| /* | |
| * | |
| * 2.6 port, Embedded Alley Solutions, Inc | |
| * | |
| * Based on Per Hallsmark, per.hallsmark@mvista.com | |
| * | |
| * This program is free software; you can distribute it and/or modify it | |
| * under the terms of the GNU General Public License (Version 2) as | |
| * published by the Free Software Foundation. | |
| * | |
| * This program is distributed in the hope it will be useful, but WITHOUT | |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or | |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License | |
| * for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License along | |
| * with this program; if not, write to the Free Software Foundation, Inc., | |
| * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA. | |
| */ | |
| #include <linux/init.h> | |
| #include <linux/sched.h> | |
| #include <linux/ioport.h> | |
| #include <linux/irq.h> | |
| #include <linux/mm.h> | |
| #include <linux/delay.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/serial_pnx8xxx.h> | |
| #include <linux/pm.h> | |
| #include <asm/cpu.h> | |
| #include <asm/bootinfo.h> | |
| #include <asm/irq.h> | |
| #include <asm/mipsregs.h> | |
| #include <asm/reboot.h> | |
| #include <asm/pgtable.h> | |
| #include <asm/time.h> | |
| #include <glb.h> | |
| #include <int.h> | |
| #include <pci.h> | |
| #include <uart.h> | |
| #include <nand.h> | |
| extern void __init board_setup(void); | |
| extern void pnx8550_machine_restart(char *); | |
| extern void pnx8550_machine_halt(void); | |
| extern struct resource ioport_resource; | |
| extern struct resource iomem_resource; | |
| extern char *prom_getcmdline(void); | |
| struct resource standard_io_resources[] = { | |
| { | |
| .start = 0x00, | |
| .end = 0x1f, | |
| .name = "dma1", | |
| .flags = IORESOURCE_BUSY | |
| }, { | |
| .start = 0x40, | |
| .end = 0x5f, | |
| .name = "timer", | |
| .flags = IORESOURCE_BUSY | |
| }, { | |
| .start = 0x80, | |
| .end = 0x8f, | |
| .name = "dma page reg", | |
| .flags = IORESOURCE_BUSY | |
| }, { | |
| .start = 0xc0, | |
| .end = 0xdf, | |
| .name = "dma2", | |
| .flags = IORESOURCE_BUSY | |
| }, | |
| }; | |
| #define STANDARD_IO_RESOURCES ARRAY_SIZE(standard_io_resources) | |
| extern struct resource pci_io_resource; | |
| extern struct resource pci_mem_resource; | |
| /* Return the total size of DRAM-memory, (RANK0 + RANK1) */ | |
| unsigned long get_system_mem_size(void) | |
| { | |
| /* Read IP2031_RANK0_ADDR_LO */ | |
| unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010); | |
| /* Read IP2031_RANK1_ADDR_HI */ | |
| unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018); | |
| return dram_r1_hi - dram_r0_lo + 1; | |
| } | |
| int pnx8550_console_port = -1; | |
| void __init plat_mem_setup(void) | |
| { | |
| int i; | |
| char* argptr; | |
| board_setup(); /* board specific setup */ | |
| _machine_restart = pnx8550_machine_restart; | |
| _machine_halt = pnx8550_machine_halt; | |
| pm_power_off = pnx8550_machine_halt; | |
| /* Clear the Global 2 Register, PCI Inta Output Enable Registers | |
| Bit 1:Enable DAC Powerdown | |
| -> 0:DACs are enabled and are working normally | |
| 1:DACs are powerdown | |
| Bit 0:Enable of PCI inta output | |
| -> 0 = Disable PCI inta output | |
| 1 = Enable PCI inta output | |
| */ | |
| PNX8550_GLB2_ENAB_INTA_O = 0; | |
| /* IO/MEM resources. */ | |
| set_io_port_base(PNX8550_PORT_BASE); | |
| ioport_resource.start = 0; | |
| ioport_resource.end = ~0; | |
| iomem_resource.start = 0; | |
| iomem_resource.end = ~0; | |
| /* Request I/O space for devices on this board */ | |
| for (i = 0; i < STANDARD_IO_RESOURCES; i++) | |
| request_resource(&ioport_resource, standard_io_resources + i); | |
| /* Place the Mode Control bit for GPIO pin 16 in primary function */ | |
| /* Pin 16 is used by UART1, UA1_TX */ | |
| outl((PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_16_BIT) | | |
| (PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_17_BIT), | |
| PNX8550_GPIO_MC1); | |
| argptr = prom_getcmdline(); | |
| if ((argptr = strstr(argptr, "console=ttyS")) != NULL) { | |
| argptr += strlen("console=ttyS"); | |
| pnx8550_console_port = *argptr == '0' ? 0 : 1; | |
| /* We must initialize the UART (console) before early printk */ | |
| /* Set LCR to 8-bit and BAUD to 38400 (no 5) */ | |
| ip3106_lcr(UART_BASE, pnx8550_console_port) = | |
| PNX8XXX_UART_LCR_8BIT; | |
| ip3106_baud(UART_BASE, pnx8550_console_port) = 5; | |
| } | |
| } |