| /*- | |
| * Copyright (c) 2002-2005 Sam Leffler, Errno Consulting | |
| * Copyright (c) 2004-2005 Atheros Communications, Inc. | |
| * Copyright (c) 2006 Devicescape Software, Inc. | |
| * Copyright (c) 2007 Jiri Slaby <jirislaby@gmail.com> | |
| * Copyright (c) 2007 Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> | |
| * | |
| * All rights reserved. | |
| * | |
| * Redistribution and use in source and binary forms, with or without | |
| * modification, are permitted provided that the following conditions | |
| * are met: | |
| * 1. Redistributions of source code must retain the above copyright | |
| * notice, this list of conditions and the following disclaimer, | |
| * without modification. | |
| * 2. Redistributions in binary form must reproduce at minimum a disclaimer | |
| * similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any | |
| * redistribution must be conditioned upon including a substantially | |
| * similar Disclaimer requirement for further binary redistribution. | |
| * 3. Neither the names of the above-listed copyright holders nor the names | |
| * of any contributors may be used to endorse or promote products derived | |
| * from this software without specific prior written permission. | |
| * | |
| * Alternatively, this software may be distributed under the terms of the | |
| * GNU General Public License ("GPL") version 2 as published by the Free | |
| * Software Foundation. | |
| * | |
| * NO WARRANTY | |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS | |
| * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT | |
| * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY | |
| * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL | |
| * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, | |
| * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF | |
| * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS | |
| * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER | |
| * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) | |
| * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF | |
| * THE POSSIBILITY OF SUCH DAMAGES. | |
| * | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/delay.h> | |
| #include <linux/hardirq.h> | |
| #include <linux/if.h> | |
| #include <linux/io.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/cache.h> | |
| #include <linux/pci.h> | |
| #include <linux/ethtool.h> | |
| #include <linux/uaccess.h> | |
| #include <net/ieee80211_radiotap.h> | |
| #include <asm/unaligned.h> | |
| #include "base.h" | |
| #include "reg.h" | |
| #include "debug.h" | |
| static int ath5k_calinterval = 10; /* Calibrate PHY every 10 secs (TODO: Fixme) */ | |
| static int modparam_nohwcrypt; | |
| module_param_named(nohwcrypt, modparam_nohwcrypt, int, 0444); | |
| MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); | |
| /******************\ | |
| * Internal defines * | |
| \******************/ | |
| /* Module info */ | |
| MODULE_AUTHOR("Jiri Slaby"); | |
| MODULE_AUTHOR("Nick Kossifidis"); | |
| MODULE_DESCRIPTION("Support for 5xxx series of Atheros 802.11 wireless LAN cards."); | |
| MODULE_SUPPORTED_DEVICE("Atheros 5xxx WLAN cards"); | |
| MODULE_LICENSE("Dual BSD/GPL"); | |
| MODULE_VERSION("0.6.0 (EXPERIMENTAL)"); | |
| /* Known PCI ids */ | |
| static struct pci_device_id ath5k_pci_id_table[] __devinitdata = { | |
| { PCI_VDEVICE(ATHEROS, 0x0207), .driver_data = AR5K_AR5210 }, /* 5210 early */ | |
| { PCI_VDEVICE(ATHEROS, 0x0007), .driver_data = AR5K_AR5210 }, /* 5210 */ | |
| { PCI_VDEVICE(ATHEROS, 0x0011), .driver_data = AR5K_AR5211 }, /* 5311 - this is on AHB bus !*/ | |
| { PCI_VDEVICE(ATHEROS, 0x0012), .driver_data = AR5K_AR5211 }, /* 5211 */ | |
| { PCI_VDEVICE(ATHEROS, 0x0013), .driver_data = AR5K_AR5212 }, /* 5212 */ | |
| { PCI_VDEVICE(3COM_2, 0x0013), .driver_data = AR5K_AR5212 }, /* 3com 5212 */ | |
| { PCI_VDEVICE(3COM, 0x0013), .driver_data = AR5K_AR5212 }, /* 3com 3CRDAG675 5212 */ | |
| { PCI_VDEVICE(ATHEROS, 0x1014), .driver_data = AR5K_AR5212 }, /* IBM minipci 5212 */ | |
| { PCI_VDEVICE(ATHEROS, 0x0014), .driver_data = AR5K_AR5212 }, /* 5212 combatible */ | |
| { PCI_VDEVICE(ATHEROS, 0x0015), .driver_data = AR5K_AR5212 }, /* 5212 combatible */ | |
| { PCI_VDEVICE(ATHEROS, 0x0016), .driver_data = AR5K_AR5212 }, /* 5212 combatible */ | |
| { PCI_VDEVICE(ATHEROS, 0x0017), .driver_data = AR5K_AR5212 }, /* 5212 combatible */ | |
| { PCI_VDEVICE(ATHEROS, 0x0018), .driver_data = AR5K_AR5212 }, /* 5212 combatible */ | |
| { PCI_VDEVICE(ATHEROS, 0x0019), .driver_data = AR5K_AR5212 }, /* 5212 combatible */ | |
| { PCI_VDEVICE(ATHEROS, 0x001a), .driver_data = AR5K_AR5212 }, /* 2413 Griffin-lite */ | |
| { PCI_VDEVICE(ATHEROS, 0x001b), .driver_data = AR5K_AR5212 }, /* 5413 Eagle */ | |
| { PCI_VDEVICE(ATHEROS, 0x001c), .driver_data = AR5K_AR5212 }, /* PCI-E cards */ | |
| { PCI_VDEVICE(ATHEROS, 0x001d), .driver_data = AR5K_AR5212 }, /* 2417 Nala */ | |
| { 0 } | |
| }; | |
| MODULE_DEVICE_TABLE(pci, ath5k_pci_id_table); | |
| /* Known SREVs */ | |
| static struct ath5k_srev_name srev_names[] = { | |
| { "5210", AR5K_VERSION_MAC, AR5K_SREV_AR5210 }, | |
| { "5311", AR5K_VERSION_MAC, AR5K_SREV_AR5311 }, | |
| { "5311A", AR5K_VERSION_MAC, AR5K_SREV_AR5311A }, | |
| { "5311B", AR5K_VERSION_MAC, AR5K_SREV_AR5311B }, | |
| { "5211", AR5K_VERSION_MAC, AR5K_SREV_AR5211 }, | |
| { "5212", AR5K_VERSION_MAC, AR5K_SREV_AR5212 }, | |
| { "5213", AR5K_VERSION_MAC, AR5K_SREV_AR5213 }, | |
| { "5213A", AR5K_VERSION_MAC, AR5K_SREV_AR5213A }, | |
| { "2413", AR5K_VERSION_MAC, AR5K_SREV_AR2413 }, | |
| { "2414", AR5K_VERSION_MAC, AR5K_SREV_AR2414 }, | |
| { "5424", AR5K_VERSION_MAC, AR5K_SREV_AR5424 }, | |
| { "5413", AR5K_VERSION_MAC, AR5K_SREV_AR5413 }, | |
| { "5414", AR5K_VERSION_MAC, AR5K_SREV_AR5414 }, | |
| { "2415", AR5K_VERSION_MAC, AR5K_SREV_AR2415 }, | |
| { "5416", AR5K_VERSION_MAC, AR5K_SREV_AR5416 }, | |
| { "5418", AR5K_VERSION_MAC, AR5K_SREV_AR5418 }, | |
| { "2425", AR5K_VERSION_MAC, AR5K_SREV_AR2425 }, | |
| { "2417", AR5K_VERSION_MAC, AR5K_SREV_AR2417 }, | |
| { "xxxxx", AR5K_VERSION_MAC, AR5K_SREV_UNKNOWN }, | |
| { "5110", AR5K_VERSION_RAD, AR5K_SREV_RAD_5110 }, | |
| { "5111", AR5K_VERSION_RAD, AR5K_SREV_RAD_5111 }, | |
| { "5111A", AR5K_VERSION_RAD, AR5K_SREV_RAD_5111A }, | |
| { "2111", AR5K_VERSION_RAD, AR5K_SREV_RAD_2111 }, | |
| { "5112", AR5K_VERSION_RAD, AR5K_SREV_RAD_5112 }, | |
| { "5112A", AR5K_VERSION_RAD, AR5K_SREV_RAD_5112A }, | |
| { "5112B", AR5K_VERSION_RAD, AR5K_SREV_RAD_5112B }, | |
| { "2112", AR5K_VERSION_RAD, AR5K_SREV_RAD_2112 }, | |
| { "2112A", AR5K_VERSION_RAD, AR5K_SREV_RAD_2112A }, | |
| { "2112B", AR5K_VERSION_RAD, AR5K_SREV_RAD_2112B }, | |
| { "2413", AR5K_VERSION_RAD, AR5K_SREV_RAD_2413 }, | |
| { "5413", AR5K_VERSION_RAD, AR5K_SREV_RAD_5413 }, | |
| { "2316", AR5K_VERSION_RAD, AR5K_SREV_RAD_2316 }, | |
| { "2317", AR5K_VERSION_RAD, AR5K_SREV_RAD_2317 }, | |
| { "5424", AR5K_VERSION_RAD, AR5K_SREV_RAD_5424 }, | |
| { "5133", AR5K_VERSION_RAD, AR5K_SREV_RAD_5133 }, | |
| { "xxxxx", AR5K_VERSION_RAD, AR5K_SREV_UNKNOWN }, | |
| }; | |
| static struct ieee80211_rate ath5k_rates[] = { | |
| { .bitrate = 10, | |
| .hw_value = ATH5K_RATE_CODE_1M, }, | |
| { .bitrate = 20, | |
| .hw_value = ATH5K_RATE_CODE_2M, | |
| .hw_value_short = ATH5K_RATE_CODE_2M | AR5K_SET_SHORT_PREAMBLE, | |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, | |
| { .bitrate = 55, | |
| .hw_value = ATH5K_RATE_CODE_5_5M, | |
| .hw_value_short = ATH5K_RATE_CODE_5_5M | AR5K_SET_SHORT_PREAMBLE, | |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, | |
| { .bitrate = 110, | |
| .hw_value = ATH5K_RATE_CODE_11M, | |
| .hw_value_short = ATH5K_RATE_CODE_11M | AR5K_SET_SHORT_PREAMBLE, | |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, | |
| { .bitrate = 60, | |
| .hw_value = ATH5K_RATE_CODE_6M, | |
| .flags = 0 }, | |
| { .bitrate = 90, | |
| .hw_value = ATH5K_RATE_CODE_9M, | |
| .flags = 0 }, | |
| { .bitrate = 120, | |
| .hw_value = ATH5K_RATE_CODE_12M, | |
| .flags = 0 }, | |
| { .bitrate = 180, | |
| .hw_value = ATH5K_RATE_CODE_18M, | |
| .flags = 0 }, | |
| { .bitrate = 240, | |
| .hw_value = ATH5K_RATE_CODE_24M, | |
| .flags = 0 }, | |
| { .bitrate = 360, | |
| .hw_value = ATH5K_RATE_CODE_36M, | |
| .flags = 0 }, | |
| { .bitrate = 480, | |
| .hw_value = ATH5K_RATE_CODE_48M, | |
| .flags = 0 }, | |
| { .bitrate = 540, | |
| .hw_value = ATH5K_RATE_CODE_54M, | |
| .flags = 0 }, | |
| /* XR missing */ | |
| }; | |
| /* | |
| * Prototypes - PCI stack related functions | |
| */ | |
| static int __devinit ath5k_pci_probe(struct pci_dev *pdev, | |
| const struct pci_device_id *id); | |
| static void __devexit ath5k_pci_remove(struct pci_dev *pdev); | |
| #ifdef CONFIG_PM | |
| static int ath5k_pci_suspend(struct pci_dev *pdev, | |
| pm_message_t state); | |
| static int ath5k_pci_resume(struct pci_dev *pdev); | |
| #else | |
| #define ath5k_pci_suspend NULL | |
| #define ath5k_pci_resume NULL | |
| #endif /* CONFIG_PM */ | |
| static struct pci_driver ath5k_pci_driver = { | |
| .name = KBUILD_MODNAME, | |
| .id_table = ath5k_pci_id_table, | |
| .probe = ath5k_pci_probe, | |
| .remove = __devexit_p(ath5k_pci_remove), | |
| .suspend = ath5k_pci_suspend, | |
| .resume = ath5k_pci_resume, | |
| }; | |
| /* | |
| * Prototypes - MAC 802.11 stack related functions | |
| */ | |
| static int ath5k_tx(struct ieee80211_hw *hw, struct sk_buff *skb); | |
| static int ath5k_reset(struct ath5k_softc *sc, bool stop, bool change_channel); | |
| static int ath5k_reset_wake(struct ath5k_softc *sc); | |
| static int ath5k_start(struct ieee80211_hw *hw); | |
| static void ath5k_stop(struct ieee80211_hw *hw); | |
| static int ath5k_add_interface(struct ieee80211_hw *hw, | |
| struct ieee80211_if_init_conf *conf); | |
| static void ath5k_remove_interface(struct ieee80211_hw *hw, | |
| struct ieee80211_if_init_conf *conf); | |
| static int ath5k_config(struct ieee80211_hw *hw, u32 changed); | |
| static int ath5k_config_interface(struct ieee80211_hw *hw, | |
| struct ieee80211_vif *vif, | |
| struct ieee80211_if_conf *conf); | |
| static void ath5k_configure_filter(struct ieee80211_hw *hw, | |
| unsigned int changed_flags, | |
| unsigned int *new_flags, | |
| int mc_count, struct dev_mc_list *mclist); | |
| static int ath5k_set_key(struct ieee80211_hw *hw, | |
| enum set_key_cmd cmd, | |
| const u8 *local_addr, const u8 *addr, | |
| struct ieee80211_key_conf *key); | |
| static int ath5k_get_stats(struct ieee80211_hw *hw, | |
| struct ieee80211_low_level_stats *stats); | |
| static int ath5k_get_tx_stats(struct ieee80211_hw *hw, | |
| struct ieee80211_tx_queue_stats *stats); | |
| static u64 ath5k_get_tsf(struct ieee80211_hw *hw); | |
| static void ath5k_reset_tsf(struct ieee80211_hw *hw); | |
| static int ath5k_beacon_update(struct ath5k_softc *sc, | |
| struct sk_buff *skb); | |
| static void ath5k_bss_info_changed(struct ieee80211_hw *hw, | |
| struct ieee80211_vif *vif, | |
| struct ieee80211_bss_conf *bss_conf, | |
| u32 changes); | |
| static struct ieee80211_ops ath5k_hw_ops = { | |
| .tx = ath5k_tx, | |
| .start = ath5k_start, | |
| .stop = ath5k_stop, | |
| .add_interface = ath5k_add_interface, | |
| .remove_interface = ath5k_remove_interface, | |
| .config = ath5k_config, | |
| .config_interface = ath5k_config_interface, | |
| .configure_filter = ath5k_configure_filter, | |
| .set_key = ath5k_set_key, | |
| .get_stats = ath5k_get_stats, | |
| .conf_tx = NULL, | |
| .get_tx_stats = ath5k_get_tx_stats, | |
| .get_tsf = ath5k_get_tsf, | |
| .reset_tsf = ath5k_reset_tsf, | |
| .bss_info_changed = ath5k_bss_info_changed, | |
| }; | |
| /* | |
| * Prototypes - Internal functions | |
| */ | |
| /* Attach detach */ | |
| static int ath5k_attach(struct pci_dev *pdev, | |
| struct ieee80211_hw *hw); | |
| static void ath5k_detach(struct pci_dev *pdev, | |
| struct ieee80211_hw *hw); | |
| /* Channel/mode setup */ | |
| static inline short ath5k_ieee2mhz(short chan); | |
| static unsigned int ath5k_copy_channels(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channels, | |
| unsigned int mode, | |
| unsigned int max); | |
| static int ath5k_setup_bands(struct ieee80211_hw *hw); | |
| static int ath5k_chan_set(struct ath5k_softc *sc, | |
| struct ieee80211_channel *chan); | |
| static void ath5k_setcurmode(struct ath5k_softc *sc, | |
| unsigned int mode); | |
| static void ath5k_mode_setup(struct ath5k_softc *sc); | |
| /* Descriptor setup */ | |
| static int ath5k_desc_alloc(struct ath5k_softc *sc, | |
| struct pci_dev *pdev); | |
| static void ath5k_desc_free(struct ath5k_softc *sc, | |
| struct pci_dev *pdev); | |
| /* Buffers setup */ | |
| static int ath5k_rxbuf_setup(struct ath5k_softc *sc, | |
| struct ath5k_buf *bf); | |
| static int ath5k_txbuf_setup(struct ath5k_softc *sc, | |
| struct ath5k_buf *bf); | |
| static inline void ath5k_txbuf_free(struct ath5k_softc *sc, | |
| struct ath5k_buf *bf) | |
| { | |
| BUG_ON(!bf); | |
| if (!bf->skb) | |
| return; | |
| pci_unmap_single(sc->pdev, bf->skbaddr, bf->skb->len, | |
| PCI_DMA_TODEVICE); | |
| dev_kfree_skb_any(bf->skb); | |
| bf->skb = NULL; | |
| } | |
| /* Queues setup */ | |
| static struct ath5k_txq *ath5k_txq_setup(struct ath5k_softc *sc, | |
| int qtype, int subtype); | |
| static int ath5k_beaconq_setup(struct ath5k_hw *ah); | |
| static int ath5k_beaconq_config(struct ath5k_softc *sc); | |
| static void ath5k_txq_drainq(struct ath5k_softc *sc, | |
| struct ath5k_txq *txq); | |
| static void ath5k_txq_cleanup(struct ath5k_softc *sc); | |
| static void ath5k_txq_release(struct ath5k_softc *sc); | |
| /* Rx handling */ | |
| static int ath5k_rx_start(struct ath5k_softc *sc); | |
| static void ath5k_rx_stop(struct ath5k_softc *sc); | |
| static unsigned int ath5k_rx_decrypted(struct ath5k_softc *sc, | |
| struct ath5k_desc *ds, | |
| struct sk_buff *skb, | |
| struct ath5k_rx_status *rs); | |
| static void ath5k_tasklet_rx(unsigned long data); | |
| /* Tx handling */ | |
| static void ath5k_tx_processq(struct ath5k_softc *sc, | |
| struct ath5k_txq *txq); | |
| static void ath5k_tasklet_tx(unsigned long data); | |
| /* Beacon handling */ | |
| static int ath5k_beacon_setup(struct ath5k_softc *sc, | |
| struct ath5k_buf *bf); | |
| static void ath5k_beacon_send(struct ath5k_softc *sc); | |
| static void ath5k_beacon_config(struct ath5k_softc *sc); | |
| static void ath5k_beacon_update_timers(struct ath5k_softc *sc, u64 bc_tsf); | |
| static inline u64 ath5k_extend_tsf(struct ath5k_hw *ah, u32 rstamp) | |
| { | |
| u64 tsf = ath5k_hw_get_tsf64(ah); | |
| if ((tsf & 0x7fff) < rstamp) | |
| tsf -= 0x8000; | |
| return (tsf & ~0x7fff) | rstamp; | |
| } | |
| /* Interrupt handling */ | |
| static int ath5k_init(struct ath5k_softc *sc, bool is_resume); | |
| static int ath5k_stop_locked(struct ath5k_softc *sc); | |
| static int ath5k_stop_hw(struct ath5k_softc *sc, bool is_suspend); | |
| static irqreturn_t ath5k_intr(int irq, void *dev_id); | |
| static void ath5k_tasklet_reset(unsigned long data); | |
| static void ath5k_calibrate(unsigned long data); | |
| /* LED functions */ | |
| static int ath5k_init_leds(struct ath5k_softc *sc); | |
| static void ath5k_led_enable(struct ath5k_softc *sc); | |
| static void ath5k_led_off(struct ath5k_softc *sc); | |
| static void ath5k_unregister_leds(struct ath5k_softc *sc); | |
| /* | |
| * Module init/exit functions | |
| */ | |
| static int __init | |
| init_ath5k_pci(void) | |
| { | |
| int ret; | |
| ath5k_debug_init(); | |
| ret = pci_register_driver(&ath5k_pci_driver); | |
| if (ret) { | |
| printk(KERN_ERR "ath5k_pci: can't register pci driver\n"); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static void __exit | |
| exit_ath5k_pci(void) | |
| { | |
| pci_unregister_driver(&ath5k_pci_driver); | |
| ath5k_debug_finish(); | |
| } | |
| module_init(init_ath5k_pci); | |
| module_exit(exit_ath5k_pci); | |
| /********************\ | |
| * PCI Initialization * | |
| \********************/ | |
| static const char * | |
| ath5k_chip_name(enum ath5k_srev_type type, u_int16_t val) | |
| { | |
| const char *name = "xxxxx"; | |
| unsigned int i; | |
| for (i = 0; i < ARRAY_SIZE(srev_names); i++) { | |
| if (srev_names[i].sr_type != type) | |
| continue; | |
| if ((val & 0xf0) == srev_names[i].sr_val) | |
| name = srev_names[i].sr_name; | |
| if ((val & 0xff) == srev_names[i].sr_val) { | |
| name = srev_names[i].sr_name; | |
| break; | |
| } | |
| } | |
| return name; | |
| } | |
| static int __devinit | |
| ath5k_pci_probe(struct pci_dev *pdev, | |
| const struct pci_device_id *id) | |
| { | |
| void __iomem *mem; | |
| struct ath5k_softc *sc; | |
| struct ieee80211_hw *hw; | |
| int ret; | |
| u8 csz; | |
| ret = pci_enable_device(pdev); | |
| if (ret) { | |
| dev_err(&pdev->dev, "can't enable device\n"); | |
| goto err; | |
| } | |
| /* XXX 32-bit addressing only */ | |
| ret = pci_set_dma_mask(pdev, DMA_32BIT_MASK); | |
| if (ret) { | |
| dev_err(&pdev->dev, "32-bit DMA not available\n"); | |
| goto err_dis; | |
| } | |
| /* | |
| * Cache line size is used to size and align various | |
| * structures used to communicate with the hardware. | |
| */ | |
| pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &csz); | |
| if (csz == 0) { | |
| /* | |
| * Linux 2.4.18 (at least) writes the cache line size | |
| * register as a 16-bit wide register which is wrong. | |
| * We must have this setup properly for rx buffer | |
| * DMA to work so force a reasonable value here if it | |
| * comes up zero. | |
| */ | |
| csz = L1_CACHE_BYTES / sizeof(u32); | |
| pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, csz); | |
| } | |
| /* | |
| * The default setting of latency timer yields poor results, | |
| * set it to the value used by other systems. It may be worth | |
| * tweaking this setting more. | |
| */ | |
| pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xa8); | |
| /* Enable bus mastering */ | |
| pci_set_master(pdev); | |
| /* | |
| * Disable the RETRY_TIMEOUT register (0x41) to keep | |
| * PCI Tx retries from interfering with C3 CPU state. | |
| */ | |
| pci_write_config_byte(pdev, 0x41, 0); | |
| ret = pci_request_region(pdev, 0, "ath5k"); | |
| if (ret) { | |
| dev_err(&pdev->dev, "cannot reserve PCI memory region\n"); | |
| goto err_dis; | |
| } | |
| mem = pci_iomap(pdev, 0, 0); | |
| if (!mem) { | |
| dev_err(&pdev->dev, "cannot remap PCI memory region\n") ; | |
| ret = -EIO; | |
| goto err_reg; | |
| } | |
| /* | |
| * Allocate hw (mac80211 main struct) | |
| * and hw->priv (driver private data) | |
| */ | |
| hw = ieee80211_alloc_hw(sizeof(*sc), &ath5k_hw_ops); | |
| if (hw == NULL) { | |
| dev_err(&pdev->dev, "cannot allocate ieee80211_hw\n"); | |
| ret = -ENOMEM; | |
| goto err_map; | |
| } | |
| dev_info(&pdev->dev, "registered as '%s'\n", wiphy_name(hw->wiphy)); | |
| /* Initialize driver private data */ | |
| SET_IEEE80211_DEV(hw, &pdev->dev); | |
| hw->flags = IEEE80211_HW_RX_INCLUDES_FCS | | |
| IEEE80211_HW_SIGNAL_DBM | | |
| IEEE80211_HW_NOISE_DBM; | |
| hw->wiphy->interface_modes = | |
| BIT(NL80211_IFTYPE_STATION) | | |
| BIT(NL80211_IFTYPE_ADHOC) | | |
| BIT(NL80211_IFTYPE_MESH_POINT); | |
| hw->extra_tx_headroom = 2; | |
| hw->channel_change_time = 5000; | |
| sc = hw->priv; | |
| sc->hw = hw; | |
| sc->pdev = pdev; | |
| ath5k_debug_init_device(sc); | |
| /* | |
| * Mark the device as detached to avoid processing | |
| * interrupts until setup is complete. | |
| */ | |
| __set_bit(ATH_STAT_INVALID, sc->status); | |
| sc->iobase = mem; /* So we can unmap it on detach */ | |
| sc->cachelsz = csz * sizeof(u32); /* convert to bytes */ | |
| sc->opmode = NL80211_IFTYPE_STATION; | |
| mutex_init(&sc->lock); | |
| spin_lock_init(&sc->rxbuflock); | |
| spin_lock_init(&sc->txbuflock); | |
| spin_lock_init(&sc->block); | |
| /* Set private data */ | |
| pci_set_drvdata(pdev, hw); | |
| /* Setup interrupt handler */ | |
| ret = request_irq(pdev->irq, ath5k_intr, IRQF_SHARED, "ath", sc); | |
| if (ret) { | |
| ATH5K_ERR(sc, "request_irq failed\n"); | |
| goto err_free; | |
| } | |
| /* Initialize device */ | |
| sc->ah = ath5k_hw_attach(sc, id->driver_data); | |
| if (IS_ERR(sc->ah)) { | |
| ret = PTR_ERR(sc->ah); | |
| goto err_irq; | |
| } | |
| /* set up multi-rate retry capabilities */ | |
| if (sc->ah->ah_version == AR5K_AR5212) { | |
| hw->max_rates = 4; | |
| hw->max_rate_tries = 11; | |
| } | |
| /* Finish private driver data initialization */ | |
| ret = ath5k_attach(pdev, hw); | |
| if (ret) | |
| goto err_ah; | |
| ATH5K_INFO(sc, "Atheros AR%s chip found (MAC: 0x%x, PHY: 0x%x)\n", | |
| ath5k_chip_name(AR5K_VERSION_MAC, sc->ah->ah_mac_srev), | |
| sc->ah->ah_mac_srev, | |
| sc->ah->ah_phy_revision); | |
| if (!sc->ah->ah_single_chip) { | |
| /* Single chip radio (!RF5111) */ | |
| if (sc->ah->ah_radio_5ghz_revision && | |
| !sc->ah->ah_radio_2ghz_revision) { | |
| /* No 5GHz support -> report 2GHz radio */ | |
| if (!test_bit(AR5K_MODE_11A, | |
| sc->ah->ah_capabilities.cap_mode)) { | |
| ATH5K_INFO(sc, "RF%s 2GHz radio found (0x%x)\n", | |
| ath5k_chip_name(AR5K_VERSION_RAD, | |
| sc->ah->ah_radio_5ghz_revision), | |
| sc->ah->ah_radio_5ghz_revision); | |
| /* No 2GHz support (5110 and some | |
| * 5Ghz only cards) -> report 5Ghz radio */ | |
| } else if (!test_bit(AR5K_MODE_11B, | |
| sc->ah->ah_capabilities.cap_mode)) { | |
| ATH5K_INFO(sc, "RF%s 5GHz radio found (0x%x)\n", | |
| ath5k_chip_name(AR5K_VERSION_RAD, | |
| sc->ah->ah_radio_5ghz_revision), | |
| sc->ah->ah_radio_5ghz_revision); | |
| /* Multiband radio */ | |
| } else { | |
| ATH5K_INFO(sc, "RF%s multiband radio found" | |
| " (0x%x)\n", | |
| ath5k_chip_name(AR5K_VERSION_RAD, | |
| sc->ah->ah_radio_5ghz_revision), | |
| sc->ah->ah_radio_5ghz_revision); | |
| } | |
| } | |
| /* Multi chip radio (RF5111 - RF2111) -> | |
| * report both 2GHz/5GHz radios */ | |
| else if (sc->ah->ah_radio_5ghz_revision && | |
| sc->ah->ah_radio_2ghz_revision){ | |
| ATH5K_INFO(sc, "RF%s 5GHz radio found (0x%x)\n", | |
| ath5k_chip_name(AR5K_VERSION_RAD, | |
| sc->ah->ah_radio_5ghz_revision), | |
| sc->ah->ah_radio_5ghz_revision); | |
| ATH5K_INFO(sc, "RF%s 2GHz radio found (0x%x)\n", | |
| ath5k_chip_name(AR5K_VERSION_RAD, | |
| sc->ah->ah_radio_2ghz_revision), | |
| sc->ah->ah_radio_2ghz_revision); | |
| } | |
| } | |
| /* ready to process interrupts */ | |
| __clear_bit(ATH_STAT_INVALID, sc->status); | |
| return 0; | |
| err_ah: | |
| ath5k_hw_detach(sc->ah); | |
| err_irq: | |
| free_irq(pdev->irq, sc); | |
| err_free: | |
| ieee80211_free_hw(hw); | |
| err_map: | |
| pci_iounmap(pdev, mem); | |
| err_reg: | |
| pci_release_region(pdev, 0); | |
| err_dis: | |
| pci_disable_device(pdev); | |
| err: | |
| return ret; | |
| } | |
| static void __devexit | |
| ath5k_pci_remove(struct pci_dev *pdev) | |
| { | |
| struct ieee80211_hw *hw = pci_get_drvdata(pdev); | |
| struct ath5k_softc *sc = hw->priv; | |
| ath5k_debug_finish_device(sc); | |
| ath5k_detach(pdev, hw); | |
| ath5k_hw_detach(sc->ah); | |
| free_irq(pdev->irq, sc); | |
| pci_iounmap(pdev, sc->iobase); | |
| pci_release_region(pdev, 0); | |
| pci_disable_device(pdev); | |
| ieee80211_free_hw(hw); | |
| } | |
| #ifdef CONFIG_PM | |
| static int | |
| ath5k_pci_suspend(struct pci_dev *pdev, pm_message_t state) | |
| { | |
| struct ieee80211_hw *hw = pci_get_drvdata(pdev); | |
| struct ath5k_softc *sc = hw->priv; | |
| ath5k_led_off(sc); | |
| ath5k_stop_hw(sc, true); | |
| free_irq(pdev->irq, sc); | |
| pci_save_state(pdev); | |
| pci_disable_device(pdev); | |
| pci_set_power_state(pdev, PCI_D3hot); | |
| return 0; | |
| } | |
| static int | |
| ath5k_pci_resume(struct pci_dev *pdev) | |
| { | |
| struct ieee80211_hw *hw = pci_get_drvdata(pdev); | |
| struct ath5k_softc *sc = hw->priv; | |
| int err; | |
| pci_restore_state(pdev); | |
| err = pci_enable_device(pdev); | |
| if (err) | |
| return err; | |
| /* | |
| * Suspend/Resume resets the PCI configuration space, so we have to | |
| * re-disable the RETRY_TIMEOUT register (0x41) to keep | |
| * PCI Tx retries from interfering with C3 CPU state | |
| */ | |
| pci_write_config_byte(pdev, 0x41, 0); | |
| err = request_irq(pdev->irq, ath5k_intr, IRQF_SHARED, "ath", sc); | |
| if (err) { | |
| ATH5K_ERR(sc, "request_irq failed\n"); | |
| goto err_no_irq; | |
| } | |
| err = ath5k_init(sc, true); | |
| if (err) | |
| goto err_irq; | |
| ath5k_led_enable(sc); | |
| return 0; | |
| err_irq: | |
| free_irq(pdev->irq, sc); | |
| err_no_irq: | |
| pci_disable_device(pdev); | |
| return err; | |
| } | |
| #endif /* CONFIG_PM */ | |
| /***********************\ | |
| * Driver Initialization * | |
| \***********************/ | |
| static int | |
| ath5k_attach(struct pci_dev *pdev, struct ieee80211_hw *hw) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| struct ath5k_hw *ah = sc->ah; | |
| u8 mac[ETH_ALEN] = {}; | |
| int ret; | |
| ATH5K_DBG(sc, ATH5K_DEBUG_ANY, "devid 0x%x\n", pdev->device); | |
| /* | |
| * Check if the MAC has multi-rate retry support. | |
| * We do this by trying to setup a fake extended | |
| * descriptor. MAC's that don't have support will | |
| * return false w/o doing anything. MAC's that do | |
| * support it will return true w/o doing anything. | |
| */ | |
| ret = ah->ah_setup_mrr_tx_desc(ah, NULL, 0, 0, 0, 0, 0, 0); | |
| if (ret < 0) | |
| goto err; | |
| if (ret > 0) | |
| __set_bit(ATH_STAT_MRRETRY, sc->status); | |
| /* | |
| * Collect the channel list. The 802.11 layer | |
| * is resposible for filtering this list based | |
| * on settings like the phy mode and regulatory | |
| * domain restrictions. | |
| */ | |
| ret = ath5k_setup_bands(hw); | |
| if (ret) { | |
| ATH5K_ERR(sc, "can't get channels\n"); | |
| goto err; | |
| } | |
| /* NB: setup here so ath5k_rate_update is happy */ | |
| if (test_bit(AR5K_MODE_11A, ah->ah_modes)) | |
| ath5k_setcurmode(sc, AR5K_MODE_11A); | |
| else | |
| ath5k_setcurmode(sc, AR5K_MODE_11B); | |
| /* | |
| * Allocate tx+rx descriptors and populate the lists. | |
| */ | |
| ret = ath5k_desc_alloc(sc, pdev); | |
| if (ret) { | |
| ATH5K_ERR(sc, "can't allocate descriptors\n"); | |
| goto err; | |
| } | |
| /* | |
| * Allocate hardware transmit queues: one queue for | |
| * beacon frames and one data queue for each QoS | |
| * priority. Note that hw functions handle reseting | |
| * these queues at the needed time. | |
| */ | |
| ret = ath5k_beaconq_setup(ah); | |
| if (ret < 0) { | |
| ATH5K_ERR(sc, "can't setup a beacon xmit queue\n"); | |
| goto err_desc; | |
| } | |
| sc->bhalq = ret; | |
| sc->txq = ath5k_txq_setup(sc, AR5K_TX_QUEUE_DATA, AR5K_WME_AC_BK); | |
| if (IS_ERR(sc->txq)) { | |
| ATH5K_ERR(sc, "can't setup xmit queue\n"); | |
| ret = PTR_ERR(sc->txq); | |
| goto err_bhal; | |
| } | |
| tasklet_init(&sc->rxtq, ath5k_tasklet_rx, (unsigned long)sc); | |
| tasklet_init(&sc->txtq, ath5k_tasklet_tx, (unsigned long)sc); | |
| tasklet_init(&sc->restq, ath5k_tasklet_reset, (unsigned long)sc); | |
| setup_timer(&sc->calib_tim, ath5k_calibrate, (unsigned long)sc); | |
| ret = ath5k_eeprom_read_mac(ah, mac); | |
| if (ret) { | |
| ATH5K_ERR(sc, "unable to read address from EEPROM: 0x%04x\n", | |
| sc->pdev->device); | |
| goto err_queues; | |
| } | |
| SET_IEEE80211_PERM_ADDR(hw, mac); | |
| /* All MAC address bits matter for ACKs */ | |
| memset(sc->bssidmask, 0xff, ETH_ALEN); | |
| ath5k_hw_set_bssid_mask(sc->ah, sc->bssidmask); | |
| ret = ieee80211_register_hw(hw); | |
| if (ret) { | |
| ATH5K_ERR(sc, "can't register ieee80211 hw\n"); | |
| goto err_queues; | |
| } | |
| ath5k_init_leds(sc); | |
| return 0; | |
| err_queues: | |
| ath5k_txq_release(sc); | |
| err_bhal: | |
| ath5k_hw_release_tx_queue(ah, sc->bhalq); | |
| err_desc: | |
| ath5k_desc_free(sc, pdev); | |
| err: | |
| return ret; | |
| } | |
| static void | |
| ath5k_detach(struct pci_dev *pdev, struct ieee80211_hw *hw) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| /* | |
| * NB: the order of these is important: | |
| * o call the 802.11 layer before detaching ath5k_hw to | |
| * insure callbacks into the driver to delete global | |
| * key cache entries can be handled | |
| * o reclaim the tx queue data structures after calling | |
| * the 802.11 layer as we'll get called back to reclaim | |
| * node state and potentially want to use them | |
| * o to cleanup the tx queues the hal is called, so detach | |
| * it last | |
| * XXX: ??? detach ath5k_hw ??? | |
| * Other than that, it's straightforward... | |
| */ | |
| ieee80211_unregister_hw(hw); | |
| ath5k_desc_free(sc, pdev); | |
| ath5k_txq_release(sc); | |
| ath5k_hw_release_tx_queue(sc->ah, sc->bhalq); | |
| ath5k_unregister_leds(sc); | |
| /* | |
| * NB: can't reclaim these until after ieee80211_ifdetach | |
| * returns because we'll get called back to reclaim node | |
| * state and potentially want to use them. | |
| */ | |
| } | |
| /********************\ | |
| * Channel/mode setup * | |
| \********************/ | |
| /* | |
| * Convert IEEE channel number to MHz frequency. | |
| */ | |
| static inline short | |
| ath5k_ieee2mhz(short chan) | |
| { | |
| if (chan <= 14 || chan >= 27) | |
| return ieee80211chan2mhz(chan); | |
| else | |
| return 2212 + chan * 20; | |
| } | |
| static unsigned int | |
| ath5k_copy_channels(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channels, | |
| unsigned int mode, | |
| unsigned int max) | |
| { | |
| unsigned int i, count, size, chfreq, freq, ch; | |
| if (!test_bit(mode, ah->ah_modes)) | |
| return 0; | |
| switch (mode) { | |
| case AR5K_MODE_11A: | |
| case AR5K_MODE_11A_TURBO: | |
| /* 1..220, but 2GHz frequencies are filtered by check_channel */ | |
| size = 220 ; | |
| chfreq = CHANNEL_5GHZ; | |
| break; | |
| case AR5K_MODE_11B: | |
| case AR5K_MODE_11G: | |
| case AR5K_MODE_11G_TURBO: | |
| size = 26; | |
| chfreq = CHANNEL_2GHZ; | |
| break; | |
| default: | |
| ATH5K_WARN(ah->ah_sc, "bad mode, not copying channels\n"); | |
| return 0; | |
| } | |
| for (i = 0, count = 0; i < size && max > 0; i++) { | |
| ch = i + 1 ; | |
| freq = ath5k_ieee2mhz(ch); | |
| /* Check if channel is supported by the chipset */ | |
| if (!ath5k_channel_ok(ah, freq, chfreq)) | |
| continue; | |
| /* Write channel info and increment counter */ | |
| channels[count].center_freq = freq; | |
| channels[count].band = (chfreq == CHANNEL_2GHZ) ? | |
| IEEE80211_BAND_2GHZ : IEEE80211_BAND_5GHZ; | |
| switch (mode) { | |
| case AR5K_MODE_11A: | |
| case AR5K_MODE_11G: | |
| channels[count].hw_value = chfreq | CHANNEL_OFDM; | |
| break; | |
| case AR5K_MODE_11A_TURBO: | |
| case AR5K_MODE_11G_TURBO: | |
| channels[count].hw_value = chfreq | | |
| CHANNEL_OFDM | CHANNEL_TURBO; | |
| break; | |
| case AR5K_MODE_11B: | |
| channels[count].hw_value = CHANNEL_B; | |
| } | |
| count++; | |
| max--; | |
| } | |
| return count; | |
| } | |
| static void | |
| ath5k_setup_rate_idx(struct ath5k_softc *sc, struct ieee80211_supported_band *b) | |
| { | |
| u8 i; | |
| for (i = 0; i < AR5K_MAX_RATES; i++) | |
| sc->rate_idx[b->band][i] = -1; | |
| for (i = 0; i < b->n_bitrates; i++) { | |
| sc->rate_idx[b->band][b->bitrates[i].hw_value] = i; | |
| if (b->bitrates[i].hw_value_short) | |
| sc->rate_idx[b->band][b->bitrates[i].hw_value_short] = i; | |
| } | |
| } | |
| static int | |
| ath5k_setup_bands(struct ieee80211_hw *hw) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| struct ath5k_hw *ah = sc->ah; | |
| struct ieee80211_supported_band *sband; | |
| int max_c, count_c = 0; | |
| int i; | |
| BUILD_BUG_ON(ARRAY_SIZE(sc->sbands) < IEEE80211_NUM_BANDS); | |
| max_c = ARRAY_SIZE(sc->channels); | |
| /* 2GHz band */ | |
| sband = &sc->sbands[IEEE80211_BAND_2GHZ]; | |
| sband->band = IEEE80211_BAND_2GHZ; | |
| sband->bitrates = &sc->rates[IEEE80211_BAND_2GHZ][0]; | |
| if (test_bit(AR5K_MODE_11G, sc->ah->ah_capabilities.cap_mode)) { | |
| /* G mode */ | |
| memcpy(sband->bitrates, &ath5k_rates[0], | |
| sizeof(struct ieee80211_rate) * 12); | |
| sband->n_bitrates = 12; | |
| sband->channels = sc->channels; | |
| sband->n_channels = ath5k_copy_channels(ah, sband->channels, | |
| AR5K_MODE_11G, max_c); | |
| hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband; | |
| count_c = sband->n_channels; | |
| max_c -= count_c; | |
| } else if (test_bit(AR5K_MODE_11B, sc->ah->ah_capabilities.cap_mode)) { | |
| /* B mode */ | |
| memcpy(sband->bitrates, &ath5k_rates[0], | |
| sizeof(struct ieee80211_rate) * 4); | |
| sband->n_bitrates = 4; | |
| /* 5211 only supports B rates and uses 4bit rate codes | |
| * (e.g normally we have 0x1B for 1M, but on 5211 we have 0x0B) | |
| * fix them up here: | |
| */ | |
| if (ah->ah_version == AR5K_AR5211) { | |
| for (i = 0; i < 4; i++) { | |
| sband->bitrates[i].hw_value = | |
| sband->bitrates[i].hw_value & 0xF; | |
| sband->bitrates[i].hw_value_short = | |
| sband->bitrates[i].hw_value_short & 0xF; | |
| } | |
| } | |
| sband->channels = sc->channels; | |
| sband->n_channels = ath5k_copy_channels(ah, sband->channels, | |
| AR5K_MODE_11B, max_c); | |
| hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband; | |
| count_c = sband->n_channels; | |
| max_c -= count_c; | |
| } | |
| ath5k_setup_rate_idx(sc, sband); | |
| /* 5GHz band, A mode */ | |
| if (test_bit(AR5K_MODE_11A, sc->ah->ah_capabilities.cap_mode)) { | |
| sband = &sc->sbands[IEEE80211_BAND_5GHZ]; | |
| sband->band = IEEE80211_BAND_5GHZ; | |
| sband->bitrates = &sc->rates[IEEE80211_BAND_5GHZ][0]; | |
| memcpy(sband->bitrates, &ath5k_rates[4], | |
| sizeof(struct ieee80211_rate) * 8); | |
| sband->n_bitrates = 8; | |
| sband->channels = &sc->channels[count_c]; | |
| sband->n_channels = ath5k_copy_channels(ah, sband->channels, | |
| AR5K_MODE_11A, max_c); | |
| hw->wiphy->bands[IEEE80211_BAND_5GHZ] = sband; | |
| } | |
| ath5k_setup_rate_idx(sc, sband); | |
| ath5k_debug_dump_bands(sc); | |
| return 0; | |
| } | |
| /* | |
| * Set/change channels. If the channel is really being changed, | |
| * it's done by reseting the chip. To accomplish this we must | |
| * first cleanup any pending DMA, then restart stuff after a la | |
| * ath5k_init. | |
| * | |
| * Called with sc->lock. | |
| */ | |
| static int | |
| ath5k_chan_set(struct ath5k_softc *sc, struct ieee80211_channel *chan) | |
| { | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "(%u MHz) -> (%u MHz)\n", | |
| sc->curchan->center_freq, chan->center_freq); | |
| if (chan->center_freq != sc->curchan->center_freq || | |
| chan->hw_value != sc->curchan->hw_value) { | |
| sc->curchan = chan; | |
| sc->curband = &sc->sbands[chan->band]; | |
| /* | |
| * To switch channels clear any pending DMA operations; | |
| * wait long enough for the RX fifo to drain, reset the | |
| * hardware at the new frequency, and then re-enable | |
| * the relevant bits of the h/w. | |
| */ | |
| return ath5k_reset(sc, true, true); | |
| } | |
| return 0; | |
| } | |
| static void | |
| ath5k_setcurmode(struct ath5k_softc *sc, unsigned int mode) | |
| { | |
| sc->curmode = mode; | |
| if (mode == AR5K_MODE_11A) { | |
| sc->curband = &sc->sbands[IEEE80211_BAND_5GHZ]; | |
| } else { | |
| sc->curband = &sc->sbands[IEEE80211_BAND_2GHZ]; | |
| } | |
| } | |
| static void | |
| ath5k_mode_setup(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| u32 rfilt; | |
| /* configure rx filter */ | |
| rfilt = sc->filter_flags; | |
| ath5k_hw_set_rx_filter(ah, rfilt); | |
| if (ath5k_hw_hasbssidmask(ah)) | |
| ath5k_hw_set_bssid_mask(ah, sc->bssidmask); | |
| /* configure operational mode */ | |
| ath5k_hw_set_opmode(ah); | |
| ath5k_hw_set_mcast_filter(ah, 0, 0); | |
| ATH5K_DBG(sc, ATH5K_DEBUG_MODE, "RX filter 0x%x\n", rfilt); | |
| } | |
| static inline int | |
| ath5k_hw_to_driver_rix(struct ath5k_softc *sc, int hw_rix) | |
| { | |
| WARN_ON(hw_rix < 0 || hw_rix > AR5K_MAX_RATES); | |
| return sc->rate_idx[sc->curband->band][hw_rix]; | |
| } | |
| /***************\ | |
| * Buffers setup * | |
| \***************/ | |
| static | |
| struct sk_buff *ath5k_rx_skb_alloc(struct ath5k_softc *sc, dma_addr_t *skb_addr) | |
| { | |
| struct sk_buff *skb; | |
| unsigned int off; | |
| /* | |
| * Allocate buffer with headroom_needed space for the | |
| * fake physical layer header at the start. | |
| */ | |
| skb = dev_alloc_skb(sc->rxbufsize + sc->cachelsz - 1); | |
| if (!skb) { | |
| ATH5K_ERR(sc, "can't alloc skbuff of size %u\n", | |
| sc->rxbufsize + sc->cachelsz - 1); | |
| return NULL; | |
| } | |
| /* | |
| * Cache-line-align. This is important (for the | |
| * 5210 at least) as not doing so causes bogus data | |
| * in rx'd frames. | |
| */ | |
| off = ((unsigned long)skb->data) % sc->cachelsz; | |
| if (off != 0) | |
| skb_reserve(skb, sc->cachelsz - off); | |
| *skb_addr = pci_map_single(sc->pdev, | |
| skb->data, sc->rxbufsize, PCI_DMA_FROMDEVICE); | |
| if (unlikely(pci_dma_mapping_error(sc->pdev, *skb_addr))) { | |
| ATH5K_ERR(sc, "%s: DMA mapping failed\n", __func__); | |
| dev_kfree_skb(skb); | |
| return NULL; | |
| } | |
| return skb; | |
| } | |
| static int | |
| ath5k_rxbuf_setup(struct ath5k_softc *sc, struct ath5k_buf *bf) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| struct sk_buff *skb = bf->skb; | |
| struct ath5k_desc *ds; | |
| if (!skb) { | |
| skb = ath5k_rx_skb_alloc(sc, &bf->skbaddr); | |
| if (!skb) | |
| return -ENOMEM; | |
| bf->skb = skb; | |
| } | |
| /* | |
| * Setup descriptors. For receive we always terminate | |
| * the descriptor list with a self-linked entry so we'll | |
| * not get overrun under high load (as can happen with a | |
| * 5212 when ANI processing enables PHY error frames). | |
| * | |
| * To insure the last descriptor is self-linked we create | |
| * each descriptor as self-linked and add it to the end. As | |
| * each additional descriptor is added the previous self-linked | |
| * entry is ``fixed'' naturally. This should be safe even | |
| * if DMA is happening. When processing RX interrupts we | |
| * never remove/process the last, self-linked, entry on the | |
| * descriptor list. This insures the hardware always has | |
| * someplace to write a new frame. | |
| */ | |
| ds = bf->desc; | |
| ds->ds_link = bf->daddr; /* link to self */ | |
| ds->ds_data = bf->skbaddr; | |
| ah->ah_setup_rx_desc(ah, ds, | |
| skb_tailroom(skb), /* buffer size */ | |
| 0); | |
| if (sc->rxlink != NULL) | |
| *sc->rxlink = bf->daddr; | |
| sc->rxlink = &ds->ds_link; | |
| return 0; | |
| } | |
| static int | |
| ath5k_txbuf_setup(struct ath5k_softc *sc, struct ath5k_buf *bf) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| struct ath5k_txq *txq = sc->txq; | |
| struct ath5k_desc *ds = bf->desc; | |
| struct sk_buff *skb = bf->skb; | |
| struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); | |
| unsigned int pktlen, flags, keyidx = AR5K_TXKEYIX_INVALID; | |
| struct ieee80211_rate *rate; | |
| unsigned int mrr_rate[3], mrr_tries[3]; | |
| int i, ret; | |
| flags = AR5K_TXDESC_INTREQ | AR5K_TXDESC_CLRDMASK; | |
| /* XXX endianness */ | |
| bf->skbaddr = pci_map_single(sc->pdev, skb->data, skb->len, | |
| PCI_DMA_TODEVICE); | |
| if (info->flags & IEEE80211_TX_CTL_NO_ACK) | |
| flags |= AR5K_TXDESC_NOACK; | |
| pktlen = skb->len; | |
| if (info->control.hw_key) { | |
| keyidx = info->control.hw_key->hw_key_idx; | |
| pktlen += info->control.hw_key->icv_len; | |
| } | |
| ret = ah->ah_setup_tx_desc(ah, ds, pktlen, | |
| ieee80211_get_hdrlen_from_skb(skb), AR5K_PKT_TYPE_NORMAL, | |
| (sc->power_level * 2), | |
| ieee80211_get_tx_rate(sc->hw, info)->hw_value, | |
| info->control.rates[0].count, keyidx, 0, flags, 0, 0); | |
| if (ret) | |
| goto err_unmap; | |
| memset(mrr_rate, 0, sizeof(mrr_rate)); | |
| memset(mrr_tries, 0, sizeof(mrr_tries)); | |
| for (i = 0; i < 3; i++) { | |
| rate = ieee80211_get_alt_retry_rate(sc->hw, info, i); | |
| if (!rate) | |
| break; | |
| mrr_rate[i] = rate->hw_value; | |
| mrr_tries[i] = info->control.rates[i + 1].count; | |
| } | |
| ah->ah_setup_mrr_tx_desc(ah, ds, | |
| mrr_rate[0], mrr_tries[0], | |
| mrr_rate[1], mrr_tries[1], | |
| mrr_rate[2], mrr_tries[2]); | |
| ds->ds_link = 0; | |
| ds->ds_data = bf->skbaddr; | |
| spin_lock_bh(&txq->lock); | |
| list_add_tail(&bf->list, &txq->q); | |
| sc->tx_stats[txq->qnum].len++; | |
| if (txq->link == NULL) /* is this first packet? */ | |
| ath5k_hw_set_txdp(ah, txq->qnum, bf->daddr); | |
| else /* no, so only link it */ | |
| *txq->link = bf->daddr; | |
| txq->link = &ds->ds_link; | |
| ath5k_hw_start_tx_dma(ah, txq->qnum); | |
| mmiowb(); | |
| spin_unlock_bh(&txq->lock); | |
| return 0; | |
| err_unmap: | |
| pci_unmap_single(sc->pdev, bf->skbaddr, skb->len, PCI_DMA_TODEVICE); | |
| return ret; | |
| } | |
| /*******************\ | |
| * Descriptors setup * | |
| \*******************/ | |
| static int | |
| ath5k_desc_alloc(struct ath5k_softc *sc, struct pci_dev *pdev) | |
| { | |
| struct ath5k_desc *ds; | |
| struct ath5k_buf *bf; | |
| dma_addr_t da; | |
| unsigned int i; | |
| int ret; | |
| /* allocate descriptors */ | |
| sc->desc_len = sizeof(struct ath5k_desc) * | |
| (ATH_TXBUF + ATH_RXBUF + ATH_BCBUF + 1); | |
| sc->desc = pci_alloc_consistent(pdev, sc->desc_len, &sc->desc_daddr); | |
| if (sc->desc == NULL) { | |
| ATH5K_ERR(sc, "can't allocate descriptors\n"); | |
| ret = -ENOMEM; | |
| goto err; | |
| } | |
| ds = sc->desc; | |
| da = sc->desc_daddr; | |
| ATH5K_DBG(sc, ATH5K_DEBUG_ANY, "DMA map: %p (%zu) -> %llx\n", | |
| ds, sc->desc_len, (unsigned long long)sc->desc_daddr); | |
| bf = kcalloc(1 + ATH_TXBUF + ATH_RXBUF + ATH_BCBUF, | |
| sizeof(struct ath5k_buf), GFP_KERNEL); | |
| if (bf == NULL) { | |
| ATH5K_ERR(sc, "can't allocate bufptr\n"); | |
| ret = -ENOMEM; | |
| goto err_free; | |
| } | |
| sc->bufptr = bf; | |
| INIT_LIST_HEAD(&sc->rxbuf); | |
| for (i = 0; i < ATH_RXBUF; i++, bf++, ds++, da += sizeof(*ds)) { | |
| bf->desc = ds; | |
| bf->daddr = da; | |
| list_add_tail(&bf->list, &sc->rxbuf); | |
| } | |
| INIT_LIST_HEAD(&sc->txbuf); | |
| sc->txbuf_len = ATH_TXBUF; | |
| for (i = 0; i < ATH_TXBUF; i++, bf++, ds++, | |
| da += sizeof(*ds)) { | |
| bf->desc = ds; | |
| bf->daddr = da; | |
| list_add_tail(&bf->list, &sc->txbuf); | |
| } | |
| /* beacon buffer */ | |
| bf->desc = ds; | |
| bf->daddr = da; | |
| sc->bbuf = bf; | |
| return 0; | |
| err_free: | |
| pci_free_consistent(pdev, sc->desc_len, sc->desc, sc->desc_daddr); | |
| err: | |
| sc->desc = NULL; | |
| return ret; | |
| } | |
| static void | |
| ath5k_desc_free(struct ath5k_softc *sc, struct pci_dev *pdev) | |
| { | |
| struct ath5k_buf *bf; | |
| ath5k_txbuf_free(sc, sc->bbuf); | |
| list_for_each_entry(bf, &sc->txbuf, list) | |
| ath5k_txbuf_free(sc, bf); | |
| list_for_each_entry(bf, &sc->rxbuf, list) | |
| ath5k_txbuf_free(sc, bf); | |
| /* Free memory associated with all descriptors */ | |
| pci_free_consistent(pdev, sc->desc_len, sc->desc, sc->desc_daddr); | |
| kfree(sc->bufptr); | |
| sc->bufptr = NULL; | |
| } | |
| /**************\ | |
| * Queues setup * | |
| \**************/ | |
| static struct ath5k_txq * | |
| ath5k_txq_setup(struct ath5k_softc *sc, | |
| int qtype, int subtype) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| struct ath5k_txq *txq; | |
| struct ath5k_txq_info qi = { | |
| .tqi_subtype = subtype, | |
| .tqi_aifs = AR5K_TXQ_USEDEFAULT, | |
| .tqi_cw_min = AR5K_TXQ_USEDEFAULT, | |
| .tqi_cw_max = AR5K_TXQ_USEDEFAULT | |
| }; | |
| int qnum; | |
| /* | |
| * Enable interrupts only for EOL and DESC conditions. | |
| * We mark tx descriptors to receive a DESC interrupt | |
| * when a tx queue gets deep; otherwise waiting for the | |
| * EOL to reap descriptors. Note that this is done to | |
| * reduce interrupt load and this only defers reaping | |
| * descriptors, never transmitting frames. Aside from | |
| * reducing interrupts this also permits more concurrency. | |
| * The only potential downside is if the tx queue backs | |
| * up in which case the top half of the kernel may backup | |
| * due to a lack of tx descriptors. | |
| */ | |
| qi.tqi_flags = AR5K_TXQ_FLAG_TXEOLINT_ENABLE | | |
| AR5K_TXQ_FLAG_TXDESCINT_ENABLE; | |
| qnum = ath5k_hw_setup_tx_queue(ah, qtype, &qi); | |
| if (qnum < 0) { | |
| /* | |
| * NB: don't print a message, this happens | |
| * normally on parts with too few tx queues | |
| */ | |
| return ERR_PTR(qnum); | |
| } | |
| if (qnum >= ARRAY_SIZE(sc->txqs)) { | |
| ATH5K_ERR(sc, "hw qnum %u out of range, max %tu!\n", | |
| qnum, ARRAY_SIZE(sc->txqs)); | |
| ath5k_hw_release_tx_queue(ah, qnum); | |
| return ERR_PTR(-EINVAL); | |
| } | |
| txq = &sc->txqs[qnum]; | |
| if (!txq->setup) { | |
| txq->qnum = qnum; | |
| txq->link = NULL; | |
| INIT_LIST_HEAD(&txq->q); | |
| spin_lock_init(&txq->lock); | |
| txq->setup = true; | |
| } | |
| return &sc->txqs[qnum]; | |
| } | |
| static int | |
| ath5k_beaconq_setup(struct ath5k_hw *ah) | |
| { | |
| struct ath5k_txq_info qi = { | |
| .tqi_aifs = AR5K_TXQ_USEDEFAULT, | |
| .tqi_cw_min = AR5K_TXQ_USEDEFAULT, | |
| .tqi_cw_max = AR5K_TXQ_USEDEFAULT, | |
| /* NB: for dynamic turbo, don't enable any other interrupts */ | |
| .tqi_flags = AR5K_TXQ_FLAG_TXDESCINT_ENABLE | |
| }; | |
| return ath5k_hw_setup_tx_queue(ah, AR5K_TX_QUEUE_BEACON, &qi); | |
| } | |
| static int | |
| ath5k_beaconq_config(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| struct ath5k_txq_info qi; | |
| int ret; | |
| ret = ath5k_hw_get_tx_queueprops(ah, sc->bhalq, &qi); | |
| if (ret) | |
| return ret; | |
| if (sc->opmode == NL80211_IFTYPE_AP || | |
| sc->opmode == NL80211_IFTYPE_MESH_POINT) { | |
| /* | |
| * Always burst out beacon and CAB traffic | |
| * (aifs = cwmin = cwmax = 0) | |
| */ | |
| qi.tqi_aifs = 0; | |
| qi.tqi_cw_min = 0; | |
| qi.tqi_cw_max = 0; | |
| } else if (sc->opmode == NL80211_IFTYPE_ADHOC) { | |
| /* | |
| * Adhoc mode; backoff between 0 and (2 * cw_min). | |
| */ | |
| qi.tqi_aifs = 0; | |
| qi.tqi_cw_min = 0; | |
| qi.tqi_cw_max = 2 * ah->ah_cw_min; | |
| } | |
| ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, | |
| "beacon queueprops tqi_aifs:%d tqi_cw_min:%d tqi_cw_max:%d\n", | |
| qi.tqi_aifs, qi.tqi_cw_min, qi.tqi_cw_max); | |
| ret = ath5k_hw_set_tx_queueprops(ah, sc->bhalq, &qi); | |
| if (ret) { | |
| ATH5K_ERR(sc, "%s: unable to update parameters for beacon " | |
| "hardware queue!\n", __func__); | |
| return ret; | |
| } | |
| return ath5k_hw_reset_tx_queue(ah, sc->bhalq); /* push to h/w */; | |
| } | |
| static void | |
| ath5k_txq_drainq(struct ath5k_softc *sc, struct ath5k_txq *txq) | |
| { | |
| struct ath5k_buf *bf, *bf0; | |
| /* | |
| * NB: this assumes output has been stopped and | |
| * we do not need to block ath5k_tx_tasklet | |
| */ | |
| spin_lock_bh(&txq->lock); | |
| list_for_each_entry_safe(bf, bf0, &txq->q, list) { | |
| ath5k_debug_printtxbuf(sc, bf); | |
| ath5k_txbuf_free(sc, bf); | |
| spin_lock_bh(&sc->txbuflock); | |
| sc->tx_stats[txq->qnum].len--; | |
| list_move_tail(&bf->list, &sc->txbuf); | |
| sc->txbuf_len++; | |
| spin_unlock_bh(&sc->txbuflock); | |
| } | |
| txq->link = NULL; | |
| spin_unlock_bh(&txq->lock); | |
| } | |
| /* | |
| * Drain the transmit queues and reclaim resources. | |
| */ | |
| static void | |
| ath5k_txq_cleanup(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| unsigned int i; | |
| /* XXX return value */ | |
| if (likely(!test_bit(ATH_STAT_INVALID, sc->status))) { | |
| /* don't touch the hardware if marked invalid */ | |
| ath5k_hw_stop_tx_dma(ah, sc->bhalq); | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "beacon queue %x\n", | |
| ath5k_hw_get_txdp(ah, sc->bhalq)); | |
| for (i = 0; i < ARRAY_SIZE(sc->txqs); i++) | |
| if (sc->txqs[i].setup) { | |
| ath5k_hw_stop_tx_dma(ah, sc->txqs[i].qnum); | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "txq [%u] %x, " | |
| "link %p\n", | |
| sc->txqs[i].qnum, | |
| ath5k_hw_get_txdp(ah, | |
| sc->txqs[i].qnum), | |
| sc->txqs[i].link); | |
| } | |
| } | |
| ieee80211_wake_queues(sc->hw); /* XXX move to callers */ | |
| for (i = 0; i < ARRAY_SIZE(sc->txqs); i++) | |
| if (sc->txqs[i].setup) | |
| ath5k_txq_drainq(sc, &sc->txqs[i]); | |
| } | |
| static void | |
| ath5k_txq_release(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_txq *txq = sc->txqs; | |
| unsigned int i; | |
| for (i = 0; i < ARRAY_SIZE(sc->txqs); i++, txq++) | |
| if (txq->setup) { | |
| ath5k_hw_release_tx_queue(sc->ah, txq->qnum); | |
| txq->setup = false; | |
| } | |
| } | |
| /*************\ | |
| * RX Handling * | |
| \*************/ | |
| /* | |
| * Enable the receive h/w following a reset. | |
| */ | |
| static int | |
| ath5k_rx_start(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| struct ath5k_buf *bf; | |
| int ret; | |
| sc->rxbufsize = roundup(IEEE80211_MAX_LEN, sc->cachelsz); | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "cachelsz %u rxbufsize %u\n", | |
| sc->cachelsz, sc->rxbufsize); | |
| sc->rxlink = NULL; | |
| spin_lock_bh(&sc->rxbuflock); | |
| list_for_each_entry(bf, &sc->rxbuf, list) { | |
| ret = ath5k_rxbuf_setup(sc, bf); | |
| if (ret != 0) { | |
| spin_unlock_bh(&sc->rxbuflock); | |
| goto err; | |
| } | |
| } | |
| bf = list_first_entry(&sc->rxbuf, struct ath5k_buf, list); | |
| spin_unlock_bh(&sc->rxbuflock); | |
| ath5k_hw_set_rxdp(ah, bf->daddr); | |
| ath5k_hw_start_rx_dma(ah); /* enable recv descriptors */ | |
| ath5k_mode_setup(sc); /* set filters, etc. */ | |
| ath5k_hw_start_rx_pcu(ah); /* re-enable PCU/DMA engine */ | |
| return 0; | |
| err: | |
| return ret; | |
| } | |
| /* | |
| * Disable the receive h/w in preparation for a reset. | |
| */ | |
| static void | |
| ath5k_rx_stop(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| ath5k_hw_stop_rx_pcu(ah); /* disable PCU */ | |
| ath5k_hw_set_rx_filter(ah, 0); /* clear recv filter */ | |
| ath5k_hw_stop_rx_dma(ah); /* disable DMA engine */ | |
| ath5k_debug_printrxbuffs(sc, ah); | |
| sc->rxlink = NULL; /* just in case */ | |
| } | |
| static unsigned int | |
| ath5k_rx_decrypted(struct ath5k_softc *sc, struct ath5k_desc *ds, | |
| struct sk_buff *skb, struct ath5k_rx_status *rs) | |
| { | |
| struct ieee80211_hdr *hdr = (void *)skb->data; | |
| unsigned int keyix, hlen; | |
| if (!(rs->rs_status & AR5K_RXERR_DECRYPT) && | |
| rs->rs_keyix != AR5K_RXKEYIX_INVALID) | |
| return RX_FLAG_DECRYPTED; | |
| /* Apparently when a default key is used to decrypt the packet | |
| the hw does not set the index used to decrypt. In such cases | |
| get the index from the packet. */ | |
| hlen = ieee80211_hdrlen(hdr->frame_control); | |
| if (ieee80211_has_protected(hdr->frame_control) && | |
| !(rs->rs_status & AR5K_RXERR_DECRYPT) && | |
| skb->len >= hlen + 4) { | |
| keyix = skb->data[hlen + 3] >> 6; | |
| if (test_bit(keyix, sc->keymap)) | |
| return RX_FLAG_DECRYPTED; | |
| } | |
| return 0; | |
| } | |
| static void | |
| ath5k_check_ibss_tsf(struct ath5k_softc *sc, struct sk_buff *skb, | |
| struct ieee80211_rx_status *rxs) | |
| { | |
| u64 tsf, bc_tstamp; | |
| u32 hw_tu; | |
| struct ieee80211_mgmt *mgmt = (struct ieee80211_mgmt *)skb->data; | |
| if (ieee80211_is_beacon(mgmt->frame_control) && | |
| le16_to_cpu(mgmt->u.beacon.capab_info) & WLAN_CAPABILITY_IBSS && | |
| memcmp(mgmt->bssid, sc->ah->ah_bssid, ETH_ALEN) == 0) { | |
| /* | |
| * Received an IBSS beacon with the same BSSID. Hardware *must* | |
| * have updated the local TSF. We have to work around various | |
| * hardware bugs, though... | |
| */ | |
| tsf = ath5k_hw_get_tsf64(sc->ah); | |
| bc_tstamp = le64_to_cpu(mgmt->u.beacon.timestamp); | |
| hw_tu = TSF_TO_TU(tsf); | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, | |
| "beacon %llx mactime %llx (diff %lld) tsf now %llx\n", | |
| (unsigned long long)bc_tstamp, | |
| (unsigned long long)rxs->mactime, | |
| (unsigned long long)(rxs->mactime - bc_tstamp), | |
| (unsigned long long)tsf); | |
| /* | |
| * Sometimes the HW will give us a wrong tstamp in the rx | |
| * status, causing the timestamp extension to go wrong. | |
| * (This seems to happen especially with beacon frames bigger | |
| * than 78 byte (incl. FCS)) | |
| * But we know that the receive timestamp must be later than the | |
| * timestamp of the beacon since HW must have synced to that. | |
| * | |
| * NOTE: here we assume mactime to be after the frame was | |
| * received, not like mac80211 which defines it at the start. | |
| */ | |
| if (bc_tstamp > rxs->mactime) { | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, | |
| "fixing mactime from %llx to %llx\n", | |
| (unsigned long long)rxs->mactime, | |
| (unsigned long long)tsf); | |
| rxs->mactime = tsf; | |
| } | |
| /* | |
| * Local TSF might have moved higher than our beacon timers, | |
| * in that case we have to update them to continue sending | |
| * beacons. This also takes care of synchronizing beacon sending | |
| * times with other stations. | |
| */ | |
| if (hw_tu >= sc->nexttbtt) | |
| ath5k_beacon_update_timers(sc, bc_tstamp); | |
| } | |
| } | |
| static void | |
| ath5k_tasklet_rx(unsigned long data) | |
| { | |
| struct ieee80211_rx_status rxs = {}; | |
| struct ath5k_rx_status rs = {}; | |
| struct sk_buff *skb, *next_skb; | |
| dma_addr_t next_skb_addr; | |
| struct ath5k_softc *sc = (void *)data; | |
| struct ath5k_buf *bf, *bf_last; | |
| struct ath5k_desc *ds; | |
| int ret; | |
| int hdrlen; | |
| int padsize; | |
| spin_lock(&sc->rxbuflock); | |
| if (list_empty(&sc->rxbuf)) { | |
| ATH5K_WARN(sc, "empty rx buf pool\n"); | |
| goto unlock; | |
| } | |
| bf_last = list_entry(sc->rxbuf.prev, struct ath5k_buf, list); | |
| do { | |
| rxs.flag = 0; | |
| bf = list_first_entry(&sc->rxbuf, struct ath5k_buf, list); | |
| BUG_ON(bf->skb == NULL); | |
| skb = bf->skb; | |
| ds = bf->desc; | |
| /* | |
| * last buffer must not be freed to ensure proper hardware | |
| * function. When the hardware finishes also a packet next to | |
| * it, we are sure, it doesn't use it anymore and we can go on. | |
| */ | |
| if (bf_last == bf) | |
| bf->flags |= 1; | |
| if (bf->flags) { | |
| struct ath5k_buf *bf_next = list_entry(bf->list.next, | |
| struct ath5k_buf, list); | |
| ret = sc->ah->ah_proc_rx_desc(sc->ah, bf_next->desc, | |
| &rs); | |
| if (ret) | |
| break; | |
| bf->flags &= ~1; | |
| /* skip the overwritten one (even status is martian) */ | |
| goto next; | |
| } | |
| ret = sc->ah->ah_proc_rx_desc(sc->ah, ds, &rs); | |
| if (unlikely(ret == -EINPROGRESS)) | |
| break; | |
| else if (unlikely(ret)) { | |
| ATH5K_ERR(sc, "error in processing rx descriptor\n"); | |
| spin_unlock(&sc->rxbuflock); | |
| return; | |
| } | |
| if (unlikely(rs.rs_more)) { | |
| ATH5K_WARN(sc, "unsupported jumbo\n"); | |
| goto next; | |
| } | |
| if (unlikely(rs.rs_status)) { | |
| if (rs.rs_status & AR5K_RXERR_PHY) | |
| goto next; | |
| if (rs.rs_status & AR5K_RXERR_DECRYPT) { | |
| /* | |
| * Decrypt error. If the error occurred | |
| * because there was no hardware key, then | |
| * let the frame through so the upper layers | |
| * can process it. This is necessary for 5210 | |
| * parts which have no way to setup a ``clear'' | |
| * key cache entry. | |
| * | |
| * XXX do key cache faulting | |
| */ | |
| if (rs.rs_keyix == AR5K_RXKEYIX_INVALID && | |
| !(rs.rs_status & AR5K_RXERR_CRC)) | |
| goto accept; | |
| } | |
| if (rs.rs_status & AR5K_RXERR_MIC) { | |
| rxs.flag |= RX_FLAG_MMIC_ERROR; | |
| goto accept; | |
| } | |
| /* let crypto-error packets fall through in MNTR */ | |
| if ((rs.rs_status & | |
| ~(AR5K_RXERR_DECRYPT|AR5K_RXERR_MIC)) || | |
| sc->opmode != NL80211_IFTYPE_MONITOR) | |
| goto next; | |
| } | |
| accept: | |
| next_skb = ath5k_rx_skb_alloc(sc, &next_skb_addr); | |
| /* | |
| * If we can't replace bf->skb with a new skb under memory | |
| * pressure, just skip this packet | |
| */ | |
| if (!next_skb) | |
| goto next; | |
| pci_unmap_single(sc->pdev, bf->skbaddr, sc->rxbufsize, | |
| PCI_DMA_FROMDEVICE); | |
| skb_put(skb, rs.rs_datalen); | |
| /* The MAC header is padded to have 32-bit boundary if the | |
| * packet payload is non-zero. The general calculation for | |
| * padsize would take into account odd header lengths: | |
| * padsize = (4 - hdrlen % 4) % 4; However, since only | |
| * even-length headers are used, padding can only be 0 or 2 | |
| * bytes and we can optimize this a bit. In addition, we must | |
| * not try to remove padding from short control frames that do | |
| * not have payload. */ | |
| hdrlen = ieee80211_get_hdrlen_from_skb(skb); | |
| padsize = ath5k_pad_size(hdrlen); | |
| if (padsize) { | |
| memmove(skb->data + padsize, skb->data, hdrlen); | |
| skb_pull(skb, padsize); | |
| } | |
| /* | |
| * always extend the mac timestamp, since this information is | |
| * also needed for proper IBSS merging. | |
| * | |
| * XXX: it might be too late to do it here, since rs_tstamp is | |
| * 15bit only. that means TSF extension has to be done within | |
| * 32768usec (about 32ms). it might be necessary to move this to | |
| * the interrupt handler, like it is done in madwifi. | |
| * | |
| * Unfortunately we don't know when the hardware takes the rx | |
| * timestamp (beginning of phy frame, data frame, end of rx?). | |
| * The only thing we know is that it is hardware specific... | |
| * On AR5213 it seems the rx timestamp is at the end of the | |
| * frame, but i'm not sure. | |
| * | |
| * NOTE: mac80211 defines mactime at the beginning of the first | |
| * data symbol. Since we don't have any time references it's | |
| * impossible to comply to that. This affects IBSS merge only | |
| * right now, so it's not too bad... | |
| */ | |
| rxs.mactime = ath5k_extend_tsf(sc->ah, rs.rs_tstamp); | |
| rxs.flag |= RX_FLAG_TSFT; | |
| rxs.freq = sc->curchan->center_freq; | |
| rxs.band = sc->curband->band; | |
| rxs.noise = sc->ah->ah_noise_floor; | |
| rxs.signal = rxs.noise + rs.rs_rssi; | |
| /* An rssi of 35 indicates you should be able use | |
| * 54 Mbps reliably. A more elaborate scheme can be used | |
| * here but it requires a map of SNR/throughput for each | |
| * possible mode used */ | |
| rxs.qual = rs.rs_rssi * 100 / 35; | |
| /* rssi can be more than 35 though, anything above that | |
| * should be considered at 100% */ | |
| if (rxs.qual > 100) | |
| rxs.qual = 100; | |
| rxs.antenna = rs.rs_antenna; | |
| rxs.rate_idx = ath5k_hw_to_driver_rix(sc, rs.rs_rate); | |
| rxs.flag |= ath5k_rx_decrypted(sc, ds, skb, &rs); | |
| if (rxs.rate_idx >= 0 && rs.rs_rate == | |
| sc->curband->bitrates[rxs.rate_idx].hw_value_short) | |
| rxs.flag |= RX_FLAG_SHORTPRE; | |
| ath5k_debug_dump_skb(sc, skb, "RX ", 0); | |
| /* check beacons in IBSS mode */ | |
| if (sc->opmode == NL80211_IFTYPE_ADHOC) | |
| ath5k_check_ibss_tsf(sc, skb, &rxs); | |
| __ieee80211_rx(sc->hw, skb, &rxs); | |
| bf->skb = next_skb; | |
| bf->skbaddr = next_skb_addr; | |
| next: | |
| list_move_tail(&bf->list, &sc->rxbuf); | |
| } while (ath5k_rxbuf_setup(sc, bf) == 0); | |
| unlock: | |
| spin_unlock(&sc->rxbuflock); | |
| } | |
| /*************\ | |
| * TX Handling * | |
| \*************/ | |
| static void | |
| ath5k_tx_processq(struct ath5k_softc *sc, struct ath5k_txq *txq) | |
| { | |
| struct ath5k_tx_status ts = {}; | |
| struct ath5k_buf *bf, *bf0; | |
| struct ath5k_desc *ds; | |
| struct sk_buff *skb; | |
| struct ieee80211_tx_info *info; | |
| int i, ret; | |
| spin_lock(&txq->lock); | |
| list_for_each_entry_safe(bf, bf0, &txq->q, list) { | |
| ds = bf->desc; | |
| ret = sc->ah->ah_proc_tx_desc(sc->ah, ds, &ts); | |
| if (unlikely(ret == -EINPROGRESS)) | |
| break; | |
| else if (unlikely(ret)) { | |
| ATH5K_ERR(sc, "error %d while processing queue %u\n", | |
| ret, txq->qnum); | |
| break; | |
| } | |
| skb = bf->skb; | |
| info = IEEE80211_SKB_CB(skb); | |
| bf->skb = NULL; | |
| pci_unmap_single(sc->pdev, bf->skbaddr, skb->len, | |
| PCI_DMA_TODEVICE); | |
| ieee80211_tx_info_clear_status(info); | |
| for (i = 0; i < 4; i++) { | |
| struct ieee80211_tx_rate *r = | |
| &info->status.rates[i]; | |
| if (ts.ts_rate[i]) { | |
| r->idx = ath5k_hw_to_driver_rix(sc, ts.ts_rate[i]); | |
| r->count = ts.ts_retry[i]; | |
| } else { | |
| r->idx = -1; | |
| r->count = 0; | |
| } | |
| } | |
| /* count the successful attempt as well */ | |
| info->status.rates[ts.ts_final_idx].count++; | |
| if (unlikely(ts.ts_status)) { | |
| sc->ll_stats.dot11ACKFailureCount++; | |
| if (ts.ts_status & AR5K_TXERR_FILT) | |
| info->flags |= IEEE80211_TX_STAT_TX_FILTERED; | |
| } else { | |
| info->flags |= IEEE80211_TX_STAT_ACK; | |
| info->status.ack_signal = ts.ts_rssi; | |
| } | |
| ieee80211_tx_status(sc->hw, skb); | |
| sc->tx_stats[txq->qnum].count++; | |
| spin_lock(&sc->txbuflock); | |
| sc->tx_stats[txq->qnum].len--; | |
| list_move_tail(&bf->list, &sc->txbuf); | |
| sc->txbuf_len++; | |
| spin_unlock(&sc->txbuflock); | |
| } | |
| if (likely(list_empty(&txq->q))) | |
| txq->link = NULL; | |
| spin_unlock(&txq->lock); | |
| if (sc->txbuf_len > ATH_TXBUF / 5) | |
| ieee80211_wake_queues(sc->hw); | |
| } | |
| static void | |
| ath5k_tasklet_tx(unsigned long data) | |
| { | |
| struct ath5k_softc *sc = (void *)data; | |
| ath5k_tx_processq(sc, sc->txq); | |
| } | |
| /*****************\ | |
| * Beacon handling * | |
| \*****************/ | |
| /* | |
| * Setup the beacon frame for transmit. | |
| */ | |
| static int | |
| ath5k_beacon_setup(struct ath5k_softc *sc, struct ath5k_buf *bf) | |
| { | |
| struct sk_buff *skb = bf->skb; | |
| struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); | |
| struct ath5k_hw *ah = sc->ah; | |
| struct ath5k_desc *ds; | |
| int ret, antenna = 0; | |
| u32 flags; | |
| bf->skbaddr = pci_map_single(sc->pdev, skb->data, skb->len, | |
| PCI_DMA_TODEVICE); | |
| ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "skb %p [data %p len %u] " | |
| "skbaddr %llx\n", skb, skb->data, skb->len, | |
| (unsigned long long)bf->skbaddr); | |
| if (pci_dma_mapping_error(sc->pdev, bf->skbaddr)) { | |
| ATH5K_ERR(sc, "beacon DMA mapping failed\n"); | |
| return -EIO; | |
| } | |
| ds = bf->desc; | |
| flags = AR5K_TXDESC_NOACK; | |
| if (sc->opmode == NL80211_IFTYPE_ADHOC && ath5k_hw_hasveol(ah)) { | |
| ds->ds_link = bf->daddr; /* self-linked */ | |
| flags |= AR5K_TXDESC_VEOL; | |
| /* | |
| * Let hardware handle antenna switching if txantenna is not set | |
| */ | |
| } else { | |
| ds->ds_link = 0; | |
| /* | |
| * Switch antenna every 4 beacons if txantenna is not set | |
| * XXX assumes two antennas | |
| */ | |
| if (antenna == 0) | |
| antenna = sc->bsent & 4 ? 2 : 1; | |
| } | |
| ds->ds_data = bf->skbaddr; | |
| ret = ah->ah_setup_tx_desc(ah, ds, skb->len, | |
| ieee80211_get_hdrlen_from_skb(skb), | |
| AR5K_PKT_TYPE_BEACON, (sc->power_level * 2), | |
| ieee80211_get_tx_rate(sc->hw, info)->hw_value, | |
| 1, AR5K_TXKEYIX_INVALID, | |
| antenna, flags, 0, 0); | |
| if (ret) | |
| goto err_unmap; | |
| return 0; | |
| err_unmap: | |
| pci_unmap_single(sc->pdev, bf->skbaddr, skb->len, PCI_DMA_TODEVICE); | |
| return ret; | |
| } | |
| /* | |
| * Transmit a beacon frame at SWBA. Dynamic updates to the | |
| * frame contents are done as needed and the slot time is | |
| * also adjusted based on current state. | |
| * | |
| * this is usually called from interrupt context (ath5k_intr()) | |
| * but also from ath5k_beacon_config() in IBSS mode which in turn | |
| * can be called from a tasklet and user context | |
| */ | |
| static void | |
| ath5k_beacon_send(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_buf *bf = sc->bbuf; | |
| struct ath5k_hw *ah = sc->ah; | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "in beacon_send\n"); | |
| if (unlikely(bf->skb == NULL || sc->opmode == NL80211_IFTYPE_STATION || | |
| sc->opmode == NL80211_IFTYPE_MONITOR)) { | |
| ATH5K_WARN(sc, "bf=%p bf_skb=%p\n", bf, bf ? bf->skb : NULL); | |
| return; | |
| } | |
| /* | |
| * Check if the previous beacon has gone out. If | |
| * not don't don't try to post another, skip this | |
| * period and wait for the next. Missed beacons | |
| * indicate a problem and should not occur. If we | |
| * miss too many consecutive beacons reset the device. | |
| */ | |
| if (unlikely(ath5k_hw_num_tx_pending(ah, sc->bhalq) != 0)) { | |
| sc->bmisscount++; | |
| ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, | |
| "missed %u consecutive beacons\n", sc->bmisscount); | |
| if (sc->bmisscount > 3) { /* NB: 3 is a guess */ | |
| ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, | |
| "stuck beacon time (%u missed)\n", | |
| sc->bmisscount); | |
| tasklet_schedule(&sc->restq); | |
| } | |
| return; | |
| } | |
| if (unlikely(sc->bmisscount != 0)) { | |
| ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, | |
| "resume beacon xmit after %u misses\n", | |
| sc->bmisscount); | |
| sc->bmisscount = 0; | |
| } | |
| /* | |
| * Stop any current dma and put the new frame on the queue. | |
| * This should never fail since we check above that no frames | |
| * are still pending on the queue. | |
| */ | |
| if (unlikely(ath5k_hw_stop_tx_dma(ah, sc->bhalq))) { | |
| ATH5K_WARN(sc, "beacon queue %u didn't stop?\n", sc->bhalq); | |
| /* NB: hw still stops DMA, so proceed */ | |
| } | |
| ath5k_hw_set_txdp(ah, sc->bhalq, bf->daddr); | |
| ath5k_hw_start_tx_dma(ah, sc->bhalq); | |
| ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "TXDP[%u] = %llx (%p)\n", | |
| sc->bhalq, (unsigned long long)bf->daddr, bf->desc); | |
| sc->bsent++; | |
| } | |
| /** | |
| * ath5k_beacon_update_timers - update beacon timers | |
| * | |
| * @sc: struct ath5k_softc pointer we are operating on | |
| * @bc_tsf: the timestamp of the beacon. 0 to reset the TSF. -1 to perform a | |
| * beacon timer update based on the current HW TSF. | |
| * | |
| * Calculate the next target beacon transmit time (TBTT) based on the timestamp | |
| * of a received beacon or the current local hardware TSF and write it to the | |
| * beacon timer registers. | |
| * | |
| * This is called in a variety of situations, e.g. when a beacon is received, | |
| * when a TSF update has been detected, but also when an new IBSS is created or | |
| * when we otherwise know we have to update the timers, but we keep it in this | |
| * function to have it all together in one place. | |
| */ | |
| static void | |
| ath5k_beacon_update_timers(struct ath5k_softc *sc, u64 bc_tsf) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| u32 nexttbtt, intval, hw_tu, bc_tu; | |
| u64 hw_tsf; | |
| intval = sc->bintval & AR5K_BEACON_PERIOD; | |
| if (WARN_ON(!intval)) | |
| return; | |
| /* beacon TSF converted to TU */ | |
| bc_tu = TSF_TO_TU(bc_tsf); | |
| /* current TSF converted to TU */ | |
| hw_tsf = ath5k_hw_get_tsf64(ah); | |
| hw_tu = TSF_TO_TU(hw_tsf); | |
| #define FUDGE 3 | |
| /* we use FUDGE to make sure the next TBTT is ahead of the current TU */ | |
| if (bc_tsf == -1) { | |
| /* | |
| * no beacons received, called internally. | |
| * just need to refresh timers based on HW TSF. | |
| */ | |
| nexttbtt = roundup(hw_tu + FUDGE, intval); | |
| } else if (bc_tsf == 0) { | |
| /* | |
| * no beacon received, probably called by ath5k_reset_tsf(). | |
| * reset TSF to start with 0. | |
| */ | |
| nexttbtt = intval; | |
| intval |= AR5K_BEACON_RESET_TSF; | |
| } else if (bc_tsf > hw_tsf) { | |
| /* | |
| * beacon received, SW merge happend but HW TSF not yet updated. | |
| * not possible to reconfigure timers yet, but next time we | |
| * receive a beacon with the same BSSID, the hardware will | |
| * automatically update the TSF and then we need to reconfigure | |
| * the timers. | |
| */ | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, | |
| "need to wait for HW TSF sync\n"); | |
| return; | |
| } else { | |
| /* | |
| * most important case for beacon synchronization between STA. | |
| * | |
| * beacon received and HW TSF has been already updated by HW. | |
| * update next TBTT based on the TSF of the beacon, but make | |
| * sure it is ahead of our local TSF timer. | |
| */ | |
| nexttbtt = bc_tu + roundup(hw_tu + FUDGE - bc_tu, intval); | |
| } | |
| #undef FUDGE | |
| sc->nexttbtt = nexttbtt; | |
| intval |= AR5K_BEACON_ENA; | |
| ath5k_hw_init_beacon(ah, nexttbtt, intval); | |
| /* | |
| * debugging output last in order to preserve the time critical aspect | |
| * of this function | |
| */ | |
| if (bc_tsf == -1) | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, | |
| "reconfigured timers based on HW TSF\n"); | |
| else if (bc_tsf == 0) | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, | |
| "reset HW TSF and timers\n"); | |
| else | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, | |
| "updated timers based on beacon TSF\n"); | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, | |
| "bc_tsf %llx hw_tsf %llx bc_tu %u hw_tu %u nexttbtt %u\n", | |
| (unsigned long long) bc_tsf, | |
| (unsigned long long) hw_tsf, bc_tu, hw_tu, nexttbtt); | |
| ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "intval %u %s %s\n", | |
| intval & AR5K_BEACON_PERIOD, | |
| intval & AR5K_BEACON_ENA ? "AR5K_BEACON_ENA" : "", | |
| intval & AR5K_BEACON_RESET_TSF ? "AR5K_BEACON_RESET_TSF" : ""); | |
| } | |
| /** | |
| * ath5k_beacon_config - Configure the beacon queues and interrupts | |
| * | |
| * @sc: struct ath5k_softc pointer we are operating on | |
| * | |
| * When operating in station mode we want to receive a BMISS interrupt when we | |
| * stop seeing beacons from the AP we've associated with so we can look for | |
| * another AP to associate with. | |
| * | |
| * In IBSS mode we use a self-linked tx descriptor if possible. We enable SWBA | |
| * interrupts to detect TSF updates only. | |
| */ | |
| static void | |
| ath5k_beacon_config(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| ath5k_hw_set_imr(ah, 0); | |
| sc->bmisscount = 0; | |
| sc->imask &= ~(AR5K_INT_BMISS | AR5K_INT_SWBA); | |
| if (sc->opmode == NL80211_IFTYPE_STATION) { | |
| sc->imask |= AR5K_INT_BMISS; | |
| } else if (sc->opmode == NL80211_IFTYPE_ADHOC || | |
| sc->opmode == NL80211_IFTYPE_MESH_POINT || | |
| sc->opmode == NL80211_IFTYPE_AP) { | |
| /* | |
| * In IBSS mode we use a self-linked tx descriptor and let the | |
| * hardware send the beacons automatically. We have to load it | |
| * only once here. | |
| * We use the SWBA interrupt only to keep track of the beacon | |
| * timers in order to detect automatic TSF updates. | |
| */ | |
| ath5k_beaconq_config(sc); | |
| sc->imask |= AR5K_INT_SWBA; | |
| if (sc->opmode == NL80211_IFTYPE_ADHOC) { | |
| if (ath5k_hw_hasveol(ah)) { | |
| spin_lock(&sc->block); | |
| ath5k_beacon_send(sc); | |
| spin_unlock(&sc->block); | |
| } | |
| } else | |
| ath5k_beacon_update_timers(sc, -1); | |
| } | |
| ath5k_hw_set_imr(ah, sc->imask); | |
| } | |
| /********************\ | |
| * Interrupt handling * | |
| \********************/ | |
| static int | |
| ath5k_init(struct ath5k_softc *sc, bool is_resume) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| int ret, i; | |
| mutex_lock(&sc->lock); | |
| if (is_resume && !test_bit(ATH_STAT_STARTED, sc->status)) | |
| goto out_ok; | |
| __clear_bit(ATH_STAT_STARTED, sc->status); | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "mode %d\n", sc->opmode); | |
| /* | |
| * Stop anything previously setup. This is safe | |
| * no matter this is the first time through or not. | |
| */ | |
| ath5k_stop_locked(sc); | |
| /* | |
| * The basic interface to setting the hardware in a good | |
| * state is ``reset''. On return the hardware is known to | |
| * be powered up and with interrupts disabled. This must | |
| * be followed by initialization of the appropriate bits | |
| * and then setup of the interrupt mask. | |
| */ | |
| sc->curchan = sc->hw->conf.channel; | |
| sc->curband = &sc->sbands[sc->curchan->band]; | |
| sc->imask = AR5K_INT_RXOK | AR5K_INT_RXERR | AR5K_INT_RXEOL | | |
| AR5K_INT_RXORN | AR5K_INT_TXDESC | AR5K_INT_TXEOL | | |
| AR5K_INT_FATAL | AR5K_INT_GLOBAL | AR5K_INT_MIB; | |
| ret = ath5k_reset(sc, false, false); | |
| if (ret) | |
| goto done; | |
| /* | |
| * Reset the key cache since some parts do not reset the | |
| * contents on initial power up or resume from suspend. | |
| */ | |
| for (i = 0; i < AR5K_KEYTABLE_SIZE; i++) | |
| ath5k_hw_reset_key(ah, i); | |
| __set_bit(ATH_STAT_STARTED, sc->status); | |
| /* Set ack to be sent at low bit-rates */ | |
| ath5k_hw_set_ack_bitrate_high(ah, false); | |
| mod_timer(&sc->calib_tim, round_jiffies(jiffies + | |
| msecs_to_jiffies(ath5k_calinterval * 1000))); | |
| out_ok: | |
| ret = 0; | |
| done: | |
| mmiowb(); | |
| mutex_unlock(&sc->lock); | |
| return ret; | |
| } | |
| static int | |
| ath5k_stop_locked(struct ath5k_softc *sc) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "invalid %u\n", | |
| test_bit(ATH_STAT_INVALID, sc->status)); | |
| /* | |
| * Shutdown the hardware and driver: | |
| * stop output from above | |
| * disable interrupts | |
| * turn off timers | |
| * turn off the radio | |
| * clear transmit machinery | |
| * clear receive machinery | |
| * drain and release tx queues | |
| * reclaim beacon resources | |
| * power down hardware | |
| * | |
| * Note that some of this work is not possible if the | |
| * hardware is gone (invalid). | |
| */ | |
| ieee80211_stop_queues(sc->hw); | |
| if (!test_bit(ATH_STAT_INVALID, sc->status)) { | |
| ath5k_led_off(sc); | |
| ath5k_hw_set_imr(ah, 0); | |
| synchronize_irq(sc->pdev->irq); | |
| } | |
| ath5k_txq_cleanup(sc); | |
| if (!test_bit(ATH_STAT_INVALID, sc->status)) { | |
| ath5k_rx_stop(sc); | |
| ath5k_hw_phy_disable(ah); | |
| } else | |
| sc->rxlink = NULL; | |
| return 0; | |
| } | |
| /* | |
| * Stop the device, grabbing the top-level lock to protect | |
| * against concurrent entry through ath5k_init (which can happen | |
| * if another thread does a system call and the thread doing the | |
| * stop is preempted). | |
| */ | |
| static int | |
| ath5k_stop_hw(struct ath5k_softc *sc, bool is_suspend) | |
| { | |
| int ret; | |
| mutex_lock(&sc->lock); | |
| ret = ath5k_stop_locked(sc); | |
| if (ret == 0 && !test_bit(ATH_STAT_INVALID, sc->status)) { | |
| /* | |
| * Set the chip in full sleep mode. Note that we are | |
| * careful to do this only when bringing the interface | |
| * completely to a stop. When the chip is in this state | |
| * it must be carefully woken up or references to | |
| * registers in the PCI clock domain may freeze the bus | |
| * (and system). This varies by chip and is mostly an | |
| * issue with newer parts that go to sleep more quickly. | |
| */ | |
| if (sc->ah->ah_mac_srev >= 0x78) { | |
| /* | |
| * XXX | |
| * don't put newer MAC revisions > 7.8 to sleep because | |
| * of the above mentioned problems | |
| */ | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "mac version > 7.8, " | |
| "not putting device to sleep\n"); | |
| } else { | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, | |
| "putting device to full sleep\n"); | |
| ath5k_hw_set_power(sc->ah, AR5K_PM_FULL_SLEEP, true, 0); | |
| } | |
| } | |
| ath5k_txbuf_free(sc, sc->bbuf); | |
| if (!is_suspend) | |
| __clear_bit(ATH_STAT_STARTED, sc->status); | |
| mmiowb(); | |
| mutex_unlock(&sc->lock); | |
| del_timer_sync(&sc->calib_tim); | |
| tasklet_kill(&sc->rxtq); | |
| tasklet_kill(&sc->txtq); | |
| tasklet_kill(&sc->restq); | |
| return ret; | |
| } | |
| static irqreturn_t | |
| ath5k_intr(int irq, void *dev_id) | |
| { | |
| struct ath5k_softc *sc = dev_id; | |
| struct ath5k_hw *ah = sc->ah; | |
| enum ath5k_int status; | |
| unsigned int counter = 1000; | |
| if (unlikely(test_bit(ATH_STAT_INVALID, sc->status) || | |
| !ath5k_hw_is_intr_pending(ah))) | |
| return IRQ_NONE; | |
| do { | |
| /* | |
| * Figure out the reason(s) for the interrupt. Note | |
| * that get_isr returns a pseudo-ISR that may include | |
| * bits we haven't explicitly enabled so we mask the | |
| * value to insure we only process bits we requested. | |
| */ | |
| ath5k_hw_get_isr(ah, &status); /* NB: clears IRQ too */ | |
| ATH5K_DBG(sc, ATH5K_DEBUG_INTR, "status 0x%x/0x%x\n", | |
| status, sc->imask); | |
| status &= sc->imask; /* discard unasked for bits */ | |
| if (unlikely(status & AR5K_INT_FATAL)) { | |
| /* | |
| * Fatal errors are unrecoverable. | |
| * Typically these are caused by DMA errors. | |
| */ | |
| tasklet_schedule(&sc->restq); | |
| } else if (unlikely(status & AR5K_INT_RXORN)) { | |
| tasklet_schedule(&sc->restq); | |
| } else { | |
| if (status & AR5K_INT_SWBA) { | |
| /* | |
| * Software beacon alert--time to send a beacon. | |
| * Handle beacon transmission directly; deferring | |
| * this is too slow to meet timing constraints | |
| * under load. | |
| * | |
| * In IBSS mode we use this interrupt just to | |
| * keep track of the next TBTT (target beacon | |
| * transmission time) in order to detect wether | |
| * automatic TSF updates happened. | |
| */ | |
| if (sc->opmode == NL80211_IFTYPE_ADHOC) { | |
| /* XXX: only if VEOL suppported */ | |
| u64 tsf = ath5k_hw_get_tsf64(ah); | |
| sc->nexttbtt += sc->bintval; | |
| ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, | |
| "SWBA nexttbtt: %x hw_tu: %x " | |
| "TSF: %llx\n", | |
| sc->nexttbtt, | |
| TSF_TO_TU(tsf), | |
| (unsigned long long) tsf); | |
| } else { | |
| spin_lock(&sc->block); | |
| ath5k_beacon_send(sc); | |
| spin_unlock(&sc->block); | |
| } | |
| } | |
| if (status & AR5K_INT_RXEOL) { | |
| /* | |
| * NB: the hardware should re-read the link when | |
| * RXE bit is written, but it doesn't work at | |
| * least on older hardware revs. | |
| */ | |
| sc->rxlink = NULL; | |
| } | |
| if (status & AR5K_INT_TXURN) { | |
| /* bump tx trigger level */ | |
| ath5k_hw_update_tx_triglevel(ah, true); | |
| } | |
| if (status & (AR5K_INT_RXOK | AR5K_INT_RXERR)) | |
| tasklet_schedule(&sc->rxtq); | |
| if (status & (AR5K_INT_TXOK | AR5K_INT_TXDESC | |
| | AR5K_INT_TXERR | AR5K_INT_TXEOL)) | |
| tasklet_schedule(&sc->txtq); | |
| if (status & AR5K_INT_BMISS) { | |
| } | |
| if (status & AR5K_INT_MIB) { | |
| /* | |
| * These stats are also used for ANI i think | |
| * so how about updating them more often ? | |
| */ | |
| ath5k_hw_update_mib_counters(ah, &sc->ll_stats); | |
| } | |
| } | |
| } while (ath5k_hw_is_intr_pending(ah) && counter-- > 0); | |
| if (unlikely(!counter)) | |
| ATH5K_WARN(sc, "too many interrupts, giving up for now\n"); | |
| return IRQ_HANDLED; | |
| } | |
| static void | |
| ath5k_tasklet_reset(unsigned long data) | |
| { | |
| struct ath5k_softc *sc = (void *)data; | |
| ath5k_reset_wake(sc); | |
| } | |
| /* | |
| * Periodically recalibrate the PHY to account | |
| * for temperature/environment changes. | |
| */ | |
| static void | |
| ath5k_calibrate(unsigned long data) | |
| { | |
| struct ath5k_softc *sc = (void *)data; | |
| struct ath5k_hw *ah = sc->ah; | |
| ATH5K_DBG(sc, ATH5K_DEBUG_CALIBRATE, "channel %u/%x\n", | |
| ieee80211_frequency_to_channel(sc->curchan->center_freq), | |
| sc->curchan->hw_value); | |
| if (ath5k_hw_get_rf_gain(ah) == AR5K_RFGAIN_NEED_CHANGE) { | |
| /* | |
| * Rfgain is out of bounds, reset the chip | |
| * to load new gain values. | |
| */ | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "calibration, resetting\n"); | |
| ath5k_reset_wake(sc); | |
| } | |
| if (ath5k_hw_phy_calibrate(ah, sc->curchan)) | |
| ATH5K_ERR(sc, "calibration of channel %u failed\n", | |
| ieee80211_frequency_to_channel( | |
| sc->curchan->center_freq)); | |
| mod_timer(&sc->calib_tim, round_jiffies(jiffies + | |
| msecs_to_jiffies(ath5k_calinterval * 1000))); | |
| } | |
| /***************\ | |
| * LED functions * | |
| \***************/ | |
| static void | |
| ath5k_led_enable(struct ath5k_softc *sc) | |
| { | |
| if (test_bit(ATH_STAT_LEDSOFT, sc->status)) { | |
| ath5k_hw_set_gpio_output(sc->ah, sc->led_pin); | |
| ath5k_led_off(sc); | |
| } | |
| } | |
| static void | |
| ath5k_led_on(struct ath5k_softc *sc) | |
| { | |
| if (!test_bit(ATH_STAT_LEDSOFT, sc->status)) | |
| return; | |
| ath5k_hw_set_gpio(sc->ah, sc->led_pin, sc->led_on); | |
| } | |
| static void | |
| ath5k_led_off(struct ath5k_softc *sc) | |
| { | |
| if (!test_bit(ATH_STAT_LEDSOFT, sc->status)) | |
| return; | |
| ath5k_hw_set_gpio(sc->ah, sc->led_pin, !sc->led_on); | |
| } | |
| static void | |
| ath5k_led_brightness_set(struct led_classdev *led_dev, | |
| enum led_brightness brightness) | |
| { | |
| struct ath5k_led *led = container_of(led_dev, struct ath5k_led, | |
| led_dev); | |
| if (brightness == LED_OFF) | |
| ath5k_led_off(led->sc); | |
| else | |
| ath5k_led_on(led->sc); | |
| } | |
| static int | |
| ath5k_register_led(struct ath5k_softc *sc, struct ath5k_led *led, | |
| const char *name, char *trigger) | |
| { | |
| int err; | |
| led->sc = sc; | |
| strncpy(led->name, name, sizeof(led->name)); | |
| led->led_dev.name = led->name; | |
| led->led_dev.default_trigger = trigger; | |
| led->led_dev.brightness_set = ath5k_led_brightness_set; | |
| err = led_classdev_register(&sc->pdev->dev, &led->led_dev); | |
| if (err) { | |
| ATH5K_WARN(sc, "could not register LED %s\n", name); | |
| led->sc = NULL; | |
| } | |
| return err; | |
| } | |
| static void | |
| ath5k_unregister_led(struct ath5k_led *led) | |
| { | |
| if (!led->sc) | |
| return; | |
| led_classdev_unregister(&led->led_dev); | |
| ath5k_led_off(led->sc); | |
| led->sc = NULL; | |
| } | |
| static void | |
| ath5k_unregister_leds(struct ath5k_softc *sc) | |
| { | |
| ath5k_unregister_led(&sc->rx_led); | |
| ath5k_unregister_led(&sc->tx_led); | |
| } | |
| static int | |
| ath5k_init_leds(struct ath5k_softc *sc) | |
| { | |
| int ret = 0; | |
| struct ieee80211_hw *hw = sc->hw; | |
| struct pci_dev *pdev = sc->pdev; | |
| char name[ATH5K_LED_MAX_NAME_LEN + 1]; | |
| /* | |
| * Auto-enable soft led processing for IBM cards and for | |
| * 5211 minipci cards. | |
| */ | |
| if (pdev->device == PCI_DEVICE_ID_ATHEROS_AR5212_IBM || | |
| pdev->device == PCI_DEVICE_ID_ATHEROS_AR5211) { | |
| __set_bit(ATH_STAT_LEDSOFT, sc->status); | |
| sc->led_pin = 0; | |
| sc->led_on = 0; /* active low */ | |
| } | |
| /* Enable softled on PIN1 on HP Compaq nc6xx, nc4000 & nx5000 laptops */ | |
| if (pdev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ) { | |
| __set_bit(ATH_STAT_LEDSOFT, sc->status); | |
| sc->led_pin = 1; | |
| sc->led_on = 1; /* active high */ | |
| } | |
| if (!test_bit(ATH_STAT_LEDSOFT, sc->status)) | |
| goto out; | |
| ath5k_led_enable(sc); | |
| snprintf(name, sizeof(name), "ath5k-%s::rx", wiphy_name(hw->wiphy)); | |
| ret = ath5k_register_led(sc, &sc->rx_led, name, | |
| ieee80211_get_rx_led_name(hw)); | |
| if (ret) | |
| goto out; | |
| snprintf(name, sizeof(name), "ath5k-%s::tx", wiphy_name(hw->wiphy)); | |
| ret = ath5k_register_led(sc, &sc->tx_led, name, | |
| ieee80211_get_tx_led_name(hw)); | |
| out: | |
| return ret; | |
| } | |
| /********************\ | |
| * Mac80211 functions * | |
| \********************/ | |
| static int | |
| ath5k_tx(struct ieee80211_hw *hw, struct sk_buff *skb) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| struct ath5k_buf *bf; | |
| unsigned long flags; | |
| int hdrlen; | |
| int padsize; | |
| ath5k_debug_dump_skb(sc, skb, "TX ", 1); | |
| if (sc->opmode == NL80211_IFTYPE_MONITOR) | |
| ATH5K_DBG(sc, ATH5K_DEBUG_XMIT, "tx in monitor (scan?)\n"); | |
| /* | |
| * the hardware expects the header padded to 4 byte boundaries | |
| * if this is not the case we add the padding after the header | |
| */ | |
| hdrlen = ieee80211_get_hdrlen_from_skb(skb); | |
| padsize = ath5k_pad_size(hdrlen); | |
| if (padsize) { | |
| if (skb_headroom(skb) < padsize) { | |
| ATH5K_ERR(sc, "tx hdrlen not %%4: %d not enough" | |
| " headroom to pad %d\n", hdrlen, padsize); | |
| return NETDEV_TX_BUSY; | |
| } | |
| skb_push(skb, padsize); | |
| memmove(skb->data, skb->data+padsize, hdrlen); | |
| } | |
| spin_lock_irqsave(&sc->txbuflock, flags); | |
| if (list_empty(&sc->txbuf)) { | |
| ATH5K_ERR(sc, "no further txbuf available, dropping packet\n"); | |
| spin_unlock_irqrestore(&sc->txbuflock, flags); | |
| ieee80211_stop_queue(hw, skb_get_queue_mapping(skb)); | |
| return NETDEV_TX_BUSY; | |
| } | |
| bf = list_first_entry(&sc->txbuf, struct ath5k_buf, list); | |
| list_del(&bf->list); | |
| sc->txbuf_len--; | |
| if (list_empty(&sc->txbuf)) | |
| ieee80211_stop_queues(hw); | |
| spin_unlock_irqrestore(&sc->txbuflock, flags); | |
| bf->skb = skb; | |
| if (ath5k_txbuf_setup(sc, bf)) { | |
| bf->skb = NULL; | |
| spin_lock_irqsave(&sc->txbuflock, flags); | |
| list_add_tail(&bf->list, &sc->txbuf); | |
| sc->txbuf_len++; | |
| spin_unlock_irqrestore(&sc->txbuflock, flags); | |
| dev_kfree_skb_any(skb); | |
| return NETDEV_TX_OK; | |
| } | |
| return NETDEV_TX_OK; | |
| } | |
| static int | |
| ath5k_reset(struct ath5k_softc *sc, bool stop, bool change_channel) | |
| { | |
| struct ath5k_hw *ah = sc->ah; | |
| int ret; | |
| ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "resetting\n"); | |
| if (stop) { | |
| ath5k_hw_set_imr(ah, 0); | |
| ath5k_txq_cleanup(sc); | |
| ath5k_rx_stop(sc); | |
| } | |
| ret = ath5k_hw_reset(ah, sc->opmode, sc->curchan, true); | |
| if (ret) { | |
| ATH5K_ERR(sc, "can't reset hardware (%d)\n", ret); | |
| goto err; | |
| } | |
| /* | |
| * This is needed only to setup initial state | |
| * but it's best done after a reset. | |
| */ | |
| ath5k_hw_set_txpower_limit(sc->ah, 0); | |
| ret = ath5k_rx_start(sc); | |
| if (ret) { | |
| ATH5K_ERR(sc, "can't start recv logic\n"); | |
| goto err; | |
| } | |
| /* | |
| * Change channels and update the h/w rate map if we're switching; | |
| * e.g. 11a to 11b/g. | |
| * | |
| * We may be doing a reset in response to an ioctl that changes the | |
| * channel so update any state that might change as a result. | |
| * | |
| * XXX needed? | |
| */ | |
| /* ath5k_chan_change(sc, c); */ | |
| ath5k_beacon_config(sc); | |
| /* intrs are enabled by ath5k_beacon_config */ | |
| return 0; | |
| err: | |
| return ret; | |
| } | |
| static int | |
| ath5k_reset_wake(struct ath5k_softc *sc) | |
| { | |
| int ret; | |
| ret = ath5k_reset(sc, true, true); | |
| if (!ret) | |
| ieee80211_wake_queues(sc->hw); | |
| return ret; | |
| } | |
| static int ath5k_start(struct ieee80211_hw *hw) | |
| { | |
| return ath5k_init(hw->priv, false); | |
| } | |
| static void ath5k_stop(struct ieee80211_hw *hw) | |
| { | |
| ath5k_stop_hw(hw->priv, false); | |
| } | |
| static int ath5k_add_interface(struct ieee80211_hw *hw, | |
| struct ieee80211_if_init_conf *conf) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| int ret; | |
| mutex_lock(&sc->lock); | |
| if (sc->vif) { | |
| ret = 0; | |
| goto end; | |
| } | |
| sc->vif = conf->vif; | |
| switch (conf->type) { | |
| case NL80211_IFTYPE_AP: | |
| case NL80211_IFTYPE_STATION: | |
| case NL80211_IFTYPE_ADHOC: | |
| case NL80211_IFTYPE_MESH_POINT: | |
| case NL80211_IFTYPE_MONITOR: | |
| sc->opmode = conf->type; | |
| break; | |
| default: | |
| ret = -EOPNOTSUPP; | |
| goto end; | |
| } | |
| /* Set to a reasonable value. Note that this will | |
| * be set to mac80211's value at ath5k_config(). */ | |
| sc->bintval = 1000; | |
| ath5k_hw_set_lladdr(sc->ah, conf->mac_addr); | |
| ret = 0; | |
| end: | |
| mutex_unlock(&sc->lock); | |
| return ret; | |
| } | |
| static void | |
| ath5k_remove_interface(struct ieee80211_hw *hw, | |
| struct ieee80211_if_init_conf *conf) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| u8 mac[ETH_ALEN] = {}; | |
| mutex_lock(&sc->lock); | |
| if (sc->vif != conf->vif) | |
| goto end; | |
| ath5k_hw_set_lladdr(sc->ah, mac); | |
| sc->vif = NULL; | |
| end: | |
| mutex_unlock(&sc->lock); | |
| } | |
| /* | |
| * TODO: Phy disable/diversity etc | |
| */ | |
| static int | |
| ath5k_config(struct ieee80211_hw *hw, u32 changed) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| struct ieee80211_conf *conf = &hw->conf; | |
| int ret; | |
| mutex_lock(&sc->lock); | |
| sc->bintval = conf->beacon_int; | |
| sc->power_level = conf->power_level; | |
| ret = ath5k_chan_set(sc, conf->channel); | |
| mutex_unlock(&sc->lock); | |
| return ret; | |
| } | |
| static int | |
| ath5k_config_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif, | |
| struct ieee80211_if_conf *conf) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| struct ath5k_hw *ah = sc->ah; | |
| int ret; | |
| mutex_lock(&sc->lock); | |
| if (sc->vif != vif) { | |
| ret = -EIO; | |
| goto unlock; | |
| } | |
| if (conf->changed & IEEE80211_IFCC_BSSID && conf->bssid) { | |
| /* Cache for later use during resets */ | |
| memcpy(ah->ah_bssid, conf->bssid, ETH_ALEN); | |
| /* XXX: assoc id is set to 0 for now, mac80211 doesn't have | |
| * a clean way of letting us retrieve this yet. */ | |
| ath5k_hw_set_associd(ah, ah->ah_bssid, 0); | |
| mmiowb(); | |
| } | |
| if (conf->changed & IEEE80211_IFCC_BEACON && | |
| (vif->type == NL80211_IFTYPE_ADHOC || | |
| vif->type == NL80211_IFTYPE_MESH_POINT || | |
| vif->type == NL80211_IFTYPE_AP)) { | |
| struct sk_buff *beacon = ieee80211_beacon_get(hw, vif); | |
| if (!beacon) { | |
| ret = -ENOMEM; | |
| goto unlock; | |
| } | |
| ath5k_beacon_update(sc, beacon); | |
| } | |
| mutex_unlock(&sc->lock); | |
| return ath5k_reset_wake(sc); | |
| unlock: | |
| mutex_unlock(&sc->lock); | |
| return ret; | |
| } | |
| #define SUPPORTED_FIF_FLAGS \ | |
| FIF_PROMISC_IN_BSS | FIF_ALLMULTI | FIF_FCSFAIL | \ | |
| FIF_PLCPFAIL | FIF_CONTROL | FIF_OTHER_BSS | \ | |
| FIF_BCN_PRBRESP_PROMISC | |
| /* | |
| * o always accept unicast, broadcast, and multicast traffic | |
| * o multicast traffic for all BSSIDs will be enabled if mac80211 | |
| * says it should be | |
| * o maintain current state of phy ofdm or phy cck error reception. | |
| * If the hardware detects any of these type of errors then | |
| * ath5k_hw_get_rx_filter() will pass to us the respective | |
| * hardware filters to be able to receive these type of frames. | |
| * o probe request frames are accepted only when operating in | |
| * hostap, adhoc, or monitor modes | |
| * o enable promiscuous mode according to the interface state | |
| * o accept beacons: | |
| * - when operating in adhoc mode so the 802.11 layer creates | |
| * node table entries for peers, | |
| * - when operating in station mode for collecting rssi data when | |
| * the station is otherwise quiet, or | |
| * - when scanning | |
| */ | |
| static void ath5k_configure_filter(struct ieee80211_hw *hw, | |
| unsigned int changed_flags, | |
| unsigned int *new_flags, | |
| int mc_count, struct dev_mc_list *mclist) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| struct ath5k_hw *ah = sc->ah; | |
| u32 mfilt[2], val, rfilt; | |
| u8 pos; | |
| int i; | |
| mfilt[0] = 0; | |
| mfilt[1] = 0; | |
| /* Only deal with supported flags */ | |
| changed_flags &= SUPPORTED_FIF_FLAGS; | |
| *new_flags &= SUPPORTED_FIF_FLAGS; | |
| /* If HW detects any phy or radar errors, leave those filters on. | |
| * Also, always enable Unicast, Broadcasts and Multicast | |
| * XXX: move unicast, bssid broadcasts and multicast to mac80211 */ | |
| rfilt = (ath5k_hw_get_rx_filter(ah) & (AR5K_RX_FILTER_PHYERR)) | | |
| (AR5K_RX_FILTER_UCAST | AR5K_RX_FILTER_BCAST | | |
| AR5K_RX_FILTER_MCAST); | |
| if (changed_flags & (FIF_PROMISC_IN_BSS | FIF_OTHER_BSS)) { | |
| if (*new_flags & FIF_PROMISC_IN_BSS) { | |
| rfilt |= AR5K_RX_FILTER_PROM; | |
| __set_bit(ATH_STAT_PROMISC, sc->status); | |
| } else { | |
| __clear_bit(ATH_STAT_PROMISC, sc->status); | |
| } | |
| } | |
| /* Note, AR5K_RX_FILTER_MCAST is already enabled */ | |
| if (*new_flags & FIF_ALLMULTI) { | |
| mfilt[0] = ~0; | |
| mfilt[1] = ~0; | |
| } else { | |
| for (i = 0; i < mc_count; i++) { | |
| if (!mclist) | |
| break; | |
| /* calculate XOR of eight 6-bit values */ | |
| val = get_unaligned_le32(mclist->dmi_addr + 0); | |
| pos = (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val; | |
| val = get_unaligned_le32(mclist->dmi_addr + 3); | |
| pos ^= (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val; | |
| pos &= 0x3f; | |
| mfilt[pos / 32] |= (1 << (pos % 32)); | |
| /* XXX: we might be able to just do this instead, | |
| * but not sure, needs testing, if we do use this we'd | |
| * neet to inform below to not reset the mcast */ | |
| /* ath5k_hw_set_mcast_filterindex(ah, | |
| * mclist->dmi_addr[5]); */ | |
| mclist = mclist->next; | |
| } | |
| } | |
| /* This is the best we can do */ | |
| if (*new_flags & (FIF_FCSFAIL | FIF_PLCPFAIL)) | |
| rfilt |= AR5K_RX_FILTER_PHYERR; | |
| /* FIF_BCN_PRBRESP_PROMISC really means to enable beacons | |
| * and probes for any BSSID, this needs testing */ | |
| if (*new_flags & FIF_BCN_PRBRESP_PROMISC) | |
| rfilt |= AR5K_RX_FILTER_BEACON | AR5K_RX_FILTER_PROBEREQ; | |
| /* FIF_CONTROL doc says that if FIF_PROMISC_IN_BSS is not | |
| * set we should only pass on control frames for this | |
| * station. This needs testing. I believe right now this | |
| * enables *all* control frames, which is OK.. but | |
| * but we should see if we can improve on granularity */ | |
| if (*new_flags & FIF_CONTROL) | |
| rfilt |= AR5K_RX_FILTER_CONTROL; | |
| /* Additional settings per mode -- this is per ath5k */ | |
| /* XXX move these to mac80211, and add a beacon IFF flag to mac80211 */ | |
| if (sc->opmode == NL80211_IFTYPE_MONITOR) | |
| rfilt |= AR5K_RX_FILTER_CONTROL | AR5K_RX_FILTER_BEACON | | |
| AR5K_RX_FILTER_PROBEREQ | AR5K_RX_FILTER_PROM; | |
| if (sc->opmode != NL80211_IFTYPE_STATION) | |
| rfilt |= AR5K_RX_FILTER_PROBEREQ; | |
| if (sc->opmode != NL80211_IFTYPE_AP && | |
| sc->opmode != NL80211_IFTYPE_MESH_POINT && | |
| test_bit(ATH_STAT_PROMISC, sc->status)) | |
| rfilt |= AR5K_RX_FILTER_PROM; | |
| if ((sc->opmode == NL80211_IFTYPE_STATION && sc->assoc) || | |
| sc->opmode == NL80211_IFTYPE_ADHOC || | |
| sc->opmode == NL80211_IFTYPE_AP) | |
| rfilt |= AR5K_RX_FILTER_BEACON; | |
| if (sc->opmode == NL80211_IFTYPE_MESH_POINT) | |
| rfilt |= AR5K_RX_FILTER_CONTROL | AR5K_RX_FILTER_BEACON | | |
| AR5K_RX_FILTER_PROBEREQ | AR5K_RX_FILTER_PROM; | |
| /* Set filters */ | |
| ath5k_hw_set_rx_filter(ah, rfilt); | |
| /* Set multicast bits */ | |
| ath5k_hw_set_mcast_filter(ah, mfilt[0], mfilt[1]); | |
| /* Set the cached hw filter flags, this will alter actually | |
| * be set in HW */ | |
| sc->filter_flags = rfilt; | |
| } | |
| static int | |
| ath5k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, | |
| const u8 *local_addr, const u8 *addr, | |
| struct ieee80211_key_conf *key) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| int ret = 0; | |
| if (modparam_nohwcrypt) | |
| return -EOPNOTSUPP; | |
| switch (key->alg) { | |
| case ALG_WEP: | |
| case ALG_TKIP: | |
| break; | |
| case ALG_CCMP: | |
| return -EOPNOTSUPP; | |
| default: | |
| WARN_ON(1); | |
| return -EINVAL; | |
| } | |
| mutex_lock(&sc->lock); | |
| switch (cmd) { | |
| case SET_KEY: | |
| ret = ath5k_hw_set_key(sc->ah, key->keyidx, key, addr); | |
| if (ret) { | |
| ATH5K_ERR(sc, "can't set the key\n"); | |
| goto unlock; | |
| } | |
| __set_bit(key->keyidx, sc->keymap); | |
| key->hw_key_idx = key->keyidx; | |
| key->flags |= (IEEE80211_KEY_FLAG_GENERATE_IV | | |
| IEEE80211_KEY_FLAG_GENERATE_MMIC); | |
| break; | |
| case DISABLE_KEY: | |
| ath5k_hw_reset_key(sc->ah, key->keyidx); | |
| __clear_bit(key->keyidx, sc->keymap); | |
| break; | |
| default: | |
| ret = -EINVAL; | |
| goto unlock; | |
| } | |
| unlock: | |
| mmiowb(); | |
| mutex_unlock(&sc->lock); | |
| return ret; | |
| } | |
| static int | |
| ath5k_get_stats(struct ieee80211_hw *hw, | |
| struct ieee80211_low_level_stats *stats) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| struct ath5k_hw *ah = sc->ah; | |
| /* Force update */ | |
| ath5k_hw_update_mib_counters(ah, &sc->ll_stats); | |
| memcpy(stats, &sc->ll_stats, sizeof(sc->ll_stats)); | |
| return 0; | |
| } | |
| static int | |
| ath5k_get_tx_stats(struct ieee80211_hw *hw, | |
| struct ieee80211_tx_queue_stats *stats) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| memcpy(stats, &sc->tx_stats, sizeof(sc->tx_stats)); | |
| return 0; | |
| } | |
| static u64 | |
| ath5k_get_tsf(struct ieee80211_hw *hw) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| return ath5k_hw_get_tsf64(sc->ah); | |
| } | |
| static void | |
| ath5k_reset_tsf(struct ieee80211_hw *hw) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| /* | |
| * in IBSS mode we need to update the beacon timers too. | |
| * this will also reset the TSF if we call it with 0 | |
| */ | |
| if (sc->opmode == NL80211_IFTYPE_ADHOC) | |
| ath5k_beacon_update_timers(sc, 0); | |
| else | |
| ath5k_hw_reset_tsf(sc->ah); | |
| } | |
| static int | |
| ath5k_beacon_update(struct ath5k_softc *sc, struct sk_buff *skb) | |
| { | |
| unsigned long flags; | |
| int ret; | |
| ath5k_debug_dump_skb(sc, skb, "BC ", 1); | |
| spin_lock_irqsave(&sc->block, flags); | |
| ath5k_txbuf_free(sc, sc->bbuf); | |
| sc->bbuf->skb = skb; | |
| ret = ath5k_beacon_setup(sc, sc->bbuf); | |
| if (ret) | |
| sc->bbuf->skb = NULL; | |
| spin_unlock_irqrestore(&sc->block, flags); | |
| if (!ret) { | |
| ath5k_beacon_config(sc); | |
| mmiowb(); | |
| } | |
| return ret; | |
| } | |
| static void | |
| set_beacon_filter(struct ieee80211_hw *hw, bool enable) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| struct ath5k_hw *ah = sc->ah; | |
| u32 rfilt; | |
| rfilt = ath5k_hw_get_rx_filter(ah); | |
| if (enable) | |
| rfilt |= AR5K_RX_FILTER_BEACON; | |
| else | |
| rfilt &= ~AR5K_RX_FILTER_BEACON; | |
| ath5k_hw_set_rx_filter(ah, rfilt); | |
| sc->filter_flags = rfilt; | |
| } | |
| static void ath5k_bss_info_changed(struct ieee80211_hw *hw, | |
| struct ieee80211_vif *vif, | |
| struct ieee80211_bss_conf *bss_conf, | |
| u32 changes) | |
| { | |
| struct ath5k_softc *sc = hw->priv; | |
| if (changes & BSS_CHANGED_ASSOC) { | |
| mutex_lock(&sc->lock); | |
| sc->assoc = bss_conf->assoc; | |
| if (sc->opmode == NL80211_IFTYPE_STATION) | |
| set_beacon_filter(hw, sc->assoc); | |
| mutex_unlock(&sc->lock); | |
| } | |
| } |