| config MAC80211 | |
| tristate "Generic IEEE 802.11 Networking Stack (mac80211)" | |
| select CRYPTO | |
| select CRYPTO_ECB | |
| select CRYPTO_ARC4 | |
| select CRYPTO_AES | |
| select CRC32 | |
| select WIRELESS_EXT | |
| select CFG80211 | |
| ---help--- | |
| This option enables the hardware independent IEEE 802.11 | |
| networking stack. | |
| config MAC80211_QOS | |
| def_bool y | |
| depends on MAC80211 | |
| depends on NET_SCHED | |
| depends on NETDEVICES_MULTIQUEUE | |
| comment "QoS/HT support disabled" | |
| depends on MAC80211 && !MAC80211_QOS | |
| comment "QoS/HT support needs CONFIG_NET_SCHED" | |
| depends on MAC80211 && !NET_SCHED | |
| comment "QoS/HT support needs CONFIG_NETDEVICES_MULTIQUEUE" | |
| depends on MAC80211 && !NETDEVICES_MULTIQUEUE | |
| menu "Rate control algorithm selection" | |
| depends on MAC80211 != n | |
| choice | |
| prompt "Default rate control algorithm" | |
| default MAC80211_RC_DEFAULT_PID | |
| ---help--- | |
| This option selects the default rate control algorithm | |
| mac80211 will use. Note that this default can still be | |
| overriden through the ieee80211_default_rc_algo module | |
| parameter if different algorithms are available. | |
| config MAC80211_RC_DEFAULT_PID | |
| bool "PID controller based rate control algorithm" | |
| select MAC80211_RC_PID | |
| ---help--- | |
| Select the PID controller based rate control as the | |
| default rate control algorithm. You should choose | |
| this unless you know what you are doing. | |
| config MAC80211_RC_DEFAULT_NONE | |
| bool "No default algorithm" | |
| depends on EMBEDDED | |
| help | |
| Selecting this option will select no default algorithm | |
| and allow you to not build any. Do not choose this | |
| option unless you know your driver comes with another | |
| suitable algorithm. | |
| endchoice | |
| comment "Selecting 'y' for an algorithm will" | |
| comment "build the algorithm into mac80211." | |
| config MAC80211_RC_DEFAULT | |
| string | |
| default "pid" if MAC80211_RC_DEFAULT_PID | |
| default "" | |
| config MAC80211_RC_PID | |
| tristate "PID controller based rate control algorithm" | |
| ---help--- | |
| This option enables a TX rate control algorithm for | |
| mac80211 that uses a PID controller to select the TX | |
| rate. | |
| Say Y or M unless you're sure you want to use a | |
| different rate control algorithm. | |
| endmenu | |
| config MAC80211_MESH | |
| bool "Enable mac80211 mesh networking (pre-802.11s) support" | |
| depends on MAC80211 && EXPERIMENTAL | |
| ---help--- | |
| This options enables support of Draft 802.11s mesh networking. | |
| The implementation is based on Draft 1.08 of the Mesh Networking | |
| amendment. For more information visit http://o11s.org/. | |
| config MAC80211_LEDS | |
| bool "Enable LED triggers" | |
| depends on MAC80211 | |
| select NEW_LEDS | |
| select LEDS_TRIGGERS | |
| ---help--- | |
| This option enables a few LED triggers for different | |
| packet receive/transmit events. | |
| config MAC80211_DEBUGFS | |
| bool "Export mac80211 internals in DebugFS" | |
| depends on MAC80211 && DEBUG_FS | |
| ---help--- | |
| Select this to see extensive information about | |
| the internal state of mac80211 in debugfs. | |
| Say N unless you know you need this. | |
| config MAC80211_DEBUG_PACKET_ALIGNMENT | |
| bool "Enable packet alignment debugging" | |
| depends on MAC80211 | |
| help | |
| This option is recommended for driver authors and strongly | |
| discouraged for everybody else, it will trigger a warning | |
| when a driver hands mac80211 a buffer that is aligned in | |
| a way that will cause problems with the IP stack on some | |
| architectures. | |
| Say N unless you're writing a mac80211 based driver. | |
| config MAC80211_DEBUG | |
| bool "Enable debugging output" | |
| depends on MAC80211 | |
| ---help--- | |
| This option will enable debug tracing output for the | |
| ieee80211 network stack. | |
| If you are not trying to debug or develop the ieee80211 | |
| subsystem, you most likely want to say N here. | |
| config MAC80211_HT_DEBUG | |
| bool "Enable HT debugging output" | |
| depends on MAC80211_DEBUG | |
| ---help--- | |
| This option enables 802.11n High Throughput features | |
| debug tracing output. | |
| If you are not trying to debug of develop the ieee80211 | |
| subsystem, you most likely want to say N here. | |
| config MAC80211_VERBOSE_DEBUG | |
| bool "Verbose debugging output" | |
| depends on MAC80211_DEBUG | |
| config MAC80211_LOWTX_FRAME_DUMP | |
| bool "Debug frame dumping" | |
| depends on MAC80211_DEBUG | |
| ---help--- | |
| Selecting this option will cause the stack to | |
| print a message for each frame that is handed | |
| to the lowlevel driver for transmission. This | |
| message includes all MAC addresses and the | |
| frame control field. | |
| If unsure, say N and insert the debugging code | |
| you require into the driver you are debugging. | |
| config TKIP_DEBUG | |
| bool "TKIP debugging" | |
| depends on MAC80211_DEBUG | |
| config MAC80211_DEBUG_COUNTERS | |
| bool "Extra statistics for TX/RX debugging" | |
| depends on MAC80211_DEBUG | |
| config MAC80211_IBSS_DEBUG | |
| bool "Support for IBSS testing" | |
| depends on MAC80211_DEBUG | |
| ---help--- | |
| Say Y here if you intend to debug the IBSS code. | |
| config MAC80211_VERBOSE_PS_DEBUG | |
| bool "Verbose powersave mode debugging" | |
| depends on MAC80211_DEBUG | |
| ---help--- | |
| Say Y here to print out verbose powersave | |
| mode debug messages. | |
| config MAC80211_VERBOSE_MPL_DEBUG | |
| bool "Verbose mesh peer link debugging" | |
| depends on MAC80211_DEBUG && MAC80211_MESH | |
| ---help--- | |
| Say Y here to print out verbose mesh peer link | |
| debug messages. |