| /**************************************************************************** | |
| * Driver for Solarflare Solarstorm network controllers and boards | |
| * Copyright 2007 Solarflare Communications Inc. | |
| * | |
| * This program is free software; you can redistribute it and/or modify it | |
| * under the terms of the GNU General Public License version 2 as published | |
| * by the Free Software Foundation, incorporated herein by reference. | |
| */ | |
| /***************************************************************************** | |
| * Support for the SFE4001 NIC: driver code for the PCA9539 I/O expander that | |
| * controls the PHY power rails, and for the MAX6647 temp. sensor used to check | |
| * the PHY | |
| */ | |
| #include <linux/delay.h> | |
| #include "efx.h" | |
| #include "phy.h" | |
| #include "boards.h" | |
| #include "falcon.h" | |
| #include "falcon_hwdefs.h" | |
| #include "mac.h" | |
| /************************************************************************** | |
| * | |
| * I2C IO Expander device | |
| * | |
| **************************************************************************/ | |
| #define PCA9539 0x74 | |
| #define P0_IN 0x00 | |
| #define P0_OUT 0x02 | |
| #define P0_INVERT 0x04 | |
| #define P0_CONFIG 0x06 | |
| #define P0_EN_1V0X_LBN 0 | |
| #define P0_EN_1V0X_WIDTH 1 | |
| #define P0_EN_1V2_LBN 1 | |
| #define P0_EN_1V2_WIDTH 1 | |
| #define P0_EN_2V5_LBN 2 | |
| #define P0_EN_2V5_WIDTH 1 | |
| #define P0_EN_3V3X_LBN 3 | |
| #define P0_EN_3V3X_WIDTH 1 | |
| #define P0_EN_5V_LBN 4 | |
| #define P0_EN_5V_WIDTH 1 | |
| #define P0_SHORTEN_JTAG_LBN 5 | |
| #define P0_SHORTEN_JTAG_WIDTH 1 | |
| #define P0_X_TRST_LBN 6 | |
| #define P0_X_TRST_WIDTH 1 | |
| #define P0_DSP_RESET_LBN 7 | |
| #define P0_DSP_RESET_WIDTH 1 | |
| #define P1_IN 0x01 | |
| #define P1_OUT 0x03 | |
| #define P1_INVERT 0x05 | |
| #define P1_CONFIG 0x07 | |
| #define P1_AFE_PWD_LBN 0 | |
| #define P1_AFE_PWD_WIDTH 1 | |
| #define P1_DSP_PWD25_LBN 1 | |
| #define P1_DSP_PWD25_WIDTH 1 | |
| #define P1_RESERVED_LBN 2 | |
| #define P1_RESERVED_WIDTH 2 | |
| #define P1_SPARE_LBN 4 | |
| #define P1_SPARE_WIDTH 4 | |
| /************************************************************************** | |
| * | |
| * Temperature Sensor | |
| * | |
| **************************************************************************/ | |
| #define MAX6647 0x4e | |
| #define RLTS 0x00 | |
| #define RLTE 0x01 | |
| #define RSL 0x02 | |
| #define RCL 0x03 | |
| #define RCRA 0x04 | |
| #define RLHN 0x05 | |
| #define RLLI 0x06 | |
| #define RRHI 0x07 | |
| #define RRLS 0x08 | |
| #define WCRW 0x0a | |
| #define WLHO 0x0b | |
| #define WRHA 0x0c | |
| #define WRLN 0x0e | |
| #define OSHT 0x0f | |
| #define REET 0x10 | |
| #define RIET 0x11 | |
| #define RWOE 0x19 | |
| #define RWOI 0x20 | |
| #define HYS 0x21 | |
| #define QUEUE 0x22 | |
| #define MFID 0xfe | |
| #define REVID 0xff | |
| /* Status bits */ | |
| #define MAX6647_BUSY (1 << 7) /* ADC is converting */ | |
| #define MAX6647_LHIGH (1 << 6) /* Local high temp. alarm */ | |
| #define MAX6647_LLOW (1 << 5) /* Local low temp. alarm */ | |
| #define MAX6647_RHIGH (1 << 4) /* Remote high temp. alarm */ | |
| #define MAX6647_RLOW (1 << 3) /* Remote low temp. alarm */ | |
| #define MAX6647_FAULT (1 << 2) /* DXN/DXP short/open circuit */ | |
| #define MAX6647_EOT (1 << 1) /* Remote junction overtemp. */ | |
| #define MAX6647_IOT (1 << 0) /* Local junction overtemp. */ | |
| static const u8 xgphy_max_temperature = 90; | |
| static void sfe4001_poweroff(struct efx_nic *efx) | |
| { | |
| struct i2c_client *ioexp_client = efx->board_info.ioexp_client; | |
| struct i2c_client *hwmon_client = efx->board_info.hwmon_client; | |
| /* Turn off all power rails and disable outputs */ | |
| i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff); | |
| i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff); | |
| i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff); | |
| /* Clear any over-temperature alert */ | |
| i2c_smbus_read_byte_data(hwmon_client, RSL); | |
| } | |
| static void sfe4001_fini(struct efx_nic *efx) | |
| { | |
| EFX_INFO(efx, "%s\n", __func__); | |
| sfe4001_poweroff(efx); | |
| i2c_unregister_device(efx->board_info.ioexp_client); | |
| i2c_unregister_device(efx->board_info.hwmon_client); | |
| } | |
| /* The P0_EN_3V3X line on SFE4001 boards (from A2 onward) is connected | |
| * to the FLASH_CFG_1 input on the DSP. We must keep it high at power- | |
| * up to allow writing the flash (done through MDIO from userland). | |
| */ | |
| unsigned int sfe4001_phy_flash_cfg; | |
| module_param_named(phy_flash_cfg, sfe4001_phy_flash_cfg, uint, 0444); | |
| MODULE_PARM_DESC(phy_flash_cfg, | |
| "Force PHY to enter flash configuration mode"); | |
| /* This board uses an I2C expander to provider power to the PHY, which needs to | |
| * be turned on before the PHY can be used. | |
| * Context: Process context, rtnl lock held | |
| */ | |
| int sfe4001_init(struct efx_nic *efx) | |
| { | |
| struct i2c_client *hwmon_client, *ioexp_client; | |
| unsigned int count; | |
| int rc; | |
| u8 out; | |
| efx_dword_t reg; | |
| hwmon_client = i2c_new_dummy(&efx->i2c_adap, MAX6647); | |
| if (!hwmon_client) | |
| return -EIO; | |
| efx->board_info.hwmon_client = hwmon_client; | |
| ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539); | |
| if (!ioexp_client) { | |
| rc = -EIO; | |
| goto fail_hwmon; | |
| } | |
| efx->board_info.ioexp_client = ioexp_client; | |
| /* 10Xpress has fixed-function LED pins, so there is no board-specific | |
| * blink code. */ | |
| efx->board_info.blink = tenxpress_phy_blink; | |
| /* Ensure that XGXS and XAUI SerDes are held in reset */ | |
| EFX_POPULATE_DWORD_7(reg, XX_PWRDNA_EN, 1, | |
| XX_PWRDNB_EN, 1, | |
| XX_RSTPLLAB_EN, 1, | |
| XX_RESETA_EN, 1, | |
| XX_RESETB_EN, 1, | |
| XX_RSTXGXSRX_EN, 1, | |
| XX_RSTXGXSTX_EN, 1); | |
| falcon_xmac_writel(efx, ®, XX_PWR_RST_REG_MAC); | |
| udelay(10); | |
| efx->board_info.fini = sfe4001_fini; | |
| /* Set DSP over-temperature alert threshold */ | |
| EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature); | |
| rc = i2c_smbus_write_byte_data(hwmon_client, WLHO, | |
| xgphy_max_temperature); | |
| if (rc) | |
| goto fail_ioexp; | |
| /* Read it back and verify */ | |
| rc = i2c_smbus_read_byte_data(hwmon_client, RLHN); | |
| if (rc < 0) | |
| goto fail_ioexp; | |
| if (rc != xgphy_max_temperature) { | |
| rc = -EFAULT; | |
| goto fail_ioexp; | |
| } | |
| /* Clear any previous over-temperature alert */ | |
| rc = i2c_smbus_read_byte_data(hwmon_client, RSL); | |
| if (rc < 0) | |
| goto fail_ioexp; | |
| /* Enable port 0 and port 1 outputs on IO expander */ | |
| rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00); | |
| if (rc) | |
| goto fail_ioexp; | |
| rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, | |
| 0xff & ~(1 << P1_SPARE_LBN)); | |
| if (rc) | |
| goto fail_on; | |
| /* Turn all power off then wait 1 sec. This ensures PHY is reset */ | |
| out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) | | |
| (0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) | | |
| (0 << P0_EN_1V0X_LBN)); | |
| rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out); | |
| if (rc) | |
| goto fail_on; | |
| schedule_timeout_uninterruptible(HZ); | |
| count = 0; | |
| do { | |
| /* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */ | |
| out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) | | |
| (1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) | | |
| (1 << P0_X_TRST_LBN)); | |
| if (sfe4001_phy_flash_cfg) | |
| out |= 1 << P0_EN_3V3X_LBN; | |
| rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out); | |
| if (rc) | |
| goto fail_on; | |
| msleep(10); | |
| /* Turn on 1V power rail */ | |
| out &= ~(1 << P0_EN_1V0X_LBN); | |
| rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out); | |
| if (rc) | |
| goto fail_on; | |
| EFX_INFO(efx, "waiting for power (attempt %d)...\n", count); | |
| schedule_timeout_uninterruptible(HZ); | |
| /* Check DSP is powered */ | |
| rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN); | |
| if (rc < 0) | |
| goto fail_on; | |
| if (rc & (1 << P1_AFE_PWD_LBN)) | |
| goto done; | |
| /* DSP doesn't look powered in flash config mode */ | |
| if (sfe4001_phy_flash_cfg) | |
| goto done; | |
| } while (++count < 20); | |
| EFX_INFO(efx, "timed out waiting for power\n"); | |
| rc = -ETIMEDOUT; | |
| goto fail_on; | |
| done: | |
| EFX_INFO(efx, "PHY is powered on\n"); | |
| return 0; | |
| fail_on: | |
| sfe4001_poweroff(efx); | |
| fail_ioexp: | |
| i2c_unregister_device(ioexp_client); | |
| fail_hwmon: | |
| i2c_unregister_device(hwmon_client); | |
| return rc; | |
| } |