| /* |
| * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org> |
| * Parts of this file were based on sources as follows: |
| * |
| * Copyright (C) 2006-2008 Intel Corporation |
| * Copyright (C) 2007 Amos Lee <amos_lee@storlinksemi.com> |
| * Copyright (C) 2007 Dave Airlie <airlied@linux.ie> |
| * Copyright (C) 2011 Texas Instruments |
| * Copyright (C) 2017 Eric Anholt |
| * |
| * This program is free software and is provided to you under the terms of the |
| * GNU General Public License version 2 as published by the Free Software |
| * Foundation, and any use by you of this program is subject to the terms of |
| * such GNU licence. |
| */ |
| #include <linux/clk.h> |
| #include <linux/version.h> |
| #include <linux/dma-buf.h> |
| #include <linux/of_graph.h> |
| |
| #include <drm/drmP.h> |
| #include <drm/drm_panel.h> |
| #include <drm/drm_gem_cma_helper.h> |
| #include <drm/drm_gem_framebuffer_helper.h> |
| #include <drm/drm_fb_cma_helper.h> |
| |
| #include "tve200_drm.h" |
| |
| irqreturn_t tve200_irq(int irq, void *data) |
| { |
| struct tve200_drm_dev_private *priv = data; |
| u32 stat; |
| u32 val; |
| |
| stat = readl(priv->regs + TVE200_INT_STAT); |
| |
| if (!stat) |
| return IRQ_NONE; |
| |
| /* |
| * Vblank IRQ |
| * |
| * The hardware is a bit tilted: the line stays high after clearing |
| * the vblank IRQ, firing many more interrupts. We counter this |
| * by toggling the IRQ back and forth from firing at vblank and |
| * firing at start of active image, which works around the problem |
| * since those occur strictly in sequence, and we get two IRQs for each |
| * frame, one at start of Vblank (that we make call into the CRTC) and |
| * another one at the start of the image (that we discard). |
| */ |
| if (stat & TVE200_INT_V_STATUS) { |
| val = readl(priv->regs + TVE200_CTRL); |
| /* We have an actual start of vsync */ |
| if (!(val & TVE200_VSTSTYPE_BITS)) { |
| drm_crtc_handle_vblank(&priv->pipe.crtc); |
| /* Toggle trigger to start of active image */ |
| val |= TVE200_VSTSTYPE_VAI; |
| } else { |
| /* Toggle trigger back to start of vsync */ |
| val &= ~TVE200_VSTSTYPE_BITS; |
| } |
| writel(val, priv->regs + TVE200_CTRL); |
| } else |
| dev_err(priv->drm->dev, "stray IRQ %08x\n", stat); |
| |
| /* Clear the interrupt once done */ |
| writel(stat, priv->regs + TVE200_INT_CLR); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int tve200_display_check(struct drm_simple_display_pipe *pipe, |
| struct drm_plane_state *pstate, |
| struct drm_crtc_state *cstate) |
| { |
| const struct drm_display_mode *mode = &cstate->mode; |
| struct drm_framebuffer *old_fb = pipe->plane.state->fb; |
| struct drm_framebuffer *fb = pstate->fb; |
| |
| /* |
| * We support these specific resolutions and nothing else. |
| */ |
| if (!(mode->hdisplay == 352 && mode->vdisplay == 240) && /* SIF(525) */ |
| !(mode->hdisplay == 352 && mode->vdisplay == 288) && /* CIF(625) */ |
| !(mode->hdisplay == 640 && mode->vdisplay == 480) && /* VGA */ |
| !(mode->hdisplay == 720 && mode->vdisplay == 480) && /* D1 */ |
| !(mode->hdisplay == 720 && mode->vdisplay == 576)) { /* D1 */ |
| DRM_DEBUG_KMS("unsupported display mode (%u x %u)\n", |
| mode->hdisplay, mode->vdisplay); |
| return -EINVAL; |
| } |
| |
| if (fb) { |
| u32 offset = drm_fb_cma_get_gem_addr(fb, pstate, 0); |
| |
| /* FB base address must be dword aligned. */ |
| if (offset & 3) { |
| DRM_DEBUG_KMS("FB not 32-bit aligned\n"); |
| return -EINVAL; |
| } |
| |
| /* |
| * There's no pitch register, the mode's hdisplay |
| * controls this. |
| */ |
| if (fb->pitches[0] != mode->hdisplay * fb->format->cpp[0]) { |
| DRM_DEBUG_KMS("can't handle pitches\n"); |
| return -EINVAL; |
| } |
| |
| /* |
| * We can't change the FB format in a flicker-free |
| * manner (and only update it during CRTC enable). |
| */ |
| if (old_fb && old_fb->format != fb->format) |
| cstate->mode_changed = true; |
| } |
| |
| return 0; |
| } |
| |
| static void tve200_display_enable(struct drm_simple_display_pipe *pipe, |
| struct drm_crtc_state *cstate, |
| struct drm_plane_state *plane_state) |
| { |
| struct drm_crtc *crtc = &pipe->crtc; |
| struct drm_plane *plane = &pipe->plane; |
| struct drm_device *drm = crtc->dev; |
| struct tve200_drm_dev_private *priv = drm->dev_private; |
| const struct drm_display_mode *mode = &cstate->mode; |
| struct drm_framebuffer *fb = plane->state->fb; |
| struct drm_connector *connector = priv->connector; |
| u32 format = fb->format->format; |
| u32 ctrl1 = 0; |
| |
| clk_prepare_enable(priv->clk); |
| |
| /* Function 1 */ |
| ctrl1 |= TVE200_CTRL_CSMODE; |
| /* Interlace mode for CCIR656: parameterize? */ |
| ctrl1 |= TVE200_CTRL_NONINTERLACE; |
| /* 32 words per burst */ |
| ctrl1 |= TVE200_CTRL_BURST_32_WORDS; |
| /* 16 retries */ |
| ctrl1 |= TVE200_CTRL_RETRYCNT_16; |
| /* NTSC mode: parametrize? */ |
| ctrl1 |= TVE200_CTRL_NTSC; |
| |
| /* Vsync IRQ at start of Vsync at first */ |
| ctrl1 |= TVE200_VSTSTYPE_VSYNC; |
| |
| if (connector->display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_NEGEDGE) |
| ctrl1 |= TVE200_CTRL_TVCLKP; |
| |
| if ((mode->hdisplay == 352 && mode->vdisplay == 240) || /* SIF(525) */ |
| (mode->hdisplay == 352 && mode->vdisplay == 288)) { /* CIF(625) */ |
| ctrl1 |= TVE200_CTRL_IPRESOL_CIF; |
| dev_info(drm->dev, "CIF mode\n"); |
| } else if (mode->hdisplay == 640 && mode->vdisplay == 480) { |
| ctrl1 |= TVE200_CTRL_IPRESOL_VGA; |
| dev_info(drm->dev, "VGA mode\n"); |
| } else if ((mode->hdisplay == 720 && mode->vdisplay == 480) || |
| (mode->hdisplay == 720 && mode->vdisplay == 576)) { |
| ctrl1 |= TVE200_CTRL_IPRESOL_D1; |
| dev_info(drm->dev, "D1 mode\n"); |
| } |
| |
| if (format & DRM_FORMAT_BIG_ENDIAN) { |
| ctrl1 |= TVE200_CTRL_BBBP; |
| format &= ~DRM_FORMAT_BIG_ENDIAN; |
| } |
| |
| switch (format) { |
| case DRM_FORMAT_XRGB8888: |
| ctrl1 |= TVE200_IPDMOD_RGB888; |
| break; |
| case DRM_FORMAT_RGB565: |
| ctrl1 |= TVE200_IPDMOD_RGB565; |
| break; |
| case DRM_FORMAT_XRGB1555: |
| ctrl1 |= TVE200_IPDMOD_RGB555; |
| break; |
| case DRM_FORMAT_XBGR8888: |
| ctrl1 |= TVE200_IPDMOD_RGB888 | TVE200_BGR; |
| break; |
| case DRM_FORMAT_BGR565: |
| ctrl1 |= TVE200_IPDMOD_RGB565 | TVE200_BGR; |
| break; |
| case DRM_FORMAT_XBGR1555: |
| ctrl1 |= TVE200_IPDMOD_RGB555 | TVE200_BGR; |
| break; |
| case DRM_FORMAT_YUYV: |
| ctrl1 |= TVE200_IPDMOD_YUV422; |
| ctrl1 |= TVE200_CTRL_YCBCRODR_CR0Y1CB0Y0; |
| break; |
| case DRM_FORMAT_YVYU: |
| ctrl1 |= TVE200_IPDMOD_YUV422; |
| ctrl1 |= TVE200_CTRL_YCBCRODR_CB0Y1CR0Y0; |
| break; |
| case DRM_FORMAT_UYVY: |
| ctrl1 |= TVE200_IPDMOD_YUV422; |
| ctrl1 |= TVE200_CTRL_YCBCRODR_Y1CR0Y0CB0; |
| break; |
| case DRM_FORMAT_VYUY: |
| ctrl1 |= TVE200_IPDMOD_YUV422; |
| ctrl1 |= TVE200_CTRL_YCBCRODR_Y1CB0Y0CR0; |
| break; |
| case DRM_FORMAT_YUV420: |
| ctrl1 |= TVE200_CTRL_YUV420; |
| ctrl1 |= TVE200_IPDMOD_YUV420; |
| break; |
| default: |
| dev_err(drm->dev, "Unknown FB format 0x%08x\n", |
| fb->format->format); |
| break; |
| } |
| |
| ctrl1 |= TVE200_TVEEN; |
| |
| /* Turn it on */ |
| writel(ctrl1, priv->regs + TVE200_CTRL); |
| |
| drm_crtc_vblank_on(crtc); |
| } |
| |
| static void tve200_display_disable(struct drm_simple_display_pipe *pipe) |
| { |
| struct drm_crtc *crtc = &pipe->crtc; |
| struct drm_device *drm = crtc->dev; |
| struct tve200_drm_dev_private *priv = drm->dev_private; |
| |
| drm_crtc_vblank_off(crtc); |
| |
| /* Disable and Power Down */ |
| writel(0, priv->regs + TVE200_CTRL); |
| |
| clk_disable_unprepare(priv->clk); |
| } |
| |
| static void tve200_display_update(struct drm_simple_display_pipe *pipe, |
| struct drm_plane_state *old_pstate) |
| { |
| struct drm_crtc *crtc = &pipe->crtc; |
| struct drm_device *drm = crtc->dev; |
| struct tve200_drm_dev_private *priv = drm->dev_private; |
| struct drm_pending_vblank_event *event = crtc->state->event; |
| struct drm_plane *plane = &pipe->plane; |
| struct drm_plane_state *pstate = plane->state; |
| struct drm_framebuffer *fb = pstate->fb; |
| |
| if (fb) { |
| /* For RGB, the Y component is used as base address */ |
| writel(drm_fb_cma_get_gem_addr(fb, pstate, 0), |
| priv->regs + TVE200_Y_FRAME_BASE_ADDR); |
| |
| /* For three plane YUV we need two more addresses */ |
| if (fb->format->format == DRM_FORMAT_YUV420) { |
| writel(drm_fb_cma_get_gem_addr(fb, pstate, 1), |
| priv->regs + TVE200_U_FRAME_BASE_ADDR); |
| writel(drm_fb_cma_get_gem_addr(fb, pstate, 2), |
| priv->regs + TVE200_V_FRAME_BASE_ADDR); |
| } |
| } |
| |
| if (event) { |
| crtc->state->event = NULL; |
| |
| spin_lock_irq(&crtc->dev->event_lock); |
| if (crtc->state->active && drm_crtc_vblank_get(crtc) == 0) |
| drm_crtc_arm_vblank_event(crtc, event); |
| else |
| drm_crtc_send_vblank_event(crtc, event); |
| spin_unlock_irq(&crtc->dev->event_lock); |
| } |
| } |
| |
| static int tve200_display_enable_vblank(struct drm_simple_display_pipe *pipe) |
| { |
| struct drm_crtc *crtc = &pipe->crtc; |
| struct drm_device *drm = crtc->dev; |
| struct tve200_drm_dev_private *priv = drm->dev_private; |
| |
| writel(TVE200_INT_V_STATUS, priv->regs + TVE200_INT_EN); |
| return 0; |
| } |
| |
| static void tve200_display_disable_vblank(struct drm_simple_display_pipe *pipe) |
| { |
| struct drm_crtc *crtc = &pipe->crtc; |
| struct drm_device *drm = crtc->dev; |
| struct tve200_drm_dev_private *priv = drm->dev_private; |
| |
| writel(0, priv->regs + TVE200_INT_EN); |
| } |
| |
| static const struct drm_simple_display_pipe_funcs tve200_display_funcs = { |
| .check = tve200_display_check, |
| .enable = tve200_display_enable, |
| .disable = tve200_display_disable, |
| .update = tve200_display_update, |
| .prepare_fb = drm_gem_fb_simple_display_pipe_prepare_fb, |
| .enable_vblank = tve200_display_enable_vblank, |
| .disable_vblank = tve200_display_disable_vblank, |
| }; |
| |
| int tve200_display_init(struct drm_device *drm) |
| { |
| struct tve200_drm_dev_private *priv = drm->dev_private; |
| int ret; |
| static const u32 formats[] = { |
| DRM_FORMAT_XRGB8888, |
| DRM_FORMAT_XBGR8888, |
| DRM_FORMAT_RGB565, |
| DRM_FORMAT_BGR565, |
| DRM_FORMAT_XRGB1555, |
| DRM_FORMAT_XBGR1555, |
| /* |
| * The controller actually supports any YCbCr ordering, |
| * for packed YCbCr. This just lists the orderings that |
| * DRM supports. |
| */ |
| DRM_FORMAT_YUYV, |
| DRM_FORMAT_YVYU, |
| DRM_FORMAT_UYVY, |
| DRM_FORMAT_VYUY, |
| /* This uses three planes */ |
| DRM_FORMAT_YUV420, |
| }; |
| |
| ret = drm_simple_display_pipe_init(drm, &priv->pipe, |
| &tve200_display_funcs, |
| formats, ARRAY_SIZE(formats), |
| NULL, |
| priv->connector); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |