16 */ | |
| #define ATH9K_HT_CAP_MPDUDENSITY_8 0x6 /* 8 usec */ | |
| ht_info->ht_supported = true; | |
| ht_info->cap = IEEE80211_HT_CAP_SUP_WIDTH_20_40 | | |
| IEEE80211_HT_CAP_SM_PS | | |
| IEEE80211_HT_CAP_SGI_40 | | |
| IEEE80211_HT_CAP_DSSSCCK40; | |
| ht_info->ampdu_factor = ATH9K_HT_CAP_MAXRXAMPDU_65536; | |
| ht_info->ampdu_density = ATH9K_HT_CAP_MPDUDENSITY_8; | |
| /* set up supported mcs set */ | |
| memset(&ht_info->mcs, 0, sizeof(ht_info->mcs)); | |
| ht_info->mcs.rx_mask[0] = 0xff; | |
| ht_info->mcs.rx_mask[1] = 0xff; | |
| ht_info->mcs.tx_params = IEEE80211_HT_MCS_TX_DEFINED; | |
| } | |
| static void ath9k_bss_assoc_info(struct ath_softc *sc, | |
| struct ieee80211_vif *vif, | |
| struct ieee80211_bss_conf *bss_conf) | |
| { | |
| struct ath_vap *avp = (void *)vif->drv_priv; | |
| if (bss_conf->assoc) { | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Bss Info ASSOC %d, bssid: %pM\n", | |
| bss_conf->aid, sc->sc_curbssid); | |
| /* New association, store aid */ | |
| if (avp->av_opmode == NL80211_IFTYPE_STATION) { | |
| sc->sc_curaid = bss_conf->aid; | |
| ath9k_hw_write_associd(sc->sc_ah, sc->sc_curbssid, | |
| sc->sc_curaid); | |
| } | |
| /* Configure the beacon */ | |
| ath_beacon_config(sc, 0); | |
| sc->sc_flags |= SC_OP_BEACONS; | |
| /* Reset rssi stats */ | |
| sc->sc_halstats.ns_avgbrssi = ATH_RSSI_DUMMY_MARKER; | |
| sc->sc_halstats.ns_avgrssi = ATH_RSSI_DUMMY_MARKER; | |
| sc->sc_halstats.ns_avgtxrssi = ATH_RSSI_DUMMY_MARKER; | |
| sc->sc_halstats.ns_avgtxrate = ATH_RATE_DUMMY_MARKER; | |
| /* Start ANI */ | |
| mod_timer(&sc->sc_ani.timer, | |
| jiffies + msecs_to_jiffies(ATH_ANI_POLLINTERVAL)); | |
| } else { | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Bss Info DISSOC\n"); | |
| sc->sc_curaid = 0; | |
| } | |
| } | |
| /********************************/ | |
| /* LED functions */ | |
| /********************************/ | |
| static void ath_led_brightness(struct led_classdev *led_cdev, | |
| enum led_brightness brightness) | |
| { | |
| struct ath_led *led = container_of(led_cdev, struct ath_led, led_cdev); | |
| struct ath_softc *sc = led->sc; | |
| switch (brightness) { | |
| case LED_OFF: | |
| if (led->led_type == ATH_LED_ASSOC || | |
| led->led_type == ATH_LED_RADIO) | |
| sc->sc_flags &= ~SC_OP_LED_ASSOCIATED; | |
| ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, | |
| (led->led_type == ATH_LED_RADIO) ? 1 : | |
| !!(sc->sc_flags & SC_OP_LED_ASSOCIATED)); | |
| break; | |
| case LED_FULL: | |
| if (led->led_type == ATH_LED_ASSOC) | |
| sc->sc_flags |= SC_OP_LED_ASSOCIATED; | |
| ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 0); | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| static int ath_register_led(struct ath_softc *sc, struct ath_led *led, | |
| char *trigger) | |
| { | |
| int ret; | |
| led->sc = sc; | |
| led->led_cdev.name = led->name; | |
| led->led_cdev.default_trigger = trigger; | |
| led->led_cdev.brightness_set = ath_led_brightness; | |
| ret = led_classdev_register(wiphy_dev(sc->hw->wiphy), &led->led_cdev); | |
| if (ret) | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Failed to register led:%s", led->name); | |
| else | |
| led->registered = 1; | |
| return ret; | |
| } | |
| static void ath_unregister_led(struct ath_led *led) | |
| { | |
| if (led->registered) { | |
| led_classdev_unregister(&led->led_cdev); | |
| led->registered = 0; | |
| } | |
| } | |
| static void ath_deinit_leds(struct ath_softc *sc) | |
| { | |
| ath_unregister_led(&sc->assoc_led); | |
| sc->sc_flags &= ~SC_OP_LED_ASSOCIATED; | |
| ath_unregister_led(&sc->tx_led); | |
| ath_unregister_led(&sc->rx_led); | |
| ath_unregister_led(&sc->radio_led); | |
| ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1); | |
| } | |
| static void ath_init_leds(struct ath_softc *sc) | |
| { | |
| char *trigger; | |
| int ret; | |
| /* Configure gpio 1 for output */ | |
| ath9k_hw_cfg_output(sc->sc_ah, ATH_LED_PIN, | |
| AR_GPIO_OUTPUT_MUX_AS_OUTPUT); | |
| /* LED off, active low */ | |
| ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1); | |
| trigger = ieee80211_get_radio_led_name(sc->hw); | |
| snprintf(sc->radio_led.name, sizeof(sc->radio_led.name), | |
| "ath9k-%s:radio", wiphy_name(sc->hw->wiphy)); | |
| ret = ath_register_led(sc, &sc->radio_led, trigger); | |
| sc->radio_led.led_type = ATH_LED_RADIO; | |
| if (ret) | |
| goto fail; | |
| trigger = ieee80211_get_assoc_led_name(sc->hw); | |
| snprintf(sc->assoc_led.name, sizeof(sc->assoc_led.name), | |
| "ath9k-%s:assoc", wiphy_name(sc->hw->wiphy)); | |
| ret = ath_register_led(sc, &sc->assoc_led, trigger); | |
| sc->assoc_led.led_type = ATH_LED_ASSOC; | |
| if (ret) | |
| goto fail; | |
| trigger = ieee80211_get_tx_led_name(sc->hw); | |
| snprintf(sc->tx_led.name, sizeof(sc->tx_led.name), | |
| "ath9k-%s:tx", wiphy_name(sc->hw->wiphy)); | |
| ret = ath_register_led(sc, &sc->tx_led, trigger); | |
| sc->tx_led.led_type = ATH_LED_TX; | |
| if (ret) | |
| goto fail; | |
| trigger = ieee80211_get_rx_led_name(sc->hw); | |
| snprintf(sc->rx_led.name, sizeof(sc->rx_led.name), | |
| "ath9k-%s:rx", wiphy_name(sc->hw->wiphy)); | |
| ret = ath_register_led(sc, &sc->rx_led, trigger); | |
| sc->rx_led.led_type = ATH_LED_RX; | |
| if (ret) | |
| goto fail; | |
| return; | |
| fail: | |
| ath_deinit_leds(sc); | |
| } | |
| #if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE) | |
| /*******************/ | |
| /* Rfkill */ | |
| /*******************/ | |
| static void ath_radio_enable(struct ath_softc *sc) | |
| { | |
| struct ath_hal *ah = sc->sc_ah; | |
| int status; | |
| spin_lock_bh(&sc->sc_resetlock); | |
| if (!ath9k_hw_reset(ah, ah->ah_curchan, | |
| sc->tx_chan_width, | |
| sc->sc_tx_chainmask, | |
| sc->sc_rx_chainmask, | |
| sc->sc_ht_extprotspacing, | |
| false, &status)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to reset channel %u (%uMhz) " | |
| "flags 0x%x hal status %u\n", | |
| ath9k_hw_mhz2ieee(ah, | |
| ah->ah_curchan->channel, | |
| ah->ah_curchan->channelFlags), | |
| ah->ah_curchan->channel, | |
| ah->ah_curchan->channelFlags, status); | |
| } | |
| spin_unlock_bh(&sc->sc_resetlock); | |
| ath_update_txpow(sc); | |
| if (ath_startrecv(sc) != 0) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to restart recv logic\n"); | |
| return; | |
| } | |
| if (sc->sc_flags & SC_OP_BEACONS) | |
| ath_beacon_config(sc, ATH_IF_ID_ANY); /* restart beacons */ | |
| /* Re-Enable interrupts */ | |
| ath9k_hw_set_interrupts(ah, sc->sc_imask); | |
| /* Enable LED */ | |
| ath9k_hw_cfg_output(ah, ATH_LED_PIN, | |
| AR_GPIO_OUTPUT_MUX_AS_OUTPUT); | |
| ath9k_hw_set_gpio(ah, ATH_LED_PIN, 0); | |
| ieee80211_wake_queues(sc->hw); | |
| } | |
| static void ath_radio_disable(struct ath_softc *sc) | |
| { | |
| struct ath_hal *ah = sc->sc_ah; | |
| int status; | |
| ieee80211_stop_queues(sc->hw); | |
| /* Disable LED */ | |
| ath9k_hw_set_gpio(ah, ATH_LED_PIN, 1); | |
| ath9k_hw_cfg_gpio_input(ah, ATH_LED_PIN); | |
| /* Disable interrupts */ | |
| ath9k_hw_set_interrupts(ah, 0); | |
| ath_draintxq(sc, false); /* clear pending tx frames */ | |
| ath_stoprecv(sc); /* turn off frame recv */ | |
| ath_flushrecv(sc); /* flush recv queue */ | |
| spin_lock_bh(&sc->sc_resetlock); | |
| if (!ath9k_hw_reset(ah, ah->ah_curchan, | |
| sc->tx_chan_width, | |
| sc->sc_tx_chainmask, | |
| sc->sc_rx_chainmask, | |
| sc->sc_ht_extprotspacing, | |
| false, &status)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to reset channel %u (%uMhz) " | |
| "flags 0x%x hal status %u\n", | |
| ath9k_hw_mhz2ieee(ah, | |
| ah->ah_curchan->channel, | |
| ah->ah_curchan->channelFlags), | |
| ah->ah_curchan->channel, | |
| ah->ah_curchan->channelFlags, status); | |
| } | |
| spin_unlock_bh(&sc->sc_resetlock); | |
| ath9k_hw_phy_disable(ah); | |
| ath9k_hw_setpower(ah, ATH9K_PM_FULL_SLEEP); | |
| } | |
| static bool ath_is_rfkill_set(struct ath_softc *sc) | |
| { | |
| struct ath_hal *ah = sc->sc_ah; | |
| return ath9k_hw_gpio_get(ah, ah->ah_rfkill_gpio) == | |
| ah->ah_rfkill_polarity; | |
| } | |
| /* h/w rfkill poll function */ | |
| static void ath_rfkill_poll(struct work_struct *work) | |
| { | |
| struct ath_softc *sc = container_of(work, struct ath_softc, | |
| rf_kill.rfkill_poll.work); | |
| bool radio_on; | |
| if (sc->sc_flags & SC_OP_INVALID) | |
| return; | |
| radio_on = !ath_is_rfkill_set(sc); | |
| /* | |
| * enable/disable radio only when there is a | |
| * state change in RF switch | |
| */ | |
| if (radio_on == !!(sc->sc_flags & SC_OP_RFKILL_HW_BLOCKED)) { | |
| enum rfkill_state state; | |
| if (sc->sc_flags & SC_OP_RFKILL_SW_BLOCKED) { | |
| state = radio_on ? RFKILL_STATE_SOFT_BLOCKED | |
| : RFKILL_STATE_HARD_BLOCKED; | |
| } else if (radio_on) { | |
| ath_radio_enable(sc); | |
| state = RFKILL_STATE_UNBLOCKED; | |
| } else { | |
| ath_radio_disable(sc); | |
| state = RFKILL_STATE_HARD_BLOCKED; | |
| } | |
| if (state == RFKILL_STATE_HARD_BLOCKED) | |
| sc->sc_flags |= SC_OP_RFKILL_HW_BLOCKED; | |
| else | |
| sc->sc_flags &= ~SC_OP_RFKILL_HW_BLOCKED; | |
| rfkill_force_state(sc->rf_kill.rfkill, state); | |
| } | |
| queue_delayed_work(sc->hw->workqueue, &sc->rf_kill.rfkill_poll, | |
| msecs_to_jiffies(ATH_RFKILL_POLL_INTERVAL)); | |
| } | |
| /* s/w rfkill handler */ | |
| static int ath_sw_toggle_radio(void *data, enum rfkill_state state) | |
| { | |
| struct ath_softc *sc = data; | |
| switch (state) { | |
| case RFKILL_STATE_SOFT_BLOCKED: | |
| if (!(sc->sc_flags & (SC_OP_RFKILL_HW_BLOCKED | | |
| SC_OP_RFKILL_SW_BLOCKED))) | |
| ath_radio_disable(sc); | |
| sc->sc_flags |= SC_OP_RFKILL_SW_BLOCKED; | |
| return 0; | |
| case RFKILL_STATE_UNBLOCKED: | |
| if ((sc->sc_flags & SC_OP_RFKILL_SW_BLOCKED)) { | |
| sc->sc_flags &= ~SC_OP_RFKILL_SW_BLOCKED; | |
| if (sc->sc_flags & SC_OP_RFKILL_HW_BLOCKED) { | |
| DPRINTF(sc, ATH_DBG_FATAL, "Can't turn on the" | |
| "radio as it is disabled by h/w\n"); | |
| return -EPERM; | |
| } | |
| ath_radio_enable(sc); | |
| } | |
| return 0; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| /* Init s/w rfkill */ | |
| static int ath_init_sw_rfkill(struct ath_softc *sc) | |
| { | |
| sc->rf_kill.rfkill = rfkill_allocate(wiphy_dev(sc->hw->wiphy), | |
| RFKILL_TYPE_WLAN); | |
| if (!sc->rf_kill.rfkill) { | |
| DPRINTF(sc, ATH_DBG_FATAL, "Failed to allocate rfkill\n"); | |
| return -ENOMEM; | |
| } | |
| snprintf(sc->rf_kill.rfkill_name, sizeof(sc->rf_kill.rfkill_name), | |
| "ath9k-%s:rfkill", wiphy_name(sc->hw->wiphy)); | |
| sc->rf_kill.rfkill->name = sc->rf_kill.rfkill_name; | |
| sc->rf_kill.rfkill->data = sc; | |
| sc->rf_kill.rfkill->toggle_radio = ath_sw_toggle_radio; | |
| sc->rf_kill.rfkill->state = RFKILL_STATE_UNBLOCKED; | |
| sc->rf_kill.rfkill->user_claim_unsupported = 1; | |
| return 0; | |
| } | |
| /* Deinitialize rfkill */ | |
| static void ath_deinit_rfkill(struct ath_softc *sc) | |
| { | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT) | |
| cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll); | |
| if (sc->sc_flags & SC_OP_RFKILL_REGISTERED) { | |
| rfkill_unregister(sc->rf_kill.rfkill); | |
| sc->sc_flags &= ~SC_OP_RFKILL_REGISTERED; | |
| sc->rf_kill.rfkill = NULL; | |
| } | |
| } | |
| static int ath_start_rfkill_poll(struct ath_softc *sc) | |
| { | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT) | |
| queue_delayed_work(sc->hw->workqueue, | |
| &sc->rf_kill.rfkill_poll, 0); | |
| if (!(sc->sc_flags & SC_OP_RFKILL_REGISTERED)) { | |
| if (rfkill_register(sc->rf_kill.rfkill)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to register rfkill\n"); | |
| rfkill_free(sc->rf_kill.rfkill); | |
| /* Deinitialize the device */ | |
| ath_detach(sc); | |
| if (sc->pdev->irq) | |
| free_irq(sc->pdev->irq, sc); | |
| pci_iounmap(sc->pdev, sc->mem); | |
| pci_release_region(sc->pdev, 0); | |
| pci_disable_device(sc->pdev); | |
| ieee80211_free_hw(sc->hw); | |
| return -EIO; | |
| } else { | |
| sc->sc_flags |= SC_OP_RFKILL_REGISTERED; | |
| } | |
| } | |
| return 0; | |
| } | |
| #endif /* CONFIG_RFKILL */ | |
| static void ath_detach(struct ath_softc *sc) | |
| { | |
| struct ieee80211_hw *hw = sc->hw; | |
| int i = 0; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Detach ATH hw\n"); | |
| #if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE) | |
| ath_deinit_rfkill(sc); | |
| #endif | |
| ath_deinit_leds(sc); | |
| ieee80211_unregister_hw(hw); | |
| ath_rx_cleanup(sc); | |
| ath_tx_cleanup(sc); | |
| tasklet_kill(&sc->intr_tq); | |
| tasklet_kill(&sc->bcon_tasklet); | |
| if (!(sc->sc_flags & SC_OP_INVALID)) | |
| ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_AWAKE); | |
| /* cleanup tx queues */ | |
| for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) | |
| if (ATH_TXQ_SETUP(sc, i)) | |
| ath_tx_cleanupq(sc, &sc->tx.txq[i]); | |
| ath9k_hw_detach(sc->sc_ah); | |
| ath9k_exit_debug(sc); | |
| } | |
| static int ath_init(u16 devid, struct ath_softc *sc) | |
| { | |
| struct ath_hal *ah = NULL; | |
| int status; | |
| int error = 0, i; | |
| int csz = 0; | |
| /* XXX: hardware will not be ready until ath_open() being called */ | |
| sc->sc_flags |= SC_OP_INVALID; | |
| if (ath9k_init_debug(sc) < 0) | |
| printk(KERN_ERR "Unable to create debugfs files\n"); | |
| spin_lock_init(&sc->sc_resetlock); | |
| mutex_init(&sc->mutex); | |
| tasklet_init(&sc->intr_tq, ath9k_tasklet, (unsigned long)sc); | |
| tasklet_init(&sc->bcon_tasklet, ath9k_beacon_tasklet, | |
| (unsigned long)sc); | |
| /* | |
| * Cache line size is used to size and align various | |
| * structures used to communicate with the hardware. | |
| */ | |
| bus_read_cachesize(sc, &csz); | |
| /* XXX assert csz is non-zero */ | |
| sc->sc_cachelsz = csz << 2; /* convert to bytes */ | |
| ah = ath9k_hw_attach(devid, sc, sc->mem, &status); | |
| if (ah == NULL) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to attach hardware; HAL status %u\n", status); | |
| error = -ENXIO; | |
| goto bad; | |
| } | |
| sc->sc_ah = ah; | |
| /* Get the hardware key cache size. */ | |
| sc->sc_keymax = ah->ah_caps.keycache_size; | |
| if (sc->sc_keymax > ATH_KEYMAX) { | |
| DPRINTF(sc, ATH_DBG_KEYCACHE, | |
| "Warning, using only %u entries in %u key cache\n", | |
| ATH_KEYMAX, sc->sc_keymax); | |
| sc->sc_keymax = ATH_KEYMAX; | |
| } | |
| /* | |
| * Reset the key cache since some parts do not | |
| * reset the contents on initial power up. | |
| */ | |
| for (i = 0; i < sc->sc_keymax; i++) | |
| ath9k_hw_keyreset(ah, (u16) i); | |
| /* Collect the channel list using the default country code */ | |
| error = ath_setup_channels(sc); | |
| if (error) | |
| goto bad; | |
| /* default to MONITOR mode */ | |
| sc->sc_ah->ah_opmode = NL80211_IFTYPE_MONITOR; | |
| /* Setup rate tables */ | |
| ath_rate_attach(sc); | |
| ath_setup_rates(sc, IEEE80211_BAND_2GHZ); | |
| ath_setup_rates(sc, IEEE80211_BAND_5GHZ); | |
| /* | |
| * Allocate hardware transmit queues: one queue for | |
| * beacon frames and one data queue for each QoS | |
| * priority. Note that the hal handles reseting | |
| * these queues at the needed time. | |
| */ | |
| sc->beacon.beaconq = ath_beaconq_setup(ah); | |
| if (sc->beacon.beaconq == -1) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to setup a beacon xmit queue\n"); | |
| error = -EIO; | |
| goto bad2; | |
| } | |
| sc->beacon.cabq = ath_txq_setup(sc, ATH9K_TX_QUEUE_CAB, 0); | |
| if (sc->beacon.cabq == NULL) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to setup CAB xmit queue\n"); | |
| error = -EIO; | |
| goto bad2; | |
| } | |
| sc->sc_config.cabqReadytime = ATH_CABQ_READY_TIME; | |
| ath_cabq_update(sc); | |
| for (i = 0; i < ARRAY_SIZE(sc->tx.hwq_map); i++) | |
| sc->tx.hwq_map[i] = -1; | |
| /* Setup data queues */ | |
| /* NB: ensure BK queue is the lowest priority h/w queue */ | |
| if (!ath_tx_setup(sc, ATH9K_WME_AC_BK)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to setup xmit queue for BK traffic\n"); | |
| error = -EIO; | |
| goto bad2; | |
| } | |
| if (!ath_tx_setup(sc, ATH9K_WME_AC_BE)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to setup xmit queue for BE traffic\n"); | |
| error = -EIO; | |
| goto bad2; | |
| } | |
| if (!ath_tx_setup(sc, ATH9K_WME_AC_VI)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to setup xmit queue for VI traffic\n"); | |
| error = -EIO; | |
| goto bad2; | |
| } | |
| if (!ath_tx_setup(sc, ATH9K_WME_AC_VO)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to setup xmit queue for VO traffic\n"); | |
| error = -EIO; | |
| goto bad2; | |
| } | |
| /* Initializes the noise floor to a reasonable default value. | |
| * Later on this will be updated during ANI processing. */ | |
| sc->sc_ani.sc_noise_floor = ATH_DEFAULT_NOISE_FLOOR; | |
| setup_timer(&sc->sc_ani.timer, ath_ani_calibrate, (unsigned long)sc); | |
| if (ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER, | |
| ATH9K_CIPHER_TKIP, NULL)) { | |
| /* | |
| * Whether we should enable h/w TKIP MIC. | |
| * XXX: if we don't support WME TKIP MIC, then we wouldn't | |
| * report WMM capable, so it's always safe to turn on | |
| * TKIP MIC in this case. | |
| */ | |
| ath9k_hw_setcapability(sc->sc_ah, ATH9K_CAP_TKIP_MIC, | |
| 0, 1, NULL); | |
| } | |
| /* | |
| * Check whether the separate key cache entries | |
| * are required to handle both tx+rx MIC keys. | |
| * With split mic keys the number of stations is limited | |
| * to 27 otherwise 59. | |
| */ | |
| if (ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER, | |
| ATH9K_CIPHER_TKIP, NULL) | |
| && ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER, | |
| ATH9K_CIPHER_MIC, NULL) | |
| && ath9k_hw_getcapability(ah, ATH9K_CAP_TKIP_SPLIT, | |
| 0, NULL)) | |
| sc->sc_splitmic = 1; | |
| /* turn on mcast key search if possible */ | |
| if (!ath9k_hw_getcapability(ah, ATH9K_CAP_MCAST_KEYSRCH, 0, NULL)) | |
| (void)ath9k_hw_setcapability(ah, ATH9K_CAP_MCAST_KEYSRCH, 1, | |
| 1, NULL); | |
| sc->sc_config.txpowlimit = ATH_TXPOWER_MAX; | |
| sc->sc_config.txpowlimit_override = 0; | |
| /* 11n Capabilities */ | |
| if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT) { | |
| sc->sc_flags |= SC_OP_TXAGGR; | |
| sc->sc_flags |= SC_OP_RXAGGR; | |
| } | |
| sc->sc_tx_chainmask = ah->ah_caps.tx_chainmask; | |
| sc->sc_rx_chainmask = ah->ah_caps.rx_chainmask; | |
| ath9k_hw_setcapability(ah, ATH9K_CAP_DIVERSITY, 1, true, NULL); | |
| sc->rx.defant = ath9k_hw_getdefantenna(ah); | |
| ath9k_hw_getmac(ah, sc->sc_myaddr); | |
| if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_BSSIDMASK) { | |
| ath9k_hw_getbssidmask(ah, sc->sc_bssidmask); | |
| ATH_SET_VAP_BSSID_MASK(sc->sc_bssidmask); | |
| ath9k_hw_setbssidmask(ah, sc->sc_bssidmask); | |
| } | |
| sc->beacon.slottime = ATH9K_SLOT_TIME_9; /* default to short slot time */ | |
| /* initialize beacon slots */ | |
| for (i = 0; i < ARRAY_SIZE(sc->beacon.bslot); i++) | |
| sc->beacon.bslot[i] = ATH_IF_ID_ANY; | |
| /* save MISC configurations */ | |
| sc->sc_config.swBeaconProcess = 1; | |
| /* setup channels and rates */ | |
| sc->sbands[IEEE80211_BAND_2GHZ].channels = | |
| sc->channels[IEEE80211_BAND_2GHZ]; | |
| sc->sbands[IEEE80211_BAND_2GHZ].bitrates = | |
| sc->rates[IEEE80211_BAND_2GHZ]; | |
| sc->sbands[IEEE80211_BAND_2GHZ].band = IEEE80211_BAND_2GHZ; | |
| if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes)) { | |
| sc->sbands[IEEE80211_BAND_5GHZ].channels = | |
| sc->channels[IEEE80211_BAND_5GHZ]; | |
| sc->sbands[IEEE80211_BAND_5GHZ].bitrates = | |
| sc->rates[IEEE80211_BAND_5GHZ]; | |
| sc->sbands[IEEE80211_BAND_5GHZ].band = IEEE80211_BAND_5GHZ; | |
| } | |
| return 0; | |
| bad2: | |
| /* cleanup tx queues */ | |
| for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) | |
| if (ATH_TXQ_SETUP(sc, i)) | |
| ath_tx_cleanupq(sc, &sc->tx.txq[i]); | |
| bad: | |
| if (ah) | |
| ath9k_hw_detach(ah); | |
| ath9k_exit_debug(sc); | |
| return error; | |
| } | |
| static int ath_attach(u16 devid, struct ath_softc *sc) | |
| { | |
| struct ieee80211_hw *hw = sc->hw; | |
| int error = 0, i; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Attach ATH hw\n"); | |
| error = ath_init(devid, sc); | |
| if (error != 0) | |
| return error; | |
| /* get mac address from hardware and set in mac80211 */ | |
| SET_IEEE80211_PERM_ADDR(hw, sc->sc_myaddr); | |
| hw->flags = IEEE80211_HW_RX_INCLUDES_FCS | | |
| IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING | | |
| IEEE80211_HW_SIGNAL_DBM | | |
| IEEE80211_HW_AMPDU_AGGREGATION; | |
| hw->wiphy->interface_modes = | |
| BIT(NL80211_IFTYPE_AP) | | |
| BIT(NL80211_IFTYPE_STATION) | | |
| BIT(NL80211_IFTYPE_ADHOC); | |
| hw->queues = 4; | |
| hw->max_rates = 4; | |
| hw->max_rate_tries = ATH_11N_TXMAXTRY; | |
| hw->sta_data_size = sizeof(struct ath_node); | |
| hw->vif_data_size = sizeof(struct ath_vap); | |
| hw->rate_control_algorithm = "ath9k_rate_control"; | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT) { | |
| setup_ht_cap(&sc->sbands[IEEE80211_BAND_2GHZ].ht_cap); | |
| if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes)) | |
| setup_ht_cap(&sc->sbands[IEEE80211_BAND_5GHZ].ht_cap); | |
| } | |
| hw->wiphy->bands[IEEE80211_BAND_2GHZ] = &sc->sbands[IEEE80211_BAND_2GHZ]; | |
| if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes)) | |
| hw->wiphy->bands[IEEE80211_BAND_5GHZ] = | |
| &sc->sbands[IEEE80211_BAND_5GHZ]; | |
| /* initialize tx/rx engine */ | |
| error = ath_tx_init(sc, ATH_TXBUF); | |
| if (error != 0) | |
| goto error_attach; | |
| error = ath_rx_init(sc, ATH_RXBUF); | |
| if (error != 0) | |
| goto error_attach; | |
| #if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE) | |
| /* Initialze h/w Rfkill */ | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT) | |
| INIT_DELAYED_WORK(&sc->rf_kill.rfkill_poll, ath_rfkill_poll); | |
| /* Initialize s/w rfkill */ | |
| error = ath_init_sw_rfkill(sc); | |
| if (error) | |
| goto error_attach; | |
| #endif | |
| error = ieee80211_register_hw(hw); | |
| /* Initialize LED control */ | |
| ath_init_leds(sc); | |
| return 0; | |
| error_attach: | |
| /* cleanup tx queues */ | |
| for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) | |
| if (ATH_TXQ_SETUP(sc, i)) | |
| ath_tx_cleanupq(sc, &sc->tx.txq[i]); | |
| ath9k_hw_detach(sc->sc_ah); | |
| ath9k_exit_debug(sc); | |
| return error; | |
| } | |
| int ath_reset(struct ath_softc *sc, bool retry_tx) | |
| { | |
| struct ath_hal *ah = sc->sc_ah; | |
| int status; | |
| int error = 0; | |
| ath9k_hw_set_interrupts(ah, 0); | |
| ath_draintxq(sc, retry_tx); | |
| ath_stoprecv(sc); | |
| ath_flushrecv(sc); | |
| spin_lock_bh(&sc->sc_resetlock); | |
| if (!ath9k_hw_reset(ah, sc->sc_ah->ah_curchan, | |
| sc->tx_chan_width, | |
| sc->sc_tx_chainmask, sc->sc_rx_chainmask, | |
| sc->sc_ht_extprotspacing, false, &status)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to reset hardware; hal status %u\n", status); | |
| error = -EIO; | |
| } | |
| spin_unlock_bh(&sc->sc_resetlock); | |
| if (ath_startrecv(sc) != 0) | |
| DPRINTF(sc, ATH_DBG_FATAL, "Unable to start recv logic\n"); | |
| /* | |
| * We may be doing a reset in response to a request | |
| * that changes the channel so update any state that | |
| * might change as a result. | |
| */ | |
| ath_setcurmode(sc, ath_chan2mode(sc->sc_ah->ah_curchan)); | |
| ath_update_txpow(sc); | |
| if (sc->sc_flags & SC_OP_BEACONS) | |
| ath_beacon_config(sc, ATH_IF_ID_ANY); /* restart beacons */ | |
| ath9k_hw_set_interrupts(ah, sc->sc_imask); | |
| if (retry_tx) { | |
| int i; | |
| for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) { | |
| if (ATH_TXQ_SETUP(sc, i)) { | |
| spin_lock_bh(&sc->tx.txq[i].axq_lock); | |
| ath_txq_schedule(sc, &sc->tx.txq[i]); | |
| spin_unlock_bh(&sc->tx.txq[i].axq_lock); | |
| } | |
| } | |
| } | |
| return error; | |
| } | |
| /* | |
| * This function will allocate both the DMA descriptor structure, and the | |
| * buffers it contains. These are used to contain the descriptors used | |
| * by the system. | |
| */ | |
| int ath_descdma_setup(struct ath_softc *sc, struct ath_descdma *dd, | |
| struct list_head *head, const char *name, | |
| int nbuf, int ndesc) | |
| { | |
| #define DS2PHYS(_dd, _ds) \ | |
| ((_dd)->dd_desc_paddr + ((caddr_t)(_ds) - (caddr_t)(_dd)->dd_desc)) | |
| #define ATH_DESC_4KB_BOUND_CHECK(_daddr) ((((_daddr) & 0xFFF) > 0xF7F) ? 1 : 0) | |
| #define ATH_DESC_4KB_BOUND_NUM_SKIPPED(_len) ((_len) / 4096) | |
| struct ath_desc *ds; | |
| struct ath_buf *bf; | |
| int i, bsize, error; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "%s DMA: %u buffers %u desc/buf\n", | |
| name, nbuf, ndesc); | |
| /* ath_desc must be a multiple of DWORDs */ | |
| if ((sizeof(struct ath_desc) % 4) != 0) { | |
| DPRINTF(sc, ATH_DBG_FATAL, "ath_desc not DWORD aligned\n"); | |
| ASSERT((sizeof(struct ath_desc) % 4) == 0); | |
| error = -ENOMEM; | |
| goto fail; | |
| } | |
| dd->dd_name = name; | |
| dd->dd_desc_len = sizeof(struct ath_desc) * nbuf * ndesc; | |
| /* | |
| * Need additional DMA memory because we can't use | |
| * descriptors that cross the 4K page boundary. Assume | |
| * one skipped descriptor per 4K page. | |
| */ | |
| if (!(sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_4KB_SPLITTRANS)) { | |
| u32 ndesc_skipped = | |
| ATH_DESC_4KB_BOUND_NUM_SKIPPED(dd->dd_desc_len); | |
| u32 dma_len; | |
| while (ndesc_skipped) { | |
| dma_len = ndesc_skipped * sizeof(struct ath_desc); | |
| dd->dd_desc_len += dma_len; | |
| ndesc_skipped = ATH_DESC_4KB_BOUND_NUM_SKIPPED(dma_len); | |
| }; | |
| } | |
| /* allocate descriptors */ | |
| dd->dd_desc = pci_alloc_consistent(sc->pdev, | |
| dd->dd_desc_len, | |
| &dd->dd_desc_paddr); | |
| if (dd->dd_desc == NULL) { | |
| error = -ENOMEM; | |
| goto fail; | |
| } | |
| ds = dd->dd_desc; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "%s DMA map: %p (%u) -> %llx (%u)\n", | |
| dd->dd_name, ds, (u32) dd->dd_desc_len, | |
| ito64(dd->dd_desc_paddr), /*XXX*/(u32) dd->dd_desc_len); | |
| /* allocate buffers */ | |
| bsize = sizeof(struct ath_buf) * nbuf; | |
| bf = kmalloc(bsize, GFP_KERNEL); | |
| if (bf == NULL) { | |
| error = -ENOMEM; | |
| goto fail2; | |
| } | |
| memset(bf, 0, bsize); | |
| dd->dd_bufptr = bf; | |
| INIT_LIST_HEAD(head); | |
| for (i = 0; i < nbuf; i++, bf++, ds += ndesc) { | |
| bf->bf_desc = ds; | |
| bf->bf_daddr = DS2PHYS(dd, ds); | |
| if (!(sc->sc_ah->ah_caps.hw_caps & | |
| ATH9K_HW_CAP_4KB_SPLITTRANS)) { | |
| /* | |
| * Skip descriptor addresses which can cause 4KB | |
| * boundary crossing (addr + length) with a 32 dword | |
| * descriptor fetch. | |
| */ | |
| while (ATH_DESC_4KB_BOUND_CHECK(bf->bf_daddr)) { | |
| ASSERT((caddr_t) bf->bf_desc < | |
| ((caddr_t) dd->dd_desc + | |
| dd->dd_desc_len)); | |
| ds += ndesc; | |
| bf->bf_desc = ds; | |
| bf->bf_daddr = DS2PHYS(dd, ds); | |
| } | |
| } | |
| list_add_tail(&bf->list, head); | |
| } | |
| return 0; | |
| fail2: | |
| pci_free_consistent(sc->pdev, | |
| dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr); | |
| fail: | |
| memset(dd, 0, sizeof(*dd)); | |
| return error; | |
| #undef ATH_DESC_4KB_BOUND_CHECK | |
| #undef ATH_DESC_4KB_BOUND_NUM_SKIPPED | |
| #undef DS2PHYS | |
| } | |
| void ath_descdma_cleanup(struct ath_softc *sc, | |
| struct ath_descdma *dd, | |
| struct list_head *head) | |
| { | |
| pci_free_consistent(sc->pdev, | |
| dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr); | |
| INIT_LIST_HEAD(head); | |
| kfree(dd->dd_bufptr); | |
| memset(dd, 0, sizeof(*dd)); | |
| } | |
| int ath_get_hal_qnum(u16 queue, struct ath_softc *sc) | |
| { | |
| int qnum; | |
| switch (queue) { | |
| case 0: | |
| qnum = sc->tx.hwq_map[ATH9K_WME_AC_VO]; | |
| break; | |
| case 1: | |
| qnum = sc->tx.hwq_map[ATH9K_WME_AC_VI]; | |
| break; | |
| case 2: | |
| qnum = sc->tx.hwq_map[ATH9K_WME_AC_BE]; | |
| break; | |
| case 3: | |
| qnum = sc->tx.hwq_map[ATH9K_WME_AC_BK]; | |
| break; | |
| default: | |
| qnum = sc->tx.hwq_map[ATH9K_WME_AC_BE]; | |
| break; | |
| } | |
| return qnum; | |
| } | |
| int ath_get_mac80211_qnum(u32 queue, struct ath_softc *sc) | |
| { | |
| int qnum; | |
| switch (queue) { | |
| case ATH9K_WME_AC_VO: | |
| qnum = 0; | |
| break; | |
| case ATH9K_WME_AC_VI: | |
| qnum = 1; | |
| break; | |
| case ATH9K_WME_AC_BE: | |
| qnum = 2; | |
| break; | |
| case ATH9K_WME_AC_BK: | |
| qnum = 3; | |
| break; | |
| default: | |
| qnum = -1; | |
| break; | |
| } | |
| return qnum; | |
| } | |
| /**********************/ | |
| /* mac80211 callbacks */ | |
| /**********************/ | |
| static int ath9k_start(struct ieee80211_hw *hw) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| struct ieee80211_channel *curchan = hw->conf.channel; | |
| struct ath9k_channel *init_channel; | |
| int error = 0, pos, status; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Starting driver with " | |
| "initial channel: %d MHz\n", curchan->center_freq); | |
| /* setup initial channel */ | |
| pos = ath_get_channel(sc, curchan); | |
| if (pos == -1) { | |
| DPRINTF(sc, ATH_DBG_FATAL, "Invalid channel: %d\n", curchan->center_freq); | |
| error = -EINVAL; | |
| goto error; | |
| } | |
| sc->tx_chan_width = ATH9K_HT_MACMODE_20; | |
| sc->sc_ah->ah_channels[pos].chanmode = | |
| (curchan->band == IEEE80211_BAND_2GHZ) ? CHANNEL_G : CHANNEL_A; | |
| init_channel = &sc->sc_ah->ah_channels[pos]; | |
| /* Reset SERDES registers */ | |
| ath9k_hw_configpcipowersave(sc->sc_ah, 0); | |
| /* | |
| * The basic interface to setting the hardware in a good | |
| * state is ``reset''. On return the hardware is known to | |
| * be powered up and with interrupts disabled. This must | |
| * be followed by initialization of the appropriate bits | |
| * and then setup of the interrupt mask. | |
| */ | |
| spin_lock_bh(&sc->sc_resetlock); | |
| if (!ath9k_hw_reset(sc->sc_ah, init_channel, | |
| sc->tx_chan_width, | |
| sc->sc_tx_chainmask, sc->sc_rx_chainmask, | |
| sc->sc_ht_extprotspacing, false, &status)) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to reset hardware; hal status %u " | |
| "(freq %u flags 0x%x)\n", status, | |
| init_channel->channel, init_channel->channelFlags); | |
| error = -EIO; | |
| spin_unlock_bh(&sc->sc_resetlock); | |
| goto error; | |
| } | |
| spin_unlock_bh(&sc->sc_resetlock); | |
| /* | |
| * This is needed only to setup initial state | |
| * but it's best done after a reset. | |
| */ | |
| ath_update_txpow(sc); | |
| /* | |
| * Setup the hardware after reset: | |
| * The receive engine is set going. | |
| * Frame transmit is handled entirely | |
| * in the frame output path; there's nothing to do | |
| * here except setup the interrupt mask. | |
| */ | |
| if (ath_startrecv(sc) != 0) { | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to start recv logic\n"); | |
| error = -EIO; | |
| goto error; | |
| } | |
| /* Setup our intr mask. */ | |
| sc->sc_imask = ATH9K_INT_RX | ATH9K_INT_TX | |
| | ATH9K_INT_RXEOL | ATH9K_INT_RXORN | |
| | ATH9K_INT_FATAL | ATH9K_INT_GLOBAL; | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_GTT) | |
| sc->sc_imask |= ATH9K_INT_GTT; | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT) | |
| sc->sc_imask |= ATH9K_INT_CST; | |
| /* | |
| * Enable MIB interrupts when there are hardware phy counters. | |
| * Note we only do this (at the moment) for station mode. | |
| */ | |
| if (ath9k_hw_phycounters(sc->sc_ah) && | |
| ((sc->sc_ah->ah_opmode == NL80211_IFTYPE_STATION) || | |
| (sc->sc_ah->ah_opmode == NL80211_IFTYPE_ADHOC))) | |
| sc->sc_imask |= ATH9K_INT_MIB; | |
| /* | |
| * Some hardware processes the TIM IE and fires an | |
| * interrupt when the TIM bit is set. For hardware | |
| * that does, if not overridden by configuration, | |
| * enable the TIM interrupt when operating as station. | |
| */ | |
| if ((sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_ENHANCEDPM) && | |
| (sc->sc_ah->ah_opmode == NL80211_IFTYPE_STATION) && | |
| !sc->sc_config.swBeaconProcess) | |
| sc->sc_imask |= ATH9K_INT_TIM; | |
| ath_setcurmode(sc, ath_chan2mode(init_channel)); | |
| sc->sc_flags &= ~SC_OP_INVALID; | |
| /* Disable BMISS interrupt when we're not associated */ | |
| sc->sc_imask &= ~(ATH9K_INT_SWBA | ATH9K_INT_BMISS); | |
| ath9k_hw_set_interrupts(sc->sc_ah, sc->sc_imask); | |
| ieee80211_wake_queues(sc->hw); | |
| #if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE) | |
| error = ath_start_rfkill_poll(sc); | |
| #endif | |
| error: | |
| return error; | |
| } | |
| static int ath9k_tx(struct ieee80211_hw *hw, | |
| struct sk_buff *skb) | |
| { | |
| struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); | |
| struct ath_softc *sc = hw->priv; | |
| struct ath_tx_control txctl; | |
| int hdrlen, padsize; | |
| memset(&txctl, 0, sizeof(struct ath_tx_control)); | |
| /* | |
| * As a temporary workaround, assign seq# here; this will likely need | |
| * to be cleaned up to work better with Beacon transmission and virtual | |
| * BSSes. | |
| */ | |
| if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) { | |
| struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data; | |
| if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT) | |
| sc->tx.seq_no += 0x10; | |
| hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG); | |
| hdr->seq_ctrl |= cpu_to_le16(sc->tx.seq_no); | |
| } | |
| /* Add the padding after the header if this is not already done */ | |
| hdrlen = ieee80211_get_hdrlen_from_skb(skb); | |
| if (hdrlen & 3) { | |
| padsize = hdrlen % 4; | |
| if (skb_headroom(skb) < padsize) | |
| return -1; | |
| skb_push(skb, padsize); | |
| memmove(skb->data, skb->data + padsize, hdrlen); | |
| } | |
| /* Check if a tx queue is available */ | |
| txctl.txq = ath_test_get_txq(sc, skb); | |
| if (!txctl.txq) | |
| goto exit; | |
| DPRINTF(sc, ATH_DBG_XMIT, "transmitting packet, skb: %p\n", skb); | |
| if (ath_tx_start(sc, skb, &txctl) != 0) { | |
| DPRINTF(sc, ATH_DBG_XMIT, "TX failed\n"); | |
| goto exit; | |
| } | |
| return 0; | |
| exit: | |
| dev_kfree_skb_any(skb); | |
| return 0; | |
| } | |
| static void ath9k_stop(struct ieee80211_hw *hw) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| if (sc->sc_flags & SC_OP_INVALID) { | |
| DPRINTF(sc, ATH_DBG_ANY, "Device not present\n"); | |
| return; | |
| } | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Cleaning up\n"); | |
| ieee80211_stop_queues(sc->hw); | |
| /* make sure h/w will not generate any interrupt | |
| * before setting the invalid flag. */ | |
| ath9k_hw_set_interrupts(sc->sc_ah, 0); | |
| if (!(sc->sc_flags & SC_OP_INVALID)) { | |
| ath_draintxq(sc, false); | |
| ath_stoprecv(sc); | |
| ath9k_hw_phy_disable(sc->sc_ah); | |
| } else | |
| sc->rx.rxlink = NULL; | |
| #if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE) | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT) | |
| cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll); | |
| #endif | |
| /* disable HAL and put h/w to sleep */ | |
| ath9k_hw_disable(sc->sc_ah); | |
| ath9k_hw_configpcipowersave(sc->sc_ah, 1); | |
| sc->sc_flags |= SC_OP_INVALID; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Driver halt\n"); | |
| } | |
| static int ath9k_add_interface(struct ieee80211_hw *hw, | |
| struct ieee80211_if_init_conf *conf) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| struct ath_vap *avp = (void *)conf->vif->drv_priv; | |
| enum nl80211_iftype ic_opmode = NL80211_IFTYPE_UNSPECIFIED; | |
| /* Support only vap for now */ | |
| if (sc->sc_nvaps) | |
| return -ENOBUFS; | |
| switch (conf->type) { | |
| case NL80211_IFTYPE_STATION: | |
| ic_opmode = NL80211_IFTYPE_STATION; | |
| break; | |
| case NL80211_IFTYPE_ADHOC: | |
| ic_opmode = NL80211_IFTYPE_ADHOC; | |
| break; | |
| case NL80211_IFTYPE_AP: | |
| ic_opmode = NL80211_IFTYPE_AP; | |
| break; | |
| default: | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Interface type %d not yet supported\n", conf->type); | |
| return -EOPNOTSUPP; | |
| } | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Attach a VAP of type: %d\n", ic_opmode); | |
| /* Set the VAP opmode */ | |
| avp->av_opmode = ic_opmode; | |
| avp->av_bslot = -1; | |
| if (ic_opmode == NL80211_IFTYPE_AP) | |
| ath9k_hw_set_tsfadjust(sc->sc_ah, 1); | |
| sc->sc_vaps[0] = conf->vif; | |
| sc->sc_nvaps++; | |
| /* Set the device opmode */ | |
| sc->sc_ah->ah_opmode = ic_opmode; | |
| if (conf->type == NL80211_IFTYPE_AP) { | |
| /* TODO: is this a suitable place to start ANI for AP mode? */ | |
| /* Start ANI */ | |
| mod_timer(&sc->sc_ani.timer, | |
| jiffies + msecs_to_jiffies(ATH_ANI_POLLINTERVAL)); | |
| } | |
| return 0; | |
| } | |
| static void ath9k_remove_interface(struct ieee80211_hw *hw, | |
| struct ieee80211_if_init_conf *conf) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| struct ath_vap *avp = (void *)conf->vif->drv_priv; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Detach Interface\n"); | |
| /* Stop ANI */ | |
| del_timer_sync(&sc->sc_ani.timer); | |
| /* Reclaim beacon resources */ | |
| if (sc->sc_ah->ah_opmode == NL80211_IFTYPE_AP || | |
| sc->sc_ah->ah_opmode == NL80211_IFTYPE_ADHOC) { | |
| ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq); | |
| ath_beacon_return(sc, avp); | |
| } | |
| sc->sc_flags &= ~SC_OP_BEACONS; | |
| sc->sc_vaps[0] = NULL; | |
| sc->sc_nvaps--; | |
| } | |
| static int ath9k_config(struct ieee80211_hw *hw, u32 changed) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| struct ieee80211_conf *conf = &hw->conf; | |
| mutex_lock(&sc->mutex); | |
| if (changed & (IEEE80211_CONF_CHANGE_CHANNEL | | |
| IEEE80211_CONF_CHANGE_HT)) { | |
| struct ieee80211_channel *curchan = hw->conf.channel; | |
| int pos; | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Set channel: %d MHz\n", | |
| curchan->center_freq); | |
| pos = ath_get_channel(sc, curchan); | |
| if (pos == -1) { | |
| DPRINTF(sc, ATH_DBG_FATAL, "Invalid channel: %d\n", | |
| curchan->center_freq); | |
| mutex_unlock(&sc->mutex); | |
| return -EINVAL; | |
| } | |
| sc->tx_chan_width = ATH9K_HT_MACMODE_20; | |
| sc->sc_ah->ah_channels[pos].chanmode = | |
| (curchan->band == IEEE80211_BAND_2GHZ) ? | |
| CHANNEL_G : CHANNEL_A; | |
| if (conf->ht.enabled) { | |
| if (conf->ht.channel_type == NL80211_CHAN_HT40PLUS || | |
| conf->ht.channel_type == NL80211_CHAN_HT40MINUS) | |
| sc->tx_chan_width = ATH9K_HT_MACMODE_2040; | |
| sc->sc_ah->ah_channels[pos].chanmode = | |
| ath_get_extchanmode(sc, curchan, | |
| conf->ht.channel_type); | |
| } | |
| ath_update_chainmask(sc, conf->ht.enabled); | |
| if (ath_set_channel(sc, &sc->sc_ah->ah_channels[pos]) < 0) { | |
| DPRINTF(sc, ATH_DBG_FATAL, "Unable to set channel\n"); | |
| mutex_unlock(&sc->mutex); | |
| return -EINVAL; | |
| } | |
| } | |
| if (changed & IEEE80211_CONF_CHANGE_POWER) | |
| sc->sc_config.txpowlimit = 2 * conf->power_level; | |
| mutex_unlock(&sc->mutex); | |
| return 0; | |
| } | |
| static int ath9k_config_interface(struct ieee80211_hw *hw, | |
| struct ieee80211_vif *vif, | |
| struct ieee80211_if_conf *conf) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| struct ath_hal *ah = sc->sc_ah; | |
| struct ath_vap *avp = (void *)vif->drv_priv; | |
| u32 rfilt = 0; | |
| int error, i; | |
| /* TODO: Need to decide which hw opmode to use for multi-interface | |
| * cases */ | |
| if (vif->type == NL80211_IFTYPE_AP && | |
| ah->ah_opmode != NL80211_IFTYPE_AP) { | |
| ah->ah_opmode = NL80211_IFTYPE_STATION; | |
| ath9k_hw_setopmode(ah); | |
| ath9k_hw_write_associd(ah, sc->sc_myaddr, 0); | |
| /* Request full reset to get hw opmode changed properly */ | |
| sc->sc_flags |= SC_OP_FULL_RESET; | |
| } | |
| if ((conf->changed & IEEE80211_IFCC_BSSID) && | |
| !is_zero_ether_addr(conf->bssid)) { | |
| switch (vif->type) { | |
| case NL80211_IFTYPE_STATION: | |
| case NL80211_IFTYPE_ADHOC: | |
| /* Set BSSID */ | |
| memcpy(sc->sc_curbssid, conf->bssid, ETH_ALEN); | |
| sc->sc_curaid = 0; | |
| ath9k_hw_write_associd(sc->sc_ah, sc->sc_curbssid, | |
| sc->sc_curaid); | |
| /* Set aggregation protection mode parameters */ | |
| sc->sc_config.ath_aggr_prot = 0; | |
| DPRINTF(sc, ATH_DBG_CONFIG, | |
| "RX filter 0x%x bssid %pM aid 0x%x\n", | |
| rfilt, sc->sc_curbssid, sc->sc_curaid); | |
| /* need to reconfigure the beacon */ | |
| sc->sc_flags &= ~SC_OP_BEACONS ; | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| if ((conf->changed & IEEE80211_IFCC_BEACON) && | |
| ((vif->type == NL80211_IFTYPE_ADHOC) || | |
| (vif->type == NL80211_IFTYPE_AP))) { | |
| /* | |
| * Allocate and setup the beacon frame. | |
| * | |
| * Stop any previous beacon DMA. This may be | |
| * necessary, for example, when an ibss merge | |
| * causes reconfiguration; we may be called | |
| * with beacon transmission active. | |
| */ | |
| ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq); | |
| error = ath_beacon_alloc(sc, 0); | |
| if (error != 0) | |
| return error; | |
| ath_beacon_sync(sc, 0); | |
| } | |
| /* Check for WLAN_CAPABILITY_PRIVACY ? */ | |
| if ((avp->av_opmode != NL80211_IFTYPE_STATION)) { | |
| for (i = 0; i < IEEE80211_WEP_NKID; i++) | |
| if (ath9k_hw_keyisvalid(sc->sc_ah, (u16)i)) | |
| ath9k_hw_keysetmac(sc->sc_ah, | |
| (u16)i, | |
| sc->sc_curbssid); | |
| } | |
| /* Only legacy IBSS for now */ | |
| if (vif->type == NL80211_IFTYPE_ADHOC) | |
| ath_update_chainmask(sc, 0); | |
| return 0; | |
| } | |
| #define SUPPORTED_FILTERS \ | |
| (FIF_PROMISC_IN_BSS | \ | |
| FIF_ALLMULTI | \ | |
| FIF_CONTROL | \ | |
| FIF_OTHER_BSS | \ | |
| FIF_BCN_PRBRESP_PROMISC | \ | |
| FIF_FCSFAIL) | |
| /* FIXME: sc->sc_full_reset ? */ | |
| static void ath9k_configure_filter(struct ieee80211_hw *hw, | |
| unsigned int changed_flags, | |
| unsigned int *total_flags, | |
| int mc_count, | |
| struct dev_mc_list *mclist) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| u32 rfilt; | |
| changed_flags &= SUPPORTED_FILTERS; | |
| *total_flags &= SUPPORTED_FILTERS; | |
| sc->rx.rxfilter = *total_flags; | |
| rfilt = ath_calcrxfilter(sc); | |
| ath9k_hw_setrxfilter(sc->sc_ah, rfilt); | |
| if (changed_flags & FIF_BCN_PRBRESP_PROMISC) { | |
| if (*total_flags & FIF_BCN_PRBRESP_PROMISC) | |
| ath9k_hw_write_associd(sc->sc_ah, ath_bcast_mac, 0); | |
| } | |
| DPRINTF(sc, ATH_DBG_CONFIG, "Set HW RX filter: 0x%x\n", sc->rx.rxfilter); | |
| } | |
| static void ath9k_sta_notify(struct ieee80211_hw *hw, | |
| struct ieee80211_vif *vif, | |
| enum sta_notify_cmd cmd, | |
| struct ieee80211_sta *sta) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| switch (cmd) { | |
| case STA_NOTIFY_ADD: | |
| ath_node_attach(sc, sta); | |
| break; | |
| case STA_NOTIFY_REMOVE: | |
| ath_node_detach(sc, sta); | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| static int ath9k_conf_tx(struct ieee80211_hw *hw, | |
| u16 queue, | |
| const struct ieee80211_tx_queue_params *params) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| struct ath9k_tx_queue_info qi; | |
| int ret = 0, qnum; | |
| if (queue >= WME_NUM_AC) | |
| return 0; | |
| qi.tqi_aifs = params->aifs; | |
| qi.tqi_cwmin = params->cw_min; | |
| qi.tqi_cwmax = params->cw_max; | |
| qi.tqi_burstTime = params->txop; | |
| qnum = ath_get_hal_qnum(queue, sc); | |
| DPRINTF(sc, ATH_DBG_CONFIG, | |
| "Configure tx [queue/halq] [%d/%d], " | |
| "aifs: %d, cw_min: %d, cw_max: %d, txop: %d\n", | |
| queue, qnum, params->aifs, params->cw_min, | |
| params->cw_max, params->txop); | |
| ret = ath_txq_update(sc, qnum, &qi); | |
| if (ret) | |
| DPRINTF(sc, ATH_DBG_FATAL, "TXQ Update failed\n"); | |
| return ret; | |
| } | |
| static int ath9k_set_key(struct ieee80211_hw *hw, | |
| enum set_key_cmd cmd, | |
| const u8 *local_addr, | |
| const u8 *addr, | |
| struct ieee80211_key_conf *key) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| int ret = 0; | |
| DPRINTF(sc, ATH_DBG_KEYCACHE, "Set HW Key\n"); | |
| switch (cmd) { | |
| case SET_KEY: | |
| ret = ath_key_config(sc, addr, key); | |
| if (ret >= 0) { | |
| key->hw_key_idx = ret; | |
| /* push IV and Michael MIC generation to stack */ | |
| key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; | |
| if (key->alg == ALG_TKIP) | |
| key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; | |
| ret = 0; | |
| } | |
| break; | |
| case DISABLE_KEY: | |
| ath_key_delete(sc, key); | |
| break; | |
| default: | |
| ret = -EINVAL; | |
| } | |
| return ret; | |
| } | |
| static void ath9k_bss_info_changed(struct ieee80211_hw *hw, | |
| struct ieee80211_vif *vif, | |
| struct ieee80211_bss_conf *bss_conf, | |
| u32 changed) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| if (changed & BSS_CHANGED_ERP_PREAMBLE) { | |
| DPRINTF(sc, ATH_DBG_CONFIG, "BSS Changed PREAMBLE %d\n", | |
| bss_conf->use_short_preamble); | |
| if (bss_conf->use_short_preamble) | |
| sc->sc_flags |= SC_OP_PREAMBLE_SHORT; | |
| else | |
| sc->sc_flags &= ~SC_OP_PREAMBLE_SHORT; | |
| } | |
| if (changed & BSS_CHANGED_ERP_CTS_PROT) { | |
| DPRINTF(sc, ATH_DBG_CONFIG, "BSS Changed CTS PROT %d\n", | |
| bss_conf->use_cts_prot); | |
| if (bss_conf->use_cts_prot && | |
| hw->conf.channel->band != IEEE80211_BAND_5GHZ) | |
| sc->sc_flags |= SC_OP_PROTECT_ENABLE; | |
| else | |
| sc->sc_flags &= ~SC_OP_PROTECT_ENABLE; | |
| } | |
| if (changed & BSS_CHANGED_ASSOC) { | |
| DPRINTF(sc, ATH_DBG_CONFIG, "BSS Changed ASSOC %d\n", | |
| bss_conf->assoc); | |
| ath9k_bss_assoc_info(sc, vif, bss_conf); | |
| } | |
| } | |
| static u64 ath9k_get_tsf(struct ieee80211_hw *hw) | |
| { | |
| u64 tsf; | |
| struct ath_softc *sc = hw->priv; | |
| struct ath_hal *ah = sc->sc_ah; | |
| tsf = ath9k_hw_gettsf64(ah); | |
| return tsf; | |
| } | |
| static void ath9k_reset_tsf(struct ieee80211_hw *hw) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| struct ath_hal *ah = sc->sc_ah; | |
| ath9k_hw_reset_tsf(ah); | |
| } | |
| static int ath9k_ampdu_action(struct ieee80211_hw *hw, | |
| enum ieee80211_ampdu_mlme_action action, | |
| struct ieee80211_sta *sta, | |
| u16 tid, u16 *ssn) | |
| { | |
| struct ath_softc *sc = hw->priv; | |
| int ret = 0; | |
| switch (action) { | |
| case IEEE80211_AMPDU_RX_START: | |
| if (!(sc->sc_flags & SC_OP_RXAGGR)) | |
| ret = -ENOTSUPP; | |
| break; | |
| case IEEE80211_AMPDU_RX_STOP: | |
| break; | |
| case IEEE80211_AMPDU_TX_START: | |
| ret = ath_tx_aggr_start(sc, sta, tid, ssn); | |
| if (ret < 0) | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to start TX aggregation\n"); | |
| else | |
| ieee80211_start_tx_ba_cb_irqsafe(hw, sta->addr, tid); | |
| break; | |
| case IEEE80211_AMPDU_TX_STOP: | |
| ret = ath_tx_aggr_stop(sc, sta, tid); | |
| if (ret < 0) | |
| DPRINTF(sc, ATH_DBG_FATAL, | |
| "Unable to stop TX aggregation\n"); | |
| ieee80211_stop_tx_ba_cb_irqsafe(hw, sta->addr, tid); | |
| break; | |
| case IEEE80211_AMPDU_TX_RESUME: | |
| ath_tx_aggr_resume(sc, sta, tid); | |
| break; | |
| default: | |
| DPRINTF(sc, ATH_DBG_FATAL, "Unknown AMPDU action\n"); | |
| } | |
| return ret; | |
| } | |
| static struct ieee80211_ops ath9k_ops = { | |
| .tx = ath9k_tx, | |
| .start = ath9k_start, | |
| .stop = ath9k_stop, | |
| .add_interface = ath9k_add_interface, | |
| .remove_interface = ath9k_remove_interface, | |
| .config = ath9k_config, | |
| .config_interface = ath9k_config_interface, | |
| .configure_filter = ath9k_configure_filter, | |
| .sta_notify = ath9k_sta_notify, | |
| .conf_tx = ath9k_conf_tx, | |
| .bss_info_changed = ath9k_bss_info_changed, | |
| .set_key = ath9k_set_key, | |
| .get_tsf = ath9k_get_tsf, | |
| .reset_tsf = ath9k_reset_tsf, | |
| .ampdu_action = ath9k_ampdu_action, | |
| }; | |
| static struct { | |
| u32 version; | |
| const char * name; | |
| } ath_mac_bb_names[] = { | |
| { AR_SREV_VERSION_5416_PCI, "5416" }, | |
| { AR_SREV_VERSION_5416_PCIE, "5418" }, | |
| { AR_SREV_VERSION_9100, "9100" }, | |
| { AR_SREV_VERSION_9160, "9160" }, | |
| { AR_SREV_VERSION_9280, "9280" }, | |
| { AR_SREV_VERSION_9285, "9285" } | |
| }; | |
| static struct { | |
| u16 version; | |
| const char * name; | |
| } ath_rf_names[] = { | |
| { 0, "5133" }, | |
| { AR_RAD5133_SREV_MAJOR, "5133" }, | |
| { AR_RAD5122_SREV_MAJOR, "5122" }, | |
| { AR_RAD2133_SREV_MAJOR, "2133" }, | |
| { AR_RAD2122_SREV_MAJOR, "2122" } | |
| }; | |
| /* | |
| * Return the MAC/BB name. "????" is returned if the MAC/BB is unknown. | |
| */ | |
| static const char * | |
| ath_mac_bb_name(u32 mac_bb_version) | |
| { | |
| int i; | |
| for (i=0; i<ARRAY_SIZE(ath_mac_bb_names); i++) { | |
| if (ath_mac_bb_names[i].version == mac_bb_version) { | |
| return ath_mac_bb_names[i].name; | |
| } | |
| } | |
| return "????"; | |
| } | |
| /* | |
| * Return the RF name. "????" is returned if the RF is unknown. | |
| */ | |
| static const char * | |
| ath_rf_name(u16 rf_version) | |
| { | |
| int i; | |
| for (i=0; i<ARRAY_SIZE(ath_rf_names); i++) { | |
| if (ath_rf_names[i].version == rf_version) { | |
| return ath_rf_names[i].name; | |
| } | |
| } | |
| return "????"; | |
| } | |
| static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) | |
| { | |
| void __iomem *mem; | |
| struct ath_softc *sc; | |
| struct ieee80211_hw *hw; | |
| u8 csz; | |
| u32 val; | |
| int ret = 0; | |
| struct ath_hal *ah; | |
| if (pci_enable_device(pdev)) | |
| return -EIO; | |
| ret = pci_set_dma_mask(pdev, DMA_32BIT_MASK); | |
| if (ret) { | |
| printk(KERN_ERR "ath9k: 32-bit DMA not available\n"); | |
| goto bad; | |
| } | |
| ret = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); | |
| if (ret) { | |
| printk(KERN_ERR "ath9k: 32-bit DMA consistent " | |
| "DMA enable failed\n"); | |
| goto bad; | |
| } | |
| /* | |
| * Cache line size is used to size and align various | |
| * structures used to communicate with the hardware. | |
| */ | |
| pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &csz); | |
| if (csz == 0) { | |
| /* | |
| * Linux 2.4.18 (at least) writes the cache line size | |
| * register as a 16-bit wide register which is wrong. | |
| * We must have this setup properly for rx buffer | |
| * DMA to work so force a reasonable value here if it | |
| * comes up zero. | |
| */ | |
| csz = L1_CACHE_BYTES / sizeof(u32); | |
| pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, csz); | |
| } | |
| /* | |
| * The default setting of latency timer yields poor results, | |
| * set it to the value used by other systems. It may be worth | |
| * tweaking this setting more. | |
| */ | |
| pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xa8); | |
| pci_set_master(pdev); | |
| /* | |
| * Disable the RETRY_TIMEOUT register (0x41) to keep | |
| * PCI Tx retries from interfering with C3 CPU state. | |
| */ | |
| pci_read_config_dword(pdev, 0x40, &val); | |
| if ((val & 0x0000ff00) != 0) | |
| pci_write_config_dword(pdev, 0x40, val & 0xffff00ff); | |
| ret = pci_request_region(pdev, 0, "ath9k"); | |
| if (ret) { | |
| dev_err(&pdev->dev, "PCI memory region reserve error\n"); | |
| ret = -ENODEV; | |
| goto bad; | |
| } | |
| mem = pci_iomap(pdev, 0, 0); | |
| if (!mem) { | |
| printk(KERN_ERR "PCI memory map error\n") ; | |
| ret = -EIO; | |
| goto bad1; | |
| } | |
| hw = ieee80211_alloc_hw(sizeof(struct ath_softc), &ath9k_ops); | |
| if (hw == NULL) { | |
| printk(KERN_ERR "ath_pci: no memory for ieee80211_hw\n"); | |
| goto bad2; | |
| } | |
| SET_IEEE80211_DEV(hw, &pdev->dev); | |
| pci_set_drvdata(pdev, hw); | |
| sc = hw->priv; | |
| sc->hw = hw; | |
| sc->pdev = pdev; | |
| sc->mem = mem; | |
| if (ath_attach(id->device, sc) != 0) { | |
| ret = -ENODEV; | |
| goto bad3; | |
| } | |
| /* setup interrupt service routine */ | |
| if (request_irq(pdev->irq, ath_isr, IRQF_SHARED, "ath", sc)) { | |
| printk(KERN_ERR "%s: request_irq failed\n", | |
| wiphy_name(hw->wiphy)); | |
| ret = -EIO; | |
| goto bad4; | |
| } | |
| ah = sc->sc_ah; | |
| printk(KERN_INFO | |
| "%s: Atheros AR%s MAC/BB Rev:%x " | |
| "AR%s RF Rev:%x: mem=0x%lx, irq=%d\n", | |
| wiphy_name(hw->wiphy), | |
| ath_mac_bb_name(ah->ah_macVersion), | |
| ah->ah_macRev, | |
| ath_rf_name((ah->ah_analog5GhzRev & AR_RADIO_SREV_MAJOR)), | |
| ah->ah_phyRev, | |
| (unsigned long)mem, pdev->irq); | |
| return 0; | |
| bad4: | |
| ath_detach(sc); | |
| bad3: | |
| ieee80211_free_hw(hw); | |
| bad2: | |
| pci_iounmap(pdev, mem); | |
| bad1: | |
| pci_release_region(pdev, 0); | |
| bad: | |
| pci_disable_device(pdev); | |
| return ret; | |
| } | |
| static void ath_pci_remove(struct pci_dev *pdev) | |
| { | |
| struct ieee80211_hw *hw = pci_get_drvdata(pdev); | |
| struct ath_softc *sc = hw->priv; | |
| ath_detach(sc); | |
| if (pdev->irq) | |
| free_irq(pdev->irq, sc); | |
| pci_iounmap(pdev, sc->mem); | |
| pci_release_region(pdev, 0); | |
| pci_disable_device(pdev); | |
| ieee80211_free_hw(hw); | |
| } | |
| #ifdef CONFIG_PM | |
| static int ath_pci_suspend(struct pci_dev *pdev, pm_message_t state) | |
| { | |
| struct ieee80211_hw *hw = pci_get_drvdata(pdev); | |
| struct ath_softc *sc = hw->priv; | |
| ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1); | |
| #if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE) | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT) | |
| cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll); | |
| #endif | |
| pci_save_state(pdev); | |
| pci_disable_device(pdev); | |
| pci_set_power_state(pdev, 3); | |
| return 0; | |
| } | |
| static int ath_pci_resume(struct pci_dev *pdev) | |
| { | |
| struct ieee80211_hw *hw = pci_get_drvdata(pdev); | |
| struct ath_softc *sc = hw->priv; | |
| u32 val; | |
| int err; | |
| err = pci_enable_device(pdev); | |
| if (err) | |
| return err; | |
| pci_restore_state(pdev); | |
| /* | |
| * Suspend/Resume resets the PCI configuration space, so we have to | |
| * re-disable the RETRY_TIMEOUT register (0x41) to keep | |
| * PCI Tx retries from interfering with C3 CPU state | |
| */ | |
| pci_read_config_dword(pdev, 0x40, &val); | |
| if ((val & 0x0000ff00) != 0) | |
| pci_write_config_dword(pdev, 0x40, val & 0xffff00ff); | |
| /* Enable LED */ | |
| ath9k_hw_cfg_output(sc->sc_ah, ATH_LED_PIN, | |
| AR_GPIO_OUTPUT_MUX_AS_OUTPUT); | |
| ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1); | |
| #if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE) | |
| /* | |
| * check the h/w rfkill state on resume | |
| * and start the rfkill poll timer | |
| */ | |
| if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT) | |
| queue_delayed_work(sc->hw->workqueue, | |
| &sc->rf_kill.rfkill_poll, 0); | |
| #endif | |
| return 0; | |
| } | |
| #endif /* CONFIG_PM */ | |
| MODULE_DEVICE_TABLE(pci, ath_pci_id_table); | |
| static struct pci_driver ath_pci_driver = { | |
| .name = "ath9k", | |
| .id_table = ath_pci_id_table, | |
| .probe = ath_pci_probe, | |
| .remove = ath_pci_remove, | |
| #ifdef CONFIG_PM | |
| .suspend = ath_pci_suspend, | |
| .resume = ath_pci_resume, | |
| #endif /* CONFIG_PM */ | |
| }; | |
| static int __init init_ath_pci(void) | |
| { | |
| int error; | |
| printk(KERN_INFO "%s: %s\n", dev_info, ATH_PCI_VERSION); | |
| /* Register rate control algorithm */ | |
| error = ath_rate_control_register(); | |
| if (error != 0) { | |
| printk(KERN_ERR | |
| "Unable to register rate control algorithm: %d\n", | |
| error); | |
| ath_rate_control_unregister(); | |
| return error; | |
| } | |
| if (pci_register_driver(&ath_pci_driver) < 0) { | |
| printk(KERN_ERR | |
| "ath_pci: No devices found, driver not installed.\n"); | |
| ath_rate_control_unregister(); | |
| pci_unregister_driver(&ath_pci_driver); | |
| return -ENODEV; | |
| } | |
| return 0; | |
| } | |
| module_init(init_ath_pci); | |
| static void __exit exit_ath_pci(void) | |
| { | |
| ath_rate_control_unregister(); | |
| pci_unregister_driver(&ath_pci_driver); | |
| printk(KERN_INFO "%s: Driver unloaded\n", dev_info); | |
| } | |
| module_exit(exit_ath_pci); |