| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * arch/arm/mach-netx/nxdb500.c |
| * |
| * Copyright (c) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix |
| */ |
| |
| #include <linux/dma-mapping.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/mtd/plat-ram.h> |
| #include <linux/platform_device.h> |
| #include <linux/amba/bus.h> |
| #include <linux/amba/clcd.h> |
| |
| #include <mach/hardware.h> |
| #include <asm/mach-types.h> |
| #include <asm/mach/arch.h> |
| #include <mach/netx-regs.h> |
| #include <linux/platform_data/eth-netx.h> |
| |
| #include "generic.h" |
| #include "fb.h" |
| |
| static struct clcd_panel qvga = { |
| .mode = { |
| .name = "QVGA", |
| .refresh = 60, |
| .xres = 240, |
| .yres = 320, |
| .pixclock = 187617, |
| .left_margin = 6, |
| .right_margin = 26, |
| .upper_margin = 0, |
| .lower_margin = 6, |
| .hsync_len = 6, |
| .vsync_len = 1, |
| .sync = 0, |
| .vmode = FB_VMODE_NONINTERLACED, |
| }, |
| .width = -1, |
| .height = -1, |
| .tim2 = 16, |
| .cntl = CNTL_LCDTFT | CNTL_BGR, |
| .bpp = 16, |
| .grayscale = 0, |
| }; |
| |
| static inline int nxdb500_check(struct clcd_fb *fb, struct fb_var_screeninfo *var) |
| { |
| var->green.length = 5; |
| var->green.msb_right = 0; |
| |
| return clcdfb_check(fb, var); |
| } |
| |
| static int nxdb500_clcd_setup(struct clcd_fb *fb) |
| { |
| unsigned int val; |
| |
| fb->fb.var.green.length = 5; |
| fb->fb.var.green.msb_right = 0; |
| |
| /* enable asic control */ |
| val = readl(NETX_SYSTEM_IOC_ACCESS_KEY); |
| writel(val, NETX_SYSTEM_IOC_ACCESS_KEY); |
| |
| writel(3, NETX_SYSTEM_IOC_CR); |
| |
| val = readl(NETX_PIO_OUTPIO); |
| writel(val | 1, NETX_PIO_OUTPIO); |
| |
| val = readl(NETX_PIO_OEPIO); |
| writel(val | 1, NETX_PIO_OEPIO); |
| return netx_clcd_setup(fb); |
| } |
| |
| static struct clcd_board clcd_data = { |
| .name = "netX", |
| .check = nxdb500_check, |
| .decode = clcdfb_decode, |
| .enable = netx_clcd_enable, |
| .setup = nxdb500_clcd_setup, |
| .mmap = netx_clcd_mmap, |
| .remove = netx_clcd_remove, |
| }; |
| |
| static struct netxeth_platform_data eth0_platform_data = { |
| .xcno = 0, |
| }; |
| |
| static struct platform_device netx_eth0_device = { |
| .name = "netx-eth", |
| .id = 0, |
| .num_resources = 0, |
| .resource = NULL, |
| .dev = { |
| .platform_data = ð0_platform_data, |
| } |
| }; |
| |
| static struct netxeth_platform_data eth1_platform_data = { |
| .xcno = 1, |
| }; |
| |
| static struct platform_device netx_eth1_device = { |
| .name = "netx-eth", |
| .id = 1, |
| .num_resources = 0, |
| .resource = NULL, |
| .dev = { |
| .platform_data = ð1_platform_data, |
| } |
| }; |
| |
| static struct resource netx_uart0_resources[] = { |
| [0] = { |
| .start = 0x00100A00, |
| .end = 0x00100A3F, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = (NETX_IRQ_UART0), |
| .end = (NETX_IRQ_UART0), |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device netx_uart0_device = { |
| .name = "netx-uart", |
| .id = 0, |
| .num_resources = ARRAY_SIZE(netx_uart0_resources), |
| .resource = netx_uart0_resources, |
| }; |
| |
| static struct resource netx_uart1_resources[] = { |
| [0] = { |
| .start = 0x00100A40, |
| .end = 0x00100A7F, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = (NETX_IRQ_UART1), |
| .end = (NETX_IRQ_UART1), |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device netx_uart1_device = { |
| .name = "netx-uart", |
| .id = 1, |
| .num_resources = ARRAY_SIZE(netx_uart1_resources), |
| .resource = netx_uart1_resources, |
| }; |
| |
| static struct resource netx_uart2_resources[] = { |
| [0] = { |
| .start = 0x00100A80, |
| .end = 0x00100ABF, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = (NETX_IRQ_UART2), |
| .end = (NETX_IRQ_UART2), |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device netx_uart2_device = { |
| .name = "netx-uart", |
| .id = 2, |
| .num_resources = ARRAY_SIZE(netx_uart2_resources), |
| .resource = netx_uart2_resources, |
| }; |
| |
| static struct platform_device *devices[] __initdata = { |
| &netx_eth0_device, |
| &netx_eth1_device, |
| &netx_uart0_device, |
| &netx_uart1_device, |
| &netx_uart2_device, |
| }; |
| |
| static void __init nxdb500_init(void) |
| { |
| netx_fb_init(&clcd_data, &qvga); |
| platform_add_devices(devices, ARRAY_SIZE(devices)); |
| } |
| |
| MACHINE_START(NXDB500, "Hilscher nxdb500") |
| .atag_offset = 0x100, |
| .map_io = netx_map_io, |
| .init_irq = netx_init_irq, |
| .init_time = netx_timer_init, |
| .init_machine = nxdb500_init, |
| .restart = netx_restart, |
| MACHINE_END |