| /* | |
| * BRIEF MODULE DESCRIPTION | |
| * Momentum Computer Ocelot-G (CP7000G) - board dependent boot routines | |
| * | |
| * Copyright (C) 1996, 1997, 2001 Ralf Baechle | |
| * Copyright (C) 2000 RidgeRun, Inc. | |
| * Copyright (C) 2001 Red Hat, Inc. | |
| * Copyright (C) 2002 Momentum Computer | |
| * | |
| * Author: Matthew Dharm, Momentum Computer | |
| * mdharm@momenco.com | |
| * | |
| * Author: RidgeRun, Inc. | |
| * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com | |
| * | |
| * Copyright 2001 MontaVista Software Inc. | |
| * Author: jsun@mvista.com or jsun@junsun.net | |
| * | |
| * This program is free software; you can redistribute it and/or modify it | |
| * under the terms of the GNU General Public License as published by the | |
| * Free Software Foundation; either version 2 of the License, or (at your | |
| * option) any later version. | |
| * | |
| * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED | |
| * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN | |
| * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, | |
| * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT | |
| * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF | |
| * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON | |
| * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT | |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF | |
| * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
| * | |
| * You should have received a copy of the GNU General Public License along | |
| * with this program; if not, write to the Free Software Foundation, Inc., | |
| * 675 Mass Ave, Cambridge, MA 02139, USA. | |
| * | |
| */ | |
| #include <linux/config.h> | |
| #include <linux/init.h> | |
| #include <linux/kernel.h> | |
| #include <linux/types.h> | |
| #include <linux/mm.h> | |
| #include <linux/swap.h> | |
| #include <linux/ioport.h> | |
| #include <linux/sched.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/pci.h> | |
| #include <linux/pm.h> | |
| #include <linux/timex.h> | |
| #include <linux/vmalloc.h> | |
| #include <asm/time.h> | |
| #include <asm/bootinfo.h> | |
| #include <asm/page.h> | |
| #include <asm/io.h> | |
| #include <asm/gt64240.h> | |
| #include <asm/irq.h> | |
| #include <asm/pci.h> | |
| #include <asm/processor.h> | |
| #include <asm/ptrace.h> | |
| #include <asm/reboot.h> | |
| #include <linux/bootmem.h> | |
| #include "ocelot_pld.h" | |
| #ifdef CONFIG_GALILLEO_GT64240_ETH | |
| extern unsigned char prom_mac_addr_base[6]; | |
| #endif | |
| unsigned long marvell_base; | |
| /* These functions are used for rebooting or halting the machine*/ | |
| extern void momenco_ocelot_restart(char *command); | |
| extern void momenco_ocelot_halt(void); | |
| extern void momenco_ocelot_power_off(void); | |
| extern void gt64240_time_init(void); | |
| extern void momenco_ocelot_irq_setup(void); | |
| static char reset_reason; | |
| static unsigned long ENTRYLO(unsigned long paddr) | |
| { | |
| return ((paddr & PAGE_MASK) | | |
| (_PAGE_PRESENT | __READABLE | __WRITEABLE | _PAGE_GLOBAL | | |
| _CACHE_UNCACHED)) >> 6; | |
| } | |
| /* setup code for a handoff from a version 2 PMON 2000 PROM */ | |
| void PMON_v2_setup(void) | |
| { | |
| /* A wired TLB entry for the GT64240 and the serial port. The | |
| GT64240 is going to be hit on every IRQ anyway - there's | |
| absolutely no point in letting it be a random TLB entry, as | |
| it'll just cause needless churning of the TLB. And we use | |
| the other half for the serial port, which is just a PITA | |
| otherwise :) | |
| Device Physical Virtual | |
| GT64240 Internal Regs 0xf4000000 0xe0000000 | |
| UARTs (CS2) 0xfd000000 0xe0001000 | |
| */ | |
| add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), | |
| 0xf4000000, PM_64K); | |
| add_wired_entry(ENTRYLO(0xfd000000), ENTRYLO(0xfd001000), | |
| 0xfd000000, PM_4K); | |
| /* Also a temporary entry to let us talk to the Ocelot PLD and NVRAM | |
| in the CS[012] region. We can't use ioremap() yet. The NVRAM | |
| is a ST M48T37Y, which includes NVRAM, RTC, and Watchdog functions. | |
| Ocelot PLD (CS0) 0xfc000000 0xe0020000 | |
| NVRAM (CS1) 0xfc800000 0xe0030000 | |
| */ | |
| add_temporary_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfc010000), | |
| 0xfc000000, PM_64K); | |
| add_temporary_entry(ENTRYLO(0xfc800000), ENTRYLO(0xfc810000), | |
| 0xfc800000, PM_64K); | |
| marvell_base = 0xf4000000; | |
| } | |
| extern int rm7k_tcache_enabled; | |
| /* | |
| * This runs in KSEG1. See the verbiage in rm7k.c::probe_scache() | |
| */ | |
| #define Page_Invalidate_T 0x16 | |
| static void __init setup_l3cache(unsigned long size) | |
| { | |
| int register i; | |
| printk("Enabling L3 cache..."); | |
| /* Enable the L3 cache in the GT64120A's CPU Configuration register */ | |
| MV_WRITE(0, MV_READ(0) | (1<<14)); | |
| /* Enable the L3 cache in the CPU */ | |
| set_c0_config(1<<12 /* CONF_TE */); | |
| /* Clear the cache */ | |
| write_c0_taglo(0); | |
| write_c0_taghi(0); | |
| for (i=0; i < size; i+= 4096) { | |
| __asm__ __volatile__ ( | |
| ".set noreorder\n\t" | |
| ".set mips3\n\t" | |
| "cache %1, (%0)\n\t" | |
| ".set mips0\n\t" | |
| ".set reorder" | |
| : | |
| : "r" (KSEG0ADDR(i)), | |
| "i" (Page_Invalidate_T)); | |
| } | |
| /* Let the RM7000 MM code know that the tertiary cache is enabled */ | |
| rm7k_tcache_enabled = 1; | |
| printk("Done\n"); | |
| } | |
| void __init plat_mem_setup(void) | |
| { | |
| void (*l3func)(unsigned long) = (void *) KSEG1ADDR(setup_l3cache); | |
| unsigned int tmpword; | |
| board_time_init = gt64240_time_init; | |
| _machine_restart = momenco_ocelot_restart; | |
| _machine_halt = momenco_ocelot_halt; | |
| pm_power_off = momenco_ocelot_power_off; | |
| /* | |
| * initrd_start = (ulong)ocelot_initrd_start; | |
| * initrd_end = (ulong)ocelot_initrd_start + (ulong)ocelot_initrd_size; | |
| * initrd_below_start_ok = 1; | |
| */ | |
| /* do handoff reconfiguration */ | |
| PMON_v2_setup(); | |
| #ifdef CONFIG_GALILLEO_GT64240_ETH | |
| /* get the mac addr */ | |
| memcpy(prom_mac_addr_base, (void*)0xfc807cf2, 6); | |
| #endif | |
| /* Turn off the Bit-Error LED */ | |
| OCELOT_PLD_WRITE(0x80, INTCLR); | |
| tmpword = OCELOT_PLD_READ(BOARDREV); | |
| if (tmpword < 26) | |
| printk("Momenco Ocelot-G: Board Assembly Rev. %c\n", 'A'+tmpword); | |
| else | |
| printk("Momenco Ocelot-G: Board Assembly Revision #0x%x\n", tmpword); | |
| tmpword = OCELOT_PLD_READ(PLD1_ID); | |
| printk("PLD 1 ID: %d.%d\n", tmpword>>4, tmpword&15); | |
| tmpword = OCELOT_PLD_READ(PLD2_ID); | |
| printk("PLD 2 ID: %d.%d\n", tmpword>>4, tmpword&15); | |
| tmpword = OCELOT_PLD_READ(RESET_STATUS); | |
| printk("Reset reason: 0x%x\n", tmpword); | |
| reset_reason = tmpword; | |
| OCELOT_PLD_WRITE(0xff, RESET_STATUS); | |
| tmpword = OCELOT_PLD_READ(BOARD_STATUS); | |
| printk("Board Status register: 0x%02x\n", tmpword); | |
| printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent"); | |
| printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent"); | |
| printk(" - Tulip PHY %s connected\n", (tmpword&0x10)?"is":"not"); | |
| printk(" - L3 Cache size: %d MiB\n", (1<<((tmpword&12) >> 2))&~1); | |
| printk(" - SDRAM size: %d MiB\n", 1<<(6+(tmpword&3))); | |
| if (tmpword&12) | |
| l3func((1<<(((tmpword&12) >> 2)+20))); | |
| switch(tmpword &3) { | |
| case 3: | |
| /* 512MiB -- two banks of 256MiB */ | |
| add_memory_region( 0x0<<20, 0x100<<20, BOOT_MEM_RAM); | |
| /* | |
| add_memory_region(0x100<<20, 0x100<<20, BOOT_MEM_RAM); | |
| */ | |
| break; | |
| case 2: | |
| /* 256MiB -- two banks of 128MiB */ | |
| add_memory_region( 0x0<<20, 0x80<<20, BOOT_MEM_RAM); | |
| add_memory_region(0x80<<20, 0x80<<20, BOOT_MEM_RAM); | |
| break; | |
| case 1: | |
| /* 128MiB -- 64MiB per bank */ | |
| add_memory_region( 0x0<<20, 0x40<<20, BOOT_MEM_RAM); | |
| add_memory_region(0x40<<20, 0x40<<20, BOOT_MEM_RAM); | |
| break; | |
| case 0: | |
| /* 64MiB */ | |
| add_memory_region( 0x0<<20, 0x40<<20, BOOT_MEM_RAM); | |
| break; | |
| } | |
| /* FIXME: Fix up the DiskOnChip mapping */ | |
| MV_WRITE(0x468, 0xfef73); | |
| } | |
| /* This needs to be one of the first initcalls, because no I/O port access | |
| can work before this */ | |
| static int io_base_ioremap(void) | |
| { | |
| /* we're mapping PCI accesses from 0xc0000000 to 0xf0000000 */ | |
| unsigned long io_remap_range; | |
| io_remap_range = (unsigned long) ioremap(0xc0000000, 0x30000000); | |
| if (!io_remap_range) | |
| panic("Could not ioremap I/O port range"); | |
| set_io_port_base(io_remap_range - 0xc0000000); | |
| return 0; | |
| } | |
| module_init(io_base_ioremap); |