| /* memctrlr.c: Driver for UltraSPARC-III memory controller. | |
| * | |
| * Copyright (C) 2001, 2007 David S. Miller (davem@davemloft.net) | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/kernel.h> | |
| #include <linux/types.h> | |
| #include <linux/slab.h> | |
| #include <linux/list.h> | |
| #include <linux/string.h> | |
| #include <linux/sched.h> | |
| #include <linux/smp.h> | |
| #include <linux/errno.h> | |
| #include <linux/init.h> | |
| #include <asm/spitfire.h> | |
| #include <asm/chmctrl.h> | |
| #include <asm/cpudata.h> | |
| #include <asm/oplib.h> | |
| #include <asm/prom.h> | |
| #include <asm/io.h> | |
| #define CHMCTRL_NDGRPS 2 | |
| #define CHMCTRL_NDIMMS 4 | |
| #define DIMMS_PER_MC (CHMCTRL_NDGRPS * CHMCTRL_NDIMMS) | |
| /* OBP memory-layout property format. */ | |
| struct obp_map { | |
| unsigned char dimm_map[144]; | |
| unsigned char pin_map[576]; | |
| }; | |
| #define DIMM_LABEL_SZ 8 | |
| struct obp_mem_layout { | |
| /* One max 8-byte string label per DIMM. Usually | |
| * this matches the label on the motherboard where | |
| * that DIMM resides. | |
| */ | |
| char dimm_labels[DIMMS_PER_MC][DIMM_LABEL_SZ]; | |
| /* If symmetric use map[0], else it is | |
| * asymmetric and map[1] should be used. | |
| */ | |
| char symmetric; | |
| struct obp_map map[2]; | |
| }; | |
| #define CHMCTRL_NBANKS 4 | |
| struct bank_info { | |
| struct mctrl_info *mp; | |
| int bank_id; | |
| u64 raw_reg; | |
| int valid; | |
| int uk; | |
| int um; | |
| int lk; | |
| int lm; | |
| int interleave; | |
| unsigned long base; | |
| unsigned long size; | |
| }; | |
| struct mctrl_info { | |
| struct list_head list; | |
| int portid; | |
| struct obp_mem_layout layout_prop; | |
| int layout_size; | |
| void __iomem *regs; | |
| u64 timing_control1; | |
| u64 timing_control2; | |
| u64 timing_control3; | |
| u64 timing_control4; | |
| u64 memaddr_control; | |
| struct bank_info logical_banks[CHMCTRL_NBANKS]; | |
| }; | |
| static LIST_HEAD(mctrl_list); | |
| /* Does BANK decode PHYS_ADDR? */ | |
| static int bank_match(struct bank_info *bp, unsigned long phys_addr) | |
| { | |
| unsigned long upper_bits = (phys_addr & PA_UPPER_BITS) >> PA_UPPER_BITS_SHIFT; | |
| unsigned long lower_bits = (phys_addr & PA_LOWER_BITS) >> PA_LOWER_BITS_SHIFT; | |
| /* Bank must be enabled to match. */ | |
| if (bp->valid == 0) | |
| return 0; | |
| /* Would BANK match upper bits? */ | |
| upper_bits ^= bp->um; /* What bits are different? */ | |
| upper_bits = ~upper_bits; /* Invert. */ | |
| upper_bits |= bp->uk; /* What bits don't matter for matching? */ | |
| upper_bits = ~upper_bits; /* Invert. */ | |
| if (upper_bits) | |
| return 0; | |
| /* Would BANK match lower bits? */ | |
| lower_bits ^= bp->lm; /* What bits are different? */ | |
| lower_bits = ~lower_bits; /* Invert. */ | |
| lower_bits |= bp->lk; /* What bits don't matter for matching? */ | |
| lower_bits = ~lower_bits; /* Invert. */ | |
| if (lower_bits) | |
| return 0; | |
| /* I always knew you'd be the one. */ | |
| return 1; | |
| } | |
| /* Given PHYS_ADDR, search memory controller banks for a match. */ | |
| static struct bank_info *find_bank(unsigned long phys_addr) | |
| { | |
| struct list_head *mctrl_head = &mctrl_list; | |
| struct list_head *mctrl_entry = mctrl_head->next; | |
| for (;;) { | |
| struct mctrl_info *mp = | |
| list_entry(mctrl_entry, struct mctrl_info, list); | |
| int bank_no; | |
| if (mctrl_entry == mctrl_head) | |
| break; | |
| mctrl_entry = mctrl_entry->next; | |
| for (bank_no = 0; bank_no < CHMCTRL_NBANKS; bank_no++) { | |
| struct bank_info *bp; | |
| bp = &mp->logical_banks[bank_no]; | |
| if (bank_match(bp, phys_addr)) | |
| return bp; | |
| } | |
| } | |
| return NULL; | |
| } | |
| /* This is the main purpose of this driver. */ | |
| #define SYNDROME_MIN -1 | |
| #define SYNDROME_MAX 144 | |
| int chmc_getunumber(int syndrome_code, | |
| unsigned long phys_addr, | |
| char *buf, int buflen) | |
| { | |
| struct bank_info *bp; | |
| struct obp_mem_layout *prop; | |
| int bank_in_controller, first_dimm; | |
| bp = find_bank(phys_addr); | |
| if (bp == NULL || | |
| syndrome_code < SYNDROME_MIN || | |
| syndrome_code > SYNDROME_MAX) { | |
| buf[0] = '?'; | |
| buf[1] = '?'; | |
| buf[2] = '?'; | |
| buf[3] = '\0'; | |
| return 0; | |
| } | |
| prop = &bp->mp->layout_prop; | |
| bank_in_controller = bp->bank_id & (CHMCTRL_NBANKS - 1); | |
| first_dimm = (bank_in_controller & (CHMCTRL_NDGRPS - 1)); | |
| first_dimm *= CHMCTRL_NDIMMS; | |
| if (syndrome_code != SYNDROME_MIN) { | |
| struct obp_map *map; | |
| int qword, where_in_line, where, map_index, map_offset; | |
| unsigned int map_val; | |
| /* Yaay, single bit error so we can figure out | |
| * the exact dimm. | |
| */ | |
| if (prop->symmetric) | |
| map = &prop->map[0]; | |
| else | |
| map = &prop->map[1]; | |
| /* Covert syndrome code into the way the bits are | |
| * positioned on the bus. | |
| */ | |
| if (syndrome_code < 144 - 16) | |
| syndrome_code += 16; | |
| else if (syndrome_code < 144) | |
| syndrome_code -= (144 - 7); | |
| else if (syndrome_code < (144 + 3)) | |
| syndrome_code -= (144 + 3 - 4); | |
| else | |
| syndrome_code -= 144 + 3; | |
| /* All this magic has to do with how a cache line | |
| * comes over the wire on Safari. A 64-bit line | |
| * comes over in 4 quadword cycles, each of which | |
| * transmit ECC/MTAG info as well as the actual | |
| * data. 144 bits per quadword, 576 total. | |
| */ | |
| #define LINE_SIZE 64 | |
| #define LINE_ADDR_MSK (LINE_SIZE - 1) | |
| #define QW_PER_LINE 4 | |
| #define QW_BYTES (LINE_SIZE / QW_PER_LINE) | |
| #define QW_BITS 144 | |
| #define LAST_BIT (576 - 1) | |
| qword = (phys_addr & LINE_ADDR_MSK) / QW_BYTES; | |
| where_in_line = ((3 - qword) * QW_BITS) + syndrome_code; | |
| where = (LAST_BIT - where_in_line); | |
| map_index = where >> 2; | |
| map_offset = where & 0x3; | |
| map_val = map->dimm_map[map_index]; | |
| map_val = ((map_val >> ((3 - map_offset) << 1)) & (2 - 1)); | |
| sprintf(buf, "%s, pin %3d", | |
| prop->dimm_labels[first_dimm + map_val], | |
| map->pin_map[where_in_line]); | |
| } else { | |
| int dimm; | |
| /* Multi-bit error, we just dump out all the | |
| * dimm labels associated with this bank. | |
| */ | |
| for (dimm = 0; dimm < CHMCTRL_NDIMMS; dimm++) { | |
| sprintf(buf, "%s ", | |
| prop->dimm_labels[first_dimm + dimm]); | |
| buf += strlen(buf); | |
| } | |
| } | |
| return 0; | |
| } | |
| /* Accessing the registers is slightly complicated. If you want | |
| * to get at the memory controller which is on the same processor | |
| * the code is executing, you must use special ASI load/store else | |
| * you go through the global mapping. | |
| */ | |
| static u64 read_mcreg(struct mctrl_info *mp, unsigned long offset) | |
| { | |
| unsigned long ret, this_cpu; | |
| preempt_disable(); | |
| this_cpu = real_hard_smp_processor_id(); | |
| if (mp->portid == this_cpu) { | |
| __asm__ __volatile__("ldxa [%1] %2, %0" | |
| : "=r" (ret) | |
| : "r" (offset), "i" (ASI_MCU_CTRL_REG)); | |
| } else { | |
| __asm__ __volatile__("ldxa [%1] %2, %0" | |
| : "=r" (ret) | |
| : "r" (mp->regs + offset), | |
| "i" (ASI_PHYS_BYPASS_EC_E)); | |
| } | |
| preempt_enable(); | |
| return ret; | |
| } | |
| #if 0 /* currently unused */ | |
| static void write_mcreg(struct mctrl_info *mp, unsigned long offset, u64 val) | |
| { | |
| if (mp->portid == smp_processor_id()) { | |
| __asm__ __volatile__("stxa %0, [%1] %2" | |
| : : "r" (val), | |
| "r" (offset), "i" (ASI_MCU_CTRL_REG)); | |
| } else { | |
| __asm__ __volatile__("ldxa %0, [%1] %2" | |
| : : "r" (val), | |
| "r" (mp->regs + offset), | |
| "i" (ASI_PHYS_BYPASS_EC_E)); | |
| } | |
| } | |
| #endif | |
| static void interpret_one_decode_reg(struct mctrl_info *mp, int which_bank, u64 val) | |
| { | |
| struct bank_info *p = &mp->logical_banks[which_bank]; | |
| p->mp = mp; | |
| p->bank_id = (CHMCTRL_NBANKS * mp->portid) + which_bank; | |
| p->raw_reg = val; | |
| p->valid = (val & MEM_DECODE_VALID) >> MEM_DECODE_VALID_SHIFT; | |
| p->uk = (val & MEM_DECODE_UK) >> MEM_DECODE_UK_SHIFT; | |
| p->um = (val & MEM_DECODE_UM) >> MEM_DECODE_UM_SHIFT; | |
| p->lk = (val & MEM_DECODE_LK) >> MEM_DECODE_LK_SHIFT; | |
| p->lm = (val & MEM_DECODE_LM) >> MEM_DECODE_LM_SHIFT; | |
| p->base = (p->um); | |
| p->base &= ~(p->uk); | |
| p->base <<= PA_UPPER_BITS_SHIFT; | |
| switch(p->lk) { | |
| case 0xf: | |
| default: | |
| p->interleave = 1; | |
| break; | |
| case 0xe: | |
| p->interleave = 2; | |
| break; | |
| case 0xc: | |
| p->interleave = 4; | |
| break; | |
| case 0x8: | |
| p->interleave = 8; | |
| break; | |
| case 0x0: | |
| p->interleave = 16; | |
| break; | |
| }; | |
| /* UK[10] is reserved, and UK[11] is not set for the SDRAM | |
| * bank size definition. | |
| */ | |
| p->size = (((unsigned long)p->uk & | |
| ((1UL << 10UL) - 1UL)) + 1UL) << PA_UPPER_BITS_SHIFT; | |
| p->size /= p->interleave; | |
| } | |
| static void fetch_decode_regs(struct mctrl_info *mp) | |
| { | |
| if (mp->layout_size == 0) | |
| return; | |
| interpret_one_decode_reg(mp, 0, | |
| read_mcreg(mp, CHMCTRL_DECODE1)); | |
| interpret_one_decode_reg(mp, 1, | |
| read_mcreg(mp, CHMCTRL_DECODE2)); | |
| interpret_one_decode_reg(mp, 2, | |
| read_mcreg(mp, CHMCTRL_DECODE3)); | |
| interpret_one_decode_reg(mp, 3, | |
| read_mcreg(mp, CHMCTRL_DECODE4)); | |
| } | |
| static int init_one_mctrl(struct device_node *dp) | |
| { | |
| struct mctrl_info *mp = kzalloc(sizeof(*mp), GFP_KERNEL); | |
| int portid = of_getintprop_default(dp, "portid", -1); | |
| const struct linux_prom64_registers *regs; | |
| const void *pval; | |
| int len; | |
| if (!mp) | |
| return -1; | |
| if (portid == -1) | |
| goto fail; | |
| mp->portid = portid; | |
| pval = of_get_property(dp, "memory-layout", &len); | |
| mp->layout_size = len; | |
| if (!pval) | |
| mp->layout_size = 0; | |
| else { | |
| if (mp->layout_size > sizeof(mp->layout_prop)) | |
| goto fail; | |
| memcpy(&mp->layout_prop, pval, len); | |
| } | |
| regs = of_get_property(dp, "reg", NULL); | |
| if (!regs || regs->reg_size != 0x48) | |
| goto fail; | |
| mp->regs = ioremap(regs->phys_addr, regs->reg_size); | |
| if (mp->regs == NULL) | |
| goto fail; | |
| if (mp->layout_size != 0UL) { | |
| mp->timing_control1 = read_mcreg(mp, CHMCTRL_TCTRL1); | |
| mp->timing_control2 = read_mcreg(mp, CHMCTRL_TCTRL2); | |
| mp->timing_control3 = read_mcreg(mp, CHMCTRL_TCTRL3); | |
| mp->timing_control4 = read_mcreg(mp, CHMCTRL_TCTRL4); | |
| mp->memaddr_control = read_mcreg(mp, CHMCTRL_MACTRL); | |
| } | |
| fetch_decode_regs(mp); | |
| list_add(&mp->list, &mctrl_list); | |
| /* Report the device. */ | |
| printk(KERN_INFO "%s: US3 memory controller at %p [%s]\n", | |
| dp->full_name, | |
| mp->regs, (mp->layout_size ? "ACTIVE" : "INACTIVE")); | |
| return 0; | |
| fail: | |
| if (mp) { | |
| if (mp->regs != NULL) | |
| iounmap(mp->regs); | |
| kfree(mp); | |
| } | |
| return -1; | |
| } | |
| static int __init chmc_init(void) | |
| { | |
| struct device_node *dp; | |
| /* This driver is only for cheetah platforms. */ | |
| if (tlb_type != cheetah && tlb_type != cheetah_plus) | |
| return -ENODEV; | |
| for_each_node_by_name(dp, "memory-controller") | |
| init_one_mctrl(dp); | |
| for_each_node_by_name(dp, "mc-us3") | |
| init_one_mctrl(dp); | |
| return 0; | |
| } | |
| static void __exit chmc_cleanup(void) | |
| { | |
| struct list_head *head = &mctrl_list; | |
| struct list_head *tmp = head->next; | |
| for (;;) { | |
| struct mctrl_info *p = | |
| list_entry(tmp, struct mctrl_info, list); | |
| if (tmp == head) | |
| break; | |
| tmp = tmp->next; | |
| list_del(&p->list); | |
| iounmap(p->regs); | |
| kfree(p); | |
| } | |
| } | |
| module_init(chmc_init); | |
| module_exit(chmc_cleanup); |