| * NXP PCA953x I2C GPIO multiplexer |
| |
| Required properties: |
| - compatible: Has to contain one of the following: |
| nxp,pca9505 |
| nxp,pca9534 |
| nxp,pca9535 |
| nxp,pca9536 |
| nxp,pca9537 |
| nxp,pca9538 |
| nxp,pca9539 |
| nxp,pca9554 |
| nxp,pca9555 |
| nxp,pca9556 |
| nxp,pca9557 |
| nxp,pca9574 |
| nxp,pca9575 |
| nxp,pca9698 |
| nxp,pcal6416 |
| nxp,pcal6524 |
| nxp,pcal9555a |
| maxim,max7310 |
| maxim,max7312 |
| maxim,max7313 |
| maxim,max7315 |
| ti,pca6107 |
| ti,pca9536 |
| ti,tca6408 |
| ti,tca6416 |
| ti,tca6424 |
| ti,tca9539 |
| ti,tca9554 |
| onnn,pca9654 |
| exar,xra1202 |
| - gpio-controller: if used as gpio expander. |
| - #gpio-cells: if used as gpio expander. |
| - interrupt-controller: if to be used as interrupt expander. |
| - #interrupt-cells: if to be used as interrupt expander. |
| |
| Optional properties: |
| - interrupts: interrupt specifier for the device's interrupt output. |
| - reset-gpios: GPIO specification for the RESET input. This is an |
| active low signal to the PCA953x. |
| - vcc-supply: power supply regulator. |
| |
| Example: |
| |
| |
| gpio@20 { |
| compatible = "nxp,pca9505"; |
| reg = <0x20>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pca9505>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-parent = <&gpio3>; |
| interrupts = <23 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| |
| Example with Interrupts: |
| |
| |
| gpio99: gpio@22 { |
| compatible = "nxp,pcal6524"; |
| reg = <0x22>; |
| interrupt-parent = <&gpio6>; |
| interrupts = <1 IRQ_TYPE_EDGE_FALLING>; /* gpio6_161 */ |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| vcc-supply = <&vdds_1v8_main>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-line-names = |
| "hdmi-ct-hpd", "hdmi.ls-oe", "p02", "p03", "vibra", "fault2", "p06", "p07", |
| "en-usb", "en-host1", "en-host2", "chg-int", "p14", "p15", "mic-int", "en-modem", |
| "shdn-hs-amp", "chg-status+red", "green", "blue", "en-esata", "fault1", "p26", "p27"; |
| }; |
| |
| ts3a227@3b { |
| compatible = "ti,ts3a227e"; |
| reg = <0x3b>; |
| interrupt-parent = <&gpio99>; |
| interrupts = <14 IRQ_TYPE_EDGE_RISING>; |
| ti,micbias = <0>; /* 2.1V */ |
| }; |
| |
