| // SPDX-License-Identifier: GPL-2.0+ |
| // |
| // Copyright 2011 Freescale Semiconductor, Inc. |
| // Copyright 2011 Linaro Ltd. |
| |
| /dts-v1/; |
| #include "imx51.dtsi" |
| |
| / { |
| model = "Freescale i.MX51 Babbage Board"; |
| compatible = "fsl,imx51-babbage", "fsl,imx51"; |
| |
| chosen { |
| stdout-path = &uart1; |
| }; |
| |
| memory@90000000 { |
| device_type = "memory"; |
| reg = <0x90000000 0x20000000>; |
| }; |
| |
| ckih1 { |
| clock-frequency = <22579200>; |
| }; |
| |
| clk_osc: clk-osc { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <26000000>; |
| }; |
| |
| clk_osc_gate: clk-osc-gate { |
| compatible = "gpio-gate-clock"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_clk26mhz_osc>; |
| clocks = <&clk_osc>; |
| #clock-cells = <0>; |
| enable-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| clk_audio: clk-audio { |
| compatible = "gpio-gate-clock"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_clk26mhz_audio>; |
| clocks = <&clk_osc_gate>; |
| #clock-cells = <0>; |
| enable-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; |
| }; |
| |
| clk_usb: clk-usb { |
| compatible = "gpio-gate-clock"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_clk26mhz_usb>; |
| clocks = <&clk_osc_gate>; |
| #clock-cells = <0>; |
| enable-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; |
| }; |
| |
| display1: disp1 { |
| compatible = "fsl,imx-parallel-display"; |
| interface-pix-fmt = "rgb24"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ipu_disp1>; |
| display-timings { |
| native-mode = <&timing0>; |
| timing0: dvi { |
| clock-frequency = <65000000>; |
| hactive = <1024>; |
| vactive = <768>; |
| hback-porch = <220>; |
| hfront-porch = <40>; |
| vback-porch = <21>; |
| vfront-porch = <7>; |
| hsync-len = <60>; |
| vsync-len = <10>; |
| }; |
| }; |
| |
| port { |
| display0_in: endpoint { |
| remote-endpoint = <&ipu_di0_disp1>; |
| }; |
| }; |
| }; |
| |
| display2: disp2 { |
| compatible = "fsl,imx-parallel-display"; |
| interface-pix-fmt = "rgb565"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ipu_disp2>; |
| status = "disabled"; |
| display-timings { |
| native-mode = <&timing1>; |
| timing1: claawvga { |
| clock-frequency = <27000000>; |
| hactive = <800>; |
| vactive = <480>; |
| hback-porch = <40>; |
| hfront-porch = <60>; |
| vback-porch = <10>; |
| vfront-porch = <10>; |
| hsync-len = <20>; |
| vsync-len = <10>; |
| hsync-active = <0>; |
| vsync-active = <0>; |
| de-active = <1>; |
| pixelclk-active = <0>; |
| }; |
| }; |
| |
| port { |
| display1_in: endpoint { |
| remote-endpoint = <&ipu_di1_disp2>; |
| }; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_keys>; |
| |
| power { |
| label = "Power Button"; |
| gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; |
| linux,code = <KEY_POWER>; |
| wakeup-source; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_leds>; |
| |
| led-diagnostic { |
| label = "diagnostic"; |
| gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| regulators { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| reg_hub_reset: regulator@0 { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotgreg>; |
| reg = <0>; |
| regulator-name = "hub_reset"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| sound { |
| compatible = "fsl,imx51-babbage-sgtl5000", |
| "fsl,imx-audio-sgtl5000"; |
| model = "imx51-babbage-sgtl5000"; |
| ssi-controller = <&ssi2>; |
| audio-codec = <&sgtl5000>; |
| audio-routing = |
| "MIC_IN", "Mic Jack", |
| "Mic Jack", "Mic Bias", |
| "Headphone Jack", "HP_OUT"; |
| mux-int-port = <2>; |
| mux-ext-port = <3>; |
| }; |
| |
| usbphy1: usbphy1 { |
| compatible = "usb-nop-xceiv"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbh1reg>; |
| clocks = <&clk_usb>; |
| clock-names = "main_clk"; |
| reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; |
| vcc-supply = <&vusb_reg>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| &audmux { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_audmux>; |
| status = "okay"; |
| }; |
| |
| &ecspi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi1>; |
| cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>, |
| <&gpio4 25 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| |
| pmic: mc13892@0 { |
| compatible = "fsl,mc13892"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pmic>; |
| spi-max-frequency = <6000000>; |
| spi-cs-high; |
| reg = <0>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,mc13xxx-uses-adc; |
| fsl,mc13xxx-uses-rtc; |
| |
| regulators { |
| sw1_reg: sw1 { |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <1375000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw2_reg: sw2 { |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1850000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw3_reg: sw3 { |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1850000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw4_reg: sw4 { |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1850000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vpll_reg: vpll { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vdig_reg: vdig { |
| regulator-min-microvolt = <1650000>; |
| regulator-max-microvolt = <1650000>; |
| regulator-boot-on; |
| }; |
| |
| vsd_reg: vsd { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3150000>; |
| }; |
| |
| vusb_reg: vusb { |
| regulator-boot-on; |
| }; |
| |
| vusb2_reg: vusb2 { |
| regulator-min-microvolt = <2400000>; |
| regulator-max-microvolt = <2775000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vvideo_reg: vvideo { |
| regulator-min-microvolt = <2775000>; |
| regulator-max-microvolt = <2775000>; |
| }; |
| |
| vaudio_reg: vaudio { |
| regulator-min-microvolt = <2300000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| vcam_reg: vcam { |
| regulator-min-microvolt = <2500000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| vgen1_reg: vgen1 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| vgen2_reg: vgen2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <3150000>; |
| regulator-always-on; |
| }; |
| |
| vgen3_reg: vgen3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2900000>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| flash: at45db321d@1 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash"; |
| spi-max-frequency = <25000000>; |
| reg = <1>; |
| |
| partition@0 { |
| label = "U-Boot"; |
| reg = <0x0 0x40000>; |
| read-only; |
| }; |
| |
| partition@40000 { |
| label = "Kernel"; |
| reg = <0x40000 0x3c0000>; |
| }; |
| }; |
| }; |
| |
| &esdhc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_esdhc1>; |
| cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| &esdhc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_esdhc2>; |
| cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec>; |
| phy-mode = "mii"; |
| phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; |
| phy-reset-duration = <1>; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| |
| sgtl5000: codec@a { |
| compatible = "fsl,sgtl5000"; |
| reg = <0x0a>; |
| #sound-dai-cells = <0>; |
| clocks = <&clk_audio>; |
| VDDA-supply = <&vdig_reg>; |
| VDDIO-supply = <&vvideo_reg>; |
| }; |
| }; |
| |
| &ipu_di0_disp1 { |
| remote-endpoint = <&display0_in>; |
| }; |
| |
| &ipu_di1_disp2 { |
| remote-endpoint = <&display1_in>; |
| }; |
| |
| &kpp { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_kpp>; |
| linux,keymap = < |
| MATRIX_KEY(0, 0, KEY_UP) |
| MATRIX_KEY(0, 1, KEY_DOWN) |
| MATRIX_KEY(0, 2, KEY_VOLUMEDOWN) |
| MATRIX_KEY(0, 3, KEY_HOME) |
| MATRIX_KEY(1, 0, KEY_RIGHT) |
| MATRIX_KEY(1, 1, KEY_LEFT) |
| MATRIX_KEY(1, 2, KEY_ENTER) |
| MATRIX_KEY(1, 3, KEY_VOLUMEUP) |
| MATRIX_KEY(2, 0, KEY_F6) |
| MATRIX_KEY(2, 1, KEY_F8) |
| MATRIX_KEY(2, 2, KEY_F9) |
| MATRIX_KEY(2, 3, KEY_F10) |
| MATRIX_KEY(3, 0, KEY_F1) |
| MATRIX_KEY(3, 1, KEY_F2) |
| MATRIX_KEY(3, 2, KEY_F3) |
| MATRIX_KEY(3, 3, KEY_POWER) |
| >; |
| status = "okay"; |
| }; |
| |
| &pmu { |
| secure-reg-access; |
| }; |
| |
| &ssi2 { |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| uart-has-rtscts; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| uart-has-rtscts; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbh1>; |
| vbus-supply = <®_hub_reset>; |
| fsl,usbphy = <&usbphy1>; |
| phy_type = "ulpi"; |
| status = "okay"; |
| }; |
| |
| &usbphy0 { |
| vcc-supply = <&vusb_reg>; |
| }; |
| |
| &usbotg { |
| dr_mode = "otg"; |
| disable-over-current; |
| phy_type = "utmi_wide"; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| imx51-babbage { |
| pinctrl_audmux: audmuxgrp { |
| fsl,pins = < |
| MX51_PAD_AUD3_BB_TXD__AUD3_TXD 0x80000000 |
| MX51_PAD_AUD3_BB_RXD__AUD3_RXD 0x80000000 |
| MX51_PAD_AUD3_BB_CK__AUD3_TXC 0x80000000 |
| MX51_PAD_AUD3_BB_FS__AUD3_TXFS 0x80000000 |
| >; |
| }; |
| |
| pinctrl_clk26mhz_audio: clk26mhzaudiocgrp { |
| fsl,pins = < |
| MX51_PAD_CSPI1_RDY__GPIO4_26 0x85 |
| >; |
| }; |
| |
| pinctrl_clk26mhz_osc: clk26mhzoscgrp { |
| fsl,pins = < |
| MX51_PAD_DI1_PIN12__GPIO3_1 0x85 |
| >; |
| }; |
| |
| pinctrl_clk26mhz_usb: clk26mhzusbgrp { |
| fsl,pins = < |
| MX51_PAD_EIM_D17__GPIO2_1 0x85 |
| >; |
| }; |
| |
| pinctrl_ecspi1: ecspi1grp { |
| fsl,pins = < |
| MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185 |
| MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185 |
| MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185 |
| MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 /* CS0 */ |
| MX51_PAD_CSPI1_SS1__GPIO4_25 0x85 /* CS1 */ |
| >; |
| }; |
| |
| pinctrl_esdhc1: esdhc1grp { |
| fsl,pins = < |
| MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5 |
| MX51_PAD_SD1_CLK__SD1_CLK 0x20d5 |
| MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5 |
| MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5 |
| MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5 |
| MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5 |
| MX51_PAD_GPIO1_0__GPIO1_0 0x100 |
| MX51_PAD_GPIO1_1__GPIO1_1 0x100 |
| >; |
| }; |
| |
| pinctrl_esdhc2: esdhc2grp { |
| fsl,pins = < |
| MX51_PAD_SD2_CMD__SD2_CMD 0x400020d5 |
| MX51_PAD_SD2_CLK__SD2_CLK 0x20d5 |
| MX51_PAD_SD2_DATA0__SD2_DATA0 0x20d5 |
| MX51_PAD_SD2_DATA1__SD2_DATA1 0x20d5 |
| MX51_PAD_SD2_DATA2__SD2_DATA2 0x20d5 |
| MX51_PAD_SD2_DATA3__SD2_DATA3 0x20d5 |
| MX51_PAD_GPIO1_5__GPIO1_5 0x100 /* WP */ |
| MX51_PAD_GPIO1_6__GPIO1_6 0x100 /* CD */ |
| >; |
| }; |
| |
| pinctrl_fec: fecgrp { |
| fsl,pins = < |
| MX51_PAD_EIM_EB2__FEC_MDIO 0x000001f5 |
| MX51_PAD_EIM_EB3__FEC_RDATA1 0x00000085 |
| MX51_PAD_EIM_CS2__FEC_RDATA2 0x00000085 |
| MX51_PAD_EIM_CS3__FEC_RDATA3 0x00000085 |
| MX51_PAD_EIM_CS4__FEC_RX_ER 0x00000180 |
| MX51_PAD_EIM_CS5__FEC_CRS 0x00000180 |
| MX51_PAD_NANDF_RB2__FEC_COL 0x00000180 |
| MX51_PAD_NANDF_RB3__FEC_RX_CLK 0x00000180 |
| MX51_PAD_NANDF_D9__FEC_RDATA0 0x00002180 |
| MX51_PAD_NANDF_D8__FEC_TDATA0 0x00002004 |
| MX51_PAD_NANDF_CS2__FEC_TX_ER 0x00002004 |
| MX51_PAD_NANDF_CS3__FEC_MDC 0x00002004 |
| MX51_PAD_NANDF_CS4__FEC_TDATA1 0x00002004 |
| MX51_PAD_NANDF_CS5__FEC_TDATA2 0x00002004 |
| MX51_PAD_NANDF_CS6__FEC_TDATA3 0x00002004 |
| MX51_PAD_NANDF_CS7__FEC_TX_EN 0x00002004 |
| MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK 0x00002180 |
| MX51_PAD_NANDF_D11__FEC_RX_DV 0x000020a4 |
| MX51_PAD_EIM_A20__GPIO2_14 0x00000085 /* Phy Reset */ |
| >; |
| }; |
| |
| pinctrl_gpio_keys: gpiokeysgrp { |
| fsl,pins = < |
| MX51_PAD_EIM_A27__GPIO2_21 0x5 |
| >; |
| }; |
| |
| pinctrl_gpio_leds: gpioledsgrp { |
| fsl,pins = < |
| MX51_PAD_EIM_D22__GPIO2_6 0x80000000 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX51_PAD_EIM_D19__I2C1_SCL 0x400001ed |
| MX51_PAD_EIM_D16__I2C1_SDA 0x400001ed |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX51_PAD_KEY_COL4__I2C2_SCL 0x400001ed |
| MX51_PAD_KEY_COL5__I2C2_SDA 0x400001ed |
| >; |
| }; |
| |
| pinctrl_ipu_disp1: ipudisp1grp { |
| fsl,pins = < |
| MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5 |
| MX51_PAD_DISP1_DAT1__DISP1_DAT1 0x5 |
| MX51_PAD_DISP1_DAT2__DISP1_DAT2 0x5 |
| MX51_PAD_DISP1_DAT3__DISP1_DAT3 0x5 |
| MX51_PAD_DISP1_DAT4__DISP1_DAT4 0x5 |
| MX51_PAD_DISP1_DAT5__DISP1_DAT5 0x5 |
| MX51_PAD_DISP1_DAT6__DISP1_DAT6 0x5 |
| MX51_PAD_DISP1_DAT7__DISP1_DAT7 0x5 |
| MX51_PAD_DISP1_DAT8__DISP1_DAT8 0x5 |
| MX51_PAD_DISP1_DAT9__DISP1_DAT9 0x5 |
| MX51_PAD_DISP1_DAT10__DISP1_DAT10 0x5 |
| MX51_PAD_DISP1_DAT11__DISP1_DAT11 0x5 |
| MX51_PAD_DISP1_DAT12__DISP1_DAT12 0x5 |
| MX51_PAD_DISP1_DAT13__DISP1_DAT13 0x5 |
| MX51_PAD_DISP1_DAT14__DISP1_DAT14 0x5 |
| MX51_PAD_DISP1_DAT15__DISP1_DAT15 0x5 |
| MX51_PAD_DISP1_DAT16__DISP1_DAT16 0x5 |
| MX51_PAD_DISP1_DAT17__DISP1_DAT17 0x5 |
| MX51_PAD_DISP1_DAT18__DISP1_DAT18 0x5 |
| MX51_PAD_DISP1_DAT19__DISP1_DAT19 0x5 |
| MX51_PAD_DISP1_DAT20__DISP1_DAT20 0x5 |
| MX51_PAD_DISP1_DAT21__DISP1_DAT21 0x5 |
| MX51_PAD_DISP1_DAT22__DISP1_DAT22 0x5 |
| MX51_PAD_DISP1_DAT23__DISP1_DAT23 0x5 |
| MX51_PAD_DI1_PIN2__DI1_PIN2 0x5 |
| MX51_PAD_DI1_PIN3__DI1_PIN3 0x5 |
| >; |
| }; |
| |
| pinctrl_ipu_disp2: ipudisp2grp { |
| fsl,pins = < |
| MX51_PAD_DISP2_DAT0__DISP2_DAT0 0x5 |
| MX51_PAD_DISP2_DAT1__DISP2_DAT1 0x5 |
| MX51_PAD_DISP2_DAT2__DISP2_DAT2 0x5 |
| MX51_PAD_DISP2_DAT3__DISP2_DAT3 0x5 |
| MX51_PAD_DISP2_DAT4__DISP2_DAT4 0x5 |
| MX51_PAD_DISP2_DAT5__DISP2_DAT5 0x5 |
| MX51_PAD_DISP2_DAT6__DISP2_DAT6 0x5 |
| MX51_PAD_DISP2_DAT7__DISP2_DAT7 0x5 |
| MX51_PAD_DISP2_DAT8__DISP2_DAT8 0x5 |
| MX51_PAD_DISP2_DAT9__DISP2_DAT9 0x5 |
| MX51_PAD_DISP2_DAT10__DISP2_DAT10 0x5 |
| MX51_PAD_DISP2_DAT11__DISP2_DAT11 0x5 |
| MX51_PAD_DISP2_DAT12__DISP2_DAT12 0x5 |
| MX51_PAD_DISP2_DAT13__DISP2_DAT13 0x5 |
| MX51_PAD_DISP2_DAT14__DISP2_DAT14 0x5 |
| MX51_PAD_DISP2_DAT15__DISP2_DAT15 0x5 |
| MX51_PAD_DI2_PIN2__DI2_PIN2 0x5 |
| MX51_PAD_DI2_PIN3__DI2_PIN3 0x5 |
| MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK 0x5 |
| MX51_PAD_DI_GP4__DI2_PIN15 0x5 |
| >; |
| }; |
| |
| pinctrl_kpp: kppgrp { |
| fsl,pins = < |
| MX51_PAD_KEY_ROW0__KEY_ROW0 0xe0 |
| MX51_PAD_KEY_ROW1__KEY_ROW1 0xe0 |
| MX51_PAD_KEY_ROW2__KEY_ROW2 0xe0 |
| MX51_PAD_KEY_ROW3__KEY_ROW3 0xe0 |
| MX51_PAD_KEY_COL0__KEY_COL0 0xe8 |
| MX51_PAD_KEY_COL1__KEY_COL1 0xe8 |
| MX51_PAD_KEY_COL2__KEY_COL2 0xe8 |
| MX51_PAD_KEY_COL3__KEY_COL3 0xe8 |
| >; |
| }; |
| |
| pinctrl_pmic: pmicgrp { |
| fsl,pins = < |
| MX51_PAD_GPIO1_8__GPIO1_8 0xe5 /* IRQ */ |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 |
| MX51_PAD_UART1_TXD__UART1_TXD 0x1c5 |
| MX51_PAD_UART1_RTS__UART1_RTS 0x1c5 |
| MX51_PAD_UART1_CTS__UART1_CTS 0x1c5 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX51_PAD_UART2_RXD__UART2_RXD 0x1c5 |
| MX51_PAD_UART2_TXD__UART2_TXD 0x1c5 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX51_PAD_EIM_D25__UART3_RXD 0x1c5 |
| MX51_PAD_EIM_D26__UART3_TXD 0x1c5 |
| MX51_PAD_EIM_D27__UART3_RTS 0x1c5 |
| MX51_PAD_EIM_D24__UART3_CTS 0x1c5 |
| >; |
| }; |
| |
| pinctrl_usbh1: usbh1grp { |
| fsl,pins = < |
| MX51_PAD_USBH1_CLK__USBH1_CLK 0x80000000 |
| MX51_PAD_USBH1_DIR__USBH1_DIR 0x80000000 |
| MX51_PAD_USBH1_NXT__USBH1_NXT 0x80000000 |
| MX51_PAD_USBH1_DATA0__USBH1_DATA0 0x80000000 |
| MX51_PAD_USBH1_DATA1__USBH1_DATA1 0x80000000 |
| MX51_PAD_USBH1_DATA2__USBH1_DATA2 0x80000000 |
| MX51_PAD_USBH1_DATA3__USBH1_DATA3 0x80000000 |
| MX51_PAD_USBH1_DATA4__USBH1_DATA4 0x80000000 |
| MX51_PAD_USBH1_DATA5__USBH1_DATA5 0x80000000 |
| MX51_PAD_USBH1_DATA6__USBH1_DATA6 0x80000000 |
| MX51_PAD_USBH1_DATA7__USBH1_DATA7 0x80000000 |
| >; |
| }; |
| |
| pinctrl_usbh1reg: usbh1reggrp { |
| fsl,pins = < |
| MX51_PAD_EIM_D21__GPIO2_5 0x85 |
| >; |
| }; |
| |
| pinctrl_usbotgreg: usbotgreggrp { |
| fsl,pins = < |
| MX51_PAD_GPIO1_7__GPIO1_7 0x85 |
| >; |
| }; |
| }; |
| }; |
