|  | // SPDX-License-Identifier: GPL-2.0 | 
|  | /* | 
|  | * Copyright (C) 2018 Samsung Electronics Co., Ltd | 
|  | * | 
|  | * Authors: | 
|  | *	Andrzej Hajda <a.hajda@samsung.com> | 
|  | *	Maciej Purski <m.purski@samsung.com> | 
|  | */ | 
|  |  | 
|  | #include <drm/drm_atomic_helper.h> | 
|  | #include <drm/drm_crtc.h> | 
|  | #include <drm/drm_crtc_helper.h> | 
|  | #include <drm/drm_fb_helper.h> | 
|  | #include <drm/drm_mipi_dsi.h> | 
|  | #include <drm/drm_of.h> | 
|  | #include <drm/drm_panel.h> | 
|  | #include <drm/drmP.h> | 
|  | #include <linux/gpio/consumer.h> | 
|  | #include <linux/of_graph.h> | 
|  | #include <linux/regulator/consumer.h> | 
|  | #include <video/mipi_display.h> | 
|  |  | 
|  | #define FLD_MASK(start, end)    (((1 << ((start) - (end) + 1)) - 1) << (end)) | 
|  | #define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end)) | 
|  |  | 
|  | /* PPI layer registers */ | 
|  | #define PPI_STARTPPI		0x0104 /* START control bit */ | 
|  | #define PPI_LPTXTIMECNT		0x0114 /* LPTX timing signal */ | 
|  | #define PPI_LANEENABLE		0x0134 /* Enables each lane */ | 
|  | #define PPI_TX_RX_TA		0x013C /* BTA timing parameters */ | 
|  | #define PPI_D0S_CLRSIPOCOUNT	0x0164 /* Assertion timer for Lane 0 */ | 
|  | #define PPI_D1S_CLRSIPOCOUNT	0x0168 /* Assertion timer for Lane 1 */ | 
|  | #define PPI_D2S_CLRSIPOCOUNT	0x016C /* Assertion timer for Lane 2 */ | 
|  | #define PPI_D3S_CLRSIPOCOUNT	0x0170 /* Assertion timer for Lane 3 */ | 
|  | #define PPI_START_FUNCTION	1 | 
|  |  | 
|  | /* DSI layer registers */ | 
|  | #define DSI_STARTDSI		0x0204 /* START control bit of DSI-TX */ | 
|  | #define DSI_LANEENABLE		0x0210 /* Enables each lane */ | 
|  | #define DSI_RX_START		1 | 
|  |  | 
|  | /* Video path registers */ | 
|  | #define VP_CTRL			0x0450 /* Video Path Control */ | 
|  | #define VP_CTRL_MSF(v)		FLD_VAL(v, 0, 0) /* Magic square in RGB666 */ | 
|  | #define VP_CTRL_VTGEN(v)	FLD_VAL(v, 4, 4) /* Use chip clock for timing */ | 
|  | #define VP_CTRL_EVTMODE(v)	FLD_VAL(v, 5, 5) /* Event mode */ | 
|  | #define VP_CTRL_RGB888(v)	FLD_VAL(v, 8, 8) /* RGB888 mode */ | 
|  | #define VP_CTRL_VSDELAY(v)	FLD_VAL(v, 31, 20) /* VSYNC delay */ | 
|  | #define VP_CTRL_HSPOL		BIT(17) /* Polarity of HSYNC signal */ | 
|  | #define VP_CTRL_DEPOL		BIT(18) /* Polarity of DE signal */ | 
|  | #define VP_CTRL_VSPOL		BIT(19) /* Polarity of VSYNC signal */ | 
|  | #define VP_HTIM1		0x0454 /* Horizontal Timing Control 1 */ | 
|  | #define VP_HTIM1_HBP(v)		FLD_VAL(v, 24, 16) | 
|  | #define VP_HTIM1_HSYNC(v)	FLD_VAL(v, 8, 0) | 
|  | #define VP_HTIM2		0x0458 /* Horizontal Timing Control 2 */ | 
|  | #define VP_HTIM2_HFP(v)		FLD_VAL(v, 24, 16) | 
|  | #define VP_HTIM2_HACT(v)	FLD_VAL(v, 10, 0) | 
|  | #define VP_VTIM1		0x045C /* Vertical Timing Control 1 */ | 
|  | #define VP_VTIM1_VBP(v)		FLD_VAL(v, 23, 16) | 
|  | #define VP_VTIM1_VSYNC(v)	FLD_VAL(v, 7, 0) | 
|  | #define VP_VTIM2		0x0460 /* Vertical Timing Control 2 */ | 
|  | #define VP_VTIM2_VFP(v)		FLD_VAL(v, 23, 16) | 
|  | #define VP_VTIM2_VACT(v)	FLD_VAL(v, 10, 0) | 
|  | #define VP_VFUEN		0x0464 /* Video Frame Timing Update Enable */ | 
|  |  | 
|  | /* LVDS registers */ | 
|  | #define LV_MX0003		0x0480 /* Mux input bit 0 to 3 */ | 
|  | #define LV_MX0407		0x0484 /* Mux input bit 4 to 7 */ | 
|  | #define LV_MX0811		0x0488 /* Mux input bit 8 to 11 */ | 
|  | #define LV_MX1215		0x048C /* Mux input bit 12 to 15 */ | 
|  | #define LV_MX1619		0x0490 /* Mux input bit 16 to 19 */ | 
|  | #define LV_MX2023		0x0494 /* Mux input bit 20 to 23 */ | 
|  | #define LV_MX2427		0x0498 /* Mux input bit 24 to 27 */ | 
|  | #define LV_MX(b0, b1, b2, b3)	(FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \ | 
|  | FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24)) | 
|  |  | 
|  | /* Input bit numbers used in mux registers */ | 
|  | enum { | 
|  | LVI_R0, | 
|  | LVI_R1, | 
|  | LVI_R2, | 
|  | LVI_R3, | 
|  | LVI_R4, | 
|  | LVI_R5, | 
|  | LVI_R6, | 
|  | LVI_R7, | 
|  | LVI_G0, | 
|  | LVI_G1, | 
|  | LVI_G2, | 
|  | LVI_G3, | 
|  | LVI_G4, | 
|  | LVI_G5, | 
|  | LVI_G6, | 
|  | LVI_G7, | 
|  | LVI_B0, | 
|  | LVI_B1, | 
|  | LVI_B2, | 
|  | LVI_B3, | 
|  | LVI_B4, | 
|  | LVI_B5, | 
|  | LVI_B6, | 
|  | LVI_B7, | 
|  | LVI_HS, | 
|  | LVI_VS, | 
|  | LVI_DE, | 
|  | LVI_L0 | 
|  | }; | 
|  |  | 
|  | #define LV_CFG			0x049C /* LVDS Configuration */ | 
|  | #define LV_PHY0			0x04A0 /* LVDS PHY 0 */ | 
|  | #define LV_PHY0_RST(v)		FLD_VAL(v, 22, 22) /* PHY reset */ | 
|  | #define LV_PHY0_IS(v)		FLD_VAL(v, 15, 14) | 
|  | #define LV_PHY0_ND(v)		FLD_VAL(v, 4, 0) /* Frequency range select */ | 
|  | #define LV_PHY0_PRBS_ON(v)	FLD_VAL(v, 20, 16) /* Clock/Data Flag pins */ | 
|  |  | 
|  | /* System registers */ | 
|  | #define SYS_RST			0x0504 /* System Reset */ | 
|  | #define SYS_ID			0x0580 /* System ID */ | 
|  |  | 
|  | #define SYS_RST_I2CS		BIT(0) /* Reset I2C-Slave controller */ | 
|  | #define SYS_RST_I2CM		BIT(1) /* Reset I2C-Master controller */ | 
|  | #define SYS_RST_LCD		BIT(2) /* Reset LCD controller */ | 
|  | #define SYS_RST_BM		BIT(3) /* Reset Bus Management controller */ | 
|  | #define SYS_RST_DSIRX		BIT(4) /* Reset DSI-RX and App controller */ | 
|  | #define SYS_RST_REG		BIT(5) /* Reset Register module */ | 
|  |  | 
|  | #define LPX_PERIOD		2 | 
|  | #define TTA_SURE		3 | 
|  | #define TTA_GET			0x20000 | 
|  |  | 
|  | /* Lane enable PPI and DSI register bits */ | 
|  | #define LANEENABLE_CLEN		BIT(0) | 
|  | #define LANEENABLE_L0EN		BIT(1) | 
|  | #define LANEENABLE_L1EN		BIT(2) | 
|  | #define LANEENABLE_L2EN		BIT(3) | 
|  | #define LANEENABLE_L3EN		BIT(4) | 
|  |  | 
|  | /* LVCFG fields */ | 
|  | #define LV_CFG_LVEN		BIT(0) | 
|  | #define LV_CFG_LVDLINK		BIT(1) | 
|  | #define LV_CFG_CLKPOL1		BIT(2) | 
|  | #define LV_CFG_CLKPOL2		BIT(3) | 
|  |  | 
|  | static const char * const tc358764_supplies[] = { | 
|  | "vddc", "vddio", "vddlvds" | 
|  | }; | 
|  |  | 
|  | struct tc358764 { | 
|  | struct device *dev; | 
|  | struct drm_bridge bridge; | 
|  | struct drm_connector connector; | 
|  | struct regulator_bulk_data supplies[ARRAY_SIZE(tc358764_supplies)]; | 
|  | struct gpio_desc *gpio_reset; | 
|  | struct drm_panel *panel; | 
|  | int error; | 
|  | }; | 
|  |  | 
|  | static int tc358764_clear_error(struct tc358764 *ctx) | 
|  | { | 
|  | int ret = ctx->error; | 
|  |  | 
|  | ctx->error = 0; | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void tc358764_read(struct tc358764 *ctx, u16 addr, u32 *val) | 
|  | { | 
|  | struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); | 
|  | ssize_t ret; | 
|  |  | 
|  | if (ctx->error) | 
|  | return; | 
|  |  | 
|  | cpu_to_le16s(&addr); | 
|  | ret = mipi_dsi_generic_read(dsi, &addr, sizeof(addr), val, sizeof(*val)); | 
|  | if (ret >= 0) | 
|  | le32_to_cpus(val); | 
|  |  | 
|  | dev_dbg(ctx->dev, "read: %d, addr: %d\n", addr, *val); | 
|  | } | 
|  |  | 
|  | static void tc358764_write(struct tc358764 *ctx, u16 addr, u32 val) | 
|  | { | 
|  | struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); | 
|  | ssize_t ret; | 
|  | u8 data[6]; | 
|  |  | 
|  | if (ctx->error) | 
|  | return; | 
|  |  | 
|  | data[0] = addr; | 
|  | data[1] = addr >> 8; | 
|  | data[2] = val; | 
|  | data[3] = val >> 8; | 
|  | data[4] = val >> 16; | 
|  | data[5] = val >> 24; | 
|  |  | 
|  | ret = mipi_dsi_generic_write(dsi, data, sizeof(data)); | 
|  | if (ret < 0) | 
|  | ctx->error = ret; | 
|  | } | 
|  |  | 
|  | static inline struct tc358764 *bridge_to_tc358764(struct drm_bridge *bridge) | 
|  | { | 
|  | return container_of(bridge, struct tc358764, bridge); | 
|  | } | 
|  |  | 
|  | static inline | 
|  | struct tc358764 *connector_to_tc358764(struct drm_connector *connector) | 
|  | { | 
|  | return container_of(connector, struct tc358764, connector); | 
|  | } | 
|  |  | 
|  | static int tc358764_init(struct tc358764 *ctx) | 
|  | { | 
|  | u32 v = 0; | 
|  |  | 
|  | tc358764_read(ctx, SYS_ID, &v); | 
|  | if (ctx->error) | 
|  | return tc358764_clear_error(ctx); | 
|  | dev_info(ctx->dev, "ID: %#x\n", v); | 
|  |  | 
|  | /* configure PPI counters */ | 
|  | tc358764_write(ctx, PPI_TX_RX_TA, TTA_GET | TTA_SURE); | 
|  | tc358764_write(ctx, PPI_LPTXTIMECNT, LPX_PERIOD); | 
|  | tc358764_write(ctx, PPI_D0S_CLRSIPOCOUNT, 5); | 
|  | tc358764_write(ctx, PPI_D1S_CLRSIPOCOUNT, 5); | 
|  | tc358764_write(ctx, PPI_D2S_CLRSIPOCOUNT, 5); | 
|  | tc358764_write(ctx, PPI_D3S_CLRSIPOCOUNT, 5); | 
|  |  | 
|  | /* enable four data lanes and clock lane */ | 
|  | tc358764_write(ctx, PPI_LANEENABLE, LANEENABLE_L3EN | LANEENABLE_L2EN | | 
|  | LANEENABLE_L1EN | LANEENABLE_L0EN | LANEENABLE_CLEN); | 
|  | tc358764_write(ctx, DSI_LANEENABLE, LANEENABLE_L3EN | LANEENABLE_L2EN | | 
|  | LANEENABLE_L1EN | LANEENABLE_L0EN | LANEENABLE_CLEN); | 
|  |  | 
|  | /* start */ | 
|  | tc358764_write(ctx, PPI_STARTPPI, PPI_START_FUNCTION); | 
|  | tc358764_write(ctx, DSI_STARTDSI, DSI_RX_START); | 
|  |  | 
|  | /* configure video path */ | 
|  | tc358764_write(ctx, VP_CTRL, VP_CTRL_VSDELAY(15) | VP_CTRL_RGB888(1) | | 
|  | VP_CTRL_EVTMODE(1) | VP_CTRL_HSPOL | VP_CTRL_VSPOL); | 
|  |  | 
|  | /* reset PHY */ | 
|  | tc358764_write(ctx, LV_PHY0, LV_PHY0_RST(1) | | 
|  | LV_PHY0_PRBS_ON(4) | LV_PHY0_IS(2) | LV_PHY0_ND(6)); | 
|  | tc358764_write(ctx, LV_PHY0, LV_PHY0_PRBS_ON(4) | LV_PHY0_IS(2) | | 
|  | LV_PHY0_ND(6)); | 
|  |  | 
|  | /* reset bridge */ | 
|  | tc358764_write(ctx, SYS_RST, SYS_RST_LCD); | 
|  |  | 
|  | /* set bit order */ | 
|  | tc358764_write(ctx, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3)); | 
|  | tc358764_write(ctx, LV_MX0407, LV_MX(LVI_R4, LVI_R7, LVI_R5, LVI_G0)); | 
|  | tc358764_write(ctx, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_G6, LVI_G7)); | 
|  | tc358764_write(ctx, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0)); | 
|  | tc358764_write(ctx, LV_MX1619, LV_MX(LVI_B6, LVI_B7, LVI_B1, LVI_B2)); | 
|  | tc358764_write(ctx, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0)); | 
|  | tc358764_write(ctx, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R6)); | 
|  | tc358764_write(ctx, LV_CFG, LV_CFG_CLKPOL2 | LV_CFG_CLKPOL1 | | 
|  | LV_CFG_LVEN); | 
|  |  | 
|  | return tc358764_clear_error(ctx); | 
|  | } | 
|  |  | 
|  | static void tc358764_reset(struct tc358764 *ctx) | 
|  | { | 
|  | gpiod_set_value(ctx->gpio_reset, 1); | 
|  | usleep_range(1000, 2000); | 
|  | gpiod_set_value(ctx->gpio_reset, 0); | 
|  | usleep_range(1000, 2000); | 
|  | } | 
|  |  | 
|  | static int tc358764_get_modes(struct drm_connector *connector) | 
|  | { | 
|  | struct tc358764 *ctx = connector_to_tc358764(connector); | 
|  |  | 
|  | return drm_panel_get_modes(ctx->panel); | 
|  | } | 
|  |  | 
|  | static const | 
|  | struct drm_connector_helper_funcs tc358764_connector_helper_funcs = { | 
|  | .get_modes = tc358764_get_modes, | 
|  | }; | 
|  |  | 
|  | static const struct drm_connector_funcs tc358764_connector_funcs = { | 
|  | .fill_modes = drm_helper_probe_single_connector_modes, | 
|  | .destroy = drm_connector_cleanup, | 
|  | .reset = drm_atomic_helper_connector_reset, | 
|  | .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, | 
|  | .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, | 
|  | }; | 
|  |  | 
|  | static void tc358764_disable(struct drm_bridge *bridge) | 
|  | { | 
|  | struct tc358764 *ctx = bridge_to_tc358764(bridge); | 
|  | int ret = drm_panel_disable(bridge_to_tc358764(bridge)->panel); | 
|  |  | 
|  | if (ret < 0) | 
|  | dev_err(ctx->dev, "error disabling panel (%d)\n", ret); | 
|  | } | 
|  |  | 
|  | static void tc358764_post_disable(struct drm_bridge *bridge) | 
|  | { | 
|  | struct tc358764 *ctx = bridge_to_tc358764(bridge); | 
|  | int ret; | 
|  |  | 
|  | ret = drm_panel_unprepare(ctx->panel); | 
|  | if (ret < 0) | 
|  | dev_err(ctx->dev, "error unpreparing panel (%d)\n", ret); | 
|  | tc358764_reset(ctx); | 
|  | usleep_range(10000, 15000); | 
|  | ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); | 
|  | if (ret < 0) | 
|  | dev_err(ctx->dev, "error disabling regulators (%d)\n", ret); | 
|  | } | 
|  |  | 
|  | static void tc358764_pre_enable(struct drm_bridge *bridge) | 
|  | { | 
|  | struct tc358764 *ctx = bridge_to_tc358764(bridge); | 
|  | int ret; | 
|  |  | 
|  | ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies); | 
|  | if (ret < 0) | 
|  | dev_err(ctx->dev, "error enabling regulators (%d)\n", ret); | 
|  | usleep_range(10000, 15000); | 
|  | tc358764_reset(ctx); | 
|  | ret = tc358764_init(ctx); | 
|  | if (ret < 0) | 
|  | dev_err(ctx->dev, "error initializing bridge (%d)\n", ret); | 
|  | ret = drm_panel_prepare(ctx->panel); | 
|  | if (ret < 0) | 
|  | dev_err(ctx->dev, "error preparing panel (%d)\n", ret); | 
|  | } | 
|  |  | 
|  | static void tc358764_enable(struct drm_bridge *bridge) | 
|  | { | 
|  | struct tc358764 *ctx = bridge_to_tc358764(bridge); | 
|  | int ret = drm_panel_enable(ctx->panel); | 
|  |  | 
|  | if (ret < 0) | 
|  | dev_err(ctx->dev, "error enabling panel (%d)\n", ret); | 
|  | } | 
|  |  | 
|  | static int tc358764_attach(struct drm_bridge *bridge) | 
|  | { | 
|  | struct tc358764 *ctx = bridge_to_tc358764(bridge); | 
|  | struct drm_device *drm = bridge->dev; | 
|  | int ret; | 
|  |  | 
|  | ctx->connector.polled = DRM_CONNECTOR_POLL_HPD; | 
|  | ret = drm_connector_init(drm, &ctx->connector, | 
|  | &tc358764_connector_funcs, | 
|  | DRM_MODE_CONNECTOR_LVDS); | 
|  | if (ret) { | 
|  | DRM_ERROR("Failed to initialize connector\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | drm_connector_helper_add(&ctx->connector, | 
|  | &tc358764_connector_helper_funcs); | 
|  | drm_connector_attach_encoder(&ctx->connector, bridge->encoder); | 
|  | drm_panel_attach(ctx->panel, &ctx->connector); | 
|  | ctx->connector.funcs->reset(&ctx->connector); | 
|  | drm_fb_helper_add_one_connector(drm->fb_helper, &ctx->connector); | 
|  | drm_connector_register(&ctx->connector); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void tc358764_detach(struct drm_bridge *bridge) | 
|  | { | 
|  | struct tc358764 *ctx = bridge_to_tc358764(bridge); | 
|  | struct drm_device *drm = bridge->dev; | 
|  |  | 
|  | drm_connector_unregister(&ctx->connector); | 
|  | drm_fb_helper_remove_one_connector(drm->fb_helper, &ctx->connector); | 
|  | drm_panel_detach(ctx->panel); | 
|  | ctx->panel = NULL; | 
|  | drm_connector_unreference(&ctx->connector); | 
|  | } | 
|  |  | 
|  | static const struct drm_bridge_funcs tc358764_bridge_funcs = { | 
|  | .disable = tc358764_disable, | 
|  | .post_disable = tc358764_post_disable, | 
|  | .enable = tc358764_enable, | 
|  | .pre_enable = tc358764_pre_enable, | 
|  | .attach = tc358764_attach, | 
|  | .detach = tc358764_detach, | 
|  | }; | 
|  |  | 
|  | static int tc358764_parse_dt(struct tc358764 *ctx) | 
|  | { | 
|  | struct device *dev = ctx->dev; | 
|  | int ret; | 
|  |  | 
|  | ctx->gpio_reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); | 
|  | if (IS_ERR(ctx->gpio_reset)) { | 
|  | dev_err(dev, "no reset GPIO pin provided\n"); | 
|  | return PTR_ERR(ctx->gpio_reset); | 
|  | } | 
|  |  | 
|  | ret = drm_of_find_panel_or_bridge(ctx->dev->of_node, 1, 0, &ctx->panel, | 
|  | NULL); | 
|  | if (ret && ret != -EPROBE_DEFER) | 
|  | dev_err(dev, "cannot find panel (%d)\n", ret); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int tc358764_configure_regulators(struct tc358764 *ctx) | 
|  | { | 
|  | int i, ret; | 
|  |  | 
|  | for (i = 0; i < ARRAY_SIZE(ctx->supplies); ++i) | 
|  | ctx->supplies[i].supply = tc358764_supplies[i]; | 
|  |  | 
|  | ret = devm_regulator_bulk_get(ctx->dev, ARRAY_SIZE(ctx->supplies), | 
|  | ctx->supplies); | 
|  | if (ret < 0) | 
|  | dev_err(ctx->dev, "failed to get regulators: %d\n", ret); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int tc358764_probe(struct mipi_dsi_device *dsi) | 
|  | { | 
|  | struct device *dev = &dsi->dev; | 
|  | struct tc358764 *ctx; | 
|  | int ret; | 
|  |  | 
|  | ctx = devm_kzalloc(dev, sizeof(struct tc358764), GFP_KERNEL); | 
|  | if (!ctx) | 
|  | return -ENOMEM; | 
|  |  | 
|  | mipi_dsi_set_drvdata(dsi, ctx); | 
|  |  | 
|  | ctx->dev = dev; | 
|  |  | 
|  | dsi->lanes = 4; | 
|  | dsi->format = MIPI_DSI_FMT_RGB888; | 
|  | dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | 
|  | | MIPI_DSI_MODE_VIDEO_AUTO_VERT | MIPI_DSI_MODE_LPM; | 
|  |  | 
|  | ret = tc358764_parse_dt(ctx); | 
|  | if (ret < 0) | 
|  | return ret; | 
|  |  | 
|  | ret = tc358764_configure_regulators(ctx); | 
|  | if (ret < 0) | 
|  | return ret; | 
|  |  | 
|  | ctx->bridge.funcs = &tc358764_bridge_funcs; | 
|  | ctx->bridge.of_node = dev->of_node; | 
|  |  | 
|  | drm_bridge_add(&ctx->bridge); | 
|  |  | 
|  | ret = mipi_dsi_attach(dsi); | 
|  | if (ret < 0) { | 
|  | drm_bridge_remove(&ctx->bridge); | 
|  | dev_err(dev, "failed to attach dsi\n"); | 
|  | } | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int tc358764_remove(struct mipi_dsi_device *dsi) | 
|  | { | 
|  | struct tc358764 *ctx = mipi_dsi_get_drvdata(dsi); | 
|  |  | 
|  | mipi_dsi_detach(dsi); | 
|  | drm_bridge_remove(&ctx->bridge); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct of_device_id tc358764_of_match[] = { | 
|  | { .compatible = "toshiba,tc358764" }, | 
|  | { } | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(of, tc358764_of_match); | 
|  |  | 
|  | static struct mipi_dsi_driver tc358764_driver = { | 
|  | .probe = tc358764_probe, | 
|  | .remove = tc358764_remove, | 
|  | .driver = { | 
|  | .name = "tc358764", | 
|  | .owner = THIS_MODULE, | 
|  | .of_match_table = tc358764_of_match, | 
|  | }, | 
|  | }; | 
|  | module_mipi_dsi_driver(tc358764_driver); | 
|  |  | 
|  | MODULE_AUTHOR("Andrzej Hajda <a.hajda@samsung.com>"); | 
|  | MODULE_AUTHOR("Maciej Purski <m.purski@samsung.com>"); | 
|  | MODULE_DESCRIPTION("MIPI-DSI based Driver for TC358764 DSI/LVDS Bridge"); | 
|  | MODULE_LICENSE("GPL v2"); |