blob: df0e9ffff7067e86c158e587028f6e250ba6643a [file] [log] [blame]
/******************************************************************************
*
* This file is provided under a dual BSD/GPLv2 license. When using or
* redistributing this file, you may do so under either license.
*
* GPL LICENSE SUMMARY
*
* Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
* Copyright(c) 2015 - 2017 Intel Deutschland GmbH
* Copyright(c) 2018 Intel Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program.
*
* The full GNU General Public License is included in this distribution
* in the file called COPYING.
*
* Contact Information:
* Intel Linux Wireless <linuxwifi@intel.com>
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*
* BSD LICENSE
*
* Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
* Copyright(c) 2015 - 2017 Intel Deutschland GmbH
* Copyright(c) 2018 Intel Corporation
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name Intel Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*****************************************************************************/
#ifndef __iwl_fh_h__
#define __iwl_fh_h__
#include <linux/types.h>
#include <linux/bitfield.h>
/****************************/
/* Flow Handler Definitions */
/****************************/
/**
* This I/O area is directly read/writable by driver (e.g. Linux uses writel())
* Addresses are offsets from device's PCI hardware base address.
*/
#define FH_MEM_LOWER_BOUND (0x1000)
#define FH_MEM_UPPER_BOUND (0x2000)
#define FH_MEM_LOWER_BOUND_GEN2 (0xa06000)
#define FH_MEM_UPPER_BOUND_GEN2 (0xa08000)
/**
* Keep-Warm (KW) buffer base address.
*
* Driver must allocate a 4KByte buffer that is for keeping the
* host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency
* DRAM access when doing Txing or Rxing. The dummy accesses prevent host
* from going into a power-savings mode that would cause higher DRAM latency,
* and possible data over/under-runs, before all Tx/Rx is complete.
*
* Driver loads FH_KW_MEM_ADDR_REG with the physical address (bits 35:4)
* of the buffer, which must be 4K aligned. Once this is set up, the device
* automatically invokes keep-warm accesses when normal accesses might not
* be sufficient to maintain fast DRAM response.
*
* Bit fields:
* 31-0: Keep-warm buffer physical base address [35:4], must be 4K aligned
*/
#define FH_KW_MEM_ADDR_REG (FH_MEM_LOWER_BOUND + 0x97C)
/**
* TFD Circular Buffers Base (CBBC) addresses
*
* Device has 16 base pointer registers, one for each of 16 host-DRAM-resident
* circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs)
* (see struct iwl_tfd_frame). These 16 pointer registers are offset by 0x04
* bytes from one another. Each TFD circular buffer in DRAM must be 256-byte
* aligned (address bits 0-7 must be 0).
* Later devices have 20 (5000 series) or 30 (higher) queues, but the registers
* for them are in different places.
*
* Bit fields in each pointer register:
* 27-0: TFD CB physical base address [35:8], must be 256-byte aligned
*/
#define FH_MEM_CBBC_0_15_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x9D0)
#define FH_MEM_CBBC_0_15_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xA10)
#define FH_MEM_CBBC_16_19_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xBF0)
#define FH_MEM_CBBC_16_19_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_CBBC_20_31_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xB20)
#define FH_MEM_CBBC_20_31_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xB80)
/* 22000 TFD table address, 64 bit */
#define TFH_TFDQ_CBB_TABLE (0x1C00)
/* Find TFD CB base pointer for given queue */
static inline unsigned int FH_MEM_CBBC_QUEUE(struct iwl_trans *trans,
unsigned int chnl)
{
if (trans->cfg->use_tfh) {
WARN_ON_ONCE(chnl >= 64);
return TFH_TFDQ_CBB_TABLE + 8 * chnl;
}
if (chnl < 16)
return FH_MEM_CBBC_0_15_LOWER_BOUND + 4 * chnl;
if (chnl < 20)
return FH_MEM_CBBC_16_19_LOWER_BOUND + 4 * (chnl - 16);
WARN_ON_ONCE(chnl >= 32);
return FH_MEM_CBBC_20_31_LOWER_BOUND + 4 * (chnl - 20);
}
/* 22000 configuration registers */
/*
* TFH Configuration register.
*
* BIT fields:
*
* Bits 3:0:
* Define the maximum number of pending read requests.
* Maximum configration value allowed is 0xC
* Bits 9:8:
* Define the maximum transfer size. (64 / 128 / 256)
* Bit 10:
* When bit is set and transfer size is set to 128B, the TFH will enable
* reading chunks of more than 64B only if the read address is aligned to 128B.
* In case of DRAM read address which is not aligned to 128B, the TFH will
* enable transfer size which doesn't cross 64B DRAM address boundary.
*/
#define TFH_TRANSFER_MODE (0x1F40)
#define TFH_TRANSFER_MAX_PENDING_REQ 0xc
#define TFH_CHUNK_SIZE_128 BIT(8)
#define TFH_CHUNK_SPLIT_MODE BIT(10)
/*
* Defines the offset address in dwords referring from the beginning of the
* Tx CMD which will be updated in DRAM.
* Note that the TFH offset address for Tx CMD update is always referring to
* the start of the TFD first TB.
* In case of a DRAM Tx CMD update the TFH will update PN and Key ID
*/
#define TFH_TXCMD_UPDATE_CFG (0x1F48)
/*
* Controls TX DMA operation
*
* BIT fields:
*
* Bits 31:30: Enable the SRAM DMA channel.
* Turning on bit 31 will kick the SRAM2DRAM DMA.
* Note that the sram2dram may be enabled only after configuring the DRAM and
* SRAM addresses registers and the byte count register.
* Bits 25:24: Defines the interrupt target upon dram2sram transfer done. When
* set to 1 - interrupt is sent to the driver
* Bit 0: Indicates the snoop configuration
*/
#define TFH_SRV_DMA_CHNL0_CTRL (0x1F60)
#define TFH_SRV_DMA_SNOOP BIT(0)
#define TFH_SRV_DMA_TO_DRIVER BIT(24)
#define TFH_SRV_DMA_START BIT(31)
/* Defines the DMA SRAM write start address to transfer a data block */
#define TFH_SRV_DMA_CHNL0_SRAM_ADDR (0x1F64)
/* Defines the 64bits DRAM start address to read the DMA data block from */
#define TFH_SRV_DMA_CHNL0_DRAM_ADDR (0x1F68)
/*
* Defines the number of bytes to transfer from DRAM to SRAM.
* Note that this register may be configured with non-dword aligned size.
*/
#define TFH_SRV_DMA_CHNL0_BC (0x1F70)
/**
* Rx SRAM Control and Status Registers (RSCSR)
*
* These registers provide handshake between driver and device for the Rx queue
* (this queue handles *all* command responses, notifications, Rx data, etc.
* sent from uCode to host driver). Unlike Tx, there is only one Rx
* queue, and only one Rx DMA/FIFO channel. Also unlike Tx, which can
* concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer
* Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1
* mapping between RBDs and RBs.
*
* Driver must allocate host DRAM memory for the following, and set the
* physical address of each into device registers:
*
* 1) Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256
* entries (although any power of 2, up to 4096, is selectable by driver).
* Each entry (1 dword) points to a receive buffer (RB) of consistent size
* (typically 4K, although 8K or 16K are also selectable by driver).
* Driver sets up RB size and number of RBDs in the CB via Rx config
* register FH_MEM_RCSR_CHNL0_CONFIG_REG.
*
* Bit fields within one RBD:
* 27-0: Receive Buffer physical address bits [35:8], 256-byte aligned
*
* Driver sets physical address [35:8] of base of RBD circular buffer
* into FH_RSCSR_CHNL0_RBDCB_BASE_REG [27:0].
*
* 2) Rx status buffer, 8 bytes, in which uCode indicates which Rx Buffers
* (RBs) have been filled, via a "write pointer", actually the index of
* the RB's corresponding RBD within the circular buffer. Driver sets
* physical address [35:4] into FH_RSCSR_CHNL0_STTS_WPTR_REG [31:0].
*
* Bit fields in lower dword of Rx status buffer (upper dword not used
* by driver:
* 31-12: Not used by driver
* 11- 0: Index of last filled Rx buffer descriptor
* (device writes, driver reads this value)
*
* As the driver prepares Receive Buffers (RBs) for device to fill, driver must
* enter pointers to these RBs into contiguous RBD circular buffer entries,
* and update the device's "write" index register,
* FH_RSCSR_CHNL0_RBDCB_WPTR_REG.
*
* This "write" index corresponds to the *next* RBD that the driver will make
* available, i.e. one RBD past the tail of the ready-to-fill RBDs within
* the circular buffer. This value should initially be 0 (before preparing any
* RBs), should be 8 after preparing the first 8 RBs (for example), and must
* wrap back to 0 at the end of the circular buffer (but don't wrap before
* "read" index has advanced past 1! See below).
* NOTE: DEVICE EXPECTS THE WRITE INDEX TO BE INCREMENTED IN MULTIPLES OF 8.
*
* As the device fills RBs (referenced from contiguous RBDs within the circular
* buffer), it updates the Rx status buffer in host DRAM, 2) described above,
* to tell the driver the index of the latest filled RBD. The driver must
* read this "read" index from DRAM after receiving an Rx interrupt from device
*
* The driver must also internally keep track of a third index, which is the
* next RBD to process. When receiving an Rx interrupt, driver should process
* all filled but unprocessed RBs up to, but not including, the RB
* corresponding to the "read" index. For example, if "read" index becomes "1",
* driver may process the RB pointed to by RBD 0. Depending on volume of
* traffic, there may be many RBs to process.
*
* If read index == write index, device thinks there is no room to put new data.
* Due to this, the maximum number of filled RBs is 255, instead of 256. To
* be safe, make sure that there is a gap of at least 2 RBDs between "write"
* and "read" indexes; that is, make sure that there are no more than 254
* buffers waiting to be filled.
*/
#define FH_MEM_RSCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xBC0)
#define FH_MEM_RSCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_RSCSR_CHNL0 (FH_MEM_RSCSR_LOWER_BOUND)
/**
* Physical base address of 8-byte Rx Status buffer.
* Bit fields:
* 31-0: Rx status buffer physical base address [35:4], must 16-byte aligned.
*/
#define FH_RSCSR_CHNL0_STTS_WPTR_REG (FH_MEM_RSCSR_CHNL0)
/**
* Physical base address of Rx Buffer Descriptor Circular Buffer.
* Bit fields:
* 27-0: RBD CD physical base address [35:8], must be 256-byte aligned.
*/
#define FH_RSCSR_CHNL0_RBDCB_BASE_REG (FH_MEM_RSCSR_CHNL0 + 0x004)
/**
* Rx write pointer (index, really!).
* Bit fields:
* 11-0: Index of driver's most recent prepared-to-be-filled RBD, + 1.
* NOTE: For 256-entry circular buffer, use only bits [7:0].
*/
#define FH_RSCSR_CHNL0_RBDCB_WPTR_REG (FH_MEM_RSCSR_CHNL0 + 0x008)
#define FH_RSCSR_CHNL0_WPTR (FH_RSCSR_CHNL0_RBDCB_WPTR_REG)
#define FW_RSCSR_CHNL0_RXDCB_RDPTR_REG (FH_MEM_RSCSR_CHNL0 + 0x00c)
#define FH_RSCSR_CHNL0_RDPTR FW_RSCSR_CHNL0_RXDCB_RDPTR_REG
/**
* Rx Config/Status Registers (RCSR)
* Rx Config Reg for channel 0 (only channel used)
*
* Driver must initialize FH_MEM_RCSR_CHNL0_CONFIG_REG as follows for
* normal operation (see bit fields).
*
* Clearing FH_MEM_RCSR_CHNL0_CONFIG_REG to 0 turns off Rx DMA.
* Driver should poll FH_MEM_RSSR_RX_STATUS_REG for
* FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (bit 24) before continuing.
*
* Bit fields:
* 31-30: Rx DMA channel enable: '00' off/pause, '01' pause at end of frame,
* '10' operate normally
* 29-24: reserved
* 23-20: # RBDs in circular buffer = 2^value; use "8" for 256 RBDs (normal),
* min "5" for 32 RBDs, max "12" for 4096 RBDs.
* 19-18: reserved
* 17-16: size of each receive buffer; '00' 4K (normal), '01' 8K,
* '10' 12K, '11' 16K.
* 15-14: reserved
* 13-12: IRQ destination; '00' none, '01' host driver (normal operation)
* 11- 4: timeout for closing Rx buffer and interrupting host (units 32 usec)
* typical value 0x10 (about 1/2 msec)
* 3- 0: reserved
*/
#define FH_MEM_RCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_RCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xCC0)
#define FH_MEM_RCSR_CHNL0 (FH_MEM_RCSR_LOWER_BOUND)
#define FH_MEM_RCSR_CHNL0_CONFIG_REG (FH_MEM_RCSR_CHNL0)
#define FH_MEM_RCSR_CHNL0_RBDCB_WPTR (FH_MEM_RCSR_CHNL0 + 0x8)
#define FH_MEM_RCSR_CHNL0_FLUSH_RB_REQ (FH_MEM_RCSR_CHNL0 + 0x10)
#define FH_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MSK (0x00000FF0) /* bits 4-11 */
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MSK (0x00001000) /* bits 12 */
#define FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MSK (0x00008000) /* bit 15 */
#define FH_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MSK (0x00030000) /* bits 16-17 */
#define FH_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MSK (0x00F00000) /* bits 20-23 */
#define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MSK (0xC0000000) /* bits 30-31*/
#define FH_RCSR_RX_CONFIG_RBDCB_SIZE_POS (20)
#define FH_RCSR_RX_CONFIG_REG_IRQ_RBTH_POS (4)
#define RX_RB_TIMEOUT (0x11)
#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000)
#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000)
#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K (0x00010000)
#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_12K (0x00020000)
#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_16K (0x00030000)
#define FH_RCSR_CHNL0_RX_IGNORE_RXF_EMPTY (0x00000004)
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000)
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000)
/**
* Rx Shared Status Registers (RSSR)
*
* After stopping Rx DMA channel (writing 0 to
* FH_MEM_RCSR_CHNL0_CONFIG_REG), driver must poll
* FH_MEM_RSSR_RX_STATUS_REG until Rx channel is idle.
*
* Bit fields:
* 24: 1 = Channel 0 is idle
*
* FH_MEM_RSSR_SHARED_CTRL_REG and FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV
* contain default values that should not be altered by the driver.
*/
#define FH_MEM_RSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC40)
#define FH_MEM_RSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xD00)
#define FH_MEM_RSSR_SHARED_CTRL_REG (FH_MEM_RSSR_LOWER_BOUND)
#define FH_MEM_RSSR_RX_STATUS_REG (FH_MEM_RSSR_LOWER_BOUND + 0x004)
#define FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV\
(FH_MEM_RSSR_LOWER_BOUND + 0x008)
#define FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (0x01000000)
#define FH_MEM_TFDIB_REG1_ADDR_BITSHIFT 28
#define FH_MEM_TB_MAX_LENGTH (0x00020000)
/* 9000 rx series registers */
#define RFH_Q0_FRBDCB_BA_LSB 0xA08000 /* 64 bit address */
#define RFH_Q_FRBDCB_BA_LSB(q) (RFH_Q0_FRBDCB_BA_LSB + (q) * 8)
/* Write index table */
#define RFH_Q0_FRBDCB_WIDX 0xA08080
#define RFH_Q_FRBDCB_WIDX(q) (RFH_Q0_FRBDCB_WIDX + (q) * 4)
/* Write index table - shadow registers */
#define RFH_Q0_FRBDCB_WIDX_TRG 0x1C80
#define RFH_Q_FRBDCB_WIDX_TRG(q) (RFH_Q0_FRBDCB_WIDX_TRG + (q) * 4)
/* Read index table */
#define RFH_Q0_FRBDCB_RIDX 0xA080C0
#define RFH_Q_FRBDCB_RIDX(q) (RFH_Q0_FRBDCB_RIDX + (q) * 4)
/* Used list table */
#define RFH_Q0_URBDCB_BA_LSB 0xA08100 /* 64 bit address */
#define RFH_Q_URBDCB_BA_LSB(q) (RFH_Q0_URBDCB_BA_LSB + (q) * 8)
/* Write index table */
#define RFH_Q0_URBDCB_WIDX 0xA08180
#define RFH_Q_URBDCB_WIDX(q) (RFH_Q0_URBDCB_WIDX + (q) * 4)
#define RFH_Q0_URBDCB_VAID 0xA081C0
#define RFH_Q_URBDCB_VAID(q) (RFH_Q0_URBDCB_VAID + (q) * 4)
/* stts */
#define RFH_Q0_URBD_STTS_WPTR_LSB 0xA08200 /*64 bits address */
#define RFH_Q_URBD_STTS_WPTR_LSB(q) (RFH_Q0_URBD_STTS_WPTR_LSB + (q) * 8)
#define RFH_Q0_ORB_WPTR_LSB 0xA08280
#define RFH_Q_ORB_WPTR_LSB(q) (RFH_Q0_ORB_WPTR_LSB + (q) * 8)
#define RFH_RBDBUF_RBD0_LSB 0xA08300
#define RFH_RBDBUF_RBD_LSB(q) (RFH_RBDBUF_RBD0_LSB + (q) * 8)
/**
* RFH Status Register
*
* Bit fields:
*
* Bit 29: RBD_FETCH_IDLE
* This status flag is set by the RFH when there is no active RBD fetch from
* DRAM.
* Once the RFH RBD controller starts fetching (or when there is a pending
* RBD read response from DRAM), this flag is immediately turned off.
*
* Bit 30: SRAM_DMA_IDLE
* This status flag is set by the RFH when there is no active transaction from
* SRAM to DRAM.
* Once the SRAM to DRAM DMA is active, this flag is immediately turned off.
*
* Bit 31: RXF_DMA_IDLE
* This status flag is set by the RFH when there is no active transaction from
* RXF to DRAM.
* Once the RXF-to-DRAM DMA is active, this flag is immediately turned off.
*/
#define RFH_GEN_STATUS 0xA09808
#define RFH_GEN_STATUS_GEN3 0xA07824
#define RBD_FETCH_IDLE BIT(29)
#define SRAM_DMA_IDLE BIT(30)
#define RXF_DMA_IDLE BIT(31)
/* DMA configuration */
#define RFH_RXF_DMA_CFG 0xA09820
#define RFH_RXF_DMA_CFG_GEN3 0xA07880
/* RB size */
#define RFH_RXF_DMA_RB_SIZE_MASK (0x000F0000) /* bits 16-19 */
#define RFH_RXF_DMA_RB_SIZE_POS 16
#define RFH_RXF_DMA_RB_SIZE_1K (0x1 << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_2K (0x2 << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_4K (0x4 << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_8K (0x8 << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_12K (0x9 << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_16K (0xA << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_20K (0xB << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_24K (0xC << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_28K (0xD << RFH_RXF_DMA_RB_SIZE_POS)
#define RFH_RXF_DMA_RB_SIZE_32K (0xE << RFH_RXF_DMA_RB_SIZE_POS)
/* RB Circular Buffer size:defines the table sizes in RBD units */
#define RFH_RXF_DMA_RBDCB_SIZE_MASK (0x00F00000) /* bits 20-23 */
#define RFH_RXF_DMA_RBDCB_SIZE_POS 20
#define RFH_RXF_DMA_RBDCB_SIZE_8 (0x3 << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_RBDCB_SIZE_16 (0x4 << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_RBDCB_SIZE_32 (0x5 << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_RBDCB_SIZE_64 (0x7 << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_RBDCB_SIZE_128 (0x7 << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_RBDCB_SIZE_256 (0x8 << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_RBDCB_SIZE_512 (0x9 << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_RBDCB_SIZE_1024 (0xA << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_RBDCB_SIZE_2048 (0xB << RFH_RXF_DMA_RBDCB_SIZE_POS)
#define RFH_RXF_DMA_MIN_RB_SIZE_MASK (0x03000000) /* bit 24-25 */
#define RFH_RXF_DMA_MIN_RB_SIZE_POS 24
#define RFH_RXF_DMA_MIN_RB_4_8 (3 << RFH_RXF_DMA_MIN_RB_SIZE_POS)
#define RFH_RXF_DMA_DROP_TOO_LARGE_MASK (0x04000000) /* bit 26 */
#define RFH_RXF_DMA_SINGLE_FRAME_MASK (0x20000000) /* bit 29 */
#define RFH_DMA_EN_MASK (0xC0000000) /* bits 30-31*/
#define RFH_DMA_EN_ENABLE_VAL BIT(31)
#define RFH_RXF_RXQ_ACTIVE 0xA0980C
#define RFH_GEN_CFG 0xA09800
#define RFH_GEN_CFG_SERVICE_DMA_SNOOP BIT(0)
#define RFH_GEN_CFG_RFH_DMA_SNOOP BIT(1)
#define RFH_GEN_CFG_RB_CHUNK_SIZE BIT(4)
#define RFH_GEN_CFG_RB_CHUNK_SIZE_128 1
#define RFH_GEN_CFG_RB_CHUNK_SIZE_64 0
/* the driver assumes everywhere that the default RXQ is 0 */
#define RFH_GEN_CFG_DEFAULT_RXQ_NUM 0xF00
#define RFH_GEN_CFG_VAL(_n, _v) FIELD_PREP(RFH_GEN_CFG_ ## _n, _v)
/* end of 9000 rx series registers */
/* TFDB Area - TFDs buffer table */
#define FH_MEM_TFDIB_DRAM_ADDR_LSB_MSK (0xFFFFFFFF)
#define FH_TFDIB_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x900)
#define FH_TFDIB_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0x958)
#define FH_TFDIB_CTRL0_REG(_chnl) (FH_TFDIB_LOWER_BOUND + 0x8 * (_chnl))
#define FH_TFDIB_CTRL1_REG(_chnl) (FH_TFDIB_LOWER_BOUND + 0x8 * (_chnl) + 0x4)
/**
* Transmit DMA Channel Control/Status Registers (TCSR)
*
* Device has one configuration register for each of 8 Tx DMA/FIFO channels
* supported in hardware (don't confuse these with the 16 Tx queues in DRAM,
* which feed the DMA/FIFO channels); config regs are separated by 0x20 bytes.
*
* To use a Tx DMA channel, driver must initialize its
* FH_TCSR_CHNL_TX_CONFIG_REG(chnl) with:
*
* FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE |
* FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL
*
* All other bits should be 0.
*
* Bit fields:
* 31-30: Tx DMA channel enable: '00' off/pause, '01' pause at end of frame,
* '10' operate normally
* 29- 4: Reserved, set to "0"
* 3: Enable internal DMA requests (1, normal operation), disable (0)
* 2- 0: Reserved, set to "0"
*/
#define FH_TCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xD00)
#define FH_TCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xE60)
/* Find Control/Status reg for given Tx DMA/FIFO channel */
#define FH_TCSR_CHNL_NUM (8)
/* TCSR: tx_config register values */
#define FH_TCSR_CHNL_TX_CONFIG_REG(_chnl) \
(FH_TCSR_LOWER_BOUND + 0x20 * (_chnl))
#define FH_TCSR_CHNL_TX_CREDIT_REG(_chnl) \
(FH_TCSR_LOWER_BOUND + 0x20 * (_chnl) + 0x4)
#define FH_TCSR_CHNL_TX_BUF_STS_REG(_chnl) \
(FH_TCSR_LOWER_BOUND + 0x20 * (_chnl) + 0x8)
#define FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF (0x00000000)
#define FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_DRV (0x00000001)
#define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE (0x00000000)
#define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE (0x00000008)
#define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_NOINT (0x00000000)
#define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_ENDTFD (0x00100000)
#define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD (0x00200000)
#define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT (0x00000000)
#define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_ENDTFD (0x00400000)
#define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_IFTFD (0x00800000)
#define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000)
#define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF (0x40000000)
#define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000)
#define FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_EMPTY (0x00000000)
#define FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_WAIT (0x00002000)
#define FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_VALID (0x00000003)
#define FH_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_NUM (20)
#define FH_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_IDX (12)
/**
* Tx Shared Status Registers (TSSR)
*
* After stopping Tx DMA channel (writing 0 to
* FH_TCSR_CHNL_TX_CONFIG_REG(chnl)), driver must poll
* FH_TSSR_TX_STATUS_REG until selected Tx channel is idle
* (channel's buffers empty | no pending requests).
*
* Bit fields:
* 31-24: 1 = Channel buffers empty (channel 7:0)
* 23-16: 1 = No pending requests (channel 7:0)
*/
#define FH_TSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xEA0)
#define FH_TSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xEC0)
#define FH_TSSR_TX_STATUS_REG (FH_TSSR_LOWER_BOUND + 0x010)
/**
* Bit fields for TSSR(Tx Shared Status & Control) error status register:
* 31: Indicates an address error when accessed to internal memory
* uCode/driver must write "1" in order to clear this flag
* 30: Indicates that Host did not send the expected number of dwords to FH
* uCode/driver must write "1" in order to clear this flag
* 16-9:Each status bit is for one channel. Indicates that an (Error) ActDMA
* command was received from the scheduler while the TRB was already full
* with previous command
* uCode/driver must write "1" in order to clear this flag
* 7-0: Each status bit indicates a channel's TxCredit error. When an error
* bit is set, it indicates that the FH has received a full indication
* from the RTC TxFIFO and the current value of the TxCredit counter was
* not equal to zero. This mean that the credit mechanism was not
* synchronized to the TxFIFO status
* uCode/driver must write "1" in order to clear this flag
*/
#define FH_TSSR_TX_ERROR_REG (FH_TSSR_LOWER_BOUND + 0x018)
#define FH_TSSR_TX_MSG_CONFIG_REG (FH_TSSR_LOWER_BOUND + 0x008)
#define FH_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(_chnl) ((1 << (_chnl)) << 16)
/* Tx service channels */
#define FH_SRVC_CHNL (9)
#define FH_SRVC_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x9C8)
#define FH_SRVC_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0x9D0)
#define FH_SRVC_CHNL_SRAM_ADDR_REG(_chnl) \
(FH_SRVC_LOWER_BOUND + ((_chnl) - 9) * 0x4)
#define FH_TX_CHICKEN_BITS_REG (FH_MEM_LOWER_BOUND + 0xE98)
#define FH_TX_TRB_REG(_chan) (FH_MEM_LOWER_BOUND + 0x958 + (_chan) * 4)
/* Instruct FH to increment the retry count of a packet when
* it is brought from the memory to TX-FIFO
*/
#define FH_TX_CHICKEN_BITS_SCD_AUTO_RETRY_EN (0x00000002)
#define MQ_RX_TABLE_SIZE 512
#define MQ_RX_TABLE_MASK (MQ_RX_TABLE_SIZE - 1)
#define MQ_RX_NUM_RBDS (MQ_RX_TABLE_SIZE - 1)
#define RX_POOL_SIZE (MQ_RX_NUM_RBDS + \
IWL_MAX_RX_HW_QUEUES * \
(RX_CLAIM_REQ_ALLOC - RX_POST_REQ_ALLOC))
/* cb size is the exponent */
#define RX_QUEUE_CB_SIZE(x) ilog2(x)
#define RX_QUEUE_SIZE 256
#define RX_QUEUE_MASK 255
#define RX_QUEUE_SIZE_LOG 8
/**
* struct iwl_rb_status - reserve buffer status
* host memory mapped FH registers
* @closed_rb_num [0:11] - Indicates the index of the RB which was closed
* @closed_fr_num [0:11] - Indicates the index of the RX Frame which was closed
* @finished_rb_num [0:11] - Indicates the index of the current RB
* in which the last frame was written to
* @finished_fr_num [0:11] - Indicates the index of the RX Frame
* which was transferred
*/
struct iwl_rb_status {
__le16 closed_rb_num;
__le16 closed_fr_num;
__le16 finished_rb_num;
__le16 finished_fr_nam;
__le32 __unused;
} __packed;
#define TFD_QUEUE_SIZE_MAX (256)
#define TFD_QUEUE_SIZE_MAX_GEN3 (65536)
/* cb size is the exponent - 3 */
#define TFD_QUEUE_CB_SIZE(x) (ilog2(x) - 3)
#define TFD_QUEUE_SIZE_BC_DUP (64)
#define TFD_QUEUE_BC_SIZE (TFD_QUEUE_SIZE_MAX + TFD_QUEUE_SIZE_BC_DUP)
#define TFD_QUEUE_BC_SIZE_GEN3 (TFD_QUEUE_SIZE_MAX_GEN3 + \
TFD_QUEUE_SIZE_BC_DUP)
#define IWL_TX_DMA_MASK DMA_BIT_MASK(36)
#define IWL_NUM_OF_TBS 20
#define IWL_TFH_NUM_TBS 25
static inline u8 iwl_get_dma_hi_addr(dma_addr_t addr)
{
return (sizeof(addr) > sizeof(u32) ? upper_32_bits(addr) : 0) & 0xF;
}
/**
* enum iwl_tfd_tb_hi_n_len - TB hi_n_len bits
* @TB_HI_N_LEN_ADDR_HI_MSK: high 4 bits (to make it 36) of DMA address
* @TB_HI_N_LEN_LEN_MSK: length of the TB
*/
enum iwl_tfd_tb_hi_n_len {
TB_HI_N_LEN_ADDR_HI_MSK = 0xf,
TB_HI_N_LEN_LEN_MSK = 0xfff0,
};
/**
* struct iwl_tfd_tb transmit buffer descriptor within transmit frame descriptor
*
* This structure contains dma address and length of transmission address
*
* @lo: low [31:0] portion of the dma address of TX buffer
* every even is unaligned on 16 bit boundary
* @hi_n_len: &enum iwl_tfd_tb_hi_n_len
*/
struct iwl_tfd_tb {
__le32 lo;
__le16 hi_n_len;
} __packed;
/**
* struct iwl_tfh_tb transmit buffer descriptor within transmit frame descriptor
*
* This structure contains dma address and length of transmission address
*
* @tb_len length of the tx buffer
* @addr 64 bits dma address
*/
struct iwl_tfh_tb {
__le16 tb_len;
__le64 addr;
} __packed;
/**
* Each Tx queue uses a circular buffer of 256 TFDs stored in host DRAM.
* Both driver and device share these circular buffers, each of which must be
* contiguous 256 TFDs.
* For pre 22000 HW it is 256 x 128 bytes-per-TFD = 32 KBytes
* For 22000 HW and on it is 256 x 256 bytes-per-TFD = 65 KBytes
*
* Driver must indicate the physical address of the base of each
* circular buffer via the FH_MEM_CBBC_QUEUE registers.
*
* Each TFD contains pointer/size information for up to 20 / 25 data buffers
* in host DRAM. These buffers collectively contain the (one) frame described
* by the TFD. Each buffer must be a single contiguous block of memory within
* itself, but buffers may be scattered in host DRAM. Each buffer has max size
* of (4K - 4). The concatenates all of a TFD's buffers into a single
* Tx frame, up to 8 KBytes in size.
*
* A maximum of 255 (not 256!) TFDs may be on a queue waiting for Tx.
*/
/**
* struct iwl_tfd - Transmit Frame Descriptor (TFD)
* @ __reserved1[3] reserved
* @ num_tbs 0-4 number of active tbs
* 5 reserved
* 6-7 padding (not used)
* @ tbs[20] transmit frame buffer descriptors
* @ __pad padding
*/
struct iwl_tfd {
u8 __reserved1[3];
u8 num_tbs;
struct iwl_tfd_tb tbs[IWL_NUM_OF_TBS];
__le32 __pad;
} __packed;
/**
* struct iwl_tfh_tfd - Transmit Frame Descriptor (TFD)
* @ num_tbs 0-4 number of active tbs
* 5 -15 reserved
* @ tbs[25] transmit frame buffer descriptors
* @ __pad padding
*/
struct iwl_tfh_tfd {
__le16 num_tbs;
struct iwl_tfh_tb tbs[IWL_TFH_NUM_TBS];
__le32 __pad;
} __packed;
/* Keep Warm Size */
#define IWL_KW_SIZE 0x1000 /* 4k */
/* Fixed (non-configurable) rx data from phy */
/**
* struct iwlagn_schedq_bc_tbl scheduler byte count table
* base physical address provided by SCD_DRAM_BASE_ADDR
* For devices up to 22000:
* @tfd_offset 0-12 - tx command byte count
* 12-16 - station index
* For 22000:
* @tfd_offset 0-12 - tx command byte count
* 12-13 - number of 64 byte chunks
* 14-16 - reserved
*/
struct iwlagn_scd_bc_tbl {
__le16 tfd_offset[TFD_QUEUE_BC_SIZE];
} __packed;
/**
* struct iwl_gen3_bc_tbl scheduler byte count table gen3
* For 22560 and on:
* @tfd_offset: 0-12 - tx command byte count
* 12-13 - number of 64 byte chunks
* 14-16 - reserved
*/
struct iwl_gen3_bc_tbl {
__le16 tfd_offset[TFD_QUEUE_BC_SIZE_GEN3];
} __packed;
#endif /* !__iwl_fh_h__ */