|  | /* | 
|  |  | 
|  | * l1oip.c  low level driver for tunneling layer 1 over IP | 
|  | * | 
|  | * NOTE: It is not compatible with TDMoIP nor "ISDN over IP". | 
|  | * | 
|  | * Author	Andreas Eversberg (jolly@eversberg.eu) | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or modify | 
|  | * it under the terms of the GNU General Public License as published by | 
|  | * the Free Software Foundation; either version 2, or (at your option) | 
|  | * any later version. | 
|  | * | 
|  | * This program is distributed in the hope that it will be useful, | 
|  | * but WITHOUT ANY WARRANTY; without even the implied warranty of | 
|  | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the | 
|  | * GNU General Public License for more details. | 
|  | * | 
|  | * You should have received a copy of the GNU General Public License | 
|  | * along with this program; if not, write to the Free Software | 
|  | * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. | 
|  | * | 
|  | */ | 
|  |  | 
|  | /* module parameters: | 
|  | * type: | 
|  | Value 1	= BRI | 
|  | Value 2	= PRI | 
|  | Value 3 = BRI (multi channel frame, not supported yet) | 
|  | Value 4 = PRI (multi channel frame, not supported yet) | 
|  | A multi channel frame reduces overhead to a single frame for all | 
|  | b-channels, but increases delay. | 
|  | (NOTE: Multi channel frames are not implemented yet.) | 
|  |  | 
|  | * codec: | 
|  | Value 0 = transparent (default) | 
|  | Value 1 = transfer ALAW | 
|  | Value 2 = transfer ULAW | 
|  | Value 3 = transfer generic 4 bit compression. | 
|  |  | 
|  | * ulaw: | 
|  | 0 = we use a-Law (default) | 
|  | 1 = we use u-Law | 
|  |  | 
|  | * limit: | 
|  | limitation of B-channels to control bandwidth (1...126) | 
|  | BRI: 1 or 2 | 
|  | PRI: 1-30, 31-126 (126, because dchannel ist not counted here) | 
|  | Also limited ressources are used for stack, resulting in less channels. | 
|  | It is possible to have more channels than 30 in PRI mode, this must | 
|  | be supported by the application. | 
|  |  | 
|  | * ip: | 
|  | byte representation of remote ip address (127.0.0.1 -> 127,0,0,1) | 
|  | If not given or four 0, no remote address is set. | 
|  | For multiple interfaces, concat ip addresses. (127,0,0,1,127,0,0,1) | 
|  |  | 
|  | * port: | 
|  | port number (local interface) | 
|  | If not given or 0, port 931 is used for fist instance, 932 for next... | 
|  | For multiple interfaces, different ports must be given. | 
|  |  | 
|  | * remoteport: | 
|  | port number (remote interface) | 
|  | If not given or 0, remote port equals local port | 
|  | For multiple interfaces on equal sites, different ports must be given. | 
|  |  | 
|  | * ondemand: | 
|  | 0 = fixed (always transmit packets, even when remote side timed out) | 
|  | 1 = on demand (only transmit packets, when remote side is detected) | 
|  | the default is 0 | 
|  | NOTE: ID must also be set for on demand. | 
|  |  | 
|  | * id: | 
|  | optional value to identify frames. This value must be equal on both | 
|  | peers and should be random. If omitted or 0, no ID is transmitted. | 
|  |  | 
|  | * debug: | 
|  | NOTE: only one debug value must be given for all cards | 
|  | enable debugging (see l1oip.h for debug options) | 
|  |  | 
|  |  | 
|  | Special mISDN controls: | 
|  |  | 
|  | op = MISDN_CTRL_SETPEER* | 
|  | p1 = bytes 0-3 : remote IP address in network order (left element first) | 
|  | p2 = bytes 1-2 : remote port in network order (high byte first) | 
|  | optional: | 
|  | p2 = bytes 3-4 : local port in network order (high byte first) | 
|  |  | 
|  | op = MISDN_CTRL_UNSETPEER* | 
|  |  | 
|  | * Use l1oipctrl for comfortable setting or removing ip address. | 
|  | (Layer 1 Over IP CTRL) | 
|  |  | 
|  |  | 
|  | L1oIP-Protocol | 
|  | -------------- | 
|  |  | 
|  | Frame Header: | 
|  |  | 
|  | 7 6 5 4 3 2 1 0 | 
|  | +---------------+ | 
|  | |Ver|T|I|Coding | | 
|  | +---------------+ | 
|  | |  ID byte 3 *  | | 
|  | +---------------+ | 
|  | |  ID byte 2 *  | | 
|  | +---------------+ | 
|  | |  ID byte 1 *  | | 
|  | +---------------+ | 
|  | |  ID byte 0 *  | | 
|  | +---------------+ | 
|  | |M|   Channel   | | 
|  | +---------------+ | 
|  | |    Length *   | | 
|  | +---------------+ | 
|  | | Time Base MSB | | 
|  | +---------------+ | 
|  | | Time Base LSB | | 
|  | +---------------+ | 
|  | | Data....	| | 
|  |  | 
|  | ... | 
|  |  | 
|  | |               | | 
|  | +---------------+ | 
|  | |M|   Channel   | | 
|  | +---------------+ | 
|  | |    Length *   | | 
|  | +---------------+ | 
|  | | Time Base MSB | | 
|  | +---------------+ | 
|  | | Time Base LSB | | 
|  | +---------------+ | 
|  | | Data....	| | 
|  |  | 
|  | ... | 
|  |  | 
|  |  | 
|  | * Only included in some cases. | 
|  |  | 
|  | - Ver = Version | 
|  | If version is missmatch, the frame must be ignored. | 
|  |  | 
|  | - T = Type of interface | 
|  | Must be 0 for S0 or 1 for E1. | 
|  |  | 
|  | - I = Id present | 
|  | If bit is set, four ID bytes are included in frame. | 
|  |  | 
|  | - ID = Connection ID | 
|  | Additional ID to prevent Denial of Service attacs. Also it prevents hijacking | 
|  | connections with dynamic IP. The ID should be random and must not be 0. | 
|  |  | 
|  | - Coding = Type of codec | 
|  | Must be 0 for no transcoding. Also for D-channel and other HDLC frames. | 
|  | 1 and 2 are reserved for explicitly use of a-LAW or u-LAW codec. | 
|  | 3 is used for generic table compressor. | 
|  |  | 
|  | - M = More channels to come. If this flag is 1, the following byte contains | 
|  | the length of the channel data. After the data block, the next channel will | 
|  | be defined. The flag for the last channel block (or if only one channel is | 
|  | transmitted), must be 0 and no length is given. | 
|  |  | 
|  | - Channel = Channel number | 
|  | 0 reserved | 
|  | 1-3 channel data for S0 (3 is D-channel) | 
|  | 1-31 channel data for E1 (16 is D-channel) | 
|  | 32-127 channel data for extended E1 (16 is D-channel) | 
|  |  | 
|  | - The length is used if the M-flag is 1. It is used to find the next channel | 
|  | inside frame. | 
|  | NOTE: A value of 0 equals 256 bytes of data. | 
|  | -> For larger data blocks, a single frame must be used. | 
|  | -> For larger streams, a single frame or multiple blocks with same channel ID | 
|  | must be used. | 
|  |  | 
|  | - Time Base = Timestamp of first sample in frame | 
|  | The "Time Base" is used to rearange packets and to detect packet loss. | 
|  | The 16 bits are sent in network order (MSB first) and count 1/8000 th of a | 
|  | second. This causes a wrap around each 8,192 seconds. There is no requirement | 
|  | for the initial "Time Base", but 0 should be used for the first packet. | 
|  | In case of HDLC data, this timestamp counts the packet or byte number. | 
|  |  | 
|  |  | 
|  | Two Timers: | 
|  |  | 
|  | After initialisation, a timer of 15 seconds is started. Whenever a packet is | 
|  | transmitted, the timer is reset to 15 seconds again. If the timer expires, an | 
|  | empty packet is transmitted. This keep the connection alive. | 
|  |  | 
|  | When a valid packet is received, a timer 65 seconds is started. The interface | 
|  | become ACTIVE. If the timer expires, the interface becomes INACTIVE. | 
|  |  | 
|  |  | 
|  | Dynamic IP handling: | 
|  |  | 
|  | To allow dynamic IP, the ID must be non 0. In this case, any packet with the | 
|  | correct port number and ID will be accepted. If the remote side changes its IP | 
|  | the new IP is used for all transmitted packets until it changes again. | 
|  |  | 
|  |  | 
|  | On Demand: | 
|  |  | 
|  | If the ondemand parameter is given, the remote IP is set to 0 on timeout. | 
|  | This will stop keepalive traffic to remote. If the remote is online again, | 
|  | traffic will continue to the remote address. This is useful for road warriors. | 
|  | This feature only works with ID set, otherwhise it is highly unsecure. | 
|  |  | 
|  |  | 
|  | Socket and Thread | 
|  | ----------------- | 
|  |  | 
|  | The complete socket opening and closing is done by a thread. | 
|  | When the thread opened a socket, the hc->socket descriptor is set. Whenever a | 
|  | packet shall be sent to the socket, the hc->socket must be checked wheter not | 
|  | NULL. To prevent change in socket descriptor, the hc->socket_lock must be used. | 
|  | To change the socket, a recall of l1oip_socket_open() will safely kill the | 
|  | socket process and create a new one. | 
|  |  | 
|  | */ | 
|  |  | 
|  | #define L1OIP_VERSION	0	/* 0...3 */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/mISDNif.h> | 
|  | #include <linux/mISDNhw.h> | 
|  | #include <linux/mISDNdsp.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/in.h> | 
|  | #include <linux/inet.h> | 
|  | #include <linux/workqueue.h> | 
|  | #include <linux/kthread.h> | 
|  | #include <linux/slab.h> | 
|  | #include <net/sock.h> | 
|  | #include "core.h" | 
|  | #include "l1oip.h" | 
|  |  | 
|  | static const char *l1oip_revision = "2.00"; | 
|  |  | 
|  | static int l1oip_cnt; | 
|  | static spinlock_t l1oip_lock; | 
|  | static struct list_head l1oip_ilist; | 
|  |  | 
|  | #define MAX_CARDS	16 | 
|  | static u_int type[MAX_CARDS]; | 
|  | static u_int codec[MAX_CARDS]; | 
|  | static u_int ip[MAX_CARDS * 4]; | 
|  | static u_int port[MAX_CARDS]; | 
|  | static u_int remoteport[MAX_CARDS]; | 
|  | static u_int ondemand[MAX_CARDS]; | 
|  | static u_int limit[MAX_CARDS]; | 
|  | static u_int id[MAX_CARDS]; | 
|  | static int debug; | 
|  | static int ulaw; | 
|  |  | 
|  | MODULE_AUTHOR("Andreas Eversberg"); | 
|  | MODULE_LICENSE("GPL"); | 
|  | module_param_array(type, uint, NULL, S_IRUGO | S_IWUSR); | 
|  | module_param_array(codec, uint, NULL, S_IRUGO | S_IWUSR); | 
|  | module_param_array(ip, uint, NULL, S_IRUGO | S_IWUSR); | 
|  | module_param_array(port, uint, NULL, S_IRUGO | S_IWUSR); | 
|  | module_param_array(remoteport, uint, NULL, S_IRUGO | S_IWUSR); | 
|  | module_param_array(ondemand, uint, NULL, S_IRUGO | S_IWUSR); | 
|  | module_param_array(limit, uint, NULL, S_IRUGO | S_IWUSR); | 
|  | module_param_array(id, uint, NULL, S_IRUGO | S_IWUSR); | 
|  | module_param(ulaw, uint, S_IRUGO | S_IWUSR); | 
|  | module_param(debug, uint, S_IRUGO | S_IWUSR); | 
|  |  | 
|  | /* | 
|  | * send a frame via socket, if open and restart timer | 
|  | */ | 
|  | static int | 
|  | l1oip_socket_send(struct l1oip *hc, u8 localcodec, u8 channel, u32 chanmask, | 
|  | u16 timebase, u8 *buf, int len) | 
|  | { | 
|  | u8 *p; | 
|  | u8 frame[len + 32]; | 
|  | struct socket *socket = NULL; | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: sending data to socket (len = %d)\n", | 
|  | __func__, len); | 
|  |  | 
|  | p = frame; | 
|  |  | 
|  | /* restart timer */ | 
|  | if ((int)(hc->keep_tl.expires-jiffies) < 5 * HZ) { | 
|  | del_timer(&hc->keep_tl); | 
|  | hc->keep_tl.expires = jiffies + L1OIP_KEEPALIVE * HZ; | 
|  | add_timer(&hc->keep_tl); | 
|  | } else | 
|  | hc->keep_tl.expires = jiffies + L1OIP_KEEPALIVE * HZ; | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: resetting timer\n", __func__); | 
|  |  | 
|  | /* drop if we have no remote ip or port */ | 
|  | if (!hc->sin_remote.sin_addr.s_addr || !hc->sin_remote.sin_port) { | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: dropping frame, because remote " | 
|  | "IP is not set.\n", __func__); | 
|  | return len; | 
|  | } | 
|  |  | 
|  | /* assemble frame */ | 
|  | *p++ = (L1OIP_VERSION << 6) /* version and coding */ | 
|  | | (hc->pri ? 0x20 : 0x00) /* type */ | 
|  | | (hc->id ? 0x10 : 0x00) /* id */ | 
|  | | localcodec; | 
|  | if (hc->id) { | 
|  | *p++ = hc->id >> 24; /* id */ | 
|  | *p++ = hc->id >> 16; | 
|  | *p++ = hc->id >> 8; | 
|  | *p++ = hc->id; | 
|  | } | 
|  | *p++ =  0x00 + channel; /* m-flag, channel */ | 
|  | *p++ = timebase >> 8; /* time base */ | 
|  | *p++ = timebase; | 
|  |  | 
|  | if (buf && len) { /* add data to frame */ | 
|  | if (localcodec == 1 && ulaw) | 
|  | l1oip_ulaw_to_alaw(buf, len, p); | 
|  | else if (localcodec == 2 && !ulaw) | 
|  | l1oip_alaw_to_ulaw(buf, len, p); | 
|  | else if (localcodec == 3) | 
|  | len = l1oip_law_to_4bit(buf, len, p, | 
|  | &hc->chan[channel].codecstate); | 
|  | else | 
|  | memcpy(p, buf, len); | 
|  | } | 
|  | len += p - frame; | 
|  |  | 
|  | /* check for socket in safe condition */ | 
|  | spin_lock(&hc->socket_lock); | 
|  | if (!hc->socket) { | 
|  | spin_unlock(&hc->socket_lock); | 
|  | return 0; | 
|  | } | 
|  | /* seize socket */ | 
|  | socket = hc->socket; | 
|  | hc->socket = NULL; | 
|  | spin_unlock(&hc->socket_lock); | 
|  | /* send packet */ | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: sending packet to socket (len " | 
|  | "= %d)\n", __func__, len); | 
|  | hc->sendiov.iov_base = frame; | 
|  | hc->sendiov.iov_len  = len; | 
|  | len = kernel_sendmsg(socket, &hc->sendmsg, &hc->sendiov, 1, len); | 
|  | /* give socket back */ | 
|  | hc->socket = socket; /* no locking required */ | 
|  |  | 
|  | return len; | 
|  | } | 
|  |  | 
|  |  | 
|  | /* | 
|  | * receive channel data from socket | 
|  | */ | 
|  | static void | 
|  | l1oip_socket_recv(struct l1oip *hc, u8 remotecodec, u8 channel, u16 timebase, | 
|  | u8 *buf, int len) | 
|  | { | 
|  | struct sk_buff *nskb; | 
|  | struct bchannel *bch; | 
|  | struct dchannel *dch; | 
|  | u8 *p; | 
|  | u32 rx_counter; | 
|  |  | 
|  | if (len == 0) { | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: received empty keepalive data, " | 
|  | "ignoring\n", __func__); | 
|  | return; | 
|  | } | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: received data, sending to mISDN (%d)\n", | 
|  | __func__, len); | 
|  |  | 
|  | if (channel < 1 || channel > 127) { | 
|  | printk(KERN_WARNING "%s: packet error - channel %d out of " | 
|  | "range\n", __func__, channel); | 
|  | return; | 
|  | } | 
|  | dch = hc->chan[channel].dch; | 
|  | bch = hc->chan[channel].bch; | 
|  | if (!dch && !bch) { | 
|  | printk(KERN_WARNING "%s: packet error - channel %d not in " | 
|  | "stack\n", __func__, channel); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* prepare message */ | 
|  | nskb = mI_alloc_skb((remotecodec == 3) ? (len << 1) : len, GFP_ATOMIC); | 
|  | if (!nskb) { | 
|  | printk(KERN_ERR "%s: No mem for skb.\n", __func__); | 
|  | return; | 
|  | } | 
|  | p = skb_put(nskb, (remotecodec == 3) ? (len << 1) : len); | 
|  |  | 
|  | if (remotecodec == 1 && ulaw) | 
|  | l1oip_alaw_to_ulaw(buf, len, p); | 
|  | else if (remotecodec == 2 && !ulaw) | 
|  | l1oip_ulaw_to_alaw(buf, len, p); | 
|  | else if (remotecodec == 3) | 
|  | len = l1oip_4bit_to_law(buf, len, p); | 
|  | else | 
|  | memcpy(p, buf, len); | 
|  |  | 
|  | /* send message up */ | 
|  | if (dch && len >= 2) { | 
|  | dch->rx_skb = nskb; | 
|  | recv_Dchannel(dch); | 
|  | } | 
|  | if (bch) { | 
|  | /* expand 16 bit sequence number to 32 bit sequence number */ | 
|  | rx_counter = hc->chan[channel].rx_counter; | 
|  | if (((s16)(timebase - rx_counter)) >= 0) { | 
|  | /* time has changed forward */ | 
|  | if (timebase >= (rx_counter & 0xffff)) | 
|  | rx_counter = | 
|  | (rx_counter & 0xffff0000) | timebase; | 
|  | else | 
|  | rx_counter = ((rx_counter & 0xffff0000) + 0x10000) | 
|  | | timebase; | 
|  | } else { | 
|  | /* time has changed backwards */ | 
|  | if (timebase < (rx_counter & 0xffff)) | 
|  | rx_counter = | 
|  | (rx_counter & 0xffff0000) | timebase; | 
|  | else | 
|  | rx_counter = ((rx_counter & 0xffff0000) - 0x10000) | 
|  | | timebase; | 
|  | } | 
|  | hc->chan[channel].rx_counter = rx_counter; | 
|  |  | 
|  | #ifdef REORDER_DEBUG | 
|  | if (hc->chan[channel].disorder_flag) { | 
|  | struct sk_buff *skb; | 
|  | int cnt; | 
|  | skb = hc->chan[channel].disorder_skb; | 
|  | hc->chan[channel].disorder_skb = nskb; | 
|  | nskb = skb; | 
|  | cnt = hc->chan[channel].disorder_cnt; | 
|  | hc->chan[channel].disorder_cnt = rx_counter; | 
|  | rx_counter = cnt; | 
|  | } | 
|  | hc->chan[channel].disorder_flag ^= 1; | 
|  | if (nskb) | 
|  | #endif | 
|  | queue_ch_frame(&bch->ch, PH_DATA_IND, rx_counter, nskb); | 
|  | } | 
|  | } | 
|  |  | 
|  |  | 
|  | /* | 
|  | * parse frame and extract channel data | 
|  | */ | 
|  | static void | 
|  | l1oip_socket_parse(struct l1oip *hc, struct sockaddr_in *sin, u8 *buf, int len) | 
|  | { | 
|  | u32			packet_id; | 
|  | u8			channel; | 
|  | u8			remotecodec; | 
|  | u16			timebase; | 
|  | int			m, mlen; | 
|  | int			len_start = len; /* initial frame length */ | 
|  | struct dchannel		*dch = hc->chan[hc->d_idx].dch; | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: received frame, parsing... (%d)\n", | 
|  | __func__, len); | 
|  |  | 
|  | /* check length */ | 
|  | if (len < 1 + 1 + 2) { | 
|  | printk(KERN_WARNING "%s: packet error - length %d below " | 
|  | "4 bytes\n", __func__, len); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* check version */ | 
|  | if (((*buf) >> 6) != L1OIP_VERSION) { | 
|  | printk(KERN_WARNING "%s: packet error - unknown version %d\n", | 
|  | __func__, buf[0]>>6); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* check type */ | 
|  | if (((*buf) & 0x20) && !hc->pri) { | 
|  | printk(KERN_WARNING "%s: packet error - received E1 packet " | 
|  | "on S0 interface\n", __func__); | 
|  | return; | 
|  | } | 
|  | if (!((*buf) & 0x20) && hc->pri) { | 
|  | printk(KERN_WARNING "%s: packet error - received S0 packet " | 
|  | "on E1 interface\n", __func__); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* get id flag */ | 
|  | packet_id = (*buf >> 4) & 1; | 
|  |  | 
|  | /* check coding */ | 
|  | remotecodec = (*buf) & 0x0f; | 
|  | if (remotecodec > 3) { | 
|  | printk(KERN_WARNING "%s: packet error - remotecodec %d " | 
|  | "unsupported\n", __func__, remotecodec); | 
|  | return; | 
|  | } | 
|  | buf++; | 
|  | len--; | 
|  |  | 
|  | /* check packet_id */ | 
|  | if (packet_id) { | 
|  | if (!hc->id) { | 
|  | printk(KERN_WARNING "%s: packet error - packet has id " | 
|  | "0x%x, but we have not\n", __func__, packet_id); | 
|  | return; | 
|  | } | 
|  | if (len < 4) { | 
|  | printk(KERN_WARNING "%s: packet error - packet too " | 
|  | "short for ID value\n", __func__); | 
|  | return; | 
|  | } | 
|  | packet_id = (*buf++) << 24; | 
|  | packet_id += (*buf++) << 16; | 
|  | packet_id += (*buf++) << 8; | 
|  | packet_id += (*buf++); | 
|  | len -= 4; | 
|  |  | 
|  | if (packet_id != hc->id) { | 
|  | printk(KERN_WARNING "%s: packet error - ID mismatch, " | 
|  | "got 0x%x, we 0x%x\n", | 
|  | __func__, packet_id, hc->id); | 
|  | return; | 
|  | } | 
|  | } else { | 
|  | if (hc->id) { | 
|  | printk(KERN_WARNING "%s: packet error - packet has no " | 
|  | "ID, but we have\n", __func__); | 
|  | return; | 
|  | } | 
|  | } | 
|  |  | 
|  | multiframe: | 
|  | if (len < 1) { | 
|  | printk(KERN_WARNING "%s: packet error - packet too short, " | 
|  | "channel expected at position %d.\n", | 
|  | __func__, len-len_start + 1); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* get channel and multiframe flag */ | 
|  | channel = *buf & 0x7f; | 
|  | m = *buf >> 7; | 
|  | buf++; | 
|  | len--; | 
|  |  | 
|  | /* check length on multiframe */ | 
|  | if (m) { | 
|  | if (len < 1) { | 
|  | printk(KERN_WARNING "%s: packet error - packet too " | 
|  | "short, length expected at position %d.\n", | 
|  | __func__, len_start - len - 1); | 
|  | return; | 
|  | } | 
|  |  | 
|  | mlen = *buf++; | 
|  | len--; | 
|  | if (mlen == 0) | 
|  | mlen = 256; | 
|  | if (len < mlen + 3) { | 
|  | printk(KERN_WARNING "%s: packet error - length %d at " | 
|  | "position %d exceeds total length %d.\n", | 
|  | __func__, mlen, len_start-len - 1, len_start); | 
|  | return; | 
|  | } | 
|  | if (len == mlen + 3) { | 
|  | printk(KERN_WARNING "%s: packet error - length %d at " | 
|  | "position %d will not allow additional " | 
|  | "packet.\n", | 
|  | __func__, mlen, len_start-len + 1); | 
|  | return; | 
|  | } | 
|  | } else | 
|  | mlen = len - 2; /* single frame, subtract timebase */ | 
|  |  | 
|  | if (len < 2) { | 
|  | printk(KERN_WARNING "%s: packet error - packet too short, time " | 
|  | "base expected at position %d.\n", | 
|  | __func__, len-len_start + 1); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* get time base */ | 
|  | timebase = (*buf++) << 8; | 
|  | timebase |= (*buf++); | 
|  | len -= 2; | 
|  |  | 
|  | /* if inactive, we send up a PH_ACTIVATE and activate */ | 
|  | if (!test_bit(FLG_ACTIVE, &dch->Flags)) { | 
|  | if (debug & (DEBUG_L1OIP_MSG | DEBUG_L1OIP_SOCKET)) | 
|  | printk(KERN_DEBUG "%s: interface become active due to " | 
|  | "received packet\n", __func__); | 
|  | test_and_set_bit(FLG_ACTIVE, &dch->Flags); | 
|  | _queue_data(&dch->dev.D, PH_ACTIVATE_IND, MISDN_ID_ANY, 0, | 
|  | NULL, GFP_ATOMIC); | 
|  | } | 
|  |  | 
|  | /* distribute packet */ | 
|  | l1oip_socket_recv(hc, remotecodec, channel, timebase, buf, mlen); | 
|  | buf += mlen; | 
|  | len -= mlen; | 
|  |  | 
|  | /* multiframe */ | 
|  | if (m) | 
|  | goto multiframe; | 
|  |  | 
|  | /* restart timer */ | 
|  | if ((int)(hc->timeout_tl.expires-jiffies) < 5 * HZ || !hc->timeout_on) { | 
|  | hc->timeout_on = 1; | 
|  | del_timer(&hc->timeout_tl); | 
|  | hc->timeout_tl.expires = jiffies + L1OIP_TIMEOUT * HZ; | 
|  | add_timer(&hc->timeout_tl); | 
|  | } else /* only adjust timer */ | 
|  | hc->timeout_tl.expires = jiffies + L1OIP_TIMEOUT * HZ; | 
|  |  | 
|  | /* if ip or source port changes */ | 
|  | if ((hc->sin_remote.sin_addr.s_addr != sin->sin_addr.s_addr) | 
|  | || (hc->sin_remote.sin_port != sin->sin_port)) { | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: remote address changes from " | 
|  | "0x%08x to 0x%08x (port %d to %d)\n", __func__, | 
|  | ntohl(hc->sin_remote.sin_addr.s_addr), | 
|  | ntohl(sin->sin_addr.s_addr), | 
|  | ntohs(hc->sin_remote.sin_port), | 
|  | ntohs(sin->sin_port)); | 
|  | hc->sin_remote.sin_addr.s_addr = sin->sin_addr.s_addr; | 
|  | hc->sin_remote.sin_port = sin->sin_port; | 
|  | } | 
|  | } | 
|  |  | 
|  |  | 
|  | /* | 
|  | * socket stuff | 
|  | */ | 
|  | static int | 
|  | l1oip_socket_thread(void *data) | 
|  | { | 
|  | struct l1oip *hc = (struct l1oip *)data; | 
|  | int ret = 0; | 
|  | struct msghdr msg; | 
|  | struct sockaddr_in sin_rx; | 
|  | unsigned char *recvbuf; | 
|  | size_t recvbuf_size = 1500; | 
|  | int recvlen; | 
|  | struct socket *socket = NULL; | 
|  | DECLARE_COMPLETION_ONSTACK(wait); | 
|  |  | 
|  | /* allocate buffer memory */ | 
|  | recvbuf = kmalloc(recvbuf_size, GFP_KERNEL); | 
|  | if (!recvbuf) { | 
|  | printk(KERN_ERR "%s: Failed to alloc recvbuf.\n", __func__); | 
|  | ret = -ENOMEM; | 
|  | goto fail; | 
|  | } | 
|  |  | 
|  | /* make daemon */ | 
|  | allow_signal(SIGTERM); | 
|  |  | 
|  | /* create socket */ | 
|  | if (sock_create(PF_INET, SOCK_DGRAM, IPPROTO_UDP, &socket)) { | 
|  | printk(KERN_ERR "%s: Failed to create socket.\n", __func__); | 
|  | ret = -EIO; | 
|  | goto fail; | 
|  | } | 
|  |  | 
|  | /* set incoming address */ | 
|  | hc->sin_local.sin_family = AF_INET; | 
|  | hc->sin_local.sin_addr.s_addr = INADDR_ANY; | 
|  | hc->sin_local.sin_port = htons((unsigned short)hc->localport); | 
|  |  | 
|  | /* set outgoing address */ | 
|  | hc->sin_remote.sin_family = AF_INET; | 
|  | hc->sin_remote.sin_addr.s_addr = htonl(hc->remoteip); | 
|  | hc->sin_remote.sin_port = htons((unsigned short)hc->remoteport); | 
|  |  | 
|  | /* bind to incoming port */ | 
|  | if (socket->ops->bind(socket, (struct sockaddr *)&hc->sin_local, | 
|  | sizeof(hc->sin_local))) { | 
|  | printk(KERN_ERR "%s: Failed to bind socket to port %d.\n", | 
|  | __func__, hc->localport); | 
|  | ret = -EINVAL; | 
|  | goto fail; | 
|  | } | 
|  |  | 
|  | /* check sk */ | 
|  | if (socket->sk == NULL) { | 
|  | printk(KERN_ERR "%s: socket->sk == NULL\n", __func__); | 
|  | ret = -EIO; | 
|  | goto fail; | 
|  | } | 
|  |  | 
|  | /* build receive message */ | 
|  | msg.msg_name = &sin_rx; | 
|  | msg.msg_namelen = sizeof(sin_rx); | 
|  | msg.msg_control = NULL; | 
|  | msg.msg_controllen = 0; | 
|  |  | 
|  | /* build send message */ | 
|  | hc->sendmsg.msg_name = &hc->sin_remote; | 
|  | hc->sendmsg.msg_namelen = sizeof(hc->sin_remote); | 
|  | hc->sendmsg.msg_control = NULL; | 
|  | hc->sendmsg.msg_controllen = 0; | 
|  |  | 
|  | /* give away socket */ | 
|  | spin_lock(&hc->socket_lock); | 
|  | hc->socket = socket; | 
|  | spin_unlock(&hc->socket_lock); | 
|  |  | 
|  | /* read loop */ | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: socket created and open\n", | 
|  | __func__); | 
|  | while (!signal_pending(current)) { | 
|  | struct kvec iov = { | 
|  | .iov_base = recvbuf, | 
|  | .iov_len = recvbuf_size, | 
|  | }; | 
|  | recvlen = kernel_recvmsg(socket, &msg, &iov, 1, | 
|  | recvbuf_size, 0); | 
|  | if (recvlen > 0) { | 
|  | l1oip_socket_parse(hc, &sin_rx, recvbuf, recvlen); | 
|  | } else { | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_WARNING | 
|  | "%s: broken pipe on socket\n", __func__); | 
|  | } | 
|  | } | 
|  |  | 
|  | /* get socket back, check first if in use, maybe by send function */ | 
|  | spin_lock(&hc->socket_lock); | 
|  | /* if hc->socket is NULL, it is in use until it is given back */ | 
|  | while (!hc->socket) { | 
|  | spin_unlock(&hc->socket_lock); | 
|  | schedule_timeout(HZ / 10); | 
|  | spin_lock(&hc->socket_lock); | 
|  | } | 
|  | hc->socket = NULL; | 
|  | spin_unlock(&hc->socket_lock); | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: socket thread terminating\n", | 
|  | __func__); | 
|  |  | 
|  | fail: | 
|  | /* free recvbuf */ | 
|  | kfree(recvbuf); | 
|  |  | 
|  | /* close socket */ | 
|  | if (socket) | 
|  | sock_release(socket); | 
|  |  | 
|  | /* if we got killed, signal completion */ | 
|  | complete(&hc->socket_complete); | 
|  | hc->socket_thread = NULL; /* show termination of thread */ | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: socket thread terminated\n", | 
|  | __func__); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void | 
|  | l1oip_socket_close(struct l1oip *hc) | 
|  | { | 
|  | struct dchannel *dch = hc->chan[hc->d_idx].dch; | 
|  |  | 
|  | /* kill thread */ | 
|  | if (hc->socket_thread) { | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: socket thread exists, " | 
|  | "killing...\n", __func__); | 
|  | send_sig(SIGTERM, hc->socket_thread, 0); | 
|  | wait_for_completion(&hc->socket_complete); | 
|  | } | 
|  |  | 
|  | /* if active, we send up a PH_DEACTIVATE and deactivate */ | 
|  | if (test_bit(FLG_ACTIVE, &dch->Flags)) { | 
|  | if (debug & (DEBUG_L1OIP_MSG | DEBUG_L1OIP_SOCKET)) | 
|  | printk(KERN_DEBUG "%s: interface become deactivated " | 
|  | "due to timeout\n", __func__); | 
|  | test_and_clear_bit(FLG_ACTIVE, &dch->Flags); | 
|  | _queue_data(&dch->dev.D, PH_DEACTIVATE_IND, MISDN_ID_ANY, 0, | 
|  | NULL, GFP_ATOMIC); | 
|  | } | 
|  | } | 
|  |  | 
|  | static int | 
|  | l1oip_socket_open(struct l1oip *hc) | 
|  | { | 
|  | /* in case of reopen, we need to close first */ | 
|  | l1oip_socket_close(hc); | 
|  |  | 
|  | init_completion(&hc->socket_complete); | 
|  |  | 
|  | /* create receive process */ | 
|  | hc->socket_thread = kthread_run(l1oip_socket_thread, hc, "l1oip_%s", | 
|  | hc->name); | 
|  | if (IS_ERR(hc->socket_thread)) { | 
|  | int err = PTR_ERR(hc->socket_thread); | 
|  | printk(KERN_ERR "%s: Failed (%d) to create socket process.\n", | 
|  | __func__, err); | 
|  | hc->socket_thread = NULL; | 
|  | sock_release(hc->socket); | 
|  | return err; | 
|  | } | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: socket thread created\n", __func__); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  |  | 
|  | static void | 
|  | l1oip_send_bh(struct work_struct *work) | 
|  | { | 
|  | struct l1oip *hc = container_of(work, struct l1oip, workq); | 
|  |  | 
|  | if (debug & (DEBUG_L1OIP_MSG | DEBUG_L1OIP_SOCKET)) | 
|  | printk(KERN_DEBUG "%s: keepalive timer expired, sending empty " | 
|  | "frame on dchannel\n", __func__); | 
|  |  | 
|  | /* send an empty l1oip frame at D-channel */ | 
|  | l1oip_socket_send(hc, 0, hc->d_idx, 0, 0, NULL, 0); | 
|  | } | 
|  |  | 
|  |  | 
|  | /* | 
|  | * timer stuff | 
|  | */ | 
|  | static void | 
|  | l1oip_keepalive(void *data) | 
|  | { | 
|  | struct l1oip *hc = (struct l1oip *)data; | 
|  |  | 
|  | schedule_work(&hc->workq); | 
|  | } | 
|  |  | 
|  | static void | 
|  | l1oip_timeout(void *data) | 
|  | { | 
|  | struct l1oip			*hc = (struct l1oip *)data; | 
|  | struct dchannel		*dch = hc->chan[hc->d_idx].dch; | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: timeout timer expired, turn layer one " | 
|  | "down.\n", __func__); | 
|  |  | 
|  | hc->timeout_on = 0; /* state that timer must be initialized next time */ | 
|  |  | 
|  | /* if timeout, we send up a PH_DEACTIVATE and deactivate */ | 
|  | if (test_bit(FLG_ACTIVE, &dch->Flags)) { | 
|  | if (debug & (DEBUG_L1OIP_MSG | DEBUG_L1OIP_SOCKET)) | 
|  | printk(KERN_DEBUG "%s: interface become deactivated " | 
|  | "due to timeout\n", __func__); | 
|  | test_and_clear_bit(FLG_ACTIVE, &dch->Flags); | 
|  | _queue_data(&dch->dev.D, PH_DEACTIVATE_IND, MISDN_ID_ANY, 0, | 
|  | NULL, GFP_ATOMIC); | 
|  | } | 
|  |  | 
|  | /* if we have ondemand set, we remove ip address */ | 
|  | if (hc->ondemand) { | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: on demand causes ip address to " | 
|  | "be removed\n", __func__); | 
|  | hc->sin_remote.sin_addr.s_addr = 0; | 
|  | } | 
|  | } | 
|  |  | 
|  |  | 
|  | /* | 
|  | * message handling | 
|  | */ | 
|  | static int | 
|  | handle_dmsg(struct mISDNchannel *ch, struct sk_buff *skb) | 
|  | { | 
|  | struct mISDNdevice	*dev = container_of(ch, struct mISDNdevice, D); | 
|  | struct dchannel		*dch = container_of(dev, struct dchannel, dev); | 
|  | struct l1oip			*hc = dch->hw; | 
|  | struct mISDNhead	*hh = mISDN_HEAD_P(skb); | 
|  | int			ret = -EINVAL; | 
|  | int			l, ll; | 
|  | unsigned char		*p; | 
|  |  | 
|  | switch (hh->prim) { | 
|  | case PH_DATA_REQ: | 
|  | if (skb->len < 1) { | 
|  | printk(KERN_WARNING "%s: skb too small\n", | 
|  | __func__); | 
|  | break; | 
|  | } | 
|  | if (skb->len > MAX_DFRAME_LEN_L1 || skb->len > L1OIP_MAX_LEN) { | 
|  | printk(KERN_WARNING "%s: skb too large\n", | 
|  | __func__); | 
|  | break; | 
|  | } | 
|  | /* send frame */ | 
|  | p = skb->data; | 
|  | l = skb->len; | 
|  | while (l) { | 
|  | ll = (l < L1OIP_MAX_PERFRAME) ? l : L1OIP_MAX_PERFRAME; | 
|  | l1oip_socket_send(hc, 0, dch->slot, 0, | 
|  | hc->chan[dch->slot].tx_counter++, p, ll); | 
|  | p += ll; | 
|  | l -= ll; | 
|  | } | 
|  | skb_trim(skb, 0); | 
|  | queue_ch_frame(ch, PH_DATA_CNF, hh->id, skb); | 
|  | return 0; | 
|  | case PH_ACTIVATE_REQ: | 
|  | if (debug & (DEBUG_L1OIP_MSG | DEBUG_L1OIP_SOCKET)) | 
|  | printk(KERN_DEBUG "%s: PH_ACTIVATE channel %d (1..%d)\n" | 
|  | , __func__, dch->slot, hc->b_num + 1); | 
|  | skb_trim(skb, 0); | 
|  | if (test_bit(FLG_ACTIVE, &dch->Flags)) | 
|  | queue_ch_frame(ch, PH_ACTIVATE_IND, hh->id, skb); | 
|  | else | 
|  | queue_ch_frame(ch, PH_DEACTIVATE_IND, hh->id, skb); | 
|  | return 0; | 
|  | case PH_DEACTIVATE_REQ: | 
|  | if (debug & (DEBUG_L1OIP_MSG | DEBUG_L1OIP_SOCKET)) | 
|  | printk(KERN_DEBUG "%s: PH_DEACTIVATE channel %d " | 
|  | "(1..%d)\n", __func__, dch->slot, | 
|  | hc->b_num + 1); | 
|  | skb_trim(skb, 0); | 
|  | if (test_bit(FLG_ACTIVE, &dch->Flags)) | 
|  | queue_ch_frame(ch, PH_ACTIVATE_IND, hh->id, skb); | 
|  | else | 
|  | queue_ch_frame(ch, PH_DEACTIVATE_IND, hh->id, skb); | 
|  | return 0; | 
|  | } | 
|  | if (!ret) | 
|  | dev_kfree_skb(skb); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int | 
|  | channel_dctrl(struct dchannel *dch, struct mISDN_ctrl_req *cq) | 
|  | { | 
|  | int	ret = 0; | 
|  | struct l1oip	*hc = dch->hw; | 
|  |  | 
|  | switch (cq->op) { | 
|  | case MISDN_CTRL_GETOP: | 
|  | cq->op = MISDN_CTRL_SETPEER | MISDN_CTRL_UNSETPEER | 
|  | | MISDN_CTRL_GETPEER; | 
|  | break; | 
|  | case MISDN_CTRL_SETPEER: | 
|  | hc->remoteip = (u32)cq->p1; | 
|  | hc->remoteport = cq->p2 & 0xffff; | 
|  | hc->localport = cq->p2 >> 16; | 
|  | if (!hc->remoteport) | 
|  | hc->remoteport = hc->localport; | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: got new ip address from user " | 
|  | "space.\n", __func__); | 
|  | l1oip_socket_open(hc); | 
|  | break; | 
|  | case MISDN_CTRL_UNSETPEER: | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: removing ip address.\n", | 
|  | __func__); | 
|  | hc->remoteip = 0; | 
|  | l1oip_socket_open(hc); | 
|  | break; | 
|  | case MISDN_CTRL_GETPEER: | 
|  | if (debug & DEBUG_L1OIP_SOCKET) | 
|  | printk(KERN_DEBUG "%s: getting ip address.\n", | 
|  | __func__); | 
|  | cq->p1 = hc->remoteip; | 
|  | cq->p2 = hc->remoteport | (hc->localport << 16); | 
|  | break; | 
|  | default: | 
|  | printk(KERN_WARNING "%s: unknown Op %x\n", | 
|  | __func__, cq->op); | 
|  | ret = -EINVAL; | 
|  | break; | 
|  | } | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int | 
|  | open_dchannel(struct l1oip *hc, struct dchannel *dch, struct channel_req *rq) | 
|  | { | 
|  | if (debug & DEBUG_HW_OPEN) | 
|  | printk(KERN_DEBUG "%s: dev(%d) open from %p\n", __func__, | 
|  | dch->dev.id, __builtin_return_address(0)); | 
|  | if (rq->protocol == ISDN_P_NONE) | 
|  | return -EINVAL; | 
|  | if ((dch->dev.D.protocol != ISDN_P_NONE) && | 
|  | (dch->dev.D.protocol != rq->protocol)) { | 
|  | if (debug & DEBUG_HW_OPEN) | 
|  | printk(KERN_WARNING "%s: change protocol %x to %x\n", | 
|  | __func__, dch->dev.D.protocol, rq->protocol); | 
|  | } | 
|  | if (dch->dev.D.protocol != rq->protocol) | 
|  | dch->dev.D.protocol = rq->protocol; | 
|  |  | 
|  | if (test_bit(FLG_ACTIVE, &dch->Flags)) { | 
|  | _queue_data(&dch->dev.D, PH_ACTIVATE_IND, MISDN_ID_ANY, | 
|  | 0, NULL, GFP_KERNEL); | 
|  | } | 
|  | rq->ch = &dch->dev.D; | 
|  | if (!try_module_get(THIS_MODULE)) | 
|  | printk(KERN_WARNING "%s:cannot get module\n", __func__); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int | 
|  | open_bchannel(struct l1oip *hc, struct dchannel *dch, struct channel_req *rq) | 
|  | { | 
|  | struct bchannel	*bch; | 
|  | int		ch; | 
|  |  | 
|  | if (!test_channelmap(rq->adr.channel, dch->dev.channelmap)) | 
|  | return -EINVAL; | 
|  | if (rq->protocol == ISDN_P_NONE) | 
|  | return -EINVAL; | 
|  | ch = rq->adr.channel; /* BRI: 1=B1 2=B2  PRI: 1..15,17.. */ | 
|  | bch = hc->chan[ch].bch; | 
|  | if (!bch) { | 
|  | printk(KERN_ERR "%s:internal error ch %d has no bch\n", | 
|  | __func__, ch); | 
|  | return -EINVAL; | 
|  | } | 
|  | if (test_and_set_bit(FLG_OPEN, &bch->Flags)) | 
|  | return -EBUSY; /* b-channel can be only open once */ | 
|  | bch->ch.protocol = rq->protocol; | 
|  | rq->ch = &bch->ch; | 
|  | if (!try_module_get(THIS_MODULE)) | 
|  | printk(KERN_WARNING "%s:cannot get module\n", __func__); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int | 
|  | l1oip_dctrl(struct mISDNchannel *ch, u_int cmd, void *arg) | 
|  | { | 
|  | struct mISDNdevice	*dev = container_of(ch, struct mISDNdevice, D); | 
|  | struct dchannel		*dch = container_of(dev, struct dchannel, dev); | 
|  | struct l1oip			*hc = dch->hw; | 
|  | struct channel_req	*rq; | 
|  | int			err = 0; | 
|  |  | 
|  | if (dch->debug & DEBUG_HW) | 
|  | printk(KERN_DEBUG "%s: cmd:%x %p\n", | 
|  | __func__, cmd, arg); | 
|  | switch (cmd) { | 
|  | case OPEN_CHANNEL: | 
|  | rq = arg; | 
|  | switch (rq->protocol) { | 
|  | case ISDN_P_TE_S0: | 
|  | case ISDN_P_NT_S0: | 
|  | if (hc->pri) { | 
|  | err = -EINVAL; | 
|  | break; | 
|  | } | 
|  | err = open_dchannel(hc, dch, rq); | 
|  | break; | 
|  | case ISDN_P_TE_E1: | 
|  | case ISDN_P_NT_E1: | 
|  | if (!hc->pri) { | 
|  | err = -EINVAL; | 
|  | break; | 
|  | } | 
|  | err = open_dchannel(hc, dch, rq); | 
|  | break; | 
|  | default: | 
|  | err = open_bchannel(hc, dch, rq); | 
|  | } | 
|  | break; | 
|  | case CLOSE_CHANNEL: | 
|  | if (debug & DEBUG_HW_OPEN) | 
|  | printk(KERN_DEBUG "%s: dev(%d) close from %p\n", | 
|  | __func__, dch->dev.id, | 
|  | __builtin_return_address(0)); | 
|  | module_put(THIS_MODULE); | 
|  | break; | 
|  | case CONTROL_CHANNEL: | 
|  | err = channel_dctrl(dch, arg); | 
|  | break; | 
|  | default: | 
|  | if (dch->debug & DEBUG_HW) | 
|  | printk(KERN_DEBUG "%s: unknown command %x\n", | 
|  | __func__, cmd); | 
|  | err = -EINVAL; | 
|  | } | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int | 
|  | handle_bmsg(struct mISDNchannel *ch, struct sk_buff *skb) | 
|  | { | 
|  | struct bchannel		*bch = container_of(ch, struct bchannel, ch); | 
|  | struct l1oip			*hc = bch->hw; | 
|  | int			ret = -EINVAL; | 
|  | struct mISDNhead	*hh = mISDN_HEAD_P(skb); | 
|  | int			l, ll; | 
|  | unsigned char		*p; | 
|  |  | 
|  | switch (hh->prim) { | 
|  | case PH_DATA_REQ: | 
|  | if (skb->len <= 0) { | 
|  | printk(KERN_WARNING "%s: skb too small\n", | 
|  | __func__); | 
|  | break; | 
|  | } | 
|  | if (skb->len > MAX_DFRAME_LEN_L1 || skb->len > L1OIP_MAX_LEN) { | 
|  | printk(KERN_WARNING "%s: skb too large\n", | 
|  | __func__); | 
|  | break; | 
|  | } | 
|  | /* check for AIS / ulaw-silence */ | 
|  | l = skb->len; | 
|  | if (!memchr_inv(skb->data, 0xff, l)) { | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: got AIS, not sending, " | 
|  | "but counting\n", __func__); | 
|  | hc->chan[bch->slot].tx_counter += l; | 
|  | skb_trim(skb, 0); | 
|  | queue_ch_frame(ch, PH_DATA_CNF, hh->id, skb); | 
|  | return 0; | 
|  | } | 
|  | /* check for silence */ | 
|  | l = skb->len; | 
|  | if (!memchr_inv(skb->data, 0x2a, l)) { | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: got silence, not sending" | 
|  | ", but counting\n", __func__); | 
|  | hc->chan[bch->slot].tx_counter += l; | 
|  | skb_trim(skb, 0); | 
|  | queue_ch_frame(ch, PH_DATA_CNF, hh->id, skb); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* send frame */ | 
|  | p = skb->data; | 
|  | l = skb->len; | 
|  | while (l) { | 
|  | ll = (l < L1OIP_MAX_PERFRAME) ? l : L1OIP_MAX_PERFRAME; | 
|  | l1oip_socket_send(hc, hc->codec, bch->slot, 0, | 
|  | hc->chan[bch->slot].tx_counter, p, ll); | 
|  | hc->chan[bch->slot].tx_counter += ll; | 
|  | p += ll; | 
|  | l -= ll; | 
|  | } | 
|  | skb_trim(skb, 0); | 
|  | queue_ch_frame(ch, PH_DATA_CNF, hh->id, skb); | 
|  | return 0; | 
|  | case PH_ACTIVATE_REQ: | 
|  | if (debug & (DEBUG_L1OIP_MSG | DEBUG_L1OIP_SOCKET)) | 
|  | printk(KERN_DEBUG "%s: PH_ACTIVATE channel %d (1..%d)\n" | 
|  | , __func__, bch->slot, hc->b_num + 1); | 
|  | hc->chan[bch->slot].codecstate = 0; | 
|  | test_and_set_bit(FLG_ACTIVE, &bch->Flags); | 
|  | skb_trim(skb, 0); | 
|  | queue_ch_frame(ch, PH_ACTIVATE_IND, hh->id, skb); | 
|  | return 0; | 
|  | case PH_DEACTIVATE_REQ: | 
|  | if (debug & (DEBUG_L1OIP_MSG | DEBUG_L1OIP_SOCKET)) | 
|  | printk(KERN_DEBUG "%s: PH_DEACTIVATE channel %d " | 
|  | "(1..%d)\n", __func__, bch->slot, | 
|  | hc->b_num + 1); | 
|  | test_and_clear_bit(FLG_ACTIVE, &bch->Flags); | 
|  | skb_trim(skb, 0); | 
|  | queue_ch_frame(ch, PH_DEACTIVATE_IND, hh->id, skb); | 
|  | return 0; | 
|  | } | 
|  | if (!ret) | 
|  | dev_kfree_skb(skb); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int | 
|  | channel_bctrl(struct bchannel *bch, struct mISDN_ctrl_req *cq) | 
|  | { | 
|  | int			ret = 0; | 
|  | struct dsp_features	*features = | 
|  | (struct dsp_features *)(*((u_long *)&cq->p1)); | 
|  |  | 
|  | switch (cq->op) { | 
|  | case MISDN_CTRL_GETOP: | 
|  | cq->op = MISDN_CTRL_HW_FEATURES_OP; | 
|  | break; | 
|  | case MISDN_CTRL_HW_FEATURES: /* fill features structure */ | 
|  | if (debug & DEBUG_L1OIP_MSG) | 
|  | printk(KERN_DEBUG "%s: HW_FEATURE request\n", | 
|  | __func__); | 
|  | /* create confirm */ | 
|  | features->unclocked = 1; | 
|  | features->unordered = 1; | 
|  | break; | 
|  | default: | 
|  | printk(KERN_WARNING "%s: unknown Op %x\n", | 
|  | __func__, cq->op); | 
|  | ret = -EINVAL; | 
|  | break; | 
|  | } | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int | 
|  | l1oip_bctrl(struct mISDNchannel *ch, u_int cmd, void *arg) | 
|  | { | 
|  | struct bchannel	*bch = container_of(ch, struct bchannel, ch); | 
|  | int		err = -EINVAL; | 
|  |  | 
|  | if (bch->debug & DEBUG_HW) | 
|  | printk(KERN_DEBUG "%s: cmd:%x %p\n", | 
|  | __func__, cmd, arg); | 
|  | switch (cmd) { | 
|  | case CLOSE_CHANNEL: | 
|  | test_and_clear_bit(FLG_OPEN, &bch->Flags); | 
|  | test_and_clear_bit(FLG_ACTIVE, &bch->Flags); | 
|  | ch->protocol = ISDN_P_NONE; | 
|  | ch->peer = NULL; | 
|  | module_put(THIS_MODULE); | 
|  | err = 0; | 
|  | break; | 
|  | case CONTROL_CHANNEL: | 
|  | err = channel_bctrl(bch, arg); | 
|  | break; | 
|  | default: | 
|  | printk(KERN_WARNING "%s: unknown prim(%x)\n", | 
|  | __func__, cmd); | 
|  | } | 
|  | return err; | 
|  | } | 
|  |  | 
|  |  | 
|  | /* | 
|  | * cleanup module and stack | 
|  | */ | 
|  | static void | 
|  | release_card(struct l1oip *hc) | 
|  | { | 
|  | int	ch; | 
|  |  | 
|  | if (timer_pending(&hc->keep_tl)) | 
|  | del_timer(&hc->keep_tl); | 
|  |  | 
|  | if (timer_pending(&hc->timeout_tl)) | 
|  | del_timer(&hc->timeout_tl); | 
|  |  | 
|  | cancel_work_sync(&hc->workq); | 
|  |  | 
|  | if (hc->socket_thread) | 
|  | l1oip_socket_close(hc); | 
|  |  | 
|  | if (hc->registered && hc->chan[hc->d_idx].dch) | 
|  | mISDN_unregister_device(&hc->chan[hc->d_idx].dch->dev); | 
|  | for (ch = 0; ch < 128; ch++) { | 
|  | if (hc->chan[ch].dch) { | 
|  | mISDN_freedchannel(hc->chan[ch].dch); | 
|  | kfree(hc->chan[ch].dch); | 
|  | } | 
|  | if (hc->chan[ch].bch) { | 
|  | mISDN_freebchannel(hc->chan[ch].bch); | 
|  | kfree(hc->chan[ch].bch); | 
|  | #ifdef REORDER_DEBUG | 
|  | if (hc->chan[ch].disorder_skb) | 
|  | dev_kfree_skb(hc->chan[ch].disorder_skb); | 
|  | #endif | 
|  | } | 
|  | } | 
|  |  | 
|  | spin_lock(&l1oip_lock); | 
|  | list_del(&hc->list); | 
|  | spin_unlock(&l1oip_lock); | 
|  |  | 
|  | kfree(hc); | 
|  | } | 
|  |  | 
|  | static void | 
|  | l1oip_cleanup(void) | 
|  | { | 
|  | struct l1oip *hc, *next; | 
|  |  | 
|  | list_for_each_entry_safe(hc, next, &l1oip_ilist, list) | 
|  | release_card(hc); | 
|  |  | 
|  | l1oip_4bit_free(); | 
|  | } | 
|  |  | 
|  |  | 
|  | /* | 
|  | * module and stack init | 
|  | */ | 
|  | static int | 
|  | init_card(struct l1oip *hc, int pri, int bundle) | 
|  | { | 
|  | struct dchannel	*dch; | 
|  | struct bchannel	*bch; | 
|  | int		ret; | 
|  | int		i, ch; | 
|  |  | 
|  | spin_lock_init(&hc->socket_lock); | 
|  | hc->idx = l1oip_cnt; | 
|  | hc->pri = pri; | 
|  | hc->d_idx = pri ? 16 : 3; | 
|  | hc->b_num = pri ? 30 : 2; | 
|  | hc->bundle = bundle; | 
|  | if (hc->pri) | 
|  | sprintf(hc->name, "l1oip-e1.%d", l1oip_cnt + 1); | 
|  | else | 
|  | sprintf(hc->name, "l1oip-s0.%d", l1oip_cnt + 1); | 
|  |  | 
|  | switch (codec[l1oip_cnt]) { | 
|  | case 0: /* as is */ | 
|  | case 1: /* alaw */ | 
|  | case 2: /* ulaw */ | 
|  | case 3: /* 4bit */ | 
|  | break; | 
|  | default: | 
|  | printk(KERN_ERR "Codec(%d) not supported.\n", | 
|  | codec[l1oip_cnt]); | 
|  | return -EINVAL; | 
|  | } | 
|  | hc->codec = codec[l1oip_cnt]; | 
|  | if (debug & DEBUG_L1OIP_INIT) | 
|  | printk(KERN_DEBUG "%s: using codec %d\n", | 
|  | __func__, hc->codec); | 
|  |  | 
|  | if (id[l1oip_cnt] == 0) { | 
|  | printk(KERN_WARNING "Warning: No 'id' value given or " | 
|  | "0, this is highly unsecure. Please use 32 " | 
|  | "bit randmom number 0x...\n"); | 
|  | } | 
|  | hc->id = id[l1oip_cnt]; | 
|  | if (debug & DEBUG_L1OIP_INIT) | 
|  | printk(KERN_DEBUG "%s: using id 0x%x\n", __func__, hc->id); | 
|  |  | 
|  | hc->ondemand = ondemand[l1oip_cnt]; | 
|  | if (hc->ondemand && !hc->id) { | 
|  | printk(KERN_ERR "%s: ondemand option only allowed in " | 
|  | "conjunction with non 0 ID\n", __func__); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | if (limit[l1oip_cnt]) | 
|  | hc->b_num = limit[l1oip_cnt]; | 
|  | if (!pri && hc->b_num > 2) { | 
|  | printk(KERN_ERR "Maximum limit for BRI interface is 2 " | 
|  | "channels.\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  | if (pri && hc->b_num > 126) { | 
|  | printk(KERN_ERR "Maximum limit for PRI interface is 126 " | 
|  | "channels.\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  | if (pri && hc->b_num > 30) { | 
|  | printk(KERN_WARNING "Maximum limit for BRI interface is 30 " | 
|  | "channels.\n"); | 
|  | printk(KERN_WARNING "Your selection of %d channels must be " | 
|  | "supported by application.\n", hc->limit); | 
|  | } | 
|  |  | 
|  | hc->remoteip = ip[l1oip_cnt << 2] << 24 | 
|  | | ip[(l1oip_cnt << 2) + 1] << 16 | 
|  | | ip[(l1oip_cnt << 2) + 2] << 8 | 
|  | | ip[(l1oip_cnt << 2) + 3]; | 
|  | hc->localport = port[l1oip_cnt]?:(L1OIP_DEFAULTPORT + l1oip_cnt); | 
|  | if (remoteport[l1oip_cnt]) | 
|  | hc->remoteport = remoteport[l1oip_cnt]; | 
|  | else | 
|  | hc->remoteport = hc->localport; | 
|  | if (debug & DEBUG_L1OIP_INIT) | 
|  | printk(KERN_DEBUG "%s: using local port %d remote ip " | 
|  | "%d.%d.%d.%d port %d ondemand %d\n", __func__, | 
|  | hc->localport, hc->remoteip >> 24, | 
|  | (hc->remoteip >> 16) & 0xff, | 
|  | (hc->remoteip >> 8) & 0xff, hc->remoteip & 0xff, | 
|  | hc->remoteport, hc->ondemand); | 
|  |  | 
|  | dch = kzalloc(sizeof(struct dchannel), GFP_KERNEL); | 
|  | if (!dch) | 
|  | return -ENOMEM; | 
|  | dch->debug = debug; | 
|  | mISDN_initdchannel(dch, MAX_DFRAME_LEN_L1, NULL); | 
|  | dch->hw = hc; | 
|  | if (pri) | 
|  | dch->dev.Dprotocols = (1 << ISDN_P_TE_E1) | (1 << ISDN_P_NT_E1); | 
|  | else | 
|  | dch->dev.Dprotocols = (1 << ISDN_P_TE_S0) | (1 << ISDN_P_NT_S0); | 
|  | dch->dev.Bprotocols = (1 << (ISDN_P_B_RAW & ISDN_P_B_MASK)) | | 
|  | (1 << (ISDN_P_B_HDLC & ISDN_P_B_MASK)); | 
|  | dch->dev.D.send = handle_dmsg; | 
|  | dch->dev.D.ctrl = l1oip_dctrl; | 
|  | dch->dev.nrbchan = hc->b_num; | 
|  | dch->slot = hc->d_idx; | 
|  | hc->chan[hc->d_idx].dch = dch; | 
|  | i = 1; | 
|  | for (ch = 0; ch < dch->dev.nrbchan; ch++) { | 
|  | if (ch == 15) | 
|  | i++; | 
|  | bch = kzalloc(sizeof(struct bchannel), GFP_KERNEL); | 
|  | if (!bch) { | 
|  | printk(KERN_ERR "%s: no memory for bchannel\n", | 
|  | __func__); | 
|  | return -ENOMEM; | 
|  | } | 
|  | bch->nr = i + ch; | 
|  | bch->slot = i + ch; | 
|  | bch->debug = debug; | 
|  | mISDN_initbchannel(bch, MAX_DATA_MEM, 0); | 
|  | bch->hw = hc; | 
|  | bch->ch.send = handle_bmsg; | 
|  | bch->ch.ctrl = l1oip_bctrl; | 
|  | bch->ch.nr = i + ch; | 
|  | list_add(&bch->ch.list, &dch->dev.bchannels); | 
|  | hc->chan[i + ch].bch = bch; | 
|  | set_channelmap(bch->nr, dch->dev.channelmap); | 
|  | } | 
|  | /* TODO: create a parent device for this driver */ | 
|  | ret = mISDN_register_device(&dch->dev, NULL, hc->name); | 
|  | if (ret) | 
|  | return ret; | 
|  | hc->registered = 1; | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_INIT) | 
|  | printk(KERN_DEBUG "%s: Setting up network card(%d)\n", | 
|  | __func__, l1oip_cnt + 1); | 
|  | ret = l1oip_socket_open(hc); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | hc->keep_tl.function = (void *)l1oip_keepalive; | 
|  | hc->keep_tl.data = (ulong)hc; | 
|  | init_timer(&hc->keep_tl); | 
|  | hc->keep_tl.expires = jiffies + 2 * HZ; /* two seconds first time */ | 
|  | add_timer(&hc->keep_tl); | 
|  |  | 
|  | hc->timeout_tl.function = (void *)l1oip_timeout; | 
|  | hc->timeout_tl.data = (ulong)hc; | 
|  | init_timer(&hc->timeout_tl); | 
|  | hc->timeout_on = 0; /* state that we have timer off */ | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int __init | 
|  | l1oip_init(void) | 
|  | { | 
|  | int		pri, bundle; | 
|  | struct l1oip		*hc; | 
|  | int		ret; | 
|  |  | 
|  | printk(KERN_INFO "mISDN: Layer-1-over-IP driver Rev. %s\n", | 
|  | l1oip_revision); | 
|  |  | 
|  | INIT_LIST_HEAD(&l1oip_ilist); | 
|  | spin_lock_init(&l1oip_lock); | 
|  |  | 
|  | if (l1oip_4bit_alloc(ulaw)) | 
|  | return -ENOMEM; | 
|  |  | 
|  | l1oip_cnt = 0; | 
|  | while (l1oip_cnt < MAX_CARDS && type[l1oip_cnt]) { | 
|  | switch (type[l1oip_cnt] & 0xff) { | 
|  | case 1: | 
|  | pri = 0; | 
|  | bundle = 0; | 
|  | break; | 
|  | case 2: | 
|  | pri = 1; | 
|  | bundle = 0; | 
|  | break; | 
|  | case 3: | 
|  | pri = 0; | 
|  | bundle = 1; | 
|  | break; | 
|  | case 4: | 
|  | pri = 1; | 
|  | bundle = 1; | 
|  | break; | 
|  | default: | 
|  | printk(KERN_ERR "Card type(%d) not supported.\n", | 
|  | type[l1oip_cnt] & 0xff); | 
|  | l1oip_cleanup(); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | if (debug & DEBUG_L1OIP_INIT) | 
|  | printk(KERN_DEBUG "%s: interface %d is %s with %s.\n", | 
|  | __func__, l1oip_cnt, pri ? "PRI" : "BRI", | 
|  | bundle ? "bundled IP packet for all B-channels" : | 
|  | "separate IP packets for every B-channel"); | 
|  |  | 
|  | hc = kzalloc(sizeof(struct l1oip), GFP_ATOMIC); | 
|  | if (!hc) { | 
|  | printk(KERN_ERR "No kmem for L1-over-IP driver.\n"); | 
|  | l1oip_cleanup(); | 
|  | return -ENOMEM; | 
|  | } | 
|  | INIT_WORK(&hc->workq, (void *)l1oip_send_bh); | 
|  |  | 
|  | spin_lock(&l1oip_lock); | 
|  | list_add_tail(&hc->list, &l1oip_ilist); | 
|  | spin_unlock(&l1oip_lock); | 
|  |  | 
|  | ret = init_card(hc, pri, bundle); | 
|  | if (ret) { | 
|  | l1oip_cleanup(); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | l1oip_cnt++; | 
|  | } | 
|  | printk(KERN_INFO "%d virtual devices registered\n", l1oip_cnt); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | module_init(l1oip_init); | 
|  | module_exit(l1oip_cleanup); |