| # | |
| # I2C Sensor chip drivers configuration | |
| # | |
| menu "Hardware Monitoring support" | |
| config HWMON | |
| tristate "Hardware Monitoring support" | |
| default y | |
| help | |
| Hardware monitoring devices let you monitor the hardware health | |
| of a system. Most modern motherboards include such a device. It | |
| can include temperature sensors, voltage sensors, fan speed | |
| sensors and various additional features such as the ability to | |
| control the speed of the fans. If you want this support you | |
| should say Y here and also to the specific driver(s) for your | |
| sensors chip(s) below. | |
| This support can also be built as a module. If so, the module | |
| will be called hwmon. | |
| config HWMON_VID | |
| tristate | |
| default n | |
| config SENSORS_ADM1021 | |
| tristate "Analog Devices ADM1021 and compatibles" | |
| depends on HWMON && I2C | |
| help | |
| If you say yes here you get support for Analog Devices ADM1021 | |
| and ADM1023 sensor chips and clones: Maxim MAX1617 and MAX1617A, | |
| Genesys Logic GL523SM, National Semiconductor LM84, TI THMC10, | |
| and the XEON processor built-in sensor. | |
| This driver can also be built as a module. If so, the module | |
| will be called adm1021. | |
| config SENSORS_ADM1025 | |
| tristate "Analog Devices ADM1025 and compatibles" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for Analog Devices ADM1025 | |
| and Philips NE1619 sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called adm1025. | |
| config SENSORS_ADM1026 | |
| tristate "Analog Devices ADM1026 and compatibles" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for Analog Devices ADM1026 | |
| sensor chip. | |
| This driver can also be built as a module. If so, the module | |
| will be called adm1026. | |
| config SENSORS_ADM1031 | |
| tristate "Analog Devices ADM1031 and compatibles" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for Analog Devices ADM1031 | |
| and ADM1030 sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called adm1031. | |
| config SENSORS_ADM9240 | |
| tristate "Analog Devices ADM9240 and compatibles" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for Analog Devices ADM9240, | |
| Dallas DS1780, National Semiconductor LM81 sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called adm9240. | |
| config SENSORS_ASB100 | |
| tristate "Asus ASB100 Bach" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for the ASB100 Bach sensor | |
| chip found on some Asus mainboards. | |
| This driver can also be built as a module. If so, the module | |
| will be called asb100. | |
| config SENSORS_ATXP1 | |
| tristate "Attansic ATXP1 VID controller" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for the Attansic ATXP1 VID | |
| controller. | |
| If your board have such a chip, you are able to control your CPU | |
| core and other voltages. | |
| This driver can also be built as a module. If so, the module | |
| will be called atxp1. | |
| config SENSORS_DS1621 | |
| tristate "Dallas Semiconductor DS1621 and DS1625" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for Dallas Semiconductor | |
| DS1621 and DS1625 sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called ds1621. | |
| config SENSORS_F71805F | |
| tristate "Fintek F71805F/FG" | |
| depends on HWMON && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for hardware monitoring | |
| features of the Fintek F71805F/FG chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called f71805f. | |
| config SENSORS_FSCHER | |
| tristate "FSC Hermes" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for Fujitsu Siemens | |
| Computers Hermes sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called fscher. | |
| config SENSORS_FSCPOS | |
| tristate "FSC Poseidon" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for Fujitsu Siemens | |
| Computers Poseidon sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called fscpos. | |
| config SENSORS_GL518SM | |
| tristate "Genesys Logic GL518SM" | |
| depends on HWMON && I2C | |
| help | |
| If you say yes here you get support for Genesys Logic GL518SM | |
| sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called gl518sm. | |
| config SENSORS_GL520SM | |
| tristate "Genesys Logic GL520SM" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for Genesys Logic GL520SM | |
| sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called gl520sm. | |
| config SENSORS_IT87 | |
| tristate "ITE IT87xx and compatibles" | |
| depends on HWMON && I2C | |
| select I2C_ISA | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for ITE IT87xx sensor chips | |
| and clones: SiS960. | |
| This driver can also be built as a module. If so, the module | |
| will be called it87. | |
| config SENSORS_LM63 | |
| tristate "National Semiconductor LM63" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for the National Semiconductor | |
| LM63 remote diode digital temperature sensor with integrated fan | |
| control. Such chips are found on the Tyan S4882 (Thunder K8QS Pro) | |
| motherboard, among others. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm63. | |
| config SENSORS_LM75 | |
| tristate "National Semiconductor LM75 and compatibles" | |
| depends on HWMON && I2C | |
| help | |
| If you say yes here you get support for National Semiconductor LM75 | |
| sensor chips and clones: Dallas Semiconductor DS75 and DS1775 (in | |
| 9-bit precision mode), and TelCom (now Microchip) TCN75. | |
| The DS75 and DS1775 in 10- to 12-bit precision modes will require | |
| a force module parameter. The driver will not handle the extra | |
| precision anyhow. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm75. | |
| config SENSORS_LM77 | |
| tristate "National Semiconductor LM77" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for National Semiconductor LM77 | |
| sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm77. | |
| config SENSORS_LM78 | |
| tristate "National Semiconductor LM78 and compatibles" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select I2C_ISA | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for National Semiconductor LM78, | |
| LM78-J and LM79. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm78. | |
| config SENSORS_LM80 | |
| tristate "National Semiconductor LM80" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for National Semiconductor | |
| LM80 sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm80. | |
| config SENSORS_LM83 | |
| tristate "National Semiconductor LM83" | |
| depends on HWMON && I2C | |
| help | |
| If you say yes here you get support for National Semiconductor | |
| LM83 sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm83. | |
| config SENSORS_LM85 | |
| tristate "National Semiconductor LM85 and compatibles" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for National Semiconductor LM85 | |
| sensor chips and clones: ADT7463, EMC6D100, EMC6D102 and ADM1027. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm85. | |
| config SENSORS_LM87 | |
| tristate "National Semiconductor LM87" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for National Semiconductor LM87 | |
| sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm87. | |
| config SENSORS_LM90 | |
| tristate "National Semiconductor LM90 and compatibles" | |
| depends on HWMON && I2C | |
| help | |
| If you say yes here you get support for National Semiconductor LM90, | |
| LM86, LM89 and LM99, Analog Devices ADM1032 and Maxim MAX6657 and | |
| MAX6658 sensor chips. | |
| The Analog Devices ADT7461 sensor chip is also supported, but only | |
| if found in ADM1032 compatibility mode. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm90. | |
| config SENSORS_LM92 | |
| tristate "National Semiconductor LM92 and compatibles" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for National Semiconductor LM92 | |
| and Maxim MAX6635 sensor chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called lm92. | |
| config SENSORS_MAX1619 | |
| tristate "Maxim MAX1619 sensor chip" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for MAX1619 sensor chip. | |
| This driver can also be built as a module. If so, the module | |
| will be called max1619. | |
| config SENSORS_PC87360 | |
| tristate "National Semiconductor PC87360 family" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select I2C_ISA | |
| select HWMON_VID | |
| help | |
| If you say yes here you get access to the hardware monitoring | |
| functions of the National Semiconductor PC8736x Super-I/O chips. | |
| The PC87360, PC87363 and PC87364 only have fan monitoring and | |
| control. The PC87365 and PC87366 additionally have voltage and | |
| temperature monitoring. | |
| This driver can also be built as a module. If so, the module | |
| will be called pc87360. | |
| config SENSORS_SIS5595 | |
| tristate "Silicon Integrated Systems Corp. SiS5595" | |
| depends on HWMON && I2C && PCI && EXPERIMENTAL | |
| select I2C_ISA | |
| help | |
| If you say yes here you get support for the integrated sensors in | |
| SiS5595 South Bridges. | |
| This driver can also be built as a module. If so, the module | |
| will be called sis5595. | |
| config SENSORS_SMSC47M1 | |
| tristate "SMSC LPC47M10x and compatibles" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select I2C_ISA | |
| help | |
| If you say yes here you get support for the integrated fan | |
| monitoring and control capabilities of the SMSC LPC47B27x, | |
| LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x and LPC47M192 chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called smsc47m1. | |
| config SENSORS_SMSC47B397 | |
| tristate "SMSC LPC47B397-NC" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select I2C_ISA | |
| help | |
| If you say yes here you get support for the SMSC LPC47B397-NC | |
| sensor chip. | |
| This driver can also be built as a module. If so, the module | |
| will be called smsc47b397. | |
| config SENSORS_VIA686A | |
| tristate "VIA686A" | |
| depends on HWMON && I2C && PCI | |
| select I2C_ISA | |
| help | |
| If you say yes here you get support for the integrated sensors in | |
| Via 686A/B South Bridges. | |
| This driver can also be built as a module. If so, the module | |
| will be called via686a. | |
| config SENSORS_VT8231 | |
| tristate "VT8231" | |
| depends on HWMON && I2C && PCI && EXPERIMENTAL | |
| select HWMON_VID | |
| select I2C_ISA | |
| help | |
| If you say yes here then you get support for the integrated sensors | |
| in the VIA VT8231 device. | |
| This driver can also be built as a module. If so, the module | |
| will be called vt8231. | |
| config SENSORS_W83781D | |
| tristate "Winbond W83781D, W83782D, W83783S, W83627HF, Asus AS99127F" | |
| depends on HWMON && I2C | |
| select I2C_ISA | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for the Winbond W8378x series | |
| of sensor chips: the W83781D, W83782D, W83783S and W83627HF, | |
| and the similar Asus AS99127F. | |
| This driver can also be built as a module. If so, the module | |
| will be called w83781d. | |
| config SENSORS_W83792D | |
| tristate "Winbond W83792D" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for the Winbond W83792D chip. | |
| This driver can also be built as a module. If so, the module | |
| will be called w83792d. | |
| config SENSORS_W83L785TS | |
| tristate "Winbond W83L785TS-S" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for the Winbond W83L785TS-S | |
| sensor chip, which is used on the Asus A7N8X, among other | |
| motherboards. | |
| This driver can also be built as a module. If so, the module | |
| will be called w83l785ts. | |
| config SENSORS_W83627HF | |
| tristate "Winbond W83627HF, W83627THF, W83637HF, W83687THF, W83697HF" | |
| depends on HWMON && I2C | |
| select I2C_ISA | |
| select HWMON_VID | |
| help | |
| If you say yes here you get support for the Winbond W836X7 series | |
| of sensor chips: the W83627HF, W83627THF, W83637HF, W83687THF and | |
| W83697HF. | |
| This driver can also be built as a module. If so, the module | |
| will be called w83627hf. | |
| config SENSORS_W83627EHF | |
| tristate "Winbond W83627EHF" | |
| depends on HWMON && I2C && EXPERIMENTAL | |
| select I2C_ISA | |
| help | |
| If you say yes here you get preliminary support for the hardware | |
| monitoring functionality of the Winbond W83627EHF Super-I/O chip. | |
| Only fan and temperature inputs are supported at the moment, while | |
| the chip does much more than that. | |
| This driver also supports the W83627EHG, which is the lead-free | |
| version of the W83627EHF. | |
| This driver can also be built as a module. If so, the module | |
| will be called w83627ehf. | |
| config SENSORS_HDAPS | |
| tristate "IBM Hard Drive Active Protection System (hdaps)" | |
| depends on HWMON && INPUT && X86 | |
| default n | |
| help | |
| This driver provides support for the IBM Hard Drive Active Protection | |
| System (hdaps), which provides an accelerometer and other misc. data. | |
| ThinkPads starting with the R50, T41, and X40 are supported. The | |
| accelerometer data is readable via sysfs. | |
| This driver also provides an absolute input class device, allowing | |
| the laptop to act as a pinball machine-esque joystick. | |
| Say Y here if you have an applicable laptop and want to experience | |
| the awesome power of hdaps. | |
| config HWMON_DEBUG_CHIP | |
| bool "Hardware Monitoring Chip debugging messages" | |
| depends on HWMON | |
| default n | |
| help | |
| Say Y here if you want the I2C chip drivers to produce a bunch of | |
| debug messages to the system log. Select this if you are having | |
| a problem with I2C support and want to see more of what is going | |
| on. | |
| endmenu |