| # | |
| # Misc strange devices | |
| # | |
| menuconfig MISC_DEVICES | |
| bool "Misc devices" | |
| default y | |
| ---help--- | |
| Say Y here to get to see options for device drivers from various | |
| different categories. This option alone does not add any kernel code. | |
| If you say N, all options in this submenu will be skipped and disabled. | |
| if MISC_DEVICES | |
| config AD525X_DPOT | |
| tristate "Analog Devices AD525x Digital Potentiometers" | |
| depends on I2C && SYSFS | |
| help | |
| If you say yes here, you get support for the Analog Devices | |
| AD5258, AD5259, AD5251, AD5252, AD5253, AD5254 and AD5255 | |
| digital potentiometer chips. | |
| See Documentation/misc-devices/ad525x_dpot.txt for the | |
| userspace interface. | |
| This driver can also be built as a module. If so, the module | |
| will be called ad525x_dpot. | |
| config ATMEL_PWM | |
| tristate "Atmel AT32/AT91 PWM support" | |
| depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 | |
| help | |
| This option enables device driver support for the PWM channels | |
| on certain Atmel processors. Pulse Width Modulation is used for | |
| purposes including software controlled power-efficient backlights | |
| on LCD displays, motor control, and waveform generation. | |
| config ATMEL_TCLIB | |
| bool "Atmel AT32/AT91 Timer/Counter Library" | |
| depends on (AVR32 || ARCH_AT91) | |
| help | |
| Select this if you want a library to allocate the Timer/Counter | |
| blocks found on many Atmel processors. This facilitates using | |
| these blocks by different drivers despite processor differences. | |
| config ATMEL_TCB_CLKSRC | |
| bool "TC Block Clocksource" | |
| depends on ATMEL_TCLIB && GENERIC_TIME | |
| default y | |
| help | |
| Select this to get a high precision clocksource based on a | |
| TC block with a 5+ MHz base clock rate. Two timer channels | |
| are combined to make a single 32-bit timer. | |
| When GENERIC_CLOCKEVENTS is defined, the third timer channel | |
| may be used as a clock event device supporting oneshot mode | |
| (delays of up to two seconds) based on the 32 KiHz clock. | |
| config ATMEL_TCB_CLKSRC_BLOCK | |
| int | |
| depends on ATMEL_TCB_CLKSRC | |
| prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X | |
| default 0 | |
| range 0 1 | |
| help | |
| Some chips provide more than one TC block, so you have the | |
| choice of which one to use for the clock framework. The other | |
| TC can be used for other purposes, such as PWM generation and | |
| interval timing. | |
| config IBM_ASM | |
| tristate "Device driver for IBM RSA service processor" | |
| depends on X86 && PCI && INPUT && EXPERIMENTAL | |
| ---help--- | |
| This option enables device driver support for in-band access to the | |
| IBM RSA (Condor) service processor in eServer xSeries systems. | |
| The ibmasm device driver allows user space application to access | |
| ASM (Advanced Systems Management) functions on the service | |
| processor. The driver is meant to be used in conjunction with | |
| a user space API. | |
| The ibmasm driver also enables the OS to use the UART on the | |
| service processor board as a regular serial port. To make use of | |
| this feature serial driver support (CONFIG_SERIAL_8250) must be | |
| enabled. | |
| WARNING: This software may not be supported or function | |
| correctly on your IBM server. Please consult the IBM ServerProven | |
| website <http://www.pc.ibm.com/ww/eserver/xseries/serverproven> for | |
| information on the specific driver level and support statement | |
| for your IBM server. | |
| config PHANTOM | |
| tristate "Sensable PHANToM (PCI)" | |
| depends on PCI | |
| help | |
| Say Y here if you want to build a driver for Sensable PHANToM device. | |
| This driver is only for PCI PHANToMs. | |
| If you choose to build module, its name will be phantom. If unsure, | |
| say N here. | |
| config SGI_IOC4 | |
| tristate "SGI IOC4 Base IO support" | |
| depends on PCI | |
| ---help--- | |
| This option enables basic support for the IOC4 chip on certain | |
| SGI IO controller cards (IO9, IO10, and PCI-RT). This option | |
| does not enable any specific functions on such a card, but provides | |
| necessary infrastructure for other drivers to utilize. | |
| If you have an SGI Altix with an IOC4-based card say Y. | |
| Otherwise say N. | |
| config TIFM_CORE | |
| tristate "TI Flash Media interface support (EXPERIMENTAL)" | |
| depends on EXPERIMENTAL && PCI | |
| help | |
| If you want support for Texas Instruments(R) Flash Media adapters | |
| you should select this option and then also choose an appropriate | |
| host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter | |
| support', if you have a TI PCI74xx compatible card reader, for | |
| example. | |
| You will also have to select some flash card format drivers. MMC/SD | |
| cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD | |
| Interface support (MMC_TIFM_SD)'. | |
| To compile this driver as a module, choose M here: the module will | |
| be called tifm_core. | |
| config TIFM_7XX1 | |
| tristate "TI Flash Media PCI74xx/PCI76xx host adapter support (EXPERIMENTAL)" | |
| depends on PCI && TIFM_CORE && EXPERIMENTAL | |
| default TIFM_CORE | |
| help | |
| This option enables support for Texas Instruments(R) PCI74xx and | |
| PCI76xx families of Flash Media adapters, found in many laptops. | |
| To make actual use of the device, you will have to select some | |
| flash card format drivers, as outlined in the TIFM_CORE Help. | |
| To compile this driver as a module, choose M here: the module will | |
| be called tifm_7xx1. | |
| config ICS932S401 | |
| tristate "Integrated Circuits ICS932S401" | |
| depends on I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for the Integrated Circuits | |
| ICS932S401 clock control chips. | |
| This driver can also be built as a module. If so, the module | |
| will be called ics932s401. | |
| config ATMEL_SSC | |
| tristate "Device driver for Atmel SSC peripheral" | |
| depends on AVR32 || ARCH_AT91 | |
| ---help--- | |
| This option enables device driver support for Atmel Synchronized | |
| Serial Communication peripheral (SSC). | |
| The SSC peripheral supports a wide variety of serial frame based | |
| communications, i.e. I2S, SPI, etc. | |
| If unsure, say N. | |
| config ENCLOSURE_SERVICES | |
| tristate "Enclosure Services" | |
| default n | |
| help | |
| Provides support for intelligent enclosures (bays which | |
| contain storage devices). You also need either a host | |
| driver (SCSI/ATA) which supports enclosures | |
| or a SCSI enclosure device (SES) to use these services. | |
| config SGI_XP | |
| tristate "Support communication between SGI SSIs" | |
| depends on NET | |
| depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP | |
| select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2 | |
| select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2 | |
| select SGI_GRU if X86_64 && SMP | |
| ---help--- | |
| An SGI machine can be divided into multiple Single System | |
| Images which act independently of each other and have | |
| hardware based memory protection from the others. Enabling | |
| this feature will allow for direct communication between SSIs | |
| based on a network adapter and DMA messaging. | |
| config CS5535_MFGPT | |
| tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support" | |
| depends on PCI | |
| depends on X86 | |
| default n | |
| help | |
| This driver provides access to MFGPT functionality for other | |
| drivers that need timers. MFGPTs are available in the CS5535 and | |
| CS5536 companion chips that are found in AMD Geode and several | |
| other platforms. They have a better resolution and max interval | |
| than the generic PIT, and are suitable for use as high-res timers. | |
| You probably don't want to enable this manually; other drivers that | |
| make use of it should enable it. | |
| config CS5535_MFGPT_DEFAULT_IRQ | |
| int | |
| depends on CS5535_MFGPT | |
| default 7 | |
| help | |
| MFGPTs on the CS5535 require an interrupt. The selected IRQ | |
| can be overridden as a module option as well as by driver that | |
| use the cs5535_mfgpt_ API; however, different architectures might | |
| want to use a different IRQ by default. This is here for | |
| architectures to set as necessary. | |
| config CS5535_CLOCK_EVENT_SRC | |
| tristate "CS5535/CS5536 high-res timer (MFGPT) events" | |
| depends on GENERIC_TIME && GENERIC_CLOCKEVENTS && CS5535_MFGPT | |
| help | |
| This driver provides a clock event source based on the MFGPT | |
| timer(s) in the CS5535 and CS5536 companion chips. | |
| MFGPTs have a better resolution and max interval than the | |
| generic PIT, and are suitable for use as high-res timers. | |
| config HP_ILO | |
| tristate "Channel interface driver for HP iLO/iLO2 processor" | |
| depends on PCI | |
| default n | |
| help | |
| The channel interface driver allows applications to communicate | |
| with iLO/iLO2 management processors present on HP ProLiant | |
| servers. Upon loading, the driver creates /dev/hpilo/dXccbN files, | |
| which can be used to gather data from the management processor, | |
| via read and write system calls. | |
| To compile this driver as a module, choose M here: the | |
| module will be called hpilo. | |
| config SGI_GRU | |
| tristate "SGI GRU driver" | |
| depends on X86_UV && SMP | |
| default n | |
| select MMU_NOTIFIER | |
| ---help--- | |
| The GRU is a hardware resource located in the system chipset. The GRU | |
| contains memory that can be mmapped into the user address space. This memory is | |
| used to communicate with the GRU to perform functions such as load/store, | |
| scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user | |
| instructions using user virtual addresses. GRU instructions (ex., bcopy) use | |
| user virtual addresses for operands. | |
| If you are not running on a SGI UV system, say N. | |
| config SGI_GRU_DEBUG | |
| bool "SGI GRU driver debug" | |
| depends on SGI_GRU | |
| default n | |
| ---help--- | |
| This option enables addition debugging code for the SGI GRU driver. If | |
| you are unsure, say N. | |
| config ISL29003 | |
| tristate "Intersil ISL29003 ambient light sensor" | |
| depends on I2C && SYSFS | |
| help | |
| If you say yes here you get support for the Intersil ISL29003 | |
| ambient light sensor. | |
| This driver can also be built as a module. If so, the module | |
| will be called isl29003. | |
| config SENSORS_TSL2550 | |
| tristate "Taos TSL2550 ambient light sensor" | |
| depends on I2C && SYSFS | |
| help | |
| If you say yes here you get support for the Taos TSL2550 | |
| ambient light sensor. | |
| This driver can also be built as a module. If so, the module | |
| will be called tsl2550. | |
| config EP93XX_PWM | |
| tristate "EP93xx PWM support" | |
| depends on ARCH_EP93XX | |
| help | |
| This option enables device driver support for the PWM channels | |
| on the Cirrus EP93xx processors. The EP9307 chip only has one | |
| PWM channel all the others have two, the second channel is an | |
| alternate function of the EGPIO14 pin. A sysfs interface is | |
| provided to control the PWM channels. | |
| To compile this driver as a module, choose M here: the module will | |
| be called ep93xx_pwm. | |
| config DS1682 | |
| tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm" | |
| depends on I2C && EXPERIMENTAL | |
| help | |
| If you say yes here you get support for Dallas Semiconductor | |
| DS1682 Total Elapsed Time Recorder. | |
| This driver can also be built as a module. If so, the module | |
| will be called ds1682. | |
| config TI_DAC7512 | |
| tristate "Texas Instruments DAC7512" | |
| depends on SPI && SYSFS | |
| help | |
| If you say yes here you get support for the Texas Instruments | |
| DAC7512 16-bit digital-to-analog converter. | |
| This driver can also be built as a module. If so, the module | |
| will be calles ti_dac7512. | |
| source "drivers/misc/c2port/Kconfig" | |
| source "drivers/misc/eeprom/Kconfig" | |
| source "drivers/misc/cb710/Kconfig" | |
| source "drivers/misc/iwmc3200top/Kconfig" | |
| endif # MISC_DEVICES |