| /* lcd-panel.h | |
| $Id$ | |
| written by Marc Singer | |
| 18 Jul 2005 | |
| Copyright (C) 2005 Marc Singer | |
| ----------- | |
| DESCRIPTION | |
| ----------- | |
| Only one panel may be defined at a time. | |
| The pixel clock is calculated to be no greater than the target. | |
| Each timing value is accompanied by a specification comment. | |
| UNITS/MIN/TYP/MAX | |
| Most of the units will be in clocks. | |
| USE_RGB555 | |
| Define this macro to configure the AMBA LCD controller to use an | |
| RGB555 encoding for the pels instead of the normal RGB565. | |
| LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11 | |
| These boards are best approximated by 555 for all panels. Some | |
| can use an extra low-order bit of blue in bit 16 of the color | |
| value, but we don't have a way to communicate this non-linear | |
| mapping to the kernel. | |
| */ | |
| #if !defined (__LCD_PANEL_H__) | |
| # define __LCD_PANEL_H__ | |
| #if defined (MACH_LPD79520)\ | |
| || defined (MACH_LPD79524)\ | |
| || defined (MACH_LPD7A400)\ | |
| || defined (MACH_LPD7A404) | |
| # define USE_RGB555 | |
| #endif | |
| struct clcd_panel_extra { | |
| unsigned int hrmode; | |
| unsigned int clsen; | |
| unsigned int spsen; | |
| unsigned int pcdel; | |
| unsigned int revdel; | |
| unsigned int lpdel; | |
| unsigned int spldel; | |
| unsigned int pc2del; | |
| }; | |
| #define NS_TO_CLOCK(ns,c) ((((ns)*((c)/1000) + (1000000 - 1))/1000000)) | |
| #define CLOCK_TO_DIV(e,c) (((c) + (e) - 1)/(e)) | |
| #if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT | |
| /* Logic Product Development LCD 3.5" QVGA HRTFT -10 */ | |
| /* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */ | |
| #define PIX_CLOCK_TARGET (6800000) | |
| #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) | |
| #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) | |
| static struct clcd_panel lcd_panel = { | |
| .mode = { | |
| .name = "3.5in QVGA (LQ035Q7DB02)", | |
| .xres = 240, | |
| .yres = 320, | |
| .pixclock = PIX_CLOCK, | |
| .left_margin = 16, | |
| .right_margin = 21, | |
| .upper_margin = 8, // line/8/8/8 | |
| .lower_margin = 5, | |
| .hsync_len = 61, | |
| .vsync_len = NS_TO_CLOCK (60, PIX_CLOCK), | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_IPC | (PIX_CLOCK_DIVIDER - 2), | |
| .cntl = CNTL_LCDTFT | CNTL_WATERMARK, | |
| .bpp = 16, | |
| }; | |
| #define HAS_LCD_PANEL_EXTRA | |
| static struct clcd_panel_extra lcd_panel_extra = { | |
| .hrmode = 1, | |
| .clsen = 1, | |
| .spsen = 1, | |
| .pcdel = 8, | |
| .revdel = 7, | |
| .lpdel = 13, | |
| .spldel = 77, | |
| .pc2del = 208, | |
| }; | |
| #endif | |
| #if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02 | |
| /* Logic Product Development LCD 5.7" QVGA -10 */ | |
| /* Sharp PN LQ057Q3DC02 */ | |
| /* QVGA mode, V/Q=LOW */ | |
| /* From Sharp on 2006.1.3. I believe some of the values are incorrect | |
| * based on the datasheet. | |
| Timing0 TIMING1 TIMING2 CONTROL | |
| 0x140A0C4C 0x080504EF 0x013F380D 0x00000829 | |
| HBP= 20 VBP= 8 BCD= 0 | |
| HFP= 10 VFP= 5 CPL=319 | |
| HSW= 12 VSW= 1 IOE= 0 | |
| PPL= 19 LPP=239 IPC= 1 | |
| IHS= 1 | |
| IVS= 1 | |
| ACB= 0 | |
| CSEL= 0 | |
| PCD= 13 | |
| */ | |
| /* The full horozontal cycle (Th) is clock/360/400/450. */ | |
| /* The full vertical cycle (Tv) is line/251/262/280. */ | |
| #define PIX_CLOCK_TARGET (6300000) /* -/6.3/7 MHz */ | |
| #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) | |
| #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) | |
| static struct clcd_panel lcd_panel = { | |
| .mode = { | |
| .name = "5.7in QVGA (LQ057Q3DC02)", | |
| .xres = 320, | |
| .yres = 240, | |
| .pixclock = PIX_CLOCK, | |
| .left_margin = 11, | |
| .right_margin = 400-11-320-2, | |
| .upper_margin = 7, // line/7/7/7 | |
| .lower_margin = 262-7-240-2, | |
| .hsync_len = 2, // clk/2/96/200 | |
| .vsync_len = 2, // line/2/-/34 | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_IHS | TIM2_IVS | |
| | (PIX_CLOCK_DIVIDER - 2), | |
| .cntl = CNTL_LCDTFT | CNTL_WATERMARK, | |
| .bpp = 16, | |
| }; | |
| #endif | |
| #if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343 | |
| /* Logic Product Development LCD 6.4" VGA -10 */ | |
| /* Sharp PN LQ64D343 */ | |
| /* The full horozontal cycle (Th) is clock/750/800/900. */ | |
| /* The full vertical cycle (Tv) is line/515/525/560. */ | |
| #define PIX_CLOCK_TARGET (28330000) | |
| #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) | |
| #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) | |
| static struct clcd_panel lcd_panel = { | |
| .mode = { | |
| .name = "6.4in QVGA (LQ64D343)", | |
| .xres = 640, | |
| .yres = 480, | |
| .pixclock = PIX_CLOCK, | |
| .left_margin = 32, | |
| .right_margin = 800-32-640-96, | |
| .upper_margin = 32, // line/34/34/34 | |
| .lower_margin = 540-32-480-2, | |
| .hsync_len = 96, // clk/2/96/200 | |
| .vsync_len = 2, // line/2/-/34 | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_IHS | TIM2_IVS | |
| | (PIX_CLOCK_DIVIDER - 2), | |
| .cntl = CNTL_LCDTFT | CNTL_WATERMARK, | |
| .bpp = 16, | |
| }; | |
| #endif | |
| #if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368 | |
| /* Logic Product Development LCD 10.4" VGA -10 */ | |
| /* Sharp PN LQ10D368 */ | |
| #define PIX_CLOCK_TARGET (28330000) | |
| #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) | |
| #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) | |
| static struct clcd_panel lcd_panel = { | |
| .mode = { | |
| .name = "10.4in VGA (LQ10D368)", | |
| .xres = 640, | |
| .yres = 480, | |
| .pixclock = PIX_CLOCK, | |
| .left_margin = 21, | |
| .right_margin = 15, | |
| .upper_margin = 34, | |
| .lower_margin = 5, | |
| .hsync_len = 96, | |
| .vsync_len = 16, | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_IHS | TIM2_IVS | |
| | (PIX_CLOCK_DIVIDER - 2), | |
| .cntl = CNTL_LCDTFT | CNTL_WATERMARK, | |
| .bpp = 16, | |
| }; | |
| #endif | |
| #if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41 | |
| /* Logic Product Development LCD 12.1" SVGA -10 */ | |
| /* Sharp PN LQ121S1DG41, was LQ121S1DG31 */ | |
| /* Note that with a 99993900 Hz HCLK, it is not possible to hit the | |
| * target clock frequency range of 35MHz to 42MHz. */ | |
| /* If the target pixel clock is substantially lower than the panel | |
| * spec, this is done to prevent the LCD display from glitching when | |
| * the CPU is under load. A pixel clock higher than 25MHz | |
| * (empirically determined) will compete with the CPU for bus cycles | |
| * for the Ethernet chip. However, even a pixel clock of 10MHz | |
| * competes with Compact Flash interface during some operations | |
| * (fdisk, e2fsck). And, at that speed the display may have a visible | |
| * flicker. */ | |
| /* The full horozontal cycle (Th) is clock/832/1056/1395. */ | |
| #define PIX_CLOCK_TARGET (20000000) | |
| #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) | |
| #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) | |
| static struct clcd_panel lcd_panel = { | |
| .mode = { | |
| .name = "12.1in SVGA (LQ121S1DG41)", | |
| .xres = 800, | |
| .yres = 600, | |
| .pixclock = PIX_CLOCK, | |
| .left_margin = 89, // ns/5/-/(1/PIX_CLOCK)-10 | |
| .right_margin = 1056-800-89-128, | |
| .upper_margin = 23, // line/23/23/23 | |
| .lower_margin = 44, | |
| .hsync_len = 128, // clk/2/128/200 | |
| .vsync_len = 4, // line/2/4/6 | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_IHS | TIM2_IVS | |
| | (PIX_CLOCK_DIVIDER - 2), | |
| .cntl = CNTL_LCDTFT | CNTL_WATERMARK, | |
| .bpp = 16, | |
| }; | |
| #endif | |
| #if defined CONFIG_FB_ARMCLCD_HITACHI | |
| /* Hitachi*/ | |
| /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */ | |
| #define PIX_CLOCK_TARGET (49000000) | |
| #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) | |
| #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) | |
| static struct clcd_panel lcd_panel = { | |
| .mode = { | |
| .name = "Hitachi 800x480", | |
| .xres = 800, | |
| .yres = 480, | |
| .pixclock = PIX_CLOCK, | |
| .left_margin = 88, | |
| .right_margin = 40, | |
| .upper_margin = 32, | |
| .lower_margin = 11, | |
| .hsync_len = 128, | |
| .vsync_len = 2, | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS | |
| | (PIX_CLOCK_DIVIDER - 2), | |
| .cntl = CNTL_LCDTFT | CNTL_WATERMARK, | |
| .bpp = 16, | |
| }; | |
| #endif | |
| #if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE | |
| /* AU Optotronics A070VW01 7.0 Wide Screen color Display*/ | |
| /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */ | |
| #define PIX_CLOCK_TARGET (10000000) | |
| #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) | |
| #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) | |
| static struct clcd_panel lcd_panel = { | |
| .mode = { | |
| .name = "7.0in Wide (A070VW01)", | |
| .xres = 480, | |
| .yres = 234, | |
| .pixclock = PIX_CLOCK, | |
| .left_margin = 30, | |
| .right_margin = 25, | |
| .upper_margin = 14, | |
| .lower_margin = 12, | |
| .hsync_len = 100, | |
| .vsync_len = 1, | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS | |
| | (PIX_CLOCK_DIVIDER - 2), | |
| .cntl = CNTL_LCDTFT | CNTL_WATERMARK, | |
| .bpp = 16, | |
| }; | |
| #endif | |
| #undef NS_TO_CLOCK | |
| #undef CLOCK_TO_DIV | |
| #endif /* __LCD_PANEL_H__ */ |