| /* | |
| * Driver for the SWIM3 (Super Woz Integrated Machine 3) | |
| * floppy controller found on Power Macintoshes. | |
| * | |
| * Copyright (C) 1996 Paul Mackerras. | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * as published by the Free Software Foundation; either version | |
| * 2 of the License, or (at your option) any later version. | |
| */ | |
| /* | |
| * TODO: | |
| * handle 2 drives | |
| * handle GCR disks | |
| */ | |
| #include <linux/stddef.h> | |
| #include <linux/kernel.h> | |
| #include <linux/sched.h> | |
| #include <linux/timer.h> | |
| #include <linux/delay.h> | |
| #include <linux/fd.h> | |
| #include <linux/ioctl.h> | |
| #include <linux/blkdev.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/module.h> | |
| #include <linux/spinlock.h> | |
| #include <asm/io.h> | |
| #include <asm/dbdma.h> | |
| #include <asm/prom.h> | |
| #include <asm/uaccess.h> | |
| #include <asm/mediabay.h> | |
| #include <asm/machdep.h> | |
| #include <asm/pmac_feature.h> | |
| static struct request_queue *swim3_queue; | |
| static struct gendisk *disks[2]; | |
| static struct request *fd_req; | |
| #define MAX_FLOPPIES 2 | |
| enum swim_state { | |
| idle, | |
| locating, | |
| seeking, | |
| settling, | |
| do_transfer, | |
| jogging, | |
| available, | |
| revalidating, | |
| ejecting | |
| }; | |
| #define REG(x) unsigned char x; char x ## _pad[15]; | |
| /* | |
| * The names for these registers mostly represent speculation on my part. | |
| * It will be interesting to see how close they are to the names Apple uses. | |
| */ | |
| struct swim3 { | |
| REG(data); | |
| REG(timer); /* counts down at 1MHz */ | |
| REG(error); | |
| REG(mode); | |
| REG(select); /* controls CA0, CA1, CA2 and LSTRB signals */ | |
| REG(setup); | |
| REG(control); /* writing bits clears them */ | |
| REG(status); /* writing bits sets them in control */ | |
| REG(intr); | |
| REG(nseek); /* # tracks to seek */ | |
| REG(ctrack); /* current track number */ | |
| REG(csect); /* current sector number */ | |
| REG(gap3); /* size of gap 3 in track format */ | |
| REG(sector); /* sector # to read or write */ | |
| REG(nsect); /* # sectors to read or write */ | |
| REG(intr_enable); | |
| }; | |
| #define control_bic control | |
| #define control_bis status | |
| /* Bits in select register */ | |
| #define CA_MASK 7 | |
| #define LSTRB 8 | |
| /* Bits in control register */ | |
| #define DO_SEEK 0x80 | |
| #define FORMAT 0x40 | |
| #define SELECT 0x20 | |
| #define WRITE_SECTORS 0x10 | |
| #define DO_ACTION 0x08 | |
| #define DRIVE2_ENABLE 0x04 | |
| #define DRIVE_ENABLE 0x02 | |
| #define INTR_ENABLE 0x01 | |
| /* Bits in status register */ | |
| #define FIFO_1BYTE 0x80 | |
| #define FIFO_2BYTE 0x40 | |
| #define ERROR 0x20 | |
| #define DATA 0x08 | |
| #define RDDATA 0x04 | |
| #define INTR_PENDING 0x02 | |
| #define MARK_BYTE 0x01 | |
| /* Bits in intr and intr_enable registers */ | |
| #define ERROR_INTR 0x20 | |
| #define DATA_CHANGED 0x10 | |
| #define TRANSFER_DONE 0x08 | |
| #define SEEN_SECTOR 0x04 | |
| #define SEEK_DONE 0x02 | |
| #define TIMER_DONE 0x01 | |
| /* Bits in error register */ | |
| #define ERR_DATA_CRC 0x80 | |
| #define ERR_ADDR_CRC 0x40 | |
| #define ERR_OVERRUN 0x04 | |
| #define ERR_UNDERRUN 0x01 | |
| /* Bits in setup register */ | |
| #define S_SW_RESET 0x80 | |
| #define S_GCR_WRITE 0x40 | |
| #define S_IBM_DRIVE 0x20 | |
| #define S_TEST_MODE 0x10 | |
| #define S_FCLK_DIV2 0x08 | |
| #define S_GCR 0x04 | |
| #define S_COPY_PROT 0x02 | |
| #define S_INV_WDATA 0x01 | |
| /* Select values for swim3_action */ | |
| #define SEEK_POSITIVE 0 | |
| #define SEEK_NEGATIVE 4 | |
| #define STEP 1 | |
| #define MOTOR_ON 2 | |
| #define MOTOR_OFF 6 | |
| #define INDEX 3 | |
| #define EJECT 7 | |
| #define SETMFM 9 | |
| #define SETGCR 13 | |
| /* Select values for swim3_select and swim3_readbit */ | |
| #define STEP_DIR 0 | |
| #define STEPPING 1 | |
| #define MOTOR_ON 2 | |
| #define RELAX 3 /* also eject in progress */ | |
| #define READ_DATA_0 4 | |
| #define TWOMEG_DRIVE 5 | |
| #define SINGLE_SIDED 6 /* drive or diskette is 4MB type? */ | |
| #define DRIVE_PRESENT 7 | |
| #define DISK_IN 8 | |
| #define WRITE_PROT 9 | |
| #define TRACK_ZERO 10 | |
| #define TACHO 11 | |
| #define READ_DATA_1 12 | |
| #define MFM_MODE 13 | |
| #define SEEK_COMPLETE 14 | |
| #define ONEMEG_MEDIA 15 | |
| /* Definitions of values used in writing and formatting */ | |
| #define DATA_ESCAPE 0x99 | |
| #define GCR_SYNC_EXC 0x3f | |
| #define GCR_SYNC_CONV 0x80 | |
| #define GCR_FIRST_MARK 0xd5 | |
| #define GCR_SECOND_MARK 0xaa | |
| #define GCR_ADDR_MARK "\xd5\xaa\x00" | |
| #define GCR_DATA_MARK "\xd5\xaa\x0b" | |
| #define GCR_SLIP_BYTE "\x27\xaa" | |
| #define GCR_SELF_SYNC "\x3f\xbf\x1e\x34\x3c\x3f" | |
| #define DATA_99 "\x99\x99" | |
| #define MFM_ADDR_MARK "\x99\xa1\x99\xa1\x99\xa1\x99\xfe" | |
| #define MFM_INDEX_MARK "\x99\xc2\x99\xc2\x99\xc2\x99\xfc" | |
| #define MFM_GAP_LEN 12 | |
| struct floppy_state { | |
| enum swim_state state; | |
| spinlock_t lock; | |
| struct swim3 __iomem *swim3; /* hardware registers */ | |
| struct dbdma_regs __iomem *dma; /* DMA controller registers */ | |
| int swim3_intr; /* interrupt number for SWIM3 */ | |
| int dma_intr; /* interrupt number for DMA channel */ | |
| int cur_cyl; /* cylinder head is on, or -1 */ | |
| int cur_sector; /* last sector we saw go past */ | |
| int req_cyl; /* the cylinder for the current r/w request */ | |
| int head; /* head number ditto */ | |
| int req_sector; /* sector number ditto */ | |
| int scount; /* # sectors we're transferring at present */ | |
| int retries; | |
| int settle_time; | |
| int secpercyl; /* disk geometry information */ | |
| int secpertrack; | |
| int total_secs; | |
| int write_prot; /* 1 if write-protected, 0 if not, -1 dunno */ | |
| struct dbdma_cmd *dma_cmd; | |
| int ref_count; | |
| int expect_cyl; | |
| struct timer_list timeout; | |
| int timeout_pending; | |
| int ejected; | |
| wait_queue_head_t wait; | |
| int wanted; | |
| struct device_node* media_bay; /* NULL when not in bay */ | |
| char dbdma_cmd_space[5 * sizeof(struct dbdma_cmd)]; | |
| }; | |
| static struct floppy_state floppy_states[MAX_FLOPPIES]; | |
| static int floppy_count = 0; | |
| static DEFINE_SPINLOCK(swim3_lock); | |
| static unsigned short write_preamble[] = { | |
| 0x4e4e, 0x4e4e, 0x4e4e, 0x4e4e, 0x4e4e, /* gap field */ | |
| 0, 0, 0, 0, 0, 0, /* sync field */ | |
| 0x99a1, 0x99a1, 0x99a1, 0x99fb, /* data address mark */ | |
| 0x990f /* no escape for 512 bytes */ | |
| }; | |
| static unsigned short write_postamble[] = { | |
| 0x9904, /* insert CRC */ | |
| 0x4e4e, 0x4e4e, | |
| 0x9908, /* stop writing */ | |
| 0, 0, 0, 0, 0, 0 | |
| }; | |
| static void swim3_select(struct floppy_state *fs, int sel); | |
| static void swim3_action(struct floppy_state *fs, int action); | |
| static int swim3_readbit(struct floppy_state *fs, int bit); | |
| static void do_fd_request(struct request_queue * q); | |
| static void start_request(struct floppy_state *fs); | |
| static void set_timeout(struct floppy_state *fs, int nticks, | |
| void (*proc)(unsigned long)); | |
| static void scan_track(struct floppy_state *fs); | |
| static void seek_track(struct floppy_state *fs, int n); | |
| static void init_dma(struct dbdma_cmd *cp, int cmd, void *buf, int count); | |
| static void setup_transfer(struct floppy_state *fs); | |
| static void act(struct floppy_state *fs); | |
| static void scan_timeout(unsigned long data); | |
| static void seek_timeout(unsigned long data); | |
| static void settle_timeout(unsigned long data); | |
| static void xfer_timeout(unsigned long data); | |
| static irqreturn_t swim3_interrupt(int irq, void *dev_id); | |
| /*static void fd_dma_interrupt(int irq, void *dev_id);*/ | |
| static int grab_drive(struct floppy_state *fs, enum swim_state state, | |
| int interruptible); | |
| static void release_drive(struct floppy_state *fs); | |
| static int fd_eject(struct floppy_state *fs); | |
| static int floppy_ioctl(struct block_device *bdev, fmode_t mode, | |
| unsigned int cmd, unsigned long param); | |
| static int floppy_open(struct block_device *bdev, fmode_t mode); | |
| static int floppy_release(struct gendisk *disk, fmode_t mode); | |
| static int floppy_check_change(struct gendisk *disk); | |
| static int floppy_revalidate(struct gendisk *disk); | |
| static void swim3_select(struct floppy_state *fs, int sel) | |
| { | |
| struct swim3 __iomem *sw = fs->swim3; | |
| out_8(&sw->select, RELAX); | |
| if (sel & 8) | |
| out_8(&sw->control_bis, SELECT); | |
| else | |
| out_8(&sw->control_bic, SELECT); | |
| out_8(&sw->select, sel & CA_MASK); | |
| } | |
| static void swim3_action(struct floppy_state *fs, int action) | |
| { | |
| struct swim3 __iomem *sw = fs->swim3; | |
| swim3_select(fs, action); | |
| udelay(1); | |
| out_8(&sw->select, sw->select | LSTRB); | |
| udelay(2); | |
| out_8(&sw->select, sw->select & ~LSTRB); | |
| udelay(1); | |
| } | |
| static int swim3_readbit(struct floppy_state *fs, int bit) | |
| { | |
| struct swim3 __iomem *sw = fs->swim3; | |
| int stat; | |
| swim3_select(fs, bit); | |
| udelay(1); | |
| stat = in_8(&sw->status); | |
| return (stat & DATA) == 0; | |
| } | |
| static void do_fd_request(struct request_queue * q) | |
| { | |
| int i; | |
| for(i=0;i<floppy_count;i++) | |
| { | |
| #ifdef CONFIG_PMAC_MEDIABAY | |
| if (floppy_states[i].media_bay && | |
| check_media_bay(floppy_states[i].media_bay, MB_FD)) | |
| continue; | |
| #endif /* CONFIG_PMAC_MEDIABAY */ | |
| start_request(&floppy_states[i]); | |
| } | |
| } | |
| static void start_request(struct floppy_state *fs) | |
| { | |
| struct request *req; | |
| unsigned long x; | |
| if (fs->state == idle && fs->wanted) { | |
| fs->state = available; | |
| wake_up(&fs->wait); | |
| return; | |
| } | |
| while (fs->state == idle && (req = elv_next_request(swim3_queue))) { | |
| #if 0 | |
| printk("do_fd_req: dev=%s cmd=%d sec=%ld nr_sec=%ld buf=%p\n", | |
| req->rq_disk->disk_name, req->cmd, | |
| (long)req->sector, req->nr_sectors, req->buffer); | |
| printk(" errors=%d current_nr_sectors=%ld\n", | |
| req->errors, req->current_nr_sectors); | |
| #endif | |
| if (req->sector < 0 || req->sector >= fs->total_secs) { | |
| end_request(req, 0); | |
| continue; | |
| } | |
| if (req->current_nr_sectors == 0) { | |
| end_request(req, 1); | |
| continue; | |
| } | |
| if (fs->ejected) { | |
| end_request(req, 0); | |
| continue; | |
| } | |
| if (rq_data_dir(req) == WRITE) { | |
| if (fs->write_prot < 0) | |
| fs->write_prot = swim3_readbit(fs, WRITE_PROT); | |
| if (fs->write_prot) { | |
| end_request(req, 0); | |
| continue; | |
| } | |
| } | |
| /* Do not remove the cast. req->sector is now a sector_t and | |
| * can be 64 bits, but it will never go past 32 bits for this | |
| * driver anyway, so we can safely cast it down and not have | |
| * to do a 64/32 division | |
| */ | |
| fs->req_cyl = ((long)req->sector) / fs->secpercyl; | |
| x = ((long)req->sector) % fs->secpercyl; | |
| fs->head = x / fs->secpertrack; | |
| fs->req_sector = x % fs->secpertrack + 1; | |
| fd_req = req; | |
| fs->state = do_transfer; | |
| fs->retries = 0; | |
| act(fs); | |
| } | |
| } | |
| static void set_timeout(struct floppy_state *fs, int nticks, | |
| void (*proc)(unsigned long)) | |
| { | |
| unsigned long flags; | |
| spin_lock_irqsave(&fs->lock, flags); | |
| if (fs->timeout_pending) | |
| del_timer(&fs->timeout); | |
| fs->timeout.expires = jiffies + nticks; | |
| fs->timeout.function = proc; | |
| fs->timeout.data = (unsigned long) fs; | |
| add_timer(&fs->timeout); | |
| fs->timeout_pending = 1; | |
| spin_unlock_irqrestore(&fs->lock, flags); | |
| } | |
| static inline void scan_track(struct floppy_state *fs) | |
| { | |
| struct swim3 __iomem *sw = fs->swim3; | |
| swim3_select(fs, READ_DATA_0); | |
| in_8(&sw->intr); /* clear SEEN_SECTOR bit */ | |
| in_8(&sw->error); | |
| out_8(&sw->intr_enable, SEEN_SECTOR); | |
| out_8(&sw->control_bis, DO_ACTION); | |
| /* enable intr when track found */ | |
| set_timeout(fs, HZ, scan_timeout); /* enable timeout */ | |
| } | |
| static inline void seek_track(struct floppy_state *fs, int n) | |
| { | |
| struct swim3 __iomem *sw = fs->swim3; | |
| if (n >= 0) { | |
| swim3_action(fs, SEEK_POSITIVE); | |
| sw->nseek = n; | |
| } else { | |
| swim3_action(fs, SEEK_NEGATIVE); | |
| sw->nseek = -n; | |
| } | |
| fs->expect_cyl = (fs->cur_cyl >= 0)? fs->cur_cyl + n: -1; | |
| swim3_select(fs, STEP); | |
| in_8(&sw->error); | |
| /* enable intr when seek finished */ | |
| out_8(&sw->intr_enable, SEEK_DONE); | |
| out_8(&sw->control_bis, DO_SEEK); | |
| set_timeout(fs, 3*HZ, seek_timeout); /* enable timeout */ | |
| fs->settle_time = 0; | |
| } | |
| static inline void init_dma(struct dbdma_cmd *cp, int cmd, | |
| void *buf, int count) | |
| { | |
| st_le16(&cp->req_count, count); | |
| st_le16(&cp->command, cmd); | |
| st_le32(&cp->phy_addr, virt_to_bus(buf)); | |
| cp->xfer_status = 0; | |
| } | |
| static inline void setup_transfer(struct floppy_state *fs) | |
| { | |
| int n; | |
| struct swim3 __iomem *sw = fs->swim3; | |
| struct dbdma_cmd *cp = fs->dma_cmd; | |
| struct dbdma_regs __iomem *dr = fs->dma; | |
| if (fd_req->current_nr_sectors <= 0) { | |
| printk(KERN_ERR "swim3: transfer 0 sectors?\n"); | |
| return; | |
| } | |
| if (rq_data_dir(fd_req) == WRITE) | |
| n = 1; | |
| else { | |
| n = fs->secpertrack - fs->req_sector + 1; | |
| if (n > fd_req->current_nr_sectors) | |
| n = fd_req->current_nr_sectors; | |
| } | |
| fs->scount = n; | |
| swim3_select(fs, fs->head? READ_DATA_1: READ_DATA_0); | |
| out_8(&sw->sector, fs->req_sector); | |
| out_8(&sw->nsect, n); | |
| out_8(&sw->gap3, 0); | |
| out_le32(&dr->cmdptr, virt_to_bus(cp)); | |
| if (rq_data_dir(fd_req) == WRITE) { | |
| /* Set up 3 dma commands: write preamble, data, postamble */ | |
| init_dma(cp, OUTPUT_MORE, write_preamble, sizeof(write_preamble)); | |
| ++cp; | |
| init_dma(cp, OUTPUT_MORE, fd_req->buffer, 512); | |
| ++cp; | |
| init_dma(cp, OUTPUT_LAST, write_postamble, sizeof(write_postamble)); | |
| } else { | |
| init_dma(cp, INPUT_LAST, fd_req->buffer, n * 512); | |
| } | |
| ++cp; | |
| out_le16(&cp->command, DBDMA_STOP); | |
| out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS); | |
| in_8(&sw->error); | |
| out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS); | |
| if (rq_data_dir(fd_req) == WRITE) | |
| out_8(&sw->control_bis, WRITE_SECTORS); | |
| in_8(&sw->intr); | |
| out_le32(&dr->control, (RUN << 16) | RUN); | |
| /* enable intr when transfer complete */ | |
| out_8(&sw->intr_enable, TRANSFER_DONE); | |
| out_8(&sw->control_bis, DO_ACTION); | |
| set_timeout(fs, 2*HZ, xfer_timeout); /* enable timeout */ | |
| } | |
| static void act(struct floppy_state *fs) | |
| { | |
| for (;;) { | |
| switch (fs->state) { | |
| case idle: | |
| return; /* XXX shouldn't get here */ | |
| case locating: | |
| if (swim3_readbit(fs, TRACK_ZERO)) { | |
| fs->cur_cyl = 0; | |
| if (fs->req_cyl == 0) | |
| fs->state = do_transfer; | |
| else | |
| fs->state = seeking; | |
| break; | |
| } | |
| scan_track(fs); | |
| return; | |
| case seeking: | |
| if (fs->cur_cyl < 0) { | |
| fs->expect_cyl = -1; | |
| fs->state = locating; | |
| break; | |
| } | |
| if (fs->req_cyl == fs->cur_cyl) { | |
| printk("whoops, seeking 0\n"); | |
| fs->state = do_transfer; | |
| break; | |
| } | |
| seek_track(fs, fs->req_cyl - fs->cur_cyl); | |
| return; | |
| case settling: | |
| /* check for SEEK_COMPLETE after 30ms */ | |
| fs->settle_time = (HZ + 32) / 33; | |
| set_timeout(fs, fs->settle_time, settle_timeout); | |
| return; | |
| case do_transfer: | |
| if (fs->cur_cyl != fs->req_cyl) { | |
| if (fs->retries > 5) { | |
| end_request(fd_req, 0); | |
| fs->state = idle; | |
| return; | |
| } | |
| fs->state = seeking; | |
| break; | |
| } | |
| setup_transfer(fs); | |
| return; | |
| case jogging: | |
| seek_track(fs, -5); | |
| return; | |
| default: | |
| printk(KERN_ERR"swim3: unknown state %d\n", fs->state); | |
| return; | |
| } | |
| } | |
| } | |
| static void scan_timeout(unsigned long data) | |
| { | |
| struct floppy_state *fs = (struct floppy_state *) data; | |
| struct swim3 __iomem *sw = fs->swim3; | |
| fs->timeout_pending = 0; | |
| out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS); | |
| out_8(&sw->select, RELAX); | |
| out_8(&sw->intr_enable, 0); | |
| fs->cur_cyl = -1; | |
| if (fs->retries > 5) { | |
| end_request(fd_req, 0); | |
| fs->state = idle; | |
| start_request(fs); | |
| } else { | |
| fs->state = jogging; | |
| act(fs); | |
| } | |
| } | |
| static void seek_timeout(unsigned long data) | |
| { | |
| struct floppy_state *fs = (struct floppy_state *) data; | |
| struct swim3 __iomem *sw = fs->swim3; | |
| fs->timeout_pending = 0; | |
| out_8(&sw->control_bic, DO_SEEK); | |
| out_8(&sw->select, RELAX); | |
| out_8(&sw->intr_enable, 0); | |
| printk(KERN_ERR "swim3: seek timeout\n"); | |
| end_request(fd_req, 0); | |
| fs->state = idle; | |
| start_request(fs); | |
| } | |
| static void settle_timeout(unsigned long data) | |
| { | |
| struct floppy_state *fs = (struct floppy_state *) data; | |
| struct swim3 __iomem *sw = fs->swim3; | |
| fs->timeout_pending = 0; | |
| if (swim3_readbit(fs, SEEK_COMPLETE)) { | |
| out_8(&sw->select, RELAX); | |
| fs->state = locating; | |
| act(fs); | |
| return; | |
| } | |
| out_8(&sw->select, RELAX); | |
| if (fs->settle_time < 2*HZ) { | |
| ++fs->settle_time; | |
| set_timeout(fs, 1, settle_timeout); | |
| return; | |
| } | |
| printk(KERN_ERR "swim3: seek settle timeout\n"); | |
| end_request(fd_req, 0); | |
| fs->state = idle; | |
| start_request(fs); | |
| } | |
| static void xfer_timeout(unsigned long data) | |
| { | |
| struct floppy_state *fs = (struct floppy_state *) data; | |
| struct swim3 __iomem *sw = fs->swim3; | |
| struct dbdma_regs __iomem *dr = fs->dma; | |
| struct dbdma_cmd *cp = fs->dma_cmd; | |
| unsigned long s; | |
| int n; | |
| fs->timeout_pending = 0; | |
| out_le32(&dr->control, RUN << 16); | |
| /* We must wait a bit for dbdma to stop */ | |
| for (n = 0; (in_le32(&dr->status) & ACTIVE) && n < 1000; n++) | |
| udelay(1); | |
| out_8(&sw->intr_enable, 0); | |
| out_8(&sw->control_bic, WRITE_SECTORS | DO_ACTION); | |
| out_8(&sw->select, RELAX); | |
| if (rq_data_dir(fd_req) == WRITE) | |
| ++cp; | |
| if (ld_le16(&cp->xfer_status) != 0) | |
| s = fs->scount - ((ld_le16(&cp->res_count) + 511) >> 9); | |
| else | |
| s = 0; | |
| fd_req->sector += s; | |
| fd_req->current_nr_sectors -= s; | |
| printk(KERN_ERR "swim3: timeout %sing sector %ld\n", | |
| (rq_data_dir(fd_req)==WRITE? "writ": "read"), (long)fd_req->sector); | |
| end_request(fd_req, 0); | |
| fs->state = idle; | |
| start_request(fs); | |
| } | |
| static irqreturn_t swim3_interrupt(int irq, void *dev_id) | |
| { | |
| struct floppy_state *fs = (struct floppy_state *) dev_id; | |
| struct swim3 __iomem *sw = fs->swim3; | |
| int intr, err, n; | |
| int stat, resid; | |
| struct dbdma_regs __iomem *dr; | |
| struct dbdma_cmd *cp; | |
| intr = in_8(&sw->intr); | |
| err = (intr & ERROR_INTR)? in_8(&sw->error): 0; | |
| if ((intr & ERROR_INTR) && fs->state != do_transfer) | |
| printk(KERN_ERR "swim3_interrupt, state=%d, dir=%x, intr=%x, err=%x\n", | |
| fs->state, rq_data_dir(fd_req), intr, err); | |
| switch (fs->state) { | |
| case locating: | |
| if (intr & SEEN_SECTOR) { | |
| out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS); | |
| out_8(&sw->select, RELAX); | |
| out_8(&sw->intr_enable, 0); | |
| del_timer(&fs->timeout); | |
| fs->timeout_pending = 0; | |
| if (sw->ctrack == 0xff) { | |
| printk(KERN_ERR "swim3: seen sector but cyl=ff?\n"); | |
| fs->cur_cyl = -1; | |
| if (fs->retries > 5) { | |
| end_request(fd_req, 0); | |
| fs->state = idle; | |
| start_request(fs); | |
| } else { | |
| fs->state = jogging; | |
| act(fs); | |
| } | |
| break; | |
| } | |
| fs->cur_cyl = sw->ctrack; | |
| fs->cur_sector = sw->csect; | |
| if (fs->expect_cyl != -1 && fs->expect_cyl != fs->cur_cyl) | |
| printk(KERN_ERR "swim3: expected cyl %d, got %d\n", | |
| fs->expect_cyl, fs->cur_cyl); | |
| fs->state = do_transfer; | |
| act(fs); | |
| } | |
| break; | |
| case seeking: | |
| case jogging: | |
| if (sw->nseek == 0) { | |
| out_8(&sw->control_bic, DO_SEEK); | |
| out_8(&sw->select, RELAX); | |
| out_8(&sw->intr_enable, 0); | |
| del_timer(&fs->timeout); | |
| fs->timeout_pending = 0; | |
| if (fs->state == seeking) | |
| ++fs->retries; | |
| fs->state = settling; | |
| act(fs); | |
| } | |
| break; | |
| case settling: | |
| out_8(&sw->intr_enable, 0); | |
| del_timer(&fs->timeout); | |
| fs->timeout_pending = 0; | |
| act(fs); | |
| break; | |
| case do_transfer: | |
| if ((intr & (ERROR_INTR | TRANSFER_DONE)) == 0) | |
| break; | |
| out_8(&sw->intr_enable, 0); | |
| out_8(&sw->control_bic, WRITE_SECTORS | DO_ACTION); | |
| out_8(&sw->select, RELAX); | |
| del_timer(&fs->timeout); | |
| fs->timeout_pending = 0; | |
| dr = fs->dma; | |
| cp = fs->dma_cmd; | |
| if (rq_data_dir(fd_req) == WRITE) | |
| ++cp; | |
| /* | |
| * Check that the main data transfer has finished. | |
| * On writing, the swim3 sometimes doesn't use | |
| * up all the bytes of the postamble, so we can still | |
| * see DMA active here. That doesn't matter as long | |
| * as all the sector data has been transferred. | |
| */ | |
| if ((intr & ERROR_INTR) == 0 && cp->xfer_status == 0) { | |
| /* wait a little while for DMA to complete */ | |
| for (n = 0; n < 100; ++n) { | |
| if (cp->xfer_status != 0) | |
| break; | |
| udelay(1); | |
| barrier(); | |
| } | |
| } | |
| /* turn off DMA */ | |
| out_le32(&dr->control, (RUN | PAUSE) << 16); | |
| stat = ld_le16(&cp->xfer_status); | |
| resid = ld_le16(&cp->res_count); | |
| if (intr & ERROR_INTR) { | |
| n = fs->scount - 1 - resid / 512; | |
| if (n > 0) { | |
| fd_req->sector += n; | |
| fd_req->current_nr_sectors -= n; | |
| fd_req->buffer += n * 512; | |
| fs->req_sector += n; | |
| } | |
| if (fs->retries < 5) { | |
| ++fs->retries; | |
| act(fs); | |
| } else { | |
| printk("swim3: error %sing block %ld (err=%x)\n", | |
| rq_data_dir(fd_req) == WRITE? "writ": "read", | |
| (long)fd_req->sector, err); | |
| end_request(fd_req, 0); | |
| fs->state = idle; | |
| } | |
| } else { | |
| if ((stat & ACTIVE) == 0 || resid != 0) { | |
| /* musta been an error */ | |
| printk(KERN_ERR "swim3: fd dma: stat=%x resid=%d\n", stat, resid); | |
| printk(KERN_ERR " state=%d, dir=%x, intr=%x, err=%x\n", | |
| fs->state, rq_data_dir(fd_req), intr, err); | |
| end_request(fd_req, 0); | |
| fs->state = idle; | |
| start_request(fs); | |
| break; | |
| } | |
| fd_req->sector += fs->scount; | |
| fd_req->current_nr_sectors -= fs->scount; | |
| fd_req->buffer += fs->scount * 512; | |
| if (fd_req->current_nr_sectors <= 0) { | |
| end_request(fd_req, 1); | |
| fs->state = idle; | |
| } else { | |
| fs->req_sector += fs->scount; | |
| if (fs->req_sector > fs->secpertrack) { | |
| fs->req_sector -= fs->secpertrack; | |
| if (++fs->head > 1) { | |
| fs->head = 0; | |
| ++fs->req_cyl; | |
| } | |
| } | |
| act(fs); | |
| } | |
| } | |
| if (fs->state == idle) | |
| start_request(fs); | |
| break; | |
| default: | |
| printk(KERN_ERR "swim3: don't know what to do in state %d\n", fs->state); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| /* | |
| static void fd_dma_interrupt(int irq, void *dev_id) | |
| { | |
| } | |
| */ | |
| static int grab_drive(struct floppy_state *fs, enum swim_state state, | |
| int interruptible) | |
| { | |
| unsigned long flags; | |
| spin_lock_irqsave(&fs->lock, flags); | |
| if (fs->state != idle) { | |
| ++fs->wanted; | |
| while (fs->state != available) { | |
| if (interruptible && signal_pending(current)) { | |
| --fs->wanted; | |
| spin_unlock_irqrestore(&fs->lock, flags); | |
| return -EINTR; | |
| } | |
| interruptible_sleep_on(&fs->wait); | |
| } | |
| --fs->wanted; | |
| } | |
| fs->state = state; | |
| spin_unlock_irqrestore(&fs->lock, flags); | |
| return 0; | |
| } | |
| static void release_drive(struct floppy_state *fs) | |
| { | |
| unsigned long flags; | |
| spin_lock_irqsave(&fs->lock, flags); | |
| fs->state = idle; | |
| start_request(fs); | |
| spin_unlock_irqrestore(&fs->lock, flags); | |
| } | |
| static int fd_eject(struct floppy_state *fs) | |
| { | |
| int err, n; | |
| err = grab_drive(fs, ejecting, 1); | |
| if (err) | |
| return err; | |
| swim3_action(fs, EJECT); | |
| for (n = 20; n > 0; --n) { | |
| if (signal_pending(current)) { | |
| err = -EINTR; | |
| break; | |
| } | |
| swim3_select(fs, RELAX); | |
| schedule_timeout_interruptible(1); | |
| if (swim3_readbit(fs, DISK_IN) == 0) | |
| break; | |
| } | |
| swim3_select(fs, RELAX); | |
| udelay(150); | |
| fs->ejected = 1; | |
| release_drive(fs); | |
| return err; | |
| } | |
| static struct floppy_struct floppy_type = | |
| { 2880,18,2,80,0,0x1B,0x00,0xCF,0x6C,NULL }; /* 7 1.44MB 3.5" */ | |
| static int floppy_ioctl(struct block_device *bdev, fmode_t mode, | |
| unsigned int cmd, unsigned long param) | |
| { | |
| struct floppy_state *fs = bdev->bd_disk->private_data; | |
| int err; | |
| if ((cmd & 0x80) && !capable(CAP_SYS_ADMIN)) | |
| return -EPERM; | |
| #ifdef CONFIG_PMAC_MEDIABAY | |
| if (fs->media_bay && check_media_bay(fs->media_bay, MB_FD)) | |
| return -ENXIO; | |
| #endif | |
| switch (cmd) { | |
| case FDEJECT: | |
| if (fs->ref_count != 1) | |
| return -EBUSY; | |
| err = fd_eject(fs); | |
| return err; | |
| case FDGETPRM: | |
| if (copy_to_user((void __user *) param, &floppy_type, | |
| sizeof(struct floppy_struct))) | |
| return -EFAULT; | |
| return 0; | |
| } | |
| return -ENOTTY; | |
| } | |
| static int floppy_open(struct block_device *bdev, fmode_t mode) | |
| { | |
| struct floppy_state *fs = bdev->bd_disk->private_data; | |
| struct swim3 __iomem *sw = fs->swim3; | |
| int n, err = 0; | |
| if (fs->ref_count == 0) { | |
| #ifdef CONFIG_PMAC_MEDIABAY | |
| if (fs->media_bay && check_media_bay(fs->media_bay, MB_FD)) | |
| return -ENXIO; | |
| #endif | |
| out_8(&sw->setup, S_IBM_DRIVE | S_FCLK_DIV2); | |
| out_8(&sw->control_bic, 0xff); | |
| out_8(&sw->mode, 0x95); | |
| udelay(10); | |
| out_8(&sw->intr_enable, 0); | |
| out_8(&sw->control_bis, DRIVE_ENABLE | INTR_ENABLE); | |
| swim3_action(fs, MOTOR_ON); | |
| fs->write_prot = -1; | |
| fs->cur_cyl = -1; | |
| for (n = 0; n < 2 * HZ; ++n) { | |
| if (n >= HZ/30 && swim3_readbit(fs, SEEK_COMPLETE)) | |
| break; | |
| if (signal_pending(current)) { | |
| err = -EINTR; | |
| break; | |
| } | |
| swim3_select(fs, RELAX); | |
| schedule_timeout_interruptible(1); | |
| } | |
| if (err == 0 && (swim3_readbit(fs, SEEK_COMPLETE) == 0 | |
| || swim3_readbit(fs, DISK_IN) == 0)) | |
| err = -ENXIO; | |
| swim3_action(fs, SETMFM); | |
| swim3_select(fs, RELAX); | |
| } else if (fs->ref_count == -1 || mode & FMODE_EXCL) | |
| return -EBUSY; | |
| if (err == 0 && (mode & FMODE_NDELAY) == 0 | |
| && (mode & (FMODE_READ|FMODE_WRITE))) { | |
| check_disk_change(bdev); | |
| if (fs->ejected) | |
| err = -ENXIO; | |
| } | |
| if (err == 0 && (mode & FMODE_WRITE)) { | |
| if (fs->write_prot < 0) | |
| fs->write_prot = swim3_readbit(fs, WRITE_PROT); | |
| if (fs->write_prot) | |
| err = -EROFS; | |
| } | |
| if (err) { | |
| if (fs->ref_count == 0) { | |
| swim3_action(fs, MOTOR_OFF); | |
| out_8(&sw->control_bic, DRIVE_ENABLE | INTR_ENABLE); | |
| swim3_select(fs, RELAX); | |
| } | |
| return err; | |
| } | |
| if (mode & FMODE_EXCL) | |
| fs->ref_count = -1; | |
| else | |
| ++fs->ref_count; | |
| return 0; | |
| } | |
| static int floppy_release(struct gendisk *disk, fmode_t mode) | |
| { | |
| struct floppy_state *fs = disk->private_data; | |
| struct swim3 __iomem *sw = fs->swim3; | |
| if (fs->ref_count > 0 && --fs->ref_count == 0) { | |
| swim3_action(fs, MOTOR_OFF); | |
| out_8(&sw->control_bic, 0xff); | |
| swim3_select(fs, RELAX); | |
| } | |
| return 0; | |
| } | |
| static int floppy_check_change(struct gendisk *disk) | |
| { | |
| struct floppy_state *fs = disk->private_data; | |
| return fs->ejected; | |
| } | |
| static int floppy_revalidate(struct gendisk *disk) | |
| { | |
| struct floppy_state *fs = disk->private_data; | |
| struct swim3 __iomem *sw; | |
| int ret, n; | |
| #ifdef CONFIG_PMAC_MEDIABAY | |
| if (fs->media_bay && check_media_bay(fs->media_bay, MB_FD)) | |
| return -ENXIO; | |
| #endif | |
| sw = fs->swim3; | |
| grab_drive(fs, revalidating, 0); | |
| out_8(&sw->intr_enable, 0); | |
| out_8(&sw->control_bis, DRIVE_ENABLE); | |
| swim3_action(fs, MOTOR_ON); /* necessary? */ | |
| fs->write_prot = -1; | |
| fs->cur_cyl = -1; | |
| mdelay(1); | |
| for (n = HZ; n > 0; --n) { | |
| if (swim3_readbit(fs, SEEK_COMPLETE)) | |
| break; | |
| if (signal_pending(current)) | |
| break; | |
| swim3_select(fs, RELAX); | |
| schedule_timeout_interruptible(1); | |
| } | |
| ret = swim3_readbit(fs, SEEK_COMPLETE) == 0 | |
| || swim3_readbit(fs, DISK_IN) == 0; | |
| if (ret) | |
| swim3_action(fs, MOTOR_OFF); | |
| else { | |
| fs->ejected = 0; | |
| swim3_action(fs, SETMFM); | |
| } | |
| swim3_select(fs, RELAX); | |
| release_drive(fs); | |
| return ret; | |
| } | |
| static struct block_device_operations floppy_fops = { | |
| .open = floppy_open, | |
| .release = floppy_release, | |
| .locked_ioctl = floppy_ioctl, | |
| .media_changed = floppy_check_change, | |
| .revalidate_disk= floppy_revalidate, | |
| }; | |
| static int swim3_add_device(struct macio_dev *mdev, int index) | |
| { | |
| struct device_node *swim = mdev->ofdev.node; | |
| struct device_node *mediabay; | |
| struct floppy_state *fs = &floppy_states[index]; | |
| int rc = -EBUSY; | |
| /* Check & Request resources */ | |
| if (macio_resource_count(mdev) < 2) { | |
| printk(KERN_WARNING "ifd%d: no address for %s\n", | |
| index, swim->full_name); | |
| return -ENXIO; | |
| } | |
| if (macio_irq_count(mdev) < 2) { | |
| printk(KERN_WARNING "fd%d: no intrs for device %s\n", | |
| index, swim->full_name); | |
| } | |
| if (macio_request_resource(mdev, 0, "swim3 (mmio)")) { | |
| printk(KERN_ERR "fd%d: can't request mmio resource for %s\n", | |
| index, swim->full_name); | |
| return -EBUSY; | |
| } | |
| if (macio_request_resource(mdev, 1, "swim3 (dma)")) { | |
| printk(KERN_ERR "fd%d: can't request dma resource for %s\n", | |
| index, swim->full_name); | |
| macio_release_resource(mdev, 0); | |
| return -EBUSY; | |
| } | |
| dev_set_drvdata(&mdev->ofdev.dev, fs); | |
| mediabay = (strcasecmp(swim->parent->type, "media-bay") == 0) ? | |
| swim->parent : NULL; | |
| if (mediabay == NULL) | |
| pmac_call_feature(PMAC_FTR_SWIM3_ENABLE, swim, 0, 1); | |
| memset(fs, 0, sizeof(*fs)); | |
| spin_lock_init(&fs->lock); | |
| fs->state = idle; | |
| fs->swim3 = (struct swim3 __iomem *) | |
| ioremap(macio_resource_start(mdev, 0), 0x200); | |
| if (fs->swim3 == NULL) { | |
| printk("fd%d: couldn't map registers for %s\n", | |
| index, swim->full_name); | |
| rc = -ENOMEM; | |
| goto out_release; | |
| } | |
| fs->dma = (struct dbdma_regs __iomem *) | |
| ioremap(macio_resource_start(mdev, 1), 0x200); | |
| if (fs->dma == NULL) { | |
| printk("fd%d: couldn't map DMA for %s\n", | |
| index, swim->full_name); | |
| iounmap(fs->swim3); | |
| rc = -ENOMEM; | |
| goto out_release; | |
| } | |
| fs->swim3_intr = macio_irq(mdev, 0); | |
| fs->dma_intr = macio_irq(mdev, 1);; | |
| fs->cur_cyl = -1; | |
| fs->cur_sector = -1; | |
| fs->secpercyl = 36; | |
| fs->secpertrack = 18; | |
| fs->total_secs = 2880; | |
| fs->media_bay = mediabay; | |
| init_waitqueue_head(&fs->wait); | |
| fs->dma_cmd = (struct dbdma_cmd *) DBDMA_ALIGN(fs->dbdma_cmd_space); | |
| memset(fs->dma_cmd, 0, 2 * sizeof(struct dbdma_cmd)); | |
| st_le16(&fs->dma_cmd[1].command, DBDMA_STOP); | |
| if (request_irq(fs->swim3_intr, swim3_interrupt, 0, "SWIM3", fs)) { | |
| printk(KERN_ERR "fd%d: couldn't request irq %d for %s\n", | |
| index, fs->swim3_intr, swim->full_name); | |
| pmac_call_feature(PMAC_FTR_SWIM3_ENABLE, swim, 0, 0); | |
| goto out_unmap; | |
| return -EBUSY; | |
| } | |
| /* | |
| if (request_irq(fs->dma_intr, fd_dma_interrupt, 0, "SWIM3-dma", fs)) { | |
| printk(KERN_ERR "Couldn't get irq %d for SWIM3 DMA", | |
| fs->dma_intr); | |
| return -EBUSY; | |
| } | |
| */ | |
| init_timer(&fs->timeout); | |
| printk(KERN_INFO "fd%d: SWIM3 floppy controller %s\n", floppy_count, | |
| mediabay ? "in media bay" : ""); | |
| return 0; | |
| out_unmap: | |
| iounmap(fs->dma); | |
| iounmap(fs->swim3); | |
| out_release: | |
| macio_release_resource(mdev, 0); | |
| macio_release_resource(mdev, 1); | |
| return rc; | |
| } | |
| static int __devinit swim3_attach(struct macio_dev *mdev, const struct of_device_id *match) | |
| { | |
| int i, rc; | |
| struct gendisk *disk; | |
| /* Add the drive */ | |
| rc = swim3_add_device(mdev, floppy_count); | |
| if (rc) | |
| return rc; | |
| /* Now create the queue if not there yet */ | |
| if (swim3_queue == NULL) { | |
| /* If we failed, there isn't much we can do as the driver is still | |
| * too dumb to remove the device, just bail out | |
| */ | |
| if (register_blkdev(FLOPPY_MAJOR, "fd")) | |
| return 0; | |
| swim3_queue = blk_init_queue(do_fd_request, &swim3_lock); | |
| if (swim3_queue == NULL) { | |
| unregister_blkdev(FLOPPY_MAJOR, "fd"); | |
| return 0; | |
| } | |
| } | |
| /* Now register that disk. Same comment about failure handling */ | |
| i = floppy_count++; | |
| disk = disks[i] = alloc_disk(1); | |
| if (disk == NULL) | |
| return 0; | |
| disk->major = FLOPPY_MAJOR; | |
| disk->first_minor = i; | |
| disk->fops = &floppy_fops; | |
| disk->private_data = &floppy_states[i]; | |
| disk->queue = swim3_queue; | |
| disk->flags |= GENHD_FL_REMOVABLE; | |
| sprintf(disk->disk_name, "fd%d", i); | |
| set_capacity(disk, 2880); | |
| add_disk(disk); | |
| return 0; | |
| } | |
| static struct of_device_id swim3_match[] = | |
| { | |
| { | |
| .name = "swim3", | |
| }, | |
| { | |
| .compatible = "ohare-swim3" | |
| }, | |
| { | |
| .compatible = "swim3" | |
| }, | |
| }; | |
| static struct macio_driver swim3_driver = | |
| { | |
| .name = "swim3", | |
| .match_table = swim3_match, | |
| .probe = swim3_attach, | |
| #if 0 | |
| .suspend = swim3_suspend, | |
| .resume = swim3_resume, | |
| #endif | |
| }; | |
| int swim3_init(void) | |
| { | |
| macio_register_driver(&swim3_driver); | |
| return 0; | |
| } | |
| module_init(swim3_init) | |
| MODULE_LICENSE("GPL"); | |
| MODULE_AUTHOR("Paul Mackerras"); | |
| MODULE_ALIAS_BLOCKDEV_MAJOR(FLOPPY_MAJOR); |