| /* | |
| * FSL SoC setup code | |
| * | |
| * Maintained by Kumar Gala (see MAINTAINERS for contact information) | |
| * | |
| * 2006 (c) MontaVista Software, Inc. | |
| * Vitaly Bordug <vbordug@ru.mvista.com> | |
| * | |
| * This program is free software; you can redistribute it and/or modify it | |
| * under the terms of the GNU General Public License as published by the | |
| * Free Software Foundation; either version 2 of the License, or (at your | |
| * option) any later version. | |
| */ | |
| #include <linux/stddef.h> | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/errno.h> | |
| #include <linux/major.h> | |
| #include <linux/delay.h> | |
| #include <linux/irq.h> | |
| #include <linux/module.h> | |
| #include <linux/device.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/of_platform.h> | |
| #include <linux/phy.h> | |
| #include <linux/phy_fixed.h> | |
| #include <linux/spi/spi.h> | |
| #include <linux/fsl_devices.h> | |
| #include <linux/fs_enet_pd.h> | |
| #include <linux/fs_uart_pd.h> | |
| #include <asm/system.h> | |
| #include <asm/atomic.h> | |
| #include <asm/io.h> | |
| #include <asm/irq.h> | |
| #include <asm/time.h> | |
| #include <asm/prom.h> | |
| #include <sysdev/fsl_soc.h> | |
| #include <mm/mmu_decl.h> | |
| #include <asm/cpm2.h> | |
| extern void init_fcc_ioports(struct fs_platform_info*); | |
| extern void init_fec_ioports(struct fs_platform_info*); | |
| extern void init_smc_ioports(struct fs_uart_platform_info*); | |
| static phys_addr_t immrbase = -1; | |
| phys_addr_t get_immrbase(void) | |
| { | |
| struct device_node *soc; | |
| if (immrbase != -1) | |
| return immrbase; | |
| soc = of_find_node_by_type(NULL, "soc"); | |
| if (soc) { | |
| int size; | |
| u32 naddr; | |
| const u32 *prop = of_get_property(soc, "#address-cells", &size); | |
| if (prop && size == 4) | |
| naddr = *prop; | |
| else | |
| naddr = 2; | |
| prop = of_get_property(soc, "ranges", &size); | |
| if (prop) | |
| immrbase = of_translate_address(soc, prop + naddr); | |
| of_node_put(soc); | |
| } | |
| return immrbase; | |
| } | |
| EXPORT_SYMBOL(get_immrbase); | |
| static u32 sysfreq = -1; | |
| u32 fsl_get_sys_freq(void) | |
| { | |
| struct device_node *soc; | |
| const u32 *prop; | |
| int size; | |
| if (sysfreq != -1) | |
| return sysfreq; | |
| soc = of_find_node_by_type(NULL, "soc"); | |
| if (!soc) | |
| return -1; | |
| prop = of_get_property(soc, "clock-frequency", &size); | |
| if (!prop || size != sizeof(*prop) || *prop == 0) | |
| prop = of_get_property(soc, "bus-frequency", &size); | |
| if (prop && size == sizeof(*prop)) | |
| sysfreq = *prop; | |
| of_node_put(soc); | |
| return sysfreq; | |
| } | |
| EXPORT_SYMBOL(fsl_get_sys_freq); | |
| #if defined(CONFIG_CPM2) || defined(CONFIG_QUICC_ENGINE) || defined(CONFIG_8xx) | |
| static u32 brgfreq = -1; | |
| u32 get_brgfreq(void) | |
| { | |
| struct device_node *node; | |
| const unsigned int *prop; | |
| int size; | |
| if (brgfreq != -1) | |
| return brgfreq; | |
| node = of_find_compatible_node(NULL, NULL, "fsl,cpm-brg"); | |
| if (node) { | |
| prop = of_get_property(node, "clock-frequency", &size); | |
| if (prop && size == 4) | |
| brgfreq = *prop; | |
| of_node_put(node); | |
| return brgfreq; | |
| } | |
| /* Legacy device binding -- will go away when no users are left. */ | |
| node = of_find_node_by_type(NULL, "cpm"); | |
| if (!node) | |
| node = of_find_compatible_node(NULL, NULL, "fsl,qe"); | |
| if (!node) | |
| node = of_find_node_by_type(NULL, "qe"); | |
| if (node) { | |
| prop = of_get_property(node, "brg-frequency", &size); | |
| if (prop && size == 4) | |
| brgfreq = *prop; | |
| if (brgfreq == -1 || brgfreq == 0) { | |
| prop = of_get_property(node, "bus-frequency", &size); | |
| if (prop && size == 4) | |
| brgfreq = *prop / 2; | |
| } | |
| of_node_put(node); | |
| } | |
| return brgfreq; | |
| } | |
| EXPORT_SYMBOL(get_brgfreq); | |
| static u32 fs_baudrate = -1; | |
| u32 get_baudrate(void) | |
| { | |
| struct device_node *node; | |
| if (fs_baudrate != -1) | |
| return fs_baudrate; | |
| node = of_find_node_by_type(NULL, "serial"); | |
| if (node) { | |
| int size; | |
| const unsigned int *prop = of_get_property(node, | |
| "current-speed", &size); | |
| if (prop) | |
| fs_baudrate = *prop; | |
| of_node_put(node); | |
| } | |
| return fs_baudrate; | |
| } | |
| EXPORT_SYMBOL(get_baudrate); | |
| #endif /* CONFIG_CPM2 */ | |
| #ifdef CONFIG_FIXED_PHY | |
| static int __init of_add_fixed_phys(void) | |
| { | |
| int ret; | |
| struct device_node *np; | |
| u32 *fixed_link; | |
| struct fixed_phy_status status = {}; | |
| for_each_node_by_name(np, "ethernet") { | |
| fixed_link = (u32 *)of_get_property(np, "fixed-link", NULL); | |
| if (!fixed_link) | |
| continue; | |
| status.link = 1; | |
| status.duplex = fixed_link[1]; | |
| status.speed = fixed_link[2]; | |
| status.pause = fixed_link[3]; | |
| status.asym_pause = fixed_link[4]; | |
| ret = fixed_phy_add(PHY_POLL, fixed_link[0], &status); | |
| if (ret) { | |
| of_node_put(np); | |
| return ret; | |
| } | |
| } | |
| return 0; | |
| } | |
| arch_initcall(of_add_fixed_phys); | |
| #endif /* CONFIG_FIXED_PHY */ | |
| static int gfar_mdio_of_init_one(struct device_node *np) | |
| { | |
| int k; | |
| struct device_node *child = NULL; | |
| struct gianfar_mdio_data mdio_data; | |
| struct platform_device *mdio_dev; | |
| struct resource res; | |
| int ret; | |
| memset(&res, 0, sizeof(res)); | |
| memset(&mdio_data, 0, sizeof(mdio_data)); | |
| ret = of_address_to_resource(np, 0, &res); | |
| if (ret) | |
| return ret; | |
| /* The gianfar device will try to use the same ID created below to find | |
| * this bus, to coordinate register access (since they share). */ | |
| mdio_dev = platform_device_register_simple("fsl-gianfar_mdio", | |
| res.start&0xfffff, &res, 1); | |
| if (IS_ERR(mdio_dev)) | |
| return PTR_ERR(mdio_dev); | |
| for (k = 0; k < 32; k++) | |
| mdio_data.irq[k] = PHY_POLL; | |
| while ((child = of_get_next_child(np, child)) != NULL) { | |
| int irq = irq_of_parse_and_map(child, 0); | |
| if (irq != NO_IRQ) { | |
| const u32 *id = of_get_property(child, "reg", NULL); | |
| mdio_data.irq[*id] = irq; | |
| } | |
| } | |
| ret = platform_device_add_data(mdio_dev, &mdio_data, | |
| sizeof(struct gianfar_mdio_data)); | |
| if (ret) | |
| platform_device_unregister(mdio_dev); | |
| return ret; | |
| } | |
| static int __init gfar_mdio_of_init(void) | |
| { | |
| struct device_node *np = NULL; | |
| for_each_compatible_node(np, NULL, "fsl,gianfar-mdio") | |
| gfar_mdio_of_init_one(np); | |
| /* try the deprecated version */ | |
| for_each_compatible_node(np, "mdio", "gianfar"); | |
| gfar_mdio_of_init_one(np); | |
| return 0; | |
| } | |
| arch_initcall(gfar_mdio_of_init); | |
| static const char *gfar_tx_intr = "tx"; | |
| static const char *gfar_rx_intr = "rx"; | |
| static const char *gfar_err_intr = "error"; | |
| static int __init gfar_of_init(void) | |
| { | |
| struct device_node *np; | |
| unsigned int i; | |
| struct platform_device *gfar_dev; | |
| struct resource res; | |
| int ret; | |
| for (np = NULL, i = 0; | |
| (np = of_find_compatible_node(np, "network", "gianfar")) != NULL; | |
| i++) { | |
| struct resource r[4]; | |
| struct device_node *phy, *mdio; | |
| struct gianfar_platform_data gfar_data; | |
| const unsigned int *id; | |
| const char *model; | |
| const char *ctype; | |
| const void *mac_addr; | |
| const phandle *ph; | |
| int n_res = 2; | |
| if (!of_device_is_available(np)) | |
| continue; | |
| memset(r, 0, sizeof(r)); | |
| memset(&gfar_data, 0, sizeof(gfar_data)); | |
| ret = of_address_to_resource(np, 0, &r[0]); | |
| if (ret) | |
| goto err; | |
| of_irq_to_resource(np, 0, &r[1]); | |
| model = of_get_property(np, "model", NULL); | |
| /* If we aren't the FEC we have multiple interrupts */ | |
| if (model && strcasecmp(model, "FEC")) { | |
| r[1].name = gfar_tx_intr; | |
| r[2].name = gfar_rx_intr; | |
| of_irq_to_resource(np, 1, &r[2]); | |
| r[3].name = gfar_err_intr; | |
| of_irq_to_resource(np, 2, &r[3]); | |
| n_res += 2; | |
| } | |
| gfar_dev = | |
| platform_device_register_simple("fsl-gianfar", i, &r[0], | |
| n_res); | |
| if (IS_ERR(gfar_dev)) { | |
| ret = PTR_ERR(gfar_dev); | |
| goto err; | |
| } | |
| mac_addr = of_get_mac_address(np); | |
| if (mac_addr) | |
| memcpy(gfar_data.mac_addr, mac_addr, 6); | |
| if (model && !strcasecmp(model, "TSEC")) | |
| gfar_data.device_flags = | |
| FSL_GIANFAR_DEV_HAS_GIGABIT | | |
| FSL_GIANFAR_DEV_HAS_COALESCE | | |
| FSL_GIANFAR_DEV_HAS_RMON | | |
| FSL_GIANFAR_DEV_HAS_MULTI_INTR; | |
| if (model && !strcasecmp(model, "eTSEC")) | |
| gfar_data.device_flags = | |
| FSL_GIANFAR_DEV_HAS_GIGABIT | | |
| FSL_GIANFAR_DEV_HAS_COALESCE | | |
| FSL_GIANFAR_DEV_HAS_RMON | | |
| FSL_GIANFAR_DEV_HAS_MULTI_INTR | | |
| FSL_GIANFAR_DEV_HAS_CSUM | | |
| FSL_GIANFAR_DEV_HAS_VLAN | | |
| FSL_GIANFAR_DEV_HAS_EXTENDED_HASH; | |
| ctype = of_get_property(np, "phy-connection-type", NULL); | |
| /* We only care about rgmii-id. The rest are autodetected */ | |
| if (ctype && !strcmp(ctype, "rgmii-id")) | |
| gfar_data.interface = PHY_INTERFACE_MODE_RGMII_ID; | |
| else | |
| gfar_data.interface = PHY_INTERFACE_MODE_MII; | |
| if (of_get_property(np, "fsl,magic-packet", NULL)) | |
| gfar_data.device_flags |= FSL_GIANFAR_DEV_HAS_MAGIC_PACKET; | |
| ph = of_get_property(np, "phy-handle", NULL); | |
| if (ph == NULL) { | |
| u32 *fixed_link; | |
| fixed_link = (u32 *)of_get_property(np, "fixed-link", | |
| NULL); | |
| if (!fixed_link) { | |
| ret = -ENODEV; | |
| goto unreg; | |
| } | |
| snprintf(gfar_data.bus_id, MII_BUS_ID_SIZE, "0"); | |
| gfar_data.phy_id = fixed_link[0]; | |
| } else { | |
| phy = of_find_node_by_phandle(*ph); | |
| if (phy == NULL) { | |
| ret = -ENODEV; | |
| goto unreg; | |
| } | |
| mdio = of_get_parent(phy); | |
| id = of_get_property(phy, "reg", NULL); | |
| ret = of_address_to_resource(mdio, 0, &res); | |
| if (ret) { | |
| of_node_put(phy); | |
| of_node_put(mdio); | |
| goto unreg; | |
| } | |
| gfar_data.phy_id = *id; | |
| snprintf(gfar_data.bus_id, MII_BUS_ID_SIZE, "%llx", | |
| (unsigned long long)res.start&0xfffff); | |
| of_node_put(phy); | |
| of_node_put(mdio); | |
| } | |
| /* Get MDIO bus controlled by this eTSEC, if any. Normally only | |
| * eTSEC 1 will control an MDIO bus, not necessarily the same | |
| * bus that its PHY is on ('mdio' above), so we can't just use | |
| * that. What we do is look for a gianfar mdio device that has | |
| * overlapping registers with this device. That's really the | |
| * whole point, to find the device sharing our registers to | |
| * coordinate access with it. | |
| */ | |
| for_each_compatible_node(mdio, NULL, "fsl,gianfar-mdio") { | |
| if (of_address_to_resource(mdio, 0, &res)) | |
| continue; | |
| if (res.start >= r[0].start && res.end <= r[0].end) { | |
| /* Get the ID the mdio bus platform device was | |
| * registered with. gfar_data.bus_id is | |
| * different because it's for finding a PHY, | |
| * while this is for finding a MII bus. | |
| */ | |
| gfar_data.mdio_bus = res.start&0xfffff; | |
| of_node_put(mdio); | |
| break; | |
| } | |
| } | |
| ret = | |
| platform_device_add_data(gfar_dev, &gfar_data, | |
| sizeof(struct | |
| gianfar_platform_data)); | |
| if (ret) | |
| goto unreg; | |
| } | |
| return 0; | |
| unreg: | |
| platform_device_unregister(gfar_dev); | |
| err: | |
| return ret; | |
| } | |
| arch_initcall(gfar_of_init); | |
| static enum fsl_usb2_phy_modes determine_usb_phy(const char *phy_type) | |
| { | |
| if (!phy_type) | |
| return FSL_USB2_PHY_NONE; | |
| if (!strcasecmp(phy_type, "ulpi")) | |
| return FSL_USB2_PHY_ULPI; | |
| if (!strcasecmp(phy_type, "utmi")) | |
| return FSL_USB2_PHY_UTMI; | |
| if (!strcasecmp(phy_type, "utmi_wide")) | |
| return FSL_USB2_PHY_UTMI_WIDE; | |
| if (!strcasecmp(phy_type, "serial")) | |
| return FSL_USB2_PHY_SERIAL; | |
| return FSL_USB2_PHY_NONE; | |
| } | |
| static int __init fsl_usb_of_init(void) | |
| { | |
| struct device_node *np; | |
| unsigned int i = 0; | |
| struct platform_device *usb_dev_mph = NULL, *usb_dev_dr_host = NULL, | |
| *usb_dev_dr_client = NULL; | |
| int ret; | |
| for_each_compatible_node(np, NULL, "fsl-usb2-mph") { | |
| struct resource r[2]; | |
| struct fsl_usb2_platform_data usb_data; | |
| const unsigned char *prop = NULL; | |
| memset(&r, 0, sizeof(r)); | |
| memset(&usb_data, 0, sizeof(usb_data)); | |
| ret = of_address_to_resource(np, 0, &r[0]); | |
| if (ret) | |
| goto err; | |
| of_irq_to_resource(np, 0, &r[1]); | |
| usb_dev_mph = | |
| platform_device_register_simple("fsl-ehci", i, r, 2); | |
| if (IS_ERR(usb_dev_mph)) { | |
| ret = PTR_ERR(usb_dev_mph); | |
| goto err; | |
| } | |
| usb_dev_mph->dev.coherent_dma_mask = 0xffffffffUL; | |
| usb_dev_mph->dev.dma_mask = &usb_dev_mph->dev.coherent_dma_mask; | |
| usb_data.operating_mode = FSL_USB2_MPH_HOST; | |
| prop = of_get_property(np, "port0", NULL); | |
| if (prop) | |
| usb_data.port_enables |= FSL_USB2_PORT0_ENABLED; | |
| prop = of_get_property(np, "port1", NULL); | |
| if (prop) | |
| usb_data.port_enables |= FSL_USB2_PORT1_ENABLED; | |
| prop = of_get_property(np, "phy_type", NULL); | |
| usb_data.phy_mode = determine_usb_phy(prop); | |
| ret = | |
| platform_device_add_data(usb_dev_mph, &usb_data, | |
| sizeof(struct | |
| fsl_usb2_platform_data)); | |
| if (ret) | |
| goto unreg_mph; | |
| i++; | |
| } | |
| for_each_compatible_node(np, NULL, "fsl-usb2-dr") { | |
| struct resource r[2]; | |
| struct fsl_usb2_platform_data usb_data; | |
| const unsigned char *prop = NULL; | |
| memset(&r, 0, sizeof(r)); | |
| memset(&usb_data, 0, sizeof(usb_data)); | |
| ret = of_address_to_resource(np, 0, &r[0]); | |
| if (ret) | |
| goto unreg_mph; | |
| of_irq_to_resource(np, 0, &r[1]); | |
| prop = of_get_property(np, "dr_mode", NULL); | |
| if (!prop || !strcmp(prop, "host")) { | |
| usb_data.operating_mode = FSL_USB2_DR_HOST; | |
| usb_dev_dr_host = platform_device_register_simple( | |
| "fsl-ehci", i, r, 2); | |
| if (IS_ERR(usb_dev_dr_host)) { | |
| ret = PTR_ERR(usb_dev_dr_host); | |
| goto err; | |
| } | |
| } else if (prop && !strcmp(prop, "peripheral")) { | |
| usb_data.operating_mode = FSL_USB2_DR_DEVICE; | |
| usb_dev_dr_client = platform_device_register_simple( | |
| "fsl-usb2-udc", i, r, 2); | |
| if (IS_ERR(usb_dev_dr_client)) { | |
| ret = PTR_ERR(usb_dev_dr_client); | |
| goto err; | |
| } | |
| } else if (prop && !strcmp(prop, "otg")) { | |
| usb_data.operating_mode = FSL_USB2_DR_OTG; | |
| usb_dev_dr_host = platform_device_register_simple( | |
| "fsl-ehci", i, r, 2); | |
| if (IS_ERR(usb_dev_dr_host)) { | |
| ret = PTR_ERR(usb_dev_dr_host); | |
| goto err; | |
| } | |
| usb_dev_dr_client = platform_device_register_simple( | |
| "fsl-usb2-udc", i, r, 2); | |
| if (IS_ERR(usb_dev_dr_client)) { | |
| ret = PTR_ERR(usb_dev_dr_client); | |
| goto err; | |
| } | |
| } else { | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| prop = of_get_property(np, "phy_type", NULL); | |
| usb_data.phy_mode = determine_usb_phy(prop); | |
| if (usb_dev_dr_host) { | |
| usb_dev_dr_host->dev.coherent_dma_mask = 0xffffffffUL; | |
| usb_dev_dr_host->dev.dma_mask = &usb_dev_dr_host-> | |
| dev.coherent_dma_mask; | |
| if ((ret = platform_device_add_data(usb_dev_dr_host, | |
| &usb_data, sizeof(struct | |
| fsl_usb2_platform_data)))) | |
| goto unreg_dr; | |
| } | |
| if (usb_dev_dr_client) { | |
| usb_dev_dr_client->dev.coherent_dma_mask = 0xffffffffUL; | |
| usb_dev_dr_client->dev.dma_mask = &usb_dev_dr_client-> | |
| dev.coherent_dma_mask; | |
| if ((ret = platform_device_add_data(usb_dev_dr_client, | |
| &usb_data, sizeof(struct | |
| fsl_usb2_platform_data)))) | |
| goto unreg_dr; | |
| } | |
| i++; | |
| } | |
| return 0; | |
| unreg_dr: | |
| if (usb_dev_dr_host) | |
| platform_device_unregister(usb_dev_dr_host); | |
| if (usb_dev_dr_client) | |
| platform_device_unregister(usb_dev_dr_client); | |
| unreg_mph: | |
| if (usb_dev_mph) | |
| platform_device_unregister(usb_dev_mph); | |
| err: | |
| return ret; | |
| } | |
| arch_initcall(fsl_usb_of_init); | |
| static int __init of_fsl_spi_probe(char *type, char *compatible, u32 sysclk, | |
| struct spi_board_info *board_infos, | |
| unsigned int num_board_infos, | |
| void (*activate_cs)(u8 cs, u8 polarity), | |
| void (*deactivate_cs)(u8 cs, u8 polarity)) | |
| { | |
| struct device_node *np; | |
| unsigned int i = 0; | |
| for_each_compatible_node(np, type, compatible) { | |
| int ret; | |
| unsigned int j; | |
| const void *prop; | |
| struct resource res[2]; | |
| struct platform_device *pdev; | |
| struct fsl_spi_platform_data pdata = { | |
| .activate_cs = activate_cs, | |
| .deactivate_cs = deactivate_cs, | |
| }; | |
| memset(res, 0, sizeof(res)); | |
| pdata.sysclk = sysclk; | |
| prop = of_get_property(np, "reg", NULL); | |
| if (!prop) | |
| goto err; | |
| pdata.bus_num = *(u32 *)prop; | |
| prop = of_get_property(np, "cell-index", NULL); | |
| if (prop) | |
| i = *(u32 *)prop; | |
| prop = of_get_property(np, "mode", NULL); | |
| if (prop && !strcmp(prop, "cpu-qe")) | |
| pdata.qe_mode = 1; | |
| for (j = 0; j < num_board_infos; j++) { | |
| if (board_infos[j].bus_num == pdata.bus_num) | |
| pdata.max_chipselect++; | |
| } | |
| if (!pdata.max_chipselect) | |
| continue; | |
| ret = of_address_to_resource(np, 0, &res[0]); | |
| if (ret) | |
| goto err; | |
| ret = of_irq_to_resource(np, 0, &res[1]); | |
| if (ret == NO_IRQ) | |
| goto err; | |
| pdev = platform_device_alloc("mpc83xx_spi", i); | |
| if (!pdev) | |
| goto err; | |
| ret = platform_device_add_data(pdev, &pdata, sizeof(pdata)); | |
| if (ret) | |
| goto unreg; | |
| ret = platform_device_add_resources(pdev, res, | |
| ARRAY_SIZE(res)); | |
| if (ret) | |
| goto unreg; | |
| ret = platform_device_add(pdev); | |
| if (ret) | |
| goto unreg; | |
| goto next; | |
| unreg: | |
| platform_device_del(pdev); | |
| err: | |
| pr_err("%s: registration failed\n", np->full_name); | |
| next: | |
| i++; | |
| } | |
| return i; | |
| } | |
| int __init fsl_spi_init(struct spi_board_info *board_infos, | |
| unsigned int num_board_infos, | |
| void (*activate_cs)(u8 cs, u8 polarity), | |
| void (*deactivate_cs)(u8 cs, u8 polarity)) | |
| { | |
| u32 sysclk = -1; | |
| int ret; | |
| #ifdef CONFIG_QUICC_ENGINE | |
| /* SPI controller is either clocked from QE or SoC clock */ | |
| sysclk = get_brgfreq(); | |
| #endif | |
| if (sysclk == -1) { | |
| sysclk = fsl_get_sys_freq(); | |
| if (sysclk == -1) | |
| return -ENODEV; | |
| } | |
| ret = of_fsl_spi_probe(NULL, "fsl,spi", sysclk, board_infos, | |
| num_board_infos, activate_cs, deactivate_cs); | |
| if (!ret) | |
| of_fsl_spi_probe("spi", "fsl_spi", sysclk, board_infos, | |
| num_board_infos, activate_cs, deactivate_cs); | |
| return spi_register_board_info(board_infos, num_board_infos); | |
| } | |
| #if defined(CONFIG_PPC_85xx) || defined(CONFIG_PPC_86xx) | |
| static __be32 __iomem *rstcr; | |
| static int __init setup_rstcr(void) | |
| { | |
| struct device_node *np; | |
| np = of_find_node_by_name(NULL, "global-utilities"); | |
| if ((np && of_get_property(np, "fsl,has-rstcr", NULL))) { | |
| const u32 *prop = of_get_property(np, "reg", NULL); | |
| if (prop) { | |
| /* map reset control register | |
| * 0xE00B0 is offset of reset control register | |
| */ | |
| rstcr = ioremap(get_immrbase() + *prop + 0xB0, 0xff); | |
| if (!rstcr) | |
| printk (KERN_EMERG "Error: reset control " | |
| "register not mapped!\n"); | |
| } | |
| } else | |
| printk (KERN_INFO "rstcr compatible register does not exist!\n"); | |
| if (np) | |
| of_node_put(np); | |
| return 0; | |
| } | |
| arch_initcall(setup_rstcr); | |
| void fsl_rstcr_restart(char *cmd) | |
| { | |
| local_irq_disable(); | |
| if (rstcr) | |
| /* set reset control register */ | |
| out_be32(rstcr, 0x2); /* HRESET_REQ */ | |
| while (1) ; | |
| } | |
| #endif | |
| #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE) | |
| struct platform_diu_data_ops diu_ops; | |
| EXPORT_SYMBOL(diu_ops); | |
| #endif |