| /****************************************************************************/ |
| |
| /* |
| * mcfuart.h -- ColdFire internal UART support defines. |
| * |
| * (C) Copyright 1999-2003, Greg Ungerer (gerg@snapgear.com) |
| * (C) Copyright 2000, Lineo Inc. (www.lineo.com) |
| */ |
| |
| /****************************************************************************/ |
| #ifndef mcfuart_h |
| #define mcfuart_h |
| /****************************************************************************/ |
| |
| #include <linux/serial_core.h> |
| #include <linux/platform_device.h> |
| |
| struct mcf_platform_uart { |
| unsigned long mapbase; /* Physical address base */ |
| void __iomem *membase; /* Virtual address if mapped */ |
| unsigned int irq; /* Interrupt vector */ |
| unsigned int uartclk; /* UART clock rate */ |
| }; |
| |
| /* |
| * Define the ColdFire UART register set addresses. |
| */ |
| #define MCFUART_UMR 0x00 /* Mode register (r/w) */ |
| #define MCFUART_USR 0x04 /* Status register (r) */ |
| #define MCFUART_UCSR 0x04 /* Clock Select (w) */ |
| #define MCFUART_UCR 0x08 /* Command register (w) */ |
| #define MCFUART_URB 0x0c /* Receiver Buffer (r) */ |
| #define MCFUART_UTB 0x0c /* Transmit Buffer (w) */ |
| #define MCFUART_UIPCR 0x10 /* Input Port Change (r) */ |
| #define MCFUART_UACR 0x10 /* Auxiliary Control (w) */ |
| #define MCFUART_UISR 0x14 /* Interrupt Status (r) */ |
| #define MCFUART_UIMR 0x14 /* Interrupt Mask (w) */ |
| #define MCFUART_UBG1 0x18 /* Baud Rate MSB (r/w) */ |
| #define MCFUART_UBG2 0x1c /* Baud Rate LSB (r/w) */ |
| #ifdef CONFIG_M5272 |
| #define MCFUART_UTF 0x28 /* Transmitter FIFO (r/w) */ |
| #define MCFUART_URF 0x2c /* Receiver FIFO (r/w) */ |
| #define MCFUART_UFPD 0x30 /* Frac Prec. Divider (r/w) */ |
| #else |
| #define MCFUART_UIVR 0x30 /* Interrupt Vector (r/w) */ |
| #endif |
| #define MCFUART_UIPR 0x34 /* Input Port (r) */ |
| #define MCFUART_UOP1 0x38 /* Output Port Bit Set (w) */ |
| #define MCFUART_UOP0 0x3c /* Output Port Bit Reset (w) */ |
| |
| |
| /* |
| * Define bit flags in Mode Register 1 (MR1). |
| */ |
| #define MCFUART_MR1_RXRTS 0x80 /* Auto RTS flow control */ |
| #define MCFUART_MR1_RXIRQFULL 0x40 /* RX IRQ type FULL */ |
| #define MCFUART_MR1_RXIRQRDY 0x00 /* RX IRQ type RDY */ |
| #define MCFUART_MR1_RXERRBLOCK 0x20 /* RX block error mode */ |
| #define MCFUART_MR1_RXERRCHAR 0x00 /* RX char error mode */ |
| |
| #define MCFUART_MR1_PARITYNONE 0x10 /* No parity */ |
| #define MCFUART_MR1_PARITYEVEN 0x00 /* Even parity */ |
| #define MCFUART_MR1_PARITYODD 0x04 /* Odd parity */ |
| #define MCFUART_MR1_PARITYSPACE 0x08 /* Space parity */ |
| #define MCFUART_MR1_PARITYMARK 0x0c /* Mark parity */ |
| |
| #define MCFUART_MR1_CS5 0x00 /* 5 bits per char */ |
| #define MCFUART_MR1_CS6 0x01 /* 6 bits per char */ |
| #define MCFUART_MR1_CS7 0x02 /* 7 bits per char */ |
| #define MCFUART_MR1_CS8 0x03 /* 8 bits per char */ |
| |
| /* |
| * Define bit flags in Mode Register 2 (MR2). |
| */ |
| #define MCFUART_MR2_LOOPBACK 0x80 /* Loopback mode */ |
| #define MCFUART_MR2_REMOTELOOP 0xc0 /* Remote loopback mode */ |
| #define MCFUART_MR2_AUTOECHO 0x40 /* Automatic echo */ |
| #define MCFUART_MR2_TXRTS 0x20 /* Assert RTS on TX */ |
| #define MCFUART_MR2_TXCTS 0x10 /* Auto CTS flow control */ |
| |
| #define MCFUART_MR2_STOP1 0x07 /* 1 stop bit */ |
| #define MCFUART_MR2_STOP15 0x08 /* 1.5 stop bits */ |
| #define MCFUART_MR2_STOP2 0x0f /* 2 stop bits */ |
| |
| /* |
| * Define bit flags in Status Register (USR). |
| */ |
| #define MCFUART_USR_RXBREAK 0x80 /* Received BREAK */ |
| #define MCFUART_USR_RXFRAMING 0x40 /* Received framing error */ |
| #define MCFUART_USR_RXPARITY 0x20 /* Received parity error */ |
| #define MCFUART_USR_RXOVERRUN 0x10 /* Received overrun error */ |
| #define MCFUART_USR_TXEMPTY 0x08 /* Transmitter empty */ |
| #define MCFUART_USR_TXREADY 0x04 /* Transmitter ready */ |
| #define MCFUART_USR_RXFULL 0x02 /* Receiver full */ |
| #define MCFUART_USR_RXREADY 0x01 /* Receiver ready */ |
| |
| #define MCFUART_USR_RXERR (MCFUART_USR_RXBREAK | MCFUART_USR_RXFRAMING | \ |
| MCFUART_USR_RXPARITY | MCFUART_USR_RXOVERRUN) |
| |
| /* |
| * Define bit flags in Clock Select Register (UCSR). |
| */ |
| #define MCFUART_UCSR_RXCLKTIMER 0xd0 /* RX clock is timer */ |
| #define MCFUART_UCSR_RXCLKEXT16 0xe0 /* RX clock is external x16 */ |
| #define MCFUART_UCSR_RXCLKEXT1 0xf0 /* RX clock is external x1 */ |
| |
| #define MCFUART_UCSR_TXCLKTIMER 0x0d /* TX clock is timer */ |
| #define MCFUART_UCSR_TXCLKEXT16 0x0e /* TX clock is external x16 */ |
| #define MCFUART_UCSR_TXCLKEXT1 0x0f /* TX clock is external x1 */ |
| |
| /* |
| * Define bit flags in Command Register (UCR). |
| */ |
| #define MCFUART_UCR_CMDNULL 0x00 /* No command */ |
| #define MCFUART_UCR_CMDRESETMRPTR 0x10 /* Reset MR pointer */ |
| #define MCFUART_UCR_CMDRESETRX 0x20 /* Reset receiver */ |
| #define MCFUART_UCR_CMDRESETTX 0x30 /* Reset transmitter */ |
| #define MCFUART_UCR_CMDRESETERR 0x40 /* Reset error status */ |
| #define MCFUART_UCR_CMDRESETBREAK 0x50 /* Reset BREAK change */ |
| #define MCFUART_UCR_CMDBREAKSTART 0x60 /* Start BREAK */ |
| #define MCFUART_UCR_CMDBREAKSTOP 0x70 /* Stop BREAK */ |
| |
| #define MCFUART_UCR_TXNULL 0x00 /* No TX command */ |
| #define MCFUART_UCR_TXENABLE 0x04 /* Enable TX */ |
| #define MCFUART_UCR_TXDISABLE 0x08 /* Disable TX */ |
| #define MCFUART_UCR_RXNULL 0x00 /* No RX command */ |
| #define MCFUART_UCR_RXENABLE 0x01 /* Enable RX */ |
| #define MCFUART_UCR_RXDISABLE 0x02 /* Disable RX */ |
| |
| /* |
| * Define bit flags in Input Port Change Register (UIPCR). |
| */ |
| #define MCFUART_UIPCR_CTSCOS 0x10 /* CTS change of state */ |
| #define MCFUART_UIPCR_CTS 0x01 /* CTS value */ |
| |
| /* |
| * Define bit flags in Input Port Register (UIP). |
| */ |
| #define MCFUART_UIPR_CTS 0x01 /* CTS value */ |
| |
| /* |
| * Define bit flags in Output Port Registers (UOP). |
| * Clear bit by writing to UOP0, set by writing to UOP1. |
| */ |
| #define MCFUART_UOP_RTS 0x01 /* RTS set or clear */ |
| |
| /* |
| * Define bit flags in the Auxiliary Control Register (UACR). |
| */ |
| #define MCFUART_UACR_IEC 0x01 /* Input enable control */ |
| |
| /* |
| * Define bit flags in Interrupt Status Register (UISR). |
| * These same bits are used for the Interrupt Mask Register (UIMR). |
| */ |
| #define MCFUART_UIR_COS 0x80 /* Change of state (CTS) */ |
| #define MCFUART_UIR_DELTABREAK 0x04 /* Break start or stop */ |
| #define MCFUART_UIR_RXREADY 0x02 /* Receiver ready */ |
| #define MCFUART_UIR_TXREADY 0x01 /* Transmitter ready */ |
| |
| #ifdef CONFIG_M5272 |
| /* |
| * Define bit flags in the Transmitter FIFO Register (UTF). |
| */ |
| #define MCFUART_UTF_TXB 0x1f /* Transmitter data level */ |
| #define MCFUART_UTF_FULL 0x20 /* Transmitter fifo full */ |
| #define MCFUART_UTF_TXS 0xc0 /* Transmitter status */ |
| |
| /* |
| * Define bit flags in the Receiver FIFO Register (URF). |
| */ |
| #define MCFUART_URF_RXB 0x1f /* Receiver data level */ |
| #define MCFUART_URF_FULL 0x20 /* Receiver fifo full */ |
| #define MCFUART_URF_RXS 0xc0 /* Receiver status */ |
| #endif |
| |
| #if defined(CONFIG_M54xx) |
| #define MCFUART_TXFIFOSIZE 512 |
| #elif defined(CONFIG_M5272) |
| #define MCFUART_TXFIFOSIZE 25 |
| #else |
| #define MCFUART_TXFIFOSIZE 1 |
| #endif |
| /****************************************************************************/ |
| #endif /* mcfuart_h */ |
