| /* | |
| * linux/drivers/char/at91_serial.c | |
| * | |
| * Driver for Atmel AT91RM9200 Serial ports | |
| * Copyright (C) 2003 Rick Bronson | |
| * | |
| * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd. | |
| * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License as published by | |
| * the Free Software Foundation; either version 2 of the License, or | |
| * (at your option) any later version. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program; if not, write to the Free Software | |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA | |
| * | |
| */ | |
| #include <linux/config.h> | |
| #include <linux/module.h> | |
| #include <linux/tty.h> | |
| #include <linux/ioport.h> | |
| #include <linux/slab.h> | |
| #include <linux/init.h> | |
| #include <linux/serial.h> | |
| #include <linux/clk.h> | |
| #include <linux/console.h> | |
| #include <linux/sysrq.h> | |
| #include <linux/tty_flip.h> | |
| #include <linux/platform_device.h> | |
| #include <asm/io.h> | |
| #include <asm/arch/at91rm9200_usart.h> | |
| #include <asm/arch/at91rm9200_pdc.h> | |
| #include <asm/mach/serial_at91.h> | |
| #include <asm/arch/board.h> | |
| #include <asm/arch/system.h> | |
| #if defined(CONFIG_SERIAL_AT91_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) | |
| #define SUPPORT_SYSRQ | |
| #endif | |
| #include <linux/serial_core.h> | |
| #ifdef CONFIG_SERIAL_AT91_TTYAT | |
| /* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we | |
| * should coexist with the 8250 driver, such as if we have an external 16C550 | |
| * UART. */ | |
| #define SERIAL_AT91_MAJOR 204 | |
| #define MINOR_START 154 | |
| #define AT91_DEVICENAME "ttyAT" | |
| #else | |
| /* Use device name ttyS, major 4, minor 64-68. This is the usual serial port | |
| * name, but it is legally reserved for the 8250 driver. */ | |
| #define SERIAL_AT91_MAJOR TTY_MAJOR | |
| #define MINOR_START 64 | |
| #define AT91_DEVICENAME "ttyS" | |
| #endif | |
| #define AT91_ISR_PASS_LIMIT 256 | |
| #define UART_PUT_CR(port,v) writel(v, (port)->membase + AT91_US_CR) | |
| #define UART_GET_MR(port) readl((port)->membase + AT91_US_MR) | |
| #define UART_PUT_MR(port,v) writel(v, (port)->membase + AT91_US_MR) | |
| #define UART_PUT_IER(port,v) writel(v, (port)->membase + AT91_US_IER) | |
| #define UART_PUT_IDR(port,v) writel(v, (port)->membase + AT91_US_IDR) | |
| #define UART_GET_IMR(port) readl((port)->membase + AT91_US_IMR) | |
| #define UART_GET_CSR(port) readl((port)->membase + AT91_US_CSR) | |
| #define UART_GET_CHAR(port) readl((port)->membase + AT91_US_RHR) | |
| #define UART_PUT_CHAR(port,v) writel(v, (port)->membase + AT91_US_THR) | |
| #define UART_GET_BRGR(port) readl((port)->membase + AT91_US_BRGR) | |
| #define UART_PUT_BRGR(port,v) writel(v, (port)->membase + AT91_US_BRGR) | |
| #define UART_PUT_RTOR(port,v) writel(v, (port)->membase + AT91_US_RTOR) | |
| // #define UART_GET_CR(port) readl((port)->membase + AT91_US_CR) // is write-only | |
| /* PDC registers */ | |
| #define UART_PUT_PTCR(port,v) writel(v, (port)->membase + AT91_PDC_PTCR) | |
| #define UART_GET_PTSR(port) readl((port)->membase + AT91_PDC_PTSR) | |
| #define UART_PUT_RPR(port,v) writel(v, (port)->membase + AT91_PDC_RPR) | |
| #define UART_GET_RPR(port) readl((port)->membase + AT91_PDC_RPR) | |
| #define UART_PUT_RCR(port,v) writel(v, (port)->membase + AT91_PDC_RCR) | |
| #define UART_PUT_RNPR(port,v) writel(v, (port)->membase + AT91_PDC_RNPR) | |
| #define UART_PUT_RNCR(port,v) writel(v, (port)->membase + AT91_PDC_RNCR) | |
| #define UART_PUT_TPR(port,v) writel(v, (port)->membase + AT91_PDC_TPR) | |
| #define UART_PUT_TCR(port,v) writel(v, (port)->membase + AT91_PDC_TCR) | |
| //#define UART_PUT_TNPR(port,v) writel(v, (port)->membase + AT91_PDC_TNPR) | |
| //#define UART_PUT_TNCR(port,v) writel(v, (port)->membase + AT91_PDC_TNCR) | |
| static int (*at91_open)(struct uart_port *); | |
| static void (*at91_close)(struct uart_port *); | |
| /* | |
| * We wrap our port structure around the generic uart_port. | |
| */ | |
| struct at91_uart_port { | |
| struct uart_port uart; /* uart */ | |
| struct clk *clk; /* uart clock */ | |
| unsigned short suspended; /* is port suspended? */ | |
| }; | |
| static struct at91_uart_port at91_ports[AT91_NR_UART]; | |
| #ifdef SUPPORT_SYSRQ | |
| static struct console at91_console; | |
| #endif | |
| /* | |
| * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty. | |
| */ | |
| static u_int at91_tx_empty(struct uart_port *port) | |
| { | |
| return (UART_GET_CSR(port) & AT91_US_TXEMPTY) ? TIOCSER_TEMT : 0; | |
| } | |
| /* | |
| * Set state of the modem control output lines | |
| */ | |
| static void at91_set_mctrl(struct uart_port *port, u_int mctrl) | |
| { | |
| unsigned int control = 0; | |
| unsigned int mode; | |
| if (arch_identify() == ARCH_ID_AT91RM9200) { | |
| /* | |
| * AT91RM9200 Errata #39: RTS0 is not internally connected to PA21. | |
| * We need to drive the pin manually. | |
| */ | |
| if (port->mapbase == AT91_BASE_US0) { | |
| if (mctrl & TIOCM_RTS) | |
| at91_sys_write(AT91_PIOA + PIO_CODR, AT91_PA21_RTS0); | |
| else | |
| at91_sys_write(AT91_PIOA + PIO_SODR, AT91_PA21_RTS0); | |
| } | |
| } | |
| if (mctrl & TIOCM_RTS) | |
| control |= AT91_US_RTSEN; | |
| else | |
| control |= AT91_US_RTSDIS; | |
| if (mctrl & TIOCM_DTR) | |
| control |= AT91_US_DTREN; | |
| else | |
| control |= AT91_US_DTRDIS; | |
| UART_PUT_CR(port, control); | |
| /* Local loopback mode? */ | |
| mode = UART_GET_MR(port) & ~AT91_US_CHMODE; | |
| if (mctrl & TIOCM_LOOP) | |
| mode |= AT91_US_CHMODE_LOC_LOOP; | |
| else | |
| mode |= AT91_US_CHMODE_NORMAL; | |
| UART_PUT_MR(port, mode); | |
| } | |
| /* | |
| * Get state of the modem control input lines | |
| */ | |
| static u_int at91_get_mctrl(struct uart_port *port) | |
| { | |
| unsigned int status, ret = 0; | |
| status = UART_GET_CSR(port); | |
| /* | |
| * The control signals are active low. | |
| */ | |
| if (!(status & AT91_US_DCD)) | |
| ret |= TIOCM_CD; | |
| if (!(status & AT91_US_CTS)) | |
| ret |= TIOCM_CTS; | |
| if (!(status & AT91_US_DSR)) | |
| ret |= TIOCM_DSR; | |
| if (!(status & AT91_US_RI)) | |
| ret |= TIOCM_RI; | |
| return ret; | |
| } | |
| /* | |
| * Stop transmitting. | |
| */ | |
| static void at91_stop_tx(struct uart_port *port) | |
| { | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| UART_PUT_IDR(port, AT91_US_TXRDY); | |
| } | |
| /* | |
| * Start transmitting. | |
| */ | |
| static void at91_start_tx(struct uart_port *port) | |
| { | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| UART_PUT_IER(port, AT91_US_TXRDY); | |
| } | |
| /* | |
| * Stop receiving - port is in process of being closed. | |
| */ | |
| static void at91_stop_rx(struct uart_port *port) | |
| { | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| UART_PUT_IDR(port, AT91_US_RXRDY); | |
| } | |
| /* | |
| * Enable modem status interrupts | |
| */ | |
| static void at91_enable_ms(struct uart_port *port) | |
| { | |
| UART_PUT_IER(port, AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC); | |
| } | |
| /* | |
| * Control the transmission of a break signal | |
| */ | |
| static void at91_break_ctl(struct uart_port *port, int break_state) | |
| { | |
| if (break_state != 0) | |
| UART_PUT_CR(port, AT91_US_STTBRK); /* start break */ | |
| else | |
| UART_PUT_CR(port, AT91_US_STPBRK); /* stop break */ | |
| } | |
| /* | |
| * Characters received (called from interrupt handler) | |
| */ | |
| static void at91_rx_chars(struct uart_port *port, struct pt_regs *regs) | |
| { | |
| struct tty_struct *tty = port->info->tty; | |
| unsigned int status, ch, flg; | |
| status = UART_GET_CSR(port); | |
| while (status & AT91_US_RXRDY) { | |
| ch = UART_GET_CHAR(port); | |
| port->icount.rx++; | |
| flg = TTY_NORMAL; | |
| /* | |
| * note that the error handling code is | |
| * out of the main execution path | |
| */ | |
| if (unlikely(status & (AT91_US_PARE | AT91_US_FRAME | AT91_US_OVRE | AT91_US_RXBRK))) { | |
| UART_PUT_CR(port, AT91_US_RSTSTA); /* clear error */ | |
| if (status & AT91_US_RXBRK) { | |
| status &= ~(AT91_US_PARE | AT91_US_FRAME); /* ignore side-effect */ | |
| port->icount.brk++; | |
| if (uart_handle_break(port)) | |
| goto ignore_char; | |
| } | |
| if (status & AT91_US_PARE) | |
| port->icount.parity++; | |
| if (status & AT91_US_FRAME) | |
| port->icount.frame++; | |
| if (status & AT91_US_OVRE) | |
| port->icount.overrun++; | |
| status &= port->read_status_mask; | |
| if (status & AT91_US_RXBRK) | |
| flg = TTY_BREAK; | |
| else if (status & AT91_US_PARE) | |
| flg = TTY_PARITY; | |
| else if (status & AT91_US_FRAME) | |
| flg = TTY_FRAME; | |
| } | |
| if (uart_handle_sysrq_char(port, ch, regs)) | |
| goto ignore_char; | |
| uart_insert_char(port, status, AT91_US_OVRE, ch, flg); | |
| ignore_char: | |
| status = UART_GET_CSR(port); | |
| } | |
| tty_flip_buffer_push(tty); | |
| } | |
| /* | |
| * Transmit characters (called from interrupt handler) | |
| */ | |
| static void at91_tx_chars(struct uart_port *port) | |
| { | |
| struct circ_buf *xmit = &port->info->xmit; | |
| if (port->x_char) { | |
| UART_PUT_CHAR(port, port->x_char); | |
| port->icount.tx++; | |
| port->x_char = 0; | |
| return; | |
| } | |
| if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { | |
| at91_stop_tx(port); | |
| return; | |
| } | |
| while (UART_GET_CSR(port) & AT91_US_TXRDY) { | |
| UART_PUT_CHAR(port, xmit->buf[xmit->tail]); | |
| xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); | |
| port->icount.tx++; | |
| if (uart_circ_empty(xmit)) | |
| break; | |
| } | |
| if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) | |
| uart_write_wakeup(port); | |
| if (uart_circ_empty(xmit)) | |
| at91_stop_tx(port); | |
| } | |
| /* | |
| * Interrupt handler | |
| */ | |
| static irqreturn_t at91_interrupt(int irq, void *dev_id, struct pt_regs *regs) | |
| { | |
| struct uart_port *port = dev_id; | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| unsigned int status, pending, pass_counter = 0; | |
| status = UART_GET_CSR(port); | |
| pending = status & UART_GET_IMR(port); | |
| while (pending) { | |
| /* Interrupt receive */ | |
| if (pending & AT91_US_RXRDY) | |
| at91_rx_chars(port, regs); | |
| // TODO: All reads to CSR will clear these interrupts! | |
| if (pending & AT91_US_RIIC) port->icount.rng++; | |
| if (pending & AT91_US_DSRIC) port->icount.dsr++; | |
| if (pending & AT91_US_DCDIC) | |
| uart_handle_dcd_change(port, !(status & AT91_US_DCD)); | |
| if (pending & AT91_US_CTSIC) | |
| uart_handle_cts_change(port, !(status & AT91_US_CTS)); | |
| if (pending & (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC)) | |
| wake_up_interruptible(&port->info->delta_msr_wait); | |
| /* Interrupt transmit */ | |
| if (pending & AT91_US_TXRDY) | |
| at91_tx_chars(port); | |
| if (pass_counter++ > AT91_ISR_PASS_LIMIT) | |
| break; | |
| status = UART_GET_CSR(port); | |
| pending = status & UART_GET_IMR(port); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| /* | |
| * Perform initialization and enable port for reception | |
| */ | |
| static int at91_startup(struct uart_port *port) | |
| { | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| int retval; | |
| /* | |
| * Ensure that no interrupts are enabled otherwise when | |
| * request_irq() is called we could get stuck trying to | |
| * handle an unexpected interrupt | |
| */ | |
| UART_PUT_IDR(port, -1); | |
| /* | |
| * Allocate the IRQ | |
| */ | |
| retval = request_irq(port->irq, at91_interrupt, SA_SHIRQ, "at91_serial", port); | |
| if (retval) { | |
| printk("at91_serial: at91_startup - Can't get irq\n"); | |
| return retval; | |
| } | |
| /* | |
| * If there is a specific "open" function (to register | |
| * control line interrupts) | |
| */ | |
| if (at91_open) { | |
| retval = at91_open(port); | |
| if (retval) { | |
| free_irq(port->irq, port); | |
| return retval; | |
| } | |
| } | |
| /* | |
| * Finally, enable the serial port | |
| */ | |
| UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX); | |
| UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); /* enable xmit & rcvr */ | |
| UART_PUT_IER(port, AT91_US_RXRDY); /* enable receive only */ | |
| return 0; | |
| } | |
| /* | |
| * Disable the port | |
| */ | |
| static void at91_shutdown(struct uart_port *port) | |
| { | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| /* | |
| * Disable all interrupts, port and break condition. | |
| */ | |
| UART_PUT_CR(port, AT91_US_RSTSTA); | |
| UART_PUT_IDR(port, -1); | |
| /* | |
| * Free the interrupt | |
| */ | |
| free_irq(port->irq, port); | |
| /* | |
| * If there is a specific "close" function (to unregister | |
| * control line interrupts) | |
| */ | |
| if (at91_close) | |
| at91_close(port); | |
| } | |
| /* | |
| * Power / Clock management. | |
| */ | |
| static void at91_serial_pm(struct uart_port *port, unsigned int state, unsigned int oldstate) | |
| { | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| switch (state) { | |
| case 0: | |
| /* | |
| * Enable the peripheral clock for this serial port. | |
| * This is called on uart_open() or a resume event. | |
| */ | |
| clk_enable(at91_port->clk); | |
| break; | |
| case 3: | |
| /* | |
| * Disable the peripheral clock for this serial port. | |
| * This is called on uart_close() or a suspend event. | |
| */ | |
| clk_disable(at91_port->clk); | |
| break; | |
| default: | |
| printk(KERN_ERR "at91_serial: unknown pm %d\n", state); | |
| } | |
| } | |
| /* | |
| * Change the port parameters | |
| */ | |
| static void at91_set_termios(struct uart_port *port, struct termios * termios, struct termios * old) | |
| { | |
| unsigned long flags; | |
| unsigned int mode, imr, quot, baud; | |
| baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); | |
| quot = uart_get_divisor(port, baud); | |
| /* Get current mode register */ | |
| mode = UART_GET_MR(port) & ~(AT91_US_CHRL | AT91_US_NBSTOP | AT91_US_PAR); | |
| /* byte size */ | |
| switch (termios->c_cflag & CSIZE) { | |
| case CS5: | |
| mode |= AT91_US_CHRL_5; | |
| break; | |
| case CS6: | |
| mode |= AT91_US_CHRL_6; | |
| break; | |
| case CS7: | |
| mode |= AT91_US_CHRL_7; | |
| break; | |
| default: | |
| mode |= AT91_US_CHRL_8; | |
| break; | |
| } | |
| /* stop bits */ | |
| if (termios->c_cflag & CSTOPB) | |
| mode |= AT91_US_NBSTOP_2; | |
| /* parity */ | |
| if (termios->c_cflag & PARENB) { | |
| if (termios->c_cflag & CMSPAR) { /* Mark or Space parity */ | |
| if (termios->c_cflag & PARODD) | |
| mode |= AT91_US_PAR_MARK; | |
| else | |
| mode |= AT91_US_PAR_SPACE; | |
| } | |
| else if (termios->c_cflag & PARODD) | |
| mode |= AT91_US_PAR_ODD; | |
| else | |
| mode |= AT91_US_PAR_EVEN; | |
| } | |
| else | |
| mode |= AT91_US_PAR_NONE; | |
| spin_lock_irqsave(&port->lock, flags); | |
| port->read_status_mask = AT91_US_OVRE; | |
| if (termios->c_iflag & INPCK) | |
| port->read_status_mask |= (AT91_US_FRAME | AT91_US_PARE); | |
| if (termios->c_iflag & (BRKINT | PARMRK)) | |
| port->read_status_mask |= AT91_US_RXBRK; | |
| /* | |
| * Characters to ignore | |
| */ | |
| port->ignore_status_mask = 0; | |
| if (termios->c_iflag & IGNPAR) | |
| port->ignore_status_mask |= (AT91_US_FRAME | AT91_US_PARE); | |
| if (termios->c_iflag & IGNBRK) { | |
| port->ignore_status_mask |= AT91_US_RXBRK; | |
| /* | |
| * If we're ignoring parity and break indicators, | |
| * ignore overruns too (for real raw support). | |
| */ | |
| if (termios->c_iflag & IGNPAR) | |
| port->ignore_status_mask |= AT91_US_OVRE; | |
| } | |
| // TODO: Ignore all characters if CREAD is set. | |
| /* update the per-port timeout */ | |
| uart_update_timeout(port, termios->c_cflag, baud); | |
| /* disable interrupts and drain transmitter */ | |
| imr = UART_GET_IMR(port); /* get interrupt mask */ | |
| UART_PUT_IDR(port, -1); /* disable all interrupts */ | |
| while (!(UART_GET_CSR(port) & AT91_US_TXEMPTY)) { barrier(); } | |
| /* disable receiver and transmitter */ | |
| UART_PUT_CR(port, AT91_US_TXDIS | AT91_US_RXDIS); | |
| /* set the parity, stop bits and data size */ | |
| UART_PUT_MR(port, mode); | |
| /* set the baud rate */ | |
| UART_PUT_BRGR(port, quot); | |
| UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX); | |
| UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); | |
| /* restore interrupts */ | |
| UART_PUT_IER(port, imr); | |
| /* CTS flow-control and modem-status interrupts */ | |
| if (UART_ENABLE_MS(port, termios->c_cflag)) | |
| port->ops->enable_ms(port); | |
| spin_unlock_irqrestore(&port->lock, flags); | |
| } | |
| /* | |
| * Return string describing the specified port | |
| */ | |
| static const char *at91_type(struct uart_port *port) | |
| { | |
| return (port->type == PORT_AT91) ? "AT91_SERIAL" : NULL; | |
| } | |
| /* | |
| * Release the memory region(s) being used by 'port'. | |
| */ | |
| static void at91_release_port(struct uart_port *port) | |
| { | |
| struct platform_device *pdev = to_platform_device(port->dev); | |
| int size = pdev->resource[0].end - pdev->resource[0].start + 1; | |
| release_mem_region(port->mapbase, size); | |
| if (port->flags & UPF_IOREMAP) { | |
| iounmap(port->membase); | |
| port->membase = NULL; | |
| } | |
| } | |
| /* | |
| * Request the memory region(s) being used by 'port'. | |
| */ | |
| static int at91_request_port(struct uart_port *port) | |
| { | |
| struct platform_device *pdev = to_platform_device(port->dev); | |
| int size = pdev->resource[0].end - pdev->resource[0].start + 1; | |
| if (!request_mem_region(port->mapbase, size, "at91_serial")) | |
| return -EBUSY; | |
| if (port->flags & UPF_IOREMAP) { | |
| port->membase = ioremap(port->mapbase, size); | |
| if (port->membase == NULL) { | |
| release_mem_region(port->mapbase, size); | |
| return -ENOMEM; | |
| } | |
| } | |
| return 0; | |
| } | |
| /* | |
| * Configure/autoconfigure the port. | |
| */ | |
| static void at91_config_port(struct uart_port *port, int flags) | |
| { | |
| if (flags & UART_CONFIG_TYPE) { | |
| port->type = PORT_AT91; | |
| at91_request_port(port); | |
| } | |
| } | |
| /* | |
| * Verify the new serial_struct (for TIOCSSERIAL). | |
| */ | |
| static int at91_verify_port(struct uart_port *port, struct serial_struct *ser) | |
| { | |
| int ret = 0; | |
| if (ser->type != PORT_UNKNOWN && ser->type != PORT_AT91) | |
| ret = -EINVAL; | |
| if (port->irq != ser->irq) | |
| ret = -EINVAL; | |
| if (ser->io_type != SERIAL_IO_MEM) | |
| ret = -EINVAL; | |
| if (port->uartclk / 16 != ser->baud_base) | |
| ret = -EINVAL; | |
| if ((void *)port->mapbase != ser->iomem_base) | |
| ret = -EINVAL; | |
| if (port->iobase != ser->port) | |
| ret = -EINVAL; | |
| if (ser->hub6 != 0) | |
| ret = -EINVAL; | |
| return ret; | |
| } | |
| static struct uart_ops at91_pops = { | |
| .tx_empty = at91_tx_empty, | |
| .set_mctrl = at91_set_mctrl, | |
| .get_mctrl = at91_get_mctrl, | |
| .stop_tx = at91_stop_tx, | |
| .start_tx = at91_start_tx, | |
| .stop_rx = at91_stop_rx, | |
| .enable_ms = at91_enable_ms, | |
| .break_ctl = at91_break_ctl, | |
| .startup = at91_startup, | |
| .shutdown = at91_shutdown, | |
| .set_termios = at91_set_termios, | |
| .type = at91_type, | |
| .release_port = at91_release_port, | |
| .request_port = at91_request_port, | |
| .config_port = at91_config_port, | |
| .verify_port = at91_verify_port, | |
| .pm = at91_serial_pm, | |
| }; | |
| /* | |
| * Configure the port from the platform device resource info. | |
| */ | |
| static void __devinit at91_init_port(struct at91_uart_port *at91_port, struct platform_device *pdev) | |
| { | |
| struct uart_port *port = &at91_port->uart; | |
| struct at91_uart_data *data = pdev->dev.platform_data; | |
| port->iotype = UPIO_MEM; | |
| port->flags = UPF_BOOT_AUTOCONF; | |
| port->ops = &at91_pops; | |
| port->fifosize = 1; | |
| port->line = pdev->id; | |
| port->dev = &pdev->dev; | |
| port->mapbase = pdev->resource[0].start; | |
| port->irq = pdev->resource[1].start; | |
| if (port->mapbase == AT91_VA_BASE_SYS + AT91_DBGU) /* Part of system perpherals - already mapped */ | |
| port->membase = (void __iomem *) port->mapbase; | |
| else { | |
| port->flags |= UPF_IOREMAP; | |
| port->membase = NULL; | |
| } | |
| if (!at91_port->clk) { /* for console, the clock could already be configured */ | |
| at91_port->clk = clk_get(&pdev->dev, "usart"); | |
| clk_enable(at91_port->clk); | |
| port->uartclk = clk_get_rate(at91_port->clk); | |
| } | |
| } | |
| /* | |
| * Register board-specific modem-control line handlers. | |
| */ | |
| void __init at91_register_uart_fns(struct at91_port_fns *fns) | |
| { | |
| if (fns->enable_ms) | |
| at91_pops.enable_ms = fns->enable_ms; | |
| if (fns->get_mctrl) | |
| at91_pops.get_mctrl = fns->get_mctrl; | |
| if (fns->set_mctrl) | |
| at91_pops.set_mctrl = fns->set_mctrl; | |
| at91_open = fns->open; | |
| at91_close = fns->close; | |
| at91_pops.pm = fns->pm; | |
| at91_pops.set_wake = fns->set_wake; | |
| } | |
| #ifdef CONFIG_SERIAL_AT91_CONSOLE | |
| static void at91_console_putchar(struct uart_port *port, int ch) | |
| { | |
| while (!(UART_GET_CSR(port) & AT91_US_TXRDY)) | |
| barrier(); | |
| UART_PUT_CHAR(port, ch); | |
| } | |
| /* | |
| * Interrupts are disabled on entering | |
| */ | |
| static void at91_console_write(struct console *co, const char *s, u_int count) | |
| { | |
| struct uart_port *port = &at91_ports[co->index].uart; | |
| unsigned int status, imr; | |
| /* | |
| * First, save IMR and then disable interrupts | |
| */ | |
| imr = UART_GET_IMR(port); /* get interrupt mask */ | |
| UART_PUT_IDR(port, AT91_US_RXRDY | AT91_US_TXRDY); | |
| uart_console_write(port, s, count, at91_console_putchar); | |
| /* | |
| * Finally, wait for transmitter to become empty | |
| * and restore IMR | |
| */ | |
| do { | |
| status = UART_GET_CSR(port); | |
| } while (!(status & AT91_US_TXRDY)); | |
| UART_PUT_IER(port, imr); /* set interrupts back the way they were */ | |
| } | |
| /* | |
| * If the port was already initialised (eg, by a boot loader), try to determine | |
| * the current setup. | |
| */ | |
| static void __init at91_console_get_options(struct uart_port *port, int *baud, int *parity, int *bits) | |
| { | |
| unsigned int mr, quot; | |
| // TODO: CR is a write-only register | |
| // unsigned int cr; | |
| // | |
| // cr = UART_GET_CR(port) & (AT91_US_RXEN | AT91_US_TXEN); | |
| // if (cr == (AT91_US_RXEN | AT91_US_TXEN)) { | |
| // /* ok, the port was enabled */ | |
| // } | |
| mr = UART_GET_MR(port) & AT91_US_CHRL; | |
| if (mr == AT91_US_CHRL_8) | |
| *bits = 8; | |
| else | |
| *bits = 7; | |
| mr = UART_GET_MR(port) & AT91_US_PAR; | |
| if (mr == AT91_US_PAR_EVEN) | |
| *parity = 'e'; | |
| else if (mr == AT91_US_PAR_ODD) | |
| *parity = 'o'; | |
| quot = UART_GET_BRGR(port); | |
| *baud = port->uartclk / (16 * (quot)); | |
| } | |
| static int __init at91_console_setup(struct console *co, char *options) | |
| { | |
| struct uart_port *port = &at91_ports[co->index].uart; | |
| int baud = 115200; | |
| int bits = 8; | |
| int parity = 'n'; | |
| int flow = 'n'; | |
| if (port->membase == 0) /* Port not initialized yet - delay setup */ | |
| return -ENODEV; | |
| UART_PUT_IDR(port, -1); /* disable interrupts */ | |
| UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX); | |
| UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); | |
| if (options) | |
| uart_parse_options(options, &baud, &parity, &bits, &flow); | |
| else | |
| at91_console_get_options(port, &baud, &parity, &bits); | |
| return uart_set_options(port, co, baud, parity, bits, flow); | |
| } | |
| static struct uart_driver at91_uart; | |
| static struct console at91_console = { | |
| .name = AT91_DEVICENAME, | |
| .write = at91_console_write, | |
| .device = uart_console_device, | |
| .setup = at91_console_setup, | |
| .flags = CON_PRINTBUFFER, | |
| .index = -1, | |
| .data = &at91_uart, | |
| }; | |
| #define AT91_CONSOLE_DEVICE &at91_console | |
| /* | |
| * Early console initialization (before VM subsystem initialized). | |
| */ | |
| static int __init at91_console_init(void) | |
| { | |
| if (at91_default_console_device) { | |
| add_preferred_console(AT91_DEVICENAME, at91_default_console_device->id, NULL); | |
| at91_init_port(&(at91_ports[at91_default_console_device->id]), at91_default_console_device); | |
| register_console(&at91_console); | |
| } | |
| return 0; | |
| } | |
| console_initcall(at91_console_init); | |
| /* | |
| * Late console initialization. | |
| */ | |
| static int __init at91_late_console_init(void) | |
| { | |
| if (at91_default_console_device && !(at91_console.flags & CON_ENABLED)) | |
| register_console(&at91_console); | |
| return 0; | |
| } | |
| core_initcall(at91_late_console_init); | |
| #else | |
| #define AT91_CONSOLE_DEVICE NULL | |
| #endif | |
| static struct uart_driver at91_uart = { | |
| .owner = THIS_MODULE, | |
| .driver_name = "at91_serial", | |
| .dev_name = AT91_DEVICENAME, | |
| .devfs_name = AT91_DEVICENAME, | |
| .major = SERIAL_AT91_MAJOR, | |
| .minor = MINOR_START, | |
| .nr = AT91_NR_UART, | |
| .cons = AT91_CONSOLE_DEVICE, | |
| }; | |
| #ifdef CONFIG_PM | |
| static int at91_serial_suspend(struct platform_device *pdev, pm_message_t state) | |
| { | |
| struct uart_port *port = platform_get_drvdata(pdev); | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| if (device_may_wakeup(&pdev->dev) && !at91_suspend_entering_slow_clock()) | |
| enable_irq_wake(port->irq); | |
| else { | |
| disable_irq_wake(port->irq); | |
| uart_suspend_port(&at91_uart, port); | |
| at91_port->suspended = 1; | |
| } | |
| return 0; | |
| } | |
| static int at91_serial_resume(struct platform_device *pdev) | |
| { | |
| struct uart_port *port = platform_get_drvdata(pdev); | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| if (at91_port->suspended) { | |
| uart_resume_port(&at91_uart, port); | |
| at91_port->suspended = 0; | |
| } | |
| return 0; | |
| } | |
| #else | |
| #define at91_serial_suspend NULL | |
| #define at91_serial_resume NULL | |
| #endif | |
| static int __devinit at91_serial_probe(struct platform_device *pdev) | |
| { | |
| struct at91_uart_port *port; | |
| int ret; | |
| port = &at91_ports[pdev->id]; | |
| at91_init_port(port, pdev); | |
| ret = uart_add_one_port(&at91_uart, &port->uart); | |
| if (!ret) { | |
| device_init_wakeup(&pdev->dev, 1); | |
| platform_set_drvdata(pdev, port); | |
| } | |
| return ret; | |
| } | |
| static int __devexit at91_serial_remove(struct platform_device *pdev) | |
| { | |
| struct uart_port *port = platform_get_drvdata(pdev); | |
| struct at91_uart_port *at91_port = (struct at91_uart_port *) port; | |
| int ret = 0; | |
| clk_disable(at91_port->clk); | |
| clk_put(at91_port->clk); | |
| device_init_wakeup(&pdev->dev, 0); | |
| platform_set_drvdata(pdev, NULL); | |
| if (port) { | |
| ret = uart_remove_one_port(&at91_uart, port); | |
| kfree(port); | |
| } | |
| return ret; | |
| } | |
| static struct platform_driver at91_serial_driver = { | |
| .probe = at91_serial_probe, | |
| .remove = __devexit_p(at91_serial_remove), | |
| .suspend = at91_serial_suspend, | |
| .resume = at91_serial_resume, | |
| .driver = { | |
| .name = "at91_usart", | |
| .owner = THIS_MODULE, | |
| }, | |
| }; | |
| static int __init at91_serial_init(void) | |
| { | |
| int ret; | |
| ret = uart_register_driver(&at91_uart); | |
| if (ret) | |
| return ret; | |
| ret = platform_driver_register(&at91_serial_driver); | |
| if (ret) | |
| uart_unregister_driver(&at91_uart); | |
| return ret; | |
| } | |
| static void __exit at91_serial_exit(void) | |
| { | |
| platform_driver_unregister(&at91_serial_driver); | |
| uart_unregister_driver(&at91_uart); | |
| } | |
| module_init(at91_serial_init); | |
| module_exit(at91_serial_exit); | |
| MODULE_AUTHOR("Rick Bronson"); | |
| MODULE_DESCRIPTION("AT91 generic serial port driver"); | |
| MODULE_LICENSE("GPL"); |