| /******************************************************************************* | |
| Intel PRO/1000 Linux driver | |
| Copyright(c) 1999 - 2008 Intel Corporation. | |
| This program is free software; you can redistribute it and/or modify it | |
| under the terms and conditions of the GNU General Public License, | |
| version 2, as published by the Free Software Foundation. | |
| This program is distributed in the hope it will be useful, but WITHOUT | |
| ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or | |
| FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for | |
| more details. | |
| You should have received a copy of the GNU General Public License along with | |
| this program; if not, write to the Free Software Foundation, Inc., | |
| 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. | |
| The full GNU General Public License is included in this distribution in | |
| the file called "COPYING". | |
| Contact Information: | |
| Linux NICS <linux.nics@intel.com> | |
| e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> | |
| Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 | |
| *******************************************************************************/ | |
| /* | |
| * 82562G-2 10/100 Network Connection | |
| * 82562GT 10/100 Network Connection | |
| * 82562GT-2 10/100 Network Connection | |
| * 82562V 10/100 Network Connection | |
| * 82562V-2 10/100 Network Connection | |
| * 82566DC-2 Gigabit Network Connection | |
| * 82566DC Gigabit Network Connection | |
| * 82566DM-2 Gigabit Network Connection | |
| * 82566DM Gigabit Network Connection | |
| * 82566MC Gigabit Network Connection | |
| * 82566MM Gigabit Network Connection | |
| * 82567LM Gigabit Network Connection | |
| * 82567LF Gigabit Network Connection | |
| * 82567LM-2 Gigabit Network Connection | |
| * 82567LF-2 Gigabit Network Connection | |
| * 82567V-2 Gigabit Network Connection | |
| * 82562GT-3 10/100 Network Connection | |
| */ | |
| #include <linux/netdevice.h> | |
| #include <linux/ethtool.h> | |
| #include <linux/delay.h> | |
| #include <linux/pci.h> | |
| #include "e1000.h" | |
| #define ICH_FLASH_GFPREG 0x0000 | |
| #define ICH_FLASH_HSFSTS 0x0004 | |
| #define ICH_FLASH_HSFCTL 0x0006 | |
| #define ICH_FLASH_FADDR 0x0008 | |
| #define ICH_FLASH_FDATA0 0x0010 | |
| #define ICH_FLASH_READ_COMMAND_TIMEOUT 500 | |
| #define ICH_FLASH_WRITE_COMMAND_TIMEOUT 500 | |
| #define ICH_FLASH_ERASE_COMMAND_TIMEOUT 3000000 | |
| #define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF | |
| #define ICH_FLASH_CYCLE_REPEAT_COUNT 10 | |
| #define ICH_CYCLE_READ 0 | |
| #define ICH_CYCLE_WRITE 2 | |
| #define ICH_CYCLE_ERASE 3 | |
| #define FLASH_GFPREG_BASE_MASK 0x1FFF | |
| #define FLASH_SECTOR_ADDR_SHIFT 12 | |
| #define ICH_FLASH_SEG_SIZE_256 256 | |
| #define ICH_FLASH_SEG_SIZE_4K 4096 | |
| #define ICH_FLASH_SEG_SIZE_8K 8192 | |
| #define ICH_FLASH_SEG_SIZE_64K 65536 | |
| #define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */ | |
| #define E1000_ICH_MNG_IAMT_MODE 0x2 | |
| #define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ | |
| (ID_LED_DEF1_OFF2 << 8) | \ | |
| (ID_LED_DEF1_ON2 << 4) | \ | |
| (ID_LED_DEF1_DEF2)) | |
| #define E1000_ICH_NVM_SIG_WORD 0x13 | |
| #define E1000_ICH_NVM_SIG_MASK 0xC000 | |
| #define E1000_ICH8_LAN_INIT_TIMEOUT 1500 | |
| #define E1000_FEXTNVM_SW_CONFIG 1 | |
| #define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M :/ */ | |
| #define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL | |
| #define E1000_ICH_RAR_ENTRIES 7 | |
| #define PHY_PAGE_SHIFT 5 | |
| #define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \ | |
| ((reg) & MAX_PHY_REG_ADDRESS)) | |
| #define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */ | |
| #define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */ | |
| #define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 | |
| #define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300 | |
| #define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200 | |
| /* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ | |
| /* Offset 04h HSFSTS */ | |
| union ich8_hws_flash_status { | |
| struct ich8_hsfsts { | |
| u16 flcdone :1; /* bit 0 Flash Cycle Done */ | |
| u16 flcerr :1; /* bit 1 Flash Cycle Error */ | |
| u16 dael :1; /* bit 2 Direct Access error Log */ | |
| u16 berasesz :2; /* bit 4:3 Sector Erase Size */ | |
| u16 flcinprog :1; /* bit 5 flash cycle in Progress */ | |
| u16 reserved1 :2; /* bit 13:6 Reserved */ | |
| u16 reserved2 :6; /* bit 13:6 Reserved */ | |
| u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */ | |
| u16 flockdn :1; /* bit 15 Flash Config Lock-Down */ | |
| } hsf_status; | |
| u16 regval; | |
| }; | |
| /* ICH GbE Flash Hardware Sequencing Flash control Register bit breakdown */ | |
| /* Offset 06h FLCTL */ | |
| union ich8_hws_flash_ctrl { | |
| struct ich8_hsflctl { | |
| u16 flcgo :1; /* 0 Flash Cycle Go */ | |
| u16 flcycle :2; /* 2:1 Flash Cycle */ | |
| u16 reserved :5; /* 7:3 Reserved */ | |
| u16 fldbcount :2; /* 9:8 Flash Data Byte Count */ | |
| u16 flockdn :6; /* 15:10 Reserved */ | |
| } hsf_ctrl; | |
| u16 regval; | |
| }; | |
| /* ICH Flash Region Access Permissions */ | |
| union ich8_hws_flash_regacc { | |
| struct ich8_flracc { | |
| u32 grra :8; /* 0:7 GbE region Read Access */ | |
| u32 grwa :8; /* 8:15 GbE region Write Access */ | |
| u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */ | |
| u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */ | |
| } hsf_flregacc; | |
| u16 regval; | |
| }; | |
| static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw); | |
| static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw); | |
| static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw); | |
| static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw); | |
| static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank); | |
| static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, | |
| u32 offset, u8 byte); | |
| static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, | |
| u16 *data); | |
| static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, | |
| u8 size, u16 *data); | |
| static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw); | |
| static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw); | |
| static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg) | |
| { | |
| return readw(hw->flash_address + reg); | |
| } | |
| static inline u32 __er32flash(struct e1000_hw *hw, unsigned long reg) | |
| { | |
| return readl(hw->flash_address + reg); | |
| } | |
| static inline void __ew16flash(struct e1000_hw *hw, unsigned long reg, u16 val) | |
| { | |
| writew(val, hw->flash_address + reg); | |
| } | |
| static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val) | |
| { | |
| writel(val, hw->flash_address + reg); | |
| } | |
| #define er16flash(reg) __er16flash(hw, (reg)) | |
| #define er32flash(reg) __er32flash(hw, (reg)) | |
| #define ew16flash(reg,val) __ew16flash(hw, (reg), (val)) | |
| #define ew32flash(reg,val) __ew32flash(hw, (reg), (val)) | |
| /** | |
| * e1000_init_phy_params_ich8lan - Initialize PHY function pointers | |
| * @hw: pointer to the HW structure | |
| * | |
| * Initialize family-specific PHY parameters and function pointers. | |
| **/ | |
| static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_phy_info *phy = &hw->phy; | |
| s32 ret_val; | |
| u16 i = 0; | |
| phy->addr = 1; | |
| phy->reset_delay_us = 100; | |
| /* | |
| * We may need to do this twice - once for IGP and if that fails, | |
| * we'll set BM func pointers and try again | |
| */ | |
| ret_val = e1000e_determine_phy_address(hw); | |
| if (ret_val) { | |
| hw->phy.ops.write_phy_reg = e1000e_write_phy_reg_bm; | |
| hw->phy.ops.read_phy_reg = e1000e_read_phy_reg_bm; | |
| ret_val = e1000e_determine_phy_address(hw); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| phy->id = 0; | |
| while ((e1000_phy_unknown == e1000e_get_phy_type_from_id(phy->id)) && | |
| (i++ < 100)) { | |
| msleep(1); | |
| ret_val = e1000e_get_phy_id(hw); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| /* Verify phy id */ | |
| switch (phy->id) { | |
| case IGP03E1000_E_PHY_ID: | |
| phy->type = e1000_phy_igp_3; | |
| phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; | |
| break; | |
| case IFE_E_PHY_ID: | |
| case IFE_PLUS_E_PHY_ID: | |
| case IFE_C_E_PHY_ID: | |
| phy->type = e1000_phy_ife; | |
| phy->autoneg_mask = E1000_ALL_NOT_GIG; | |
| break; | |
| case BME1000_E_PHY_ID: | |
| phy->type = e1000_phy_bm; | |
| phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; | |
| hw->phy.ops.read_phy_reg = e1000e_read_phy_reg_bm; | |
| hw->phy.ops.write_phy_reg = e1000e_write_phy_reg_bm; | |
| hw->phy.ops.commit_phy = e1000e_phy_sw_reset; | |
| break; | |
| default: | |
| return -E1000_ERR_PHY; | |
| break; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * e1000_init_nvm_params_ich8lan - Initialize NVM function pointers | |
| * @hw: pointer to the HW structure | |
| * | |
| * Initialize family-specific NVM parameters and function | |
| * pointers. | |
| **/ | |
| static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_nvm_info *nvm = &hw->nvm; | |
| struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; | |
| u32 gfpreg; | |
| u32 sector_base_addr; | |
| u32 sector_end_addr; | |
| u16 i; | |
| /* Can't read flash registers if the register set isn't mapped. */ | |
| if (!hw->flash_address) { | |
| hw_dbg(hw, "ERROR: Flash registers not mapped\n"); | |
| return -E1000_ERR_CONFIG; | |
| } | |
| nvm->type = e1000_nvm_flash_sw; | |
| gfpreg = er32flash(ICH_FLASH_GFPREG); | |
| /* | |
| * sector_X_addr is a "sector"-aligned address (4096 bytes) | |
| * Add 1 to sector_end_addr since this sector is included in | |
| * the overall size. | |
| */ | |
| sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK; | |
| sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1; | |
| /* flash_base_addr is byte-aligned */ | |
| nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT; | |
| /* | |
| * find total size of the NVM, then cut in half since the total | |
| * size represents two separate NVM banks. | |
| */ | |
| nvm->flash_bank_size = (sector_end_addr - sector_base_addr) | |
| << FLASH_SECTOR_ADDR_SHIFT; | |
| nvm->flash_bank_size /= 2; | |
| /* Adjust to word count */ | |
| nvm->flash_bank_size /= sizeof(u16); | |
| nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS; | |
| /* Clear shadow ram */ | |
| for (i = 0; i < nvm->word_size; i++) { | |
| dev_spec->shadow_ram[i].modified = 0; | |
| dev_spec->shadow_ram[i].value = 0xFFFF; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * e1000_init_mac_params_ich8lan - Initialize MAC function pointers | |
| * @hw: pointer to the HW structure | |
| * | |
| * Initialize family-specific MAC parameters and function | |
| * pointers. | |
| **/ | |
| static s32 e1000_init_mac_params_ich8lan(struct e1000_adapter *adapter) | |
| { | |
| struct e1000_hw *hw = &adapter->hw; | |
| struct e1000_mac_info *mac = &hw->mac; | |
| /* Set media type function pointer */ | |
| hw->phy.media_type = e1000_media_type_copper; | |
| /* Set mta register count */ | |
| mac->mta_reg_count = 32; | |
| /* Set rar entry count */ | |
| mac->rar_entry_count = E1000_ICH_RAR_ENTRIES; | |
| if (mac->type == e1000_ich8lan) | |
| mac->rar_entry_count--; | |
| /* Set if manageability features are enabled. */ | |
| mac->arc_subsystem_valid = 1; | |
| /* Enable PCS Lock-loss workaround for ICH8 */ | |
| if (mac->type == e1000_ich8lan) | |
| e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw, 1); | |
| return 0; | |
| } | |
| static s32 e1000_get_variants_ich8lan(struct e1000_adapter *adapter) | |
| { | |
| struct e1000_hw *hw = &adapter->hw; | |
| s32 rc; | |
| rc = e1000_init_mac_params_ich8lan(adapter); | |
| if (rc) | |
| return rc; | |
| rc = e1000_init_nvm_params_ich8lan(hw); | |
| if (rc) | |
| return rc; | |
| rc = e1000_init_phy_params_ich8lan(hw); | |
| if (rc) | |
| return rc; | |
| if ((adapter->hw.mac.type == e1000_ich8lan) && | |
| (adapter->hw.phy.type == e1000_phy_igp_3)) | |
| adapter->flags |= FLAG_LSC_GIG_SPEED_DROP; | |
| return 0; | |
| } | |
| /** | |
| * e1000_acquire_swflag_ich8lan - Acquire software control flag | |
| * @hw: pointer to the HW structure | |
| * | |
| * Acquires the software control flag for performing NVM and PHY | |
| * operations. This is a function pointer entry point only called by | |
| * read/write routines for the PHY and NVM parts. | |
| **/ | |
| static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 extcnf_ctrl; | |
| u32 timeout = PHY_CFG_TIMEOUT; | |
| while (timeout) { | |
| extcnf_ctrl = er32(EXTCNF_CTRL); | |
| extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; | |
| ew32(EXTCNF_CTRL, extcnf_ctrl); | |
| extcnf_ctrl = er32(EXTCNF_CTRL); | |
| if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) | |
| break; | |
| mdelay(1); | |
| timeout--; | |
| } | |
| if (!timeout) { | |
| hw_dbg(hw, "FW or HW has locked the resource for too long.\n"); | |
| return -E1000_ERR_CONFIG; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * e1000_release_swflag_ich8lan - Release software control flag | |
| * @hw: pointer to the HW structure | |
| * | |
| * Releases the software control flag for performing NVM and PHY operations. | |
| * This is a function pointer entry point only called by read/write | |
| * routines for the PHY and NVM parts. | |
| **/ | |
| static void e1000_release_swflag_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 extcnf_ctrl; | |
| extcnf_ctrl = er32(EXTCNF_CTRL); | |
| extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; | |
| ew32(EXTCNF_CTRL, extcnf_ctrl); | |
| } | |
| /** | |
| * e1000_check_reset_block_ich8lan - Check if PHY reset is blocked | |
| * @hw: pointer to the HW structure | |
| * | |
| * Checks if firmware is blocking the reset of the PHY. | |
| * This is a function pointer entry point only called by | |
| * reset routines. | |
| **/ | |
| static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 fwsm; | |
| fwsm = er32(FWSM); | |
| return (fwsm & E1000_ICH_FWSM_RSPCIPHY) ? 0 : E1000_BLK_PHY_RESET; | |
| } | |
| /** | |
| * e1000_phy_force_speed_duplex_ich8lan - Force PHY speed & duplex | |
| * @hw: pointer to the HW structure | |
| * | |
| * Forces the speed and duplex settings of the PHY. | |
| * This is a function pointer entry point only called by | |
| * PHY setup routines. | |
| **/ | |
| static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_phy_info *phy = &hw->phy; | |
| s32 ret_val; | |
| u16 data; | |
| bool link; | |
| if (phy->type != e1000_phy_ife) { | |
| ret_val = e1000e_phy_force_speed_duplex_igp(hw); | |
| return ret_val; | |
| } | |
| ret_val = e1e_rphy(hw, PHY_CONTROL, &data); | |
| if (ret_val) | |
| return ret_val; | |
| e1000e_phy_force_speed_duplex_setup(hw, &data); | |
| ret_val = e1e_wphy(hw, PHY_CONTROL, data); | |
| if (ret_val) | |
| return ret_val; | |
| /* Disable MDI-X support for 10/100 */ | |
| ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); | |
| if (ret_val) | |
| return ret_val; | |
| data &= ~IFE_PMC_AUTO_MDIX; | |
| data &= ~IFE_PMC_FORCE_MDIX; | |
| ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, data); | |
| if (ret_val) | |
| return ret_val; | |
| hw_dbg(hw, "IFE PMC: %X\n", data); | |
| udelay(1); | |
| if (phy->autoneg_wait_to_complete) { | |
| hw_dbg(hw, "Waiting for forced speed/duplex link on IFE phy.\n"); | |
| ret_val = e1000e_phy_has_link_generic(hw, | |
| PHY_FORCE_LIMIT, | |
| 100000, | |
| &link); | |
| if (ret_val) | |
| return ret_val; | |
| if (!link) | |
| hw_dbg(hw, "Link taking longer than expected.\n"); | |
| /* Try once more */ | |
| ret_val = e1000e_phy_has_link_generic(hw, | |
| PHY_FORCE_LIMIT, | |
| 100000, | |
| &link); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * e1000_phy_hw_reset_ich8lan - Performs a PHY reset | |
| * @hw: pointer to the HW structure | |
| * | |
| * Resets the PHY | |
| * This is a function pointer entry point called by drivers | |
| * or other shared routines. | |
| **/ | |
| static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_phy_info *phy = &hw->phy; | |
| u32 i; | |
| u32 data, cnf_size, cnf_base_addr, sw_cfg_mask; | |
| s32 ret_val; | |
| u16 loop = E1000_ICH8_LAN_INIT_TIMEOUT; | |
| u16 word_addr, reg_data, reg_addr, phy_page = 0; | |
| ret_val = e1000e_phy_hw_reset_generic(hw); | |
| if (ret_val) | |
| return ret_val; | |
| /* | |
| * Initialize the PHY from the NVM on ICH platforms. This | |
| * is needed due to an issue where the NVM configuration is | |
| * not properly autoloaded after power transitions. | |
| * Therefore, after each PHY reset, we will load the | |
| * configuration data out of the NVM manually. | |
| */ | |
| if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) { | |
| struct e1000_adapter *adapter = hw->adapter; | |
| /* Check if SW needs configure the PHY */ | |
| if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) || | |
| (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M)) | |
| sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M; | |
| else | |
| sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG; | |
| data = er32(FEXTNVM); | |
| if (!(data & sw_cfg_mask)) | |
| return 0; | |
| /* Wait for basic configuration completes before proceeding*/ | |
| do { | |
| data = er32(STATUS); | |
| data &= E1000_STATUS_LAN_INIT_DONE; | |
| udelay(100); | |
| } while ((!data) && --loop); | |
| /* | |
| * If basic configuration is incomplete before the above loop | |
| * count reaches 0, loading the configuration from NVM will | |
| * leave the PHY in a bad state possibly resulting in no link. | |
| */ | |
| if (loop == 0) { | |
| hw_dbg(hw, "LAN_INIT_DONE not set, increase timeout\n"); | |
| } | |
| /* Clear the Init Done bit for the next init event */ | |
| data = er32(STATUS); | |
| data &= ~E1000_STATUS_LAN_INIT_DONE; | |
| ew32(STATUS, data); | |
| /* | |
| * Make sure HW does not configure LCD from PHY | |
| * extended configuration before SW configuration | |
| */ | |
| data = er32(EXTCNF_CTRL); | |
| if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) | |
| return 0; | |
| cnf_size = er32(EXTCNF_SIZE); | |
| cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK; | |
| cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT; | |
| if (!cnf_size) | |
| return 0; | |
| cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK; | |
| cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT; | |
| /* Configure LCD from extended configuration region. */ | |
| /* cnf_base_addr is in DWORD */ | |
| word_addr = (u16)(cnf_base_addr << 1); | |
| for (i = 0; i < cnf_size; i++) { | |
| ret_val = e1000_read_nvm(hw, | |
| (word_addr + i * 2), | |
| 1, | |
| ®_data); | |
| if (ret_val) | |
| return ret_val; | |
| ret_val = e1000_read_nvm(hw, | |
| (word_addr + i * 2 + 1), | |
| 1, | |
| ®_addr); | |
| if (ret_val) | |
| return ret_val; | |
| /* Save off the PHY page for future writes. */ | |
| if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) { | |
| phy_page = reg_data; | |
| continue; | |
| } | |
| reg_addr |= phy_page; | |
| ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| } | |
| return 0; | |
| } | |
| /** | |
| * e1000_get_phy_info_ife_ich8lan - Retrieves various IFE PHY states | |
| * @hw: pointer to the HW structure | |
| * | |
| * Populates "phy" structure with various feature states. | |
| * This function is only called by other family-specific | |
| * routines. | |
| **/ | |
| static s32 e1000_get_phy_info_ife_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_phy_info *phy = &hw->phy; | |
| s32 ret_val; | |
| u16 data; | |
| bool link; | |
| ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); | |
| if (ret_val) | |
| return ret_val; | |
| if (!link) { | |
| hw_dbg(hw, "Phy info is only valid if link is up\n"); | |
| return -E1000_ERR_CONFIG; | |
| } | |
| ret_val = e1e_rphy(hw, IFE_PHY_SPECIAL_CONTROL, &data); | |
| if (ret_val) | |
| return ret_val; | |
| phy->polarity_correction = (!(data & IFE_PSC_AUTO_POLARITY_DISABLE)); | |
| if (phy->polarity_correction) { | |
| ret_val = e1000_check_polarity_ife_ich8lan(hw); | |
| if (ret_val) | |
| return ret_val; | |
| } else { | |
| /* Polarity is forced */ | |
| phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY) | |
| ? e1000_rev_polarity_reversed | |
| : e1000_rev_polarity_normal; | |
| } | |
| ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); | |
| if (ret_val) | |
| return ret_val; | |
| phy->is_mdix = (data & IFE_PMC_MDIX_STATUS); | |
| /* The following parameters are undefined for 10/100 operation. */ | |
| phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; | |
| phy->local_rx = e1000_1000t_rx_status_undefined; | |
| phy->remote_rx = e1000_1000t_rx_status_undefined; | |
| return 0; | |
| } | |
| /** | |
| * e1000_get_phy_info_ich8lan - Calls appropriate PHY type get_phy_info | |
| * @hw: pointer to the HW structure | |
| * | |
| * Wrapper for calling the get_phy_info routines for the appropriate phy type. | |
| * This is a function pointer entry point called by drivers | |
| * or other shared routines. | |
| **/ | |
| static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw) | |
| { | |
| switch (hw->phy.type) { | |
| case e1000_phy_ife: | |
| return e1000_get_phy_info_ife_ich8lan(hw); | |
| break; | |
| case e1000_phy_igp_3: | |
| case e1000_phy_bm: | |
| return e1000e_get_phy_info_igp(hw); | |
| break; | |
| default: | |
| break; | |
| } | |
| return -E1000_ERR_PHY_TYPE; | |
| } | |
| /** | |
| * e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY | |
| * @hw: pointer to the HW structure | |
| * | |
| * Polarity is determined on the polarity reversal feature being enabled. | |
| * This function is only called by other family-specific | |
| * routines. | |
| **/ | |
| static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_phy_info *phy = &hw->phy; | |
| s32 ret_val; | |
| u16 phy_data, offset, mask; | |
| /* | |
| * Polarity is determined based on the reversal feature being enabled. | |
| */ | |
| if (phy->polarity_correction) { | |
| offset = IFE_PHY_EXTENDED_STATUS_CONTROL; | |
| mask = IFE_PESC_POLARITY_REVERSED; | |
| } else { | |
| offset = IFE_PHY_SPECIAL_CONTROL; | |
| mask = IFE_PSC_FORCE_POLARITY; | |
| } | |
| ret_val = e1e_rphy(hw, offset, &phy_data); | |
| if (!ret_val) | |
| phy->cable_polarity = (phy_data & mask) | |
| ? e1000_rev_polarity_reversed | |
| : e1000_rev_polarity_normal; | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state | |
| * @hw: pointer to the HW structure | |
| * @active: TRUE to enable LPLU, FALSE to disable | |
| * | |
| * Sets the LPLU D0 state according to the active flag. When | |
| * activating LPLU this function also disables smart speed | |
| * and vice versa. LPLU will not be activated unless the | |
| * device autonegotiation advertisement meets standards of | |
| * either 10 or 10/100 or 10/100/1000 at all duplexes. | |
| * This is a function pointer entry point only called by | |
| * PHY setup routines. | |
| **/ | |
| static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active) | |
| { | |
| struct e1000_phy_info *phy = &hw->phy; | |
| u32 phy_ctrl; | |
| s32 ret_val = 0; | |
| u16 data; | |
| if (phy->type == e1000_phy_ife) | |
| return ret_val; | |
| phy_ctrl = er32(PHY_CTRL); | |
| if (active) { | |
| phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; | |
| ew32(PHY_CTRL, phy_ctrl); | |
| /* | |
| * Call gig speed drop workaround on LPLU before accessing | |
| * any PHY registers | |
| */ | |
| if ((hw->mac.type == e1000_ich8lan) && | |
| (hw->phy.type == e1000_phy_igp_3)) | |
| e1000e_gig_downshift_workaround_ich8lan(hw); | |
| /* When LPLU is enabled, we should disable SmartSpeed */ | |
| ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data); | |
| data &= ~IGP01E1000_PSCFR_SMART_SPEED; | |
| ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data); | |
| if (ret_val) | |
| return ret_val; | |
| } else { | |
| phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; | |
| ew32(PHY_CTRL, phy_ctrl); | |
| /* | |
| * LPLU and SmartSpeed are mutually exclusive. LPLU is used | |
| * during Dx states where the power conservation is most | |
| * important. During driver activity we should enable | |
| * SmartSpeed, so performance is maintained. | |
| */ | |
| if (phy->smart_speed == e1000_smart_speed_on) { | |
| ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, | |
| &data); | |
| if (ret_val) | |
| return ret_val; | |
| data |= IGP01E1000_PSCFR_SMART_SPEED; | |
| ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, | |
| data); | |
| if (ret_val) | |
| return ret_val; | |
| } else if (phy->smart_speed == e1000_smart_speed_off) { | |
| ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, | |
| &data); | |
| if (ret_val) | |
| return ret_val; | |
| data &= ~IGP01E1000_PSCFR_SMART_SPEED; | |
| ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, | |
| data); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| } | |
| return 0; | |
| } | |
| /** | |
| * e1000_set_d3_lplu_state_ich8lan - Set Low Power Linkup D3 state | |
| * @hw: pointer to the HW structure | |
| * @active: TRUE to enable LPLU, FALSE to disable | |
| * | |
| * Sets the LPLU D3 state according to the active flag. When | |
| * activating LPLU this function also disables smart speed | |
| * and vice versa. LPLU will not be activated unless the | |
| * device autonegotiation advertisement meets standards of | |
| * either 10 or 10/100 or 10/100/1000 at all duplexes. | |
| * This is a function pointer entry point only called by | |
| * PHY setup routines. | |
| **/ | |
| static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active) | |
| { | |
| struct e1000_phy_info *phy = &hw->phy; | |
| u32 phy_ctrl; | |
| s32 ret_val; | |
| u16 data; | |
| phy_ctrl = er32(PHY_CTRL); | |
| if (!active) { | |
| phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; | |
| ew32(PHY_CTRL, phy_ctrl); | |
| /* | |
| * LPLU and SmartSpeed are mutually exclusive. LPLU is used | |
| * during Dx states where the power conservation is most | |
| * important. During driver activity we should enable | |
| * SmartSpeed, so performance is maintained. | |
| */ | |
| if (phy->smart_speed == e1000_smart_speed_on) { | |
| ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, | |
| &data); | |
| if (ret_val) | |
| return ret_val; | |
| data |= IGP01E1000_PSCFR_SMART_SPEED; | |
| ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, | |
| data); | |
| if (ret_val) | |
| return ret_val; | |
| } else if (phy->smart_speed == e1000_smart_speed_off) { | |
| ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, | |
| &data); | |
| if (ret_val) | |
| return ret_val; | |
| data &= ~IGP01E1000_PSCFR_SMART_SPEED; | |
| ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, | |
| data); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || | |
| (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || | |
| (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { | |
| phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; | |
| ew32(PHY_CTRL, phy_ctrl); | |
| /* | |
| * Call gig speed drop workaround on LPLU before accessing | |
| * any PHY registers | |
| */ | |
| if ((hw->mac.type == e1000_ich8lan) && | |
| (hw->phy.type == e1000_phy_igp_3)) | |
| e1000e_gig_downshift_workaround_ich8lan(hw); | |
| /* When LPLU is enabled, we should disable SmartSpeed */ | |
| ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data); | |
| if (ret_val) | |
| return ret_val; | |
| data &= ~IGP01E1000_PSCFR_SMART_SPEED; | |
| ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data); | |
| } | |
| return 0; | |
| } | |
| /** | |
| * e1000_read_nvm_ich8lan - Read word(s) from the NVM | |
| * @hw: pointer to the HW structure | |
| * @offset: The offset (in bytes) of the word(s) to read. | |
| * @words: Size of data to read in words | |
| * @data: Pointer to the word(s) to read at offset. | |
| * | |
| * Reads a word(s) from the NVM using the flash access registers. | |
| **/ | |
| static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, | |
| u16 *data) | |
| { | |
| struct e1000_nvm_info *nvm = &hw->nvm; | |
| struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; | |
| u32 act_offset; | |
| s32 ret_val; | |
| u16 i, word; | |
| if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || | |
| (words == 0)) { | |
| hw_dbg(hw, "nvm parameter(s) out of bounds\n"); | |
| return -E1000_ERR_NVM; | |
| } | |
| ret_val = e1000_acquire_swflag_ich8lan(hw); | |
| if (ret_val) | |
| return ret_val; | |
| /* Start with the bank offset, then add the relative offset. */ | |
| act_offset = (er32(EECD) & E1000_EECD_SEC1VAL) | |
| ? nvm->flash_bank_size | |
| : 0; | |
| act_offset += offset; | |
| for (i = 0; i < words; i++) { | |
| if ((dev_spec->shadow_ram) && | |
| (dev_spec->shadow_ram[offset+i].modified)) { | |
| data[i] = dev_spec->shadow_ram[offset+i].value; | |
| } else { | |
| ret_val = e1000_read_flash_word_ich8lan(hw, | |
| act_offset + i, | |
| &word); | |
| if (ret_val) | |
| break; | |
| data[i] = word; | |
| } | |
| } | |
| e1000_release_swflag_ich8lan(hw); | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_flash_cycle_init_ich8lan - Initialize flash | |
| * @hw: pointer to the HW structure | |
| * | |
| * This function does initial flash setup so that a new read/write/erase cycle | |
| * can be started. | |
| **/ | |
| static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw) | |
| { | |
| union ich8_hws_flash_status hsfsts; | |
| s32 ret_val = -E1000_ERR_NVM; | |
| s32 i = 0; | |
| hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); | |
| /* Check if the flash descriptor is valid */ | |
| if (hsfsts.hsf_status.fldesvalid == 0) { | |
| hw_dbg(hw, "Flash descriptor invalid. " | |
| "SW Sequencing must be used."); | |
| return -E1000_ERR_NVM; | |
| } | |
| /* Clear FCERR and DAEL in hw status by writing 1 */ | |
| hsfsts.hsf_status.flcerr = 1; | |
| hsfsts.hsf_status.dael = 1; | |
| ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); | |
| /* | |
| * Either we should have a hardware SPI cycle in progress | |
| * bit to check against, in order to start a new cycle or | |
| * FDONE bit should be changed in the hardware so that it | |
| * is 1 after hardware reset, which can then be used as an | |
| * indication whether a cycle is in progress or has been | |
| * completed. | |
| */ | |
| if (hsfsts.hsf_status.flcinprog == 0) { | |
| /* | |
| * There is no cycle running at present, | |
| * so we can start a cycle | |
| * Begin by setting Flash Cycle Done. | |
| */ | |
| hsfsts.hsf_status.flcdone = 1; | |
| ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); | |
| ret_val = 0; | |
| } else { | |
| /* | |
| * otherwise poll for sometime so the current | |
| * cycle has a chance to end before giving up. | |
| */ | |
| for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) { | |
| hsfsts.regval = __er16flash(hw, ICH_FLASH_HSFSTS); | |
| if (hsfsts.hsf_status.flcinprog == 0) { | |
| ret_val = 0; | |
| break; | |
| } | |
| udelay(1); | |
| } | |
| if (ret_val == 0) { | |
| /* | |
| * Successful in waiting for previous cycle to timeout, | |
| * now set the Flash Cycle Done. | |
| */ | |
| hsfsts.hsf_status.flcdone = 1; | |
| ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); | |
| } else { | |
| hw_dbg(hw, "Flash controller busy, cannot get access"); | |
| } | |
| } | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_flash_cycle_ich8lan - Starts flash cycle (read/write/erase) | |
| * @hw: pointer to the HW structure | |
| * @timeout: maximum time to wait for completion | |
| * | |
| * This function starts a flash cycle and waits for its completion. | |
| **/ | |
| static s32 e1000_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout) | |
| { | |
| union ich8_hws_flash_ctrl hsflctl; | |
| union ich8_hws_flash_status hsfsts; | |
| s32 ret_val = -E1000_ERR_NVM; | |
| u32 i = 0; | |
| /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ | |
| hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); | |
| hsflctl.hsf_ctrl.flcgo = 1; | |
| ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); | |
| /* wait till FDONE bit is set to 1 */ | |
| do { | |
| hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); | |
| if (hsfsts.hsf_status.flcdone == 1) | |
| break; | |
| udelay(1); | |
| } while (i++ < timeout); | |
| if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) | |
| return 0; | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_read_flash_word_ich8lan - Read word from flash | |
| * @hw: pointer to the HW structure | |
| * @offset: offset to data location | |
| * @data: pointer to the location for storing the data | |
| * | |
| * Reads the flash word at offset into data. Offset is converted | |
| * to bytes before read. | |
| **/ | |
| static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, | |
| u16 *data) | |
| { | |
| /* Must convert offset into bytes. */ | |
| offset <<= 1; | |
| return e1000_read_flash_data_ich8lan(hw, offset, 2, data); | |
| } | |
| /** | |
| * e1000_read_flash_data_ich8lan - Read byte or word from NVM | |
| * @hw: pointer to the HW structure | |
| * @offset: The offset (in bytes) of the byte or word to read. | |
| * @size: Size of data to read, 1=byte 2=word | |
| * @data: Pointer to the word to store the value read. | |
| * | |
| * Reads a byte or word from the NVM using the flash access registers. | |
| **/ | |
| static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, | |
| u8 size, u16 *data) | |
| { | |
| union ich8_hws_flash_status hsfsts; | |
| union ich8_hws_flash_ctrl hsflctl; | |
| u32 flash_linear_addr; | |
| u32 flash_data = 0; | |
| s32 ret_val = -E1000_ERR_NVM; | |
| u8 count = 0; | |
| if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK) | |
| return -E1000_ERR_NVM; | |
| flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) + | |
| hw->nvm.flash_base_addr; | |
| do { | |
| udelay(1); | |
| /* Steps */ | |
| ret_val = e1000_flash_cycle_init_ich8lan(hw); | |
| if (ret_val != 0) | |
| break; | |
| hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); | |
| /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ | |
| hsflctl.hsf_ctrl.fldbcount = size - 1; | |
| hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; | |
| ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); | |
| ew32flash(ICH_FLASH_FADDR, flash_linear_addr); | |
| ret_val = e1000_flash_cycle_ich8lan(hw, | |
| ICH_FLASH_READ_COMMAND_TIMEOUT); | |
| /* | |
| * Check if FCERR is set to 1, if set to 1, clear it | |
| * and try the whole sequence a few more times, else | |
| * read in (shift in) the Flash Data0, the order is | |
| * least significant byte first msb to lsb | |
| */ | |
| if (ret_val == 0) { | |
| flash_data = er32flash(ICH_FLASH_FDATA0); | |
| if (size == 1) { | |
| *data = (u8)(flash_data & 0x000000FF); | |
| } else if (size == 2) { | |
| *data = (u16)(flash_data & 0x0000FFFF); | |
| } | |
| break; | |
| } else { | |
| /* | |
| * If we've gotten here, then things are probably | |
| * completely hosed, but if the error condition is | |
| * detected, it won't hurt to give it another try... | |
| * ICH_FLASH_CYCLE_REPEAT_COUNT times. | |
| */ | |
| hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); | |
| if (hsfsts.hsf_status.flcerr == 1) { | |
| /* Repeat for some time before giving up. */ | |
| continue; | |
| } else if (hsfsts.hsf_status.flcdone == 0) { | |
| hw_dbg(hw, "Timeout error - flash cycle " | |
| "did not complete."); | |
| break; | |
| } | |
| } | |
| } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_write_nvm_ich8lan - Write word(s) to the NVM | |
| * @hw: pointer to the HW structure | |
| * @offset: The offset (in bytes) of the word(s) to write. | |
| * @words: Size of data to write in words | |
| * @data: Pointer to the word(s) to write at offset. | |
| * | |
| * Writes a byte or word to the NVM using the flash access registers. | |
| **/ | |
| static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, | |
| u16 *data) | |
| { | |
| struct e1000_nvm_info *nvm = &hw->nvm; | |
| struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; | |
| s32 ret_val; | |
| u16 i; | |
| if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || | |
| (words == 0)) { | |
| hw_dbg(hw, "nvm parameter(s) out of bounds\n"); | |
| return -E1000_ERR_NVM; | |
| } | |
| ret_val = e1000_acquire_swflag_ich8lan(hw); | |
| if (ret_val) | |
| return ret_val; | |
| for (i = 0; i < words; i++) { | |
| dev_spec->shadow_ram[offset+i].modified = 1; | |
| dev_spec->shadow_ram[offset+i].value = data[i]; | |
| } | |
| e1000_release_swflag_ich8lan(hw); | |
| return 0; | |
| } | |
| /** | |
| * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM | |
| * @hw: pointer to the HW structure | |
| * | |
| * The NVM checksum is updated by calling the generic update_nvm_checksum, | |
| * which writes the checksum to the shadow ram. The changes in the shadow | |
| * ram are then committed to the EEPROM by processing each bank at a time | |
| * checking for the modified bit and writing only the pending changes. | |
| * After a successful commit, the shadow ram is cleared and is ready for | |
| * future writes. | |
| **/ | |
| static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_nvm_info *nvm = &hw->nvm; | |
| struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; | |
| u32 i, act_offset, new_bank_offset, old_bank_offset; | |
| s32 ret_val; | |
| u16 data; | |
| ret_val = e1000e_update_nvm_checksum_generic(hw); | |
| if (ret_val) | |
| return ret_val; | |
| if (nvm->type != e1000_nvm_flash_sw) | |
| return ret_val; | |
| ret_val = e1000_acquire_swflag_ich8lan(hw); | |
| if (ret_val) | |
| return ret_val; | |
| /* | |
| * We're writing to the opposite bank so if we're on bank 1, | |
| * write to bank 0 etc. We also need to erase the segment that | |
| * is going to be written | |
| */ | |
| if (!(er32(EECD) & E1000_EECD_SEC1VAL)) { | |
| new_bank_offset = nvm->flash_bank_size; | |
| old_bank_offset = 0; | |
| e1000_erase_flash_bank_ich8lan(hw, 1); | |
| } else { | |
| old_bank_offset = nvm->flash_bank_size; | |
| new_bank_offset = 0; | |
| e1000_erase_flash_bank_ich8lan(hw, 0); | |
| } | |
| for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) { | |
| /* | |
| * Determine whether to write the value stored | |
| * in the other NVM bank or a modified value stored | |
| * in the shadow RAM | |
| */ | |
| if (dev_spec->shadow_ram[i].modified) { | |
| data = dev_spec->shadow_ram[i].value; | |
| } else { | |
| e1000_read_flash_word_ich8lan(hw, | |
| i + old_bank_offset, | |
| &data); | |
| } | |
| /* | |
| * If the word is 0x13, then make sure the signature bits | |
| * (15:14) are 11b until the commit has completed. | |
| * This will allow us to write 10b which indicates the | |
| * signature is valid. We want to do this after the write | |
| * has completed so that we don't mark the segment valid | |
| * while the write is still in progress | |
| */ | |
| if (i == E1000_ICH_NVM_SIG_WORD) | |
| data |= E1000_ICH_NVM_SIG_MASK; | |
| /* Convert offset to bytes. */ | |
| act_offset = (i + new_bank_offset) << 1; | |
| udelay(100); | |
| /* Write the bytes to the new bank. */ | |
| ret_val = e1000_retry_write_flash_byte_ich8lan(hw, | |
| act_offset, | |
| (u8)data); | |
| if (ret_val) | |
| break; | |
| udelay(100); | |
| ret_val = e1000_retry_write_flash_byte_ich8lan(hw, | |
| act_offset + 1, | |
| (u8)(data >> 8)); | |
| if (ret_val) | |
| break; | |
| } | |
| /* | |
| * Don't bother writing the segment valid bits if sector | |
| * programming failed. | |
| */ | |
| if (ret_val) { | |
| hw_dbg(hw, "Flash commit failed.\n"); | |
| e1000_release_swflag_ich8lan(hw); | |
| return ret_val; | |
| } | |
| /* | |
| * Finally validate the new segment by setting bit 15:14 | |
| * to 10b in word 0x13 , this can be done without an | |
| * erase as well since these bits are 11 to start with | |
| * and we need to change bit 14 to 0b | |
| */ | |
| act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD; | |
| e1000_read_flash_word_ich8lan(hw, act_offset, &data); | |
| data &= 0xBFFF; | |
| ret_val = e1000_retry_write_flash_byte_ich8lan(hw, | |
| act_offset * 2 + 1, | |
| (u8)(data >> 8)); | |
| if (ret_val) { | |
| e1000_release_swflag_ich8lan(hw); | |
| return ret_val; | |
| } | |
| /* | |
| * And invalidate the previously valid segment by setting | |
| * its signature word (0x13) high_byte to 0b. This can be | |
| * done without an erase because flash erase sets all bits | |
| * to 1's. We can write 1's to 0's without an erase | |
| */ | |
| act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1; | |
| ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset, 0); | |
| if (ret_val) { | |
| e1000_release_swflag_ich8lan(hw); | |
| return ret_val; | |
| } | |
| /* Great! Everything worked, we can now clear the cached entries. */ | |
| for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) { | |
| dev_spec->shadow_ram[i].modified = 0; | |
| dev_spec->shadow_ram[i].value = 0xFFFF; | |
| } | |
| e1000_release_swflag_ich8lan(hw); | |
| /* | |
| * Reload the EEPROM, or else modifications will not appear | |
| * until after the next adapter reset. | |
| */ | |
| e1000e_reload_nvm(hw); | |
| msleep(10); | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_validate_nvm_checksum_ich8lan - Validate EEPROM checksum | |
| * @hw: pointer to the HW structure | |
| * | |
| * Check to see if checksum needs to be fixed by reading bit 6 in word 0x19. | |
| * If the bit is 0, that the EEPROM had been modified, but the checksum was not | |
| * calculated, in which case we need to calculate the checksum and set bit 6. | |
| **/ | |
| static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw) | |
| { | |
| s32 ret_val; | |
| u16 data; | |
| /* | |
| * Read 0x19 and check bit 6. If this bit is 0, the checksum | |
| * needs to be fixed. This bit is an indication that the NVM | |
| * was prepared by OEM software and did not calculate the | |
| * checksum...a likely scenario. | |
| */ | |
| ret_val = e1000_read_nvm(hw, 0x19, 1, &data); | |
| if (ret_val) | |
| return ret_val; | |
| if ((data & 0x40) == 0) { | |
| data |= 0x40; | |
| ret_val = e1000_write_nvm(hw, 0x19, 1, &data); | |
| if (ret_val) | |
| return ret_val; | |
| ret_val = e1000e_update_nvm_checksum(hw); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| return e1000e_validate_nvm_checksum_generic(hw); | |
| } | |
| /** | |
| * e1000_write_flash_data_ich8lan - Writes bytes to the NVM | |
| * @hw: pointer to the HW structure | |
| * @offset: The offset (in bytes) of the byte/word to read. | |
| * @size: Size of data to read, 1=byte 2=word | |
| * @data: The byte(s) to write to the NVM. | |
| * | |
| * Writes one/two bytes to the NVM using the flash access registers. | |
| **/ | |
| static s32 e1000_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, | |
| u8 size, u16 data) | |
| { | |
| union ich8_hws_flash_status hsfsts; | |
| union ich8_hws_flash_ctrl hsflctl; | |
| u32 flash_linear_addr; | |
| u32 flash_data = 0; | |
| s32 ret_val; | |
| u8 count = 0; | |
| if (size < 1 || size > 2 || data > size * 0xff || | |
| offset > ICH_FLASH_LINEAR_ADDR_MASK) | |
| return -E1000_ERR_NVM; | |
| flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) + | |
| hw->nvm.flash_base_addr; | |
| do { | |
| udelay(1); | |
| /* Steps */ | |
| ret_val = e1000_flash_cycle_init_ich8lan(hw); | |
| if (ret_val) | |
| break; | |
| hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); | |
| /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ | |
| hsflctl.hsf_ctrl.fldbcount = size -1; | |
| hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; | |
| ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); | |
| ew32flash(ICH_FLASH_FADDR, flash_linear_addr); | |
| if (size == 1) | |
| flash_data = (u32)data & 0x00FF; | |
| else | |
| flash_data = (u32)data; | |
| ew32flash(ICH_FLASH_FDATA0, flash_data); | |
| /* | |
| * check if FCERR is set to 1 , if set to 1, clear it | |
| * and try the whole sequence a few more times else done | |
| */ | |
| ret_val = e1000_flash_cycle_ich8lan(hw, | |
| ICH_FLASH_WRITE_COMMAND_TIMEOUT); | |
| if (!ret_val) | |
| break; | |
| /* | |
| * If we're here, then things are most likely | |
| * completely hosed, but if the error condition | |
| * is detected, it won't hurt to give it another | |
| * try...ICH_FLASH_CYCLE_REPEAT_COUNT times. | |
| */ | |
| hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); | |
| if (hsfsts.hsf_status.flcerr == 1) | |
| /* Repeat for some time before giving up. */ | |
| continue; | |
| if (hsfsts.hsf_status.flcdone == 0) { | |
| hw_dbg(hw, "Timeout error - flash cycle " | |
| "did not complete."); | |
| break; | |
| } | |
| } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_write_flash_byte_ich8lan - Write a single byte to NVM | |
| * @hw: pointer to the HW structure | |
| * @offset: The index of the byte to read. | |
| * @data: The byte to write to the NVM. | |
| * | |
| * Writes a single byte to the NVM using the flash access registers. | |
| **/ | |
| static s32 e1000_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset, | |
| u8 data) | |
| { | |
| u16 word = (u16)data; | |
| return e1000_write_flash_data_ich8lan(hw, offset, 1, word); | |
| } | |
| /** | |
| * e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM | |
| * @hw: pointer to the HW structure | |
| * @offset: The offset of the byte to write. | |
| * @byte: The byte to write to the NVM. | |
| * | |
| * Writes a single byte to the NVM using the flash access registers. | |
| * Goes through a retry algorithm before giving up. | |
| **/ | |
| static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, | |
| u32 offset, u8 byte) | |
| { | |
| s32 ret_val; | |
| u16 program_retries; | |
| ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); | |
| if (!ret_val) | |
| return ret_val; | |
| for (program_retries = 0; program_retries < 100; program_retries++) { | |
| hw_dbg(hw, "Retrying Byte %2.2X at offset %u\n", byte, offset); | |
| udelay(100); | |
| ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); | |
| if (!ret_val) | |
| break; | |
| } | |
| if (program_retries == 100) | |
| return -E1000_ERR_NVM; | |
| return 0; | |
| } | |
| /** | |
| * e1000_erase_flash_bank_ich8lan - Erase a bank (4k) from NVM | |
| * @hw: pointer to the HW structure | |
| * @bank: 0 for first bank, 1 for second bank, etc. | |
| * | |
| * Erases the bank specified. Each bank is a 4k block. Banks are 0 based. | |
| * bank N is 4096 * N + flash_reg_addr. | |
| **/ | |
| static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) | |
| { | |
| struct e1000_nvm_info *nvm = &hw->nvm; | |
| union ich8_hws_flash_status hsfsts; | |
| union ich8_hws_flash_ctrl hsflctl; | |
| u32 flash_linear_addr; | |
| /* bank size is in 16bit words - adjust to bytes */ | |
| u32 flash_bank_size = nvm->flash_bank_size * 2; | |
| s32 ret_val; | |
| s32 count = 0; | |
| s32 iteration; | |
| s32 sector_size; | |
| s32 j; | |
| hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); | |
| /* | |
| * Determine HW Sector size: Read BERASE bits of hw flash status | |
| * register | |
| * 00: The Hw sector is 256 bytes, hence we need to erase 16 | |
| * consecutive sectors. The start index for the nth Hw sector | |
| * can be calculated as = bank * 4096 + n * 256 | |
| * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. | |
| * The start index for the nth Hw sector can be calculated | |
| * as = bank * 4096 | |
| * 10: The Hw sector is 8K bytes, nth sector = bank * 8192 | |
| * (ich9 only, otherwise error condition) | |
| * 11: The Hw sector is 64K bytes, nth sector = bank * 65536 | |
| */ | |
| switch (hsfsts.hsf_status.berasesz) { | |
| case 0: | |
| /* Hw sector size 256 */ | |
| sector_size = ICH_FLASH_SEG_SIZE_256; | |
| iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_256; | |
| break; | |
| case 1: | |
| sector_size = ICH_FLASH_SEG_SIZE_4K; | |
| iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_4K; | |
| break; | |
| case 2: | |
| if (hw->mac.type == e1000_ich9lan) { | |
| sector_size = ICH_FLASH_SEG_SIZE_8K; | |
| iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_8K; | |
| } else { | |
| return -E1000_ERR_NVM; | |
| } | |
| break; | |
| case 3: | |
| sector_size = ICH_FLASH_SEG_SIZE_64K; | |
| iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_64K; | |
| break; | |
| default: | |
| return -E1000_ERR_NVM; | |
| } | |
| /* Start with the base address, then add the sector offset. */ | |
| flash_linear_addr = hw->nvm.flash_base_addr; | |
| flash_linear_addr += (bank) ? (sector_size * iteration) : 0; | |
| for (j = 0; j < iteration ; j++) { | |
| do { | |
| /* Steps */ | |
| ret_val = e1000_flash_cycle_init_ich8lan(hw); | |
| if (ret_val) | |
| return ret_val; | |
| /* | |
| * Write a value 11 (block Erase) in Flash | |
| * Cycle field in hw flash control | |
| */ | |
| hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); | |
| hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; | |
| ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); | |
| /* | |
| * Write the last 24 bits of an index within the | |
| * block into Flash Linear address field in Flash | |
| * Address. | |
| */ | |
| flash_linear_addr += (j * sector_size); | |
| ew32flash(ICH_FLASH_FADDR, flash_linear_addr); | |
| ret_val = e1000_flash_cycle_ich8lan(hw, | |
| ICH_FLASH_ERASE_COMMAND_TIMEOUT); | |
| if (ret_val == 0) | |
| break; | |
| /* | |
| * Check if FCERR is set to 1. If 1, | |
| * clear it and try the whole sequence | |
| * a few more times else Done | |
| */ | |
| hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); | |
| if (hsfsts.hsf_status.flcerr == 1) | |
| /* repeat for some time before giving up */ | |
| continue; | |
| else if (hsfsts.hsf_status.flcdone == 0) | |
| return ret_val; | |
| } while (++count < ICH_FLASH_CYCLE_REPEAT_COUNT); | |
| } | |
| return 0; | |
| } | |
| /** | |
| * e1000_valid_led_default_ich8lan - Set the default LED settings | |
| * @hw: pointer to the HW structure | |
| * @data: Pointer to the LED settings | |
| * | |
| * Reads the LED default settings from the NVM to data. If the NVM LED | |
| * settings is all 0's or F's, set the LED default to a valid LED default | |
| * setting. | |
| **/ | |
| static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data) | |
| { | |
| s32 ret_val; | |
| ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data); | |
| if (ret_val) { | |
| hw_dbg(hw, "NVM Read Error\n"); | |
| return ret_val; | |
| } | |
| if (*data == ID_LED_RESERVED_0000 || | |
| *data == ID_LED_RESERVED_FFFF) | |
| *data = ID_LED_DEFAULT_ICH8LAN; | |
| return 0; | |
| } | |
| /** | |
| * e1000_get_bus_info_ich8lan - Get/Set the bus type and width | |
| * @hw: pointer to the HW structure | |
| * | |
| * ICH8 use the PCI Express bus, but does not contain a PCI Express Capability | |
| * register, so the the bus width is hard coded. | |
| **/ | |
| static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_bus_info *bus = &hw->bus; | |
| s32 ret_val; | |
| ret_val = e1000e_get_bus_info_pcie(hw); | |
| /* | |
| * ICH devices are "PCI Express"-ish. They have | |
| * a configuration space, but do not contain | |
| * PCI Express Capability registers, so bus width | |
| * must be hardcoded. | |
| */ | |
| if (bus->width == e1000_bus_width_unknown) | |
| bus->width = e1000_bus_width_pcie_x1; | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_reset_hw_ich8lan - Reset the hardware | |
| * @hw: pointer to the HW structure | |
| * | |
| * Does a full reset of the hardware which includes a reset of the PHY and | |
| * MAC. | |
| **/ | |
| static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 ctrl, icr, kab; | |
| s32 ret_val; | |
| /* | |
| * Prevent the PCI-E bus from sticking if there is no TLP connection | |
| * on the last TLP read/write transaction when MAC is reset. | |
| */ | |
| ret_val = e1000e_disable_pcie_master(hw); | |
| if (ret_val) { | |
| hw_dbg(hw, "PCI-E Master disable polling has failed.\n"); | |
| } | |
| hw_dbg(hw, "Masking off all interrupts\n"); | |
| ew32(IMC, 0xffffffff); | |
| /* | |
| * Disable the Transmit and Receive units. Then delay to allow | |
| * any pending transactions to complete before we hit the MAC | |
| * with the global reset. | |
| */ | |
| ew32(RCTL, 0); | |
| ew32(TCTL, E1000_TCTL_PSP); | |
| e1e_flush(); | |
| msleep(10); | |
| /* Workaround for ICH8 bit corruption issue in FIFO memory */ | |
| if (hw->mac.type == e1000_ich8lan) { | |
| /* Set Tx and Rx buffer allocation to 8k apiece. */ | |
| ew32(PBA, E1000_PBA_8K); | |
| /* Set Packet Buffer Size to 16k. */ | |
| ew32(PBS, E1000_PBS_16K); | |
| } | |
| ctrl = er32(CTRL); | |
| if (!e1000_check_reset_block(hw)) { | |
| /* | |
| * PHY HW reset requires MAC CORE reset at the same | |
| * time to make sure the interface between MAC and the | |
| * external PHY is reset. | |
| */ | |
| ctrl |= E1000_CTRL_PHY_RST; | |
| } | |
| ret_val = e1000_acquire_swflag_ich8lan(hw); | |
| hw_dbg(hw, "Issuing a global reset to ich8lan"); | |
| ew32(CTRL, (ctrl | E1000_CTRL_RST)); | |
| msleep(20); | |
| ret_val = e1000e_get_auto_rd_done(hw); | |
| if (ret_val) { | |
| /* | |
| * When auto config read does not complete, do not | |
| * return with an error. This can happen in situations | |
| * where there is no eeprom and prevents getting link. | |
| */ | |
| hw_dbg(hw, "Auto Read Done did not complete\n"); | |
| } | |
| ew32(IMC, 0xffffffff); | |
| icr = er32(ICR); | |
| kab = er32(KABGTXD); | |
| kab |= E1000_KABGTXD_BGSQLBIAS; | |
| ew32(KABGTXD, kab); | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_init_hw_ich8lan - Initialize the hardware | |
| * @hw: pointer to the HW structure | |
| * | |
| * Prepares the hardware for transmit and receive by doing the following: | |
| * - initialize hardware bits | |
| * - initialize LED identification | |
| * - setup receive address registers | |
| * - setup flow control | |
| * - setup transmit descriptors | |
| * - clear statistics | |
| **/ | |
| static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_mac_info *mac = &hw->mac; | |
| u32 ctrl_ext, txdctl, snoop; | |
| s32 ret_val; | |
| u16 i; | |
| e1000_initialize_hw_bits_ich8lan(hw); | |
| /* Initialize identification LED */ | |
| ret_val = e1000e_id_led_init(hw); | |
| if (ret_val) { | |
| hw_dbg(hw, "Error initializing identification LED\n"); | |
| return ret_val; | |
| } | |
| /* Setup the receive address. */ | |
| e1000e_init_rx_addrs(hw, mac->rar_entry_count); | |
| /* Zero out the Multicast HASH table */ | |
| hw_dbg(hw, "Zeroing the MTA\n"); | |
| for (i = 0; i < mac->mta_reg_count; i++) | |
| E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); | |
| /* Setup link and flow control */ | |
| ret_val = e1000_setup_link_ich8lan(hw); | |
| /* Set the transmit descriptor write-back policy for both queues */ | |
| txdctl = er32(TXDCTL(0)); | |
| txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | | |
| E1000_TXDCTL_FULL_TX_DESC_WB; | |
| txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) | | |
| E1000_TXDCTL_MAX_TX_DESC_PREFETCH; | |
| ew32(TXDCTL(0), txdctl); | |
| txdctl = er32(TXDCTL(1)); | |
| txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | | |
| E1000_TXDCTL_FULL_TX_DESC_WB; | |
| txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) | | |
| E1000_TXDCTL_MAX_TX_DESC_PREFETCH; | |
| ew32(TXDCTL(1), txdctl); | |
| /* | |
| * ICH8 has opposite polarity of no_snoop bits. | |
| * By default, we should use snoop behavior. | |
| */ | |
| if (mac->type == e1000_ich8lan) | |
| snoop = PCIE_ICH8_SNOOP_ALL; | |
| else | |
| snoop = (u32) ~(PCIE_NO_SNOOP_ALL); | |
| e1000e_set_pcie_no_snoop(hw, snoop); | |
| ctrl_ext = er32(CTRL_EXT); | |
| ctrl_ext |= E1000_CTRL_EXT_RO_DIS; | |
| ew32(CTRL_EXT, ctrl_ext); | |
| /* | |
| * Clear all of the statistics registers (clear on read). It is | |
| * important that we do this after we have tried to establish link | |
| * because the symbol error count will increment wildly if there | |
| * is no link. | |
| */ | |
| e1000_clear_hw_cntrs_ich8lan(hw); | |
| return 0; | |
| } | |
| /** | |
| * e1000_initialize_hw_bits_ich8lan - Initialize required hardware bits | |
| * @hw: pointer to the HW structure | |
| * | |
| * Sets/Clears required hardware bits necessary for correctly setting up the | |
| * hardware for transmit and receive. | |
| **/ | |
| static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 reg; | |
| /* Extended Device Control */ | |
| reg = er32(CTRL_EXT); | |
| reg |= (1 << 22); | |
| ew32(CTRL_EXT, reg); | |
| /* Transmit Descriptor Control 0 */ | |
| reg = er32(TXDCTL(0)); | |
| reg |= (1 << 22); | |
| ew32(TXDCTL(0), reg); | |
| /* Transmit Descriptor Control 1 */ | |
| reg = er32(TXDCTL(1)); | |
| reg |= (1 << 22); | |
| ew32(TXDCTL(1), reg); | |
| /* Transmit Arbitration Control 0 */ | |
| reg = er32(TARC(0)); | |
| if (hw->mac.type == e1000_ich8lan) | |
| reg |= (1 << 28) | (1 << 29); | |
| reg |= (1 << 23) | (1 << 24) | (1 << 26) | (1 << 27); | |
| ew32(TARC(0), reg); | |
| /* Transmit Arbitration Control 1 */ | |
| reg = er32(TARC(1)); | |
| if (er32(TCTL) & E1000_TCTL_MULR) | |
| reg &= ~(1 << 28); | |
| else | |
| reg |= (1 << 28); | |
| reg |= (1 << 24) | (1 << 26) | (1 << 30); | |
| ew32(TARC(1), reg); | |
| /* Device Status */ | |
| if (hw->mac.type == e1000_ich8lan) { | |
| reg = er32(STATUS); | |
| reg &= ~(1 << 31); | |
| ew32(STATUS, reg); | |
| } | |
| } | |
| /** | |
| * e1000_setup_link_ich8lan - Setup flow control and link settings | |
| * @hw: pointer to the HW structure | |
| * | |
| * Determines which flow control settings to use, then configures flow | |
| * control. Calls the appropriate media-specific link configuration | |
| * function. Assuming the adapter has a valid link partner, a valid link | |
| * should be established. Assumes the hardware has previously been reset | |
| * and the transmitter and receiver are not enabled. | |
| **/ | |
| static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw) | |
| { | |
| s32 ret_val; | |
| if (e1000_check_reset_block(hw)) | |
| return 0; | |
| /* | |
| * ICH parts do not have a word in the NVM to determine | |
| * the default flow control setting, so we explicitly | |
| * set it to full. | |
| */ | |
| if (hw->fc.type == e1000_fc_default) | |
| hw->fc.type = e1000_fc_full; | |
| hw->fc.original_type = hw->fc.type; | |
| hw_dbg(hw, "After fix-ups FlowControl is now = %x\n", hw->fc.type); | |
| /* Continue to configure the copper link. */ | |
| ret_val = e1000_setup_copper_link_ich8lan(hw); | |
| if (ret_val) | |
| return ret_val; | |
| ew32(FCTTV, hw->fc.pause_time); | |
| return e1000e_set_fc_watermarks(hw); | |
| } | |
| /** | |
| * e1000_setup_copper_link_ich8lan - Configure MAC/PHY interface | |
| * @hw: pointer to the HW structure | |
| * | |
| * Configures the kumeran interface to the PHY to wait the appropriate time | |
| * when polling the PHY, then call the generic setup_copper_link to finish | |
| * configuring the copper link. | |
| **/ | |
| static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 ctrl; | |
| s32 ret_val; | |
| u16 reg_data; | |
| ctrl = er32(CTRL); | |
| ctrl |= E1000_CTRL_SLU; | |
| ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); | |
| ew32(CTRL, ctrl); | |
| /* | |
| * Set the mac to wait the maximum time between each iteration | |
| * and increase the max iterations when polling the phy; | |
| * this fixes erroneous timeouts at 10Mbps. | |
| */ | |
| ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF); | |
| if (ret_val) | |
| return ret_val; | |
| ret_val = e1000e_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data); | |
| if (ret_val) | |
| return ret_val; | |
| reg_data |= 0x3F; | |
| ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data); | |
| if (ret_val) | |
| return ret_val; | |
| if (hw->phy.type == e1000_phy_igp_3) { | |
| ret_val = e1000e_copper_link_setup_igp(hw); | |
| if (ret_val) | |
| return ret_val; | |
| } else if (hw->phy.type == e1000_phy_bm) { | |
| ret_val = e1000e_copper_link_setup_m88(hw); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| if (hw->phy.type == e1000_phy_ife) { | |
| ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, ®_data); | |
| if (ret_val) | |
| return ret_val; | |
| reg_data &= ~IFE_PMC_AUTO_MDIX; | |
| switch (hw->phy.mdix) { | |
| case 1: | |
| reg_data &= ~IFE_PMC_FORCE_MDIX; | |
| break; | |
| case 2: | |
| reg_data |= IFE_PMC_FORCE_MDIX; | |
| break; | |
| case 0: | |
| default: | |
| reg_data |= IFE_PMC_AUTO_MDIX; | |
| break; | |
| } | |
| ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, reg_data); | |
| if (ret_val) | |
| return ret_val; | |
| } | |
| return e1000e_setup_copper_link(hw); | |
| } | |
| /** | |
| * e1000_get_link_up_info_ich8lan - Get current link speed and duplex | |
| * @hw: pointer to the HW structure | |
| * @speed: pointer to store current link speed | |
| * @duplex: pointer to store the current link duplex | |
| * | |
| * Calls the generic get_speed_and_duplex to retrieve the current link | |
| * information and then calls the Kumeran lock loss workaround for links at | |
| * gigabit speeds. | |
| **/ | |
| static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, | |
| u16 *duplex) | |
| { | |
| s32 ret_val; | |
| ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex); | |
| if (ret_val) | |
| return ret_val; | |
| if ((hw->mac.type == e1000_ich8lan) && | |
| (hw->phy.type == e1000_phy_igp_3) && | |
| (*speed == SPEED_1000)) { | |
| ret_val = e1000_kmrn_lock_loss_workaround_ich8lan(hw); | |
| } | |
| return ret_val; | |
| } | |
| /** | |
| * e1000_kmrn_lock_loss_workaround_ich8lan - Kumeran workaround | |
| * @hw: pointer to the HW structure | |
| * | |
| * Work-around for 82566 Kumeran PCS lock loss: | |
| * On link status change (i.e. PCI reset, speed change) and link is up and | |
| * speed is gigabit- | |
| * 0) if workaround is optionally disabled do nothing | |
| * 1) wait 1ms for Kumeran link to come up | |
| * 2) check Kumeran Diagnostic register PCS lock loss bit | |
| * 3) if not set the link is locked (all is good), otherwise... | |
| * 4) reset the PHY | |
| * 5) repeat up to 10 times | |
| * Note: this is only called for IGP3 copper when speed is 1gb. | |
| **/ | |
| static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw) | |
| { | |
| struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; | |
| u32 phy_ctrl; | |
| s32 ret_val; | |
| u16 i, data; | |
| bool link; | |
| if (!dev_spec->kmrn_lock_loss_workaround_enabled) | |
| return 0; | |
| /* | |
| * Make sure link is up before proceeding. If not just return. | |
| * Attempting this while link is negotiating fouled up link | |
| * stability | |
| */ | |
| ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); | |
| if (!link) | |
| return 0; | |
| for (i = 0; i < 10; i++) { | |
| /* read once to clear */ | |
| ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data); | |
| if (ret_val) | |
| return ret_val; | |
| /* and again to get new status */ | |
| ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data); | |
| if (ret_val) | |
| return ret_val; | |
| /* check for PCS lock */ | |
| if (!(data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) | |
| return 0; | |
| /* Issue PHY reset */ | |
| e1000_phy_hw_reset(hw); | |
| mdelay(5); | |
| } | |
| /* Disable GigE link negotiation */ | |
| phy_ctrl = er32(PHY_CTRL); | |
| phy_ctrl |= (E1000_PHY_CTRL_GBE_DISABLE | | |
| E1000_PHY_CTRL_NOND0A_GBE_DISABLE); | |
| ew32(PHY_CTRL, phy_ctrl); | |
| /* | |
| * Call gig speed drop workaround on Gig disable before accessing | |
| * any PHY registers | |
| */ | |
| e1000e_gig_downshift_workaround_ich8lan(hw); | |
| /* unable to acquire PCS lock */ | |
| return -E1000_ERR_PHY; | |
| } | |
| /** | |
| * e1000_set_kmrn_lock_loss_workaround_ich8lan - Set Kumeran workaround state | |
| * @hw: pointer to the HW structure | |
| * @state: boolean value used to set the current Kumeran workaround state | |
| * | |
| * If ICH8, set the current Kumeran workaround state (enabled - TRUE | |
| * /disabled - FALSE). | |
| **/ | |
| void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, | |
| bool state) | |
| { | |
| struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; | |
| if (hw->mac.type != e1000_ich8lan) { | |
| hw_dbg(hw, "Workaround applies to ICH8 only.\n"); | |
| return; | |
| } | |
| dev_spec->kmrn_lock_loss_workaround_enabled = state; | |
| } | |
| /** | |
| * e1000_ipg3_phy_powerdown_workaround_ich8lan - Power down workaround on D3 | |
| * @hw: pointer to the HW structure | |
| * | |
| * Workaround for 82566 power-down on D3 entry: | |
| * 1) disable gigabit link | |
| * 2) write VR power-down enable | |
| * 3) read it back | |
| * Continue if successful, else issue LCD reset and repeat | |
| **/ | |
| void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 reg; | |
| u16 data; | |
| u8 retry = 0; | |
| if (hw->phy.type != e1000_phy_igp_3) | |
| return; | |
| /* Try the workaround twice (if needed) */ | |
| do { | |
| /* Disable link */ | |
| reg = er32(PHY_CTRL); | |
| reg |= (E1000_PHY_CTRL_GBE_DISABLE | | |
| E1000_PHY_CTRL_NOND0A_GBE_DISABLE); | |
| ew32(PHY_CTRL, reg); | |
| /* | |
| * Call gig speed drop workaround on Gig disable before | |
| * accessing any PHY registers | |
| */ | |
| if (hw->mac.type == e1000_ich8lan) | |
| e1000e_gig_downshift_workaround_ich8lan(hw); | |
| /* Write VR power-down enable */ | |
| e1e_rphy(hw, IGP3_VR_CTRL, &data); | |
| data &= ~IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; | |
| e1e_wphy(hw, IGP3_VR_CTRL, data | IGP3_VR_CTRL_MODE_SHUTDOWN); | |
| /* Read it back and test */ | |
| e1e_rphy(hw, IGP3_VR_CTRL, &data); | |
| data &= IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; | |
| if ((data == IGP3_VR_CTRL_MODE_SHUTDOWN) || retry) | |
| break; | |
| /* Issue PHY reset and repeat at most one more time */ | |
| reg = er32(CTRL); | |
| ew32(CTRL, reg | E1000_CTRL_PHY_RST); | |
| retry++; | |
| } while (retry); | |
| } | |
| /** | |
| * e1000e_gig_downshift_workaround_ich8lan - WoL from S5 stops working | |
| * @hw: pointer to the HW structure | |
| * | |
| * Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC), | |
| * LPLU, Gig disable, MDIC PHY reset): | |
| * 1) Set Kumeran Near-end loopback | |
| * 2) Clear Kumeran Near-end loopback | |
| * Should only be called for ICH8[m] devices with IGP_3 Phy. | |
| **/ | |
| void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw) | |
| { | |
| s32 ret_val; | |
| u16 reg_data; | |
| if ((hw->mac.type != e1000_ich8lan) || | |
| (hw->phy.type != e1000_phy_igp_3)) | |
| return; | |
| ret_val = e1000e_read_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, | |
| ®_data); | |
| if (ret_val) | |
| return; | |
| reg_data |= E1000_KMRNCTRLSTA_DIAG_NELPBK; | |
| ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, | |
| reg_data); | |
| if (ret_val) | |
| return; | |
| reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK; | |
| ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, | |
| reg_data); | |
| } | |
| /** | |
| * e1000e_disable_gig_wol_ich8lan - disable gig during WoL | |
| * @hw: pointer to the HW structure | |
| * | |
| * During S0 to Sx transition, it is possible the link remains at gig | |
| * instead of negotiating to a lower speed. Before going to Sx, set | |
| * 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation | |
| * to a lower speed. | |
| * | |
| * Should only be called for ICH9 devices. | |
| **/ | |
| void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 phy_ctrl; | |
| if (hw->mac.type == e1000_ich9lan) { | |
| phy_ctrl = er32(PHY_CTRL); | |
| phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU | | |
| E1000_PHY_CTRL_GBE_DISABLE; | |
| ew32(PHY_CTRL, phy_ctrl); | |
| } | |
| return; | |
| } | |
| /** | |
| * e1000_cleanup_led_ich8lan - Restore the default LED operation | |
| * @hw: pointer to the HW structure | |
| * | |
| * Return the LED back to the default configuration. | |
| **/ | |
| static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw) | |
| { | |
| if (hw->phy.type == e1000_phy_ife) | |
| return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0); | |
| ew32(LEDCTL, hw->mac.ledctl_default); | |
| return 0; | |
| } | |
| /** | |
| * e1000_led_on_ich8lan - Turn LEDs on | |
| * @hw: pointer to the HW structure | |
| * | |
| * Turn on the LEDs. | |
| **/ | |
| static s32 e1000_led_on_ich8lan(struct e1000_hw *hw) | |
| { | |
| if (hw->phy.type == e1000_phy_ife) | |
| return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, | |
| (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); | |
| ew32(LEDCTL, hw->mac.ledctl_mode2); | |
| return 0; | |
| } | |
| /** | |
| * e1000_led_off_ich8lan - Turn LEDs off | |
| * @hw: pointer to the HW structure | |
| * | |
| * Turn off the LEDs. | |
| **/ | |
| static s32 e1000_led_off_ich8lan(struct e1000_hw *hw) | |
| { | |
| if (hw->phy.type == e1000_phy_ife) | |
| return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, | |
| (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); | |
| ew32(LEDCTL, hw->mac.ledctl_mode1); | |
| return 0; | |
| } | |
| /** | |
| * e1000_clear_hw_cntrs_ich8lan - Clear statistical counters | |
| * @hw: pointer to the HW structure | |
| * | |
| * Clears hardware counters specific to the silicon family and calls | |
| * clear_hw_cntrs_generic to clear all general purpose counters. | |
| **/ | |
| static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw) | |
| { | |
| u32 temp; | |
| e1000e_clear_hw_cntrs_base(hw); | |
| temp = er32(ALGNERRC); | |
| temp = er32(RXERRC); | |
| temp = er32(TNCRS); | |
| temp = er32(CEXTERR); | |
| temp = er32(TSCTC); | |
| temp = er32(TSCTFC); | |
| temp = er32(MGTPRC); | |
| temp = er32(MGTPDC); | |
| temp = er32(MGTPTC); | |
| temp = er32(IAC); | |
| temp = er32(ICRXOC); | |
| } | |
| static struct e1000_mac_operations ich8_mac_ops = { | |
| .mng_mode_enab = E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT, | |
| .check_for_link = e1000e_check_for_copper_link, | |
| .cleanup_led = e1000_cleanup_led_ich8lan, | |
| .clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan, | |
| .get_bus_info = e1000_get_bus_info_ich8lan, | |
| .get_link_up_info = e1000_get_link_up_info_ich8lan, | |
| .led_on = e1000_led_on_ich8lan, | |
| .led_off = e1000_led_off_ich8lan, | |
| .update_mc_addr_list = e1000e_update_mc_addr_list_generic, | |
| .reset_hw = e1000_reset_hw_ich8lan, | |
| .init_hw = e1000_init_hw_ich8lan, | |
| .setup_link = e1000_setup_link_ich8lan, | |
| .setup_physical_interface= e1000_setup_copper_link_ich8lan, | |
| }; | |
| static struct e1000_phy_operations ich8_phy_ops = { | |
| .acquire_phy = e1000_acquire_swflag_ich8lan, | |
| .check_reset_block = e1000_check_reset_block_ich8lan, | |
| .commit_phy = NULL, | |
| .force_speed_duplex = e1000_phy_force_speed_duplex_ich8lan, | |
| .get_cfg_done = e1000e_get_cfg_done, | |
| .get_cable_length = e1000e_get_cable_length_igp_2, | |
| .get_phy_info = e1000_get_phy_info_ich8lan, | |
| .read_phy_reg = e1000e_read_phy_reg_igp, | |
| .release_phy = e1000_release_swflag_ich8lan, | |
| .reset_phy = e1000_phy_hw_reset_ich8lan, | |
| .set_d0_lplu_state = e1000_set_d0_lplu_state_ich8lan, | |
| .set_d3_lplu_state = e1000_set_d3_lplu_state_ich8lan, | |
| .write_phy_reg = e1000e_write_phy_reg_igp, | |
| }; | |
| static struct e1000_nvm_operations ich8_nvm_ops = { | |
| .acquire_nvm = e1000_acquire_swflag_ich8lan, | |
| .read_nvm = e1000_read_nvm_ich8lan, | |
| .release_nvm = e1000_release_swflag_ich8lan, | |
| .update_nvm = e1000_update_nvm_checksum_ich8lan, | |
| .valid_led_default = e1000_valid_led_default_ich8lan, | |
| .validate_nvm = e1000_validate_nvm_checksum_ich8lan, | |
| .write_nvm = e1000_write_nvm_ich8lan, | |
| }; | |
| struct e1000_info e1000_ich8_info = { | |
| .mac = e1000_ich8lan, | |
| .flags = FLAG_HAS_WOL | |
| | FLAG_IS_ICH | |
| | FLAG_RX_CSUM_ENABLED | |
| | FLAG_HAS_CTRLEXT_ON_LOAD | |
| | FLAG_HAS_AMT | |
| | FLAG_HAS_FLASH | |
| | FLAG_APME_IN_WUC, | |
| .pba = 8, | |
| .get_variants = e1000_get_variants_ich8lan, | |
| .mac_ops = &ich8_mac_ops, | |
| .phy_ops = &ich8_phy_ops, | |
| .nvm_ops = &ich8_nvm_ops, | |
| }; | |
| struct e1000_info e1000_ich9_info = { | |
| .mac = e1000_ich9lan, | |
| .flags = FLAG_HAS_JUMBO_FRAMES | |
| | FLAG_IS_ICH | |
| | FLAG_HAS_WOL | |
| | FLAG_RX_CSUM_ENABLED | |
| | FLAG_HAS_CTRLEXT_ON_LOAD | |
| | FLAG_HAS_AMT | |
| | FLAG_HAS_ERT | |
| | FLAG_HAS_FLASH | |
| | FLAG_APME_IN_WUC, | |
| .pba = 10, | |
| .get_variants = e1000_get_variants_ich8lan, | |
| .mac_ops = &ich8_mac_ops, | |
| .phy_ops = &ich8_phy_ops, | |
| .nvm_ops = &ich8_nvm_ops, | |
| }; | |