| /* | |
| * RTC driver for the Armada 38x Marvell SoCs | |
| * | |
| * Copyright (C) 2015 Marvell | |
| * | |
| * Gregory Clement <gregory.clement@free-electrons.com> | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License as | |
| * published by the Free Software Foundation; either version 2 of the | |
| * License, or (at your option) any later version. | |
| * | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/io.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/rtc.h> | |
| #define RTC_STATUS 0x0 | |
| #define RTC_STATUS_ALARM1 BIT(0) | |
| #define RTC_STATUS_ALARM2 BIT(1) | |
| #define RTC_IRQ1_CONF 0x4 | |
| #define RTC_IRQ1_AL_EN BIT(0) | |
| #define RTC_IRQ1_FREQ_EN BIT(1) | |
| #define RTC_IRQ1_FREQ_1HZ BIT(2) | |
| #define RTC_TIME 0xC | |
| #define RTC_ALARM1 0x10 | |
| #define SOC_RTC_INTERRUPT 0x8 | |
| #define SOC_RTC_ALARM1 BIT(0) | |
| #define SOC_RTC_ALARM2 BIT(1) | |
| #define SOC_RTC_ALARM1_MASK BIT(2) | |
| #define SOC_RTC_ALARM2_MASK BIT(3) | |
| struct armada38x_rtc { | |
| struct rtc_device *rtc_dev; | |
| void __iomem *regs; | |
| void __iomem *regs_soc; | |
| spinlock_t lock; | |
| /* | |
| * While setting the time, the RTC TIME register should not be | |
| * accessed. Setting the RTC time involves sleeping during | |
| * 100ms, so a mutex instead of a spinlock is used to protect | |
| * it | |
| */ | |
| struct mutex mutex_time; | |
| int irq; | |
| }; | |
| /* | |
| * According to the datasheet, the OS should wait 5us after every | |
| * register write to the RTC hard macro so that the required update | |
| * can occur without holding off the system bus | |
| */ | |
| static void rtc_delayed_write(u32 val, struct armada38x_rtc *rtc, int offset) | |
| { | |
| writel(val, rtc->regs + offset); | |
| udelay(5); | |
| } | |
| static int armada38x_rtc_read_time(struct device *dev, struct rtc_time *tm) | |
| { | |
| struct armada38x_rtc *rtc = dev_get_drvdata(dev); | |
| unsigned long time, time_check; | |
| mutex_lock(&rtc->mutex_time); | |
| time = readl(rtc->regs + RTC_TIME); | |
| /* | |
| * WA for failing time set attempts. As stated in HW ERRATA if | |
| * more than one second between two time reads is detected | |
| * then read once again. | |
| */ | |
| time_check = readl(rtc->regs + RTC_TIME); | |
| if ((time_check - time) > 1) | |
| time_check = readl(rtc->regs + RTC_TIME); | |
| mutex_unlock(&rtc->mutex_time); | |
| rtc_time_to_tm(time_check, tm); | |
| return 0; | |
| } | |
| static int armada38x_rtc_set_time(struct device *dev, struct rtc_time *tm) | |
| { | |
| struct armada38x_rtc *rtc = dev_get_drvdata(dev); | |
| int ret = 0; | |
| unsigned long time, flags; | |
| ret = rtc_tm_to_time(tm, &time); | |
| if (ret) | |
| goto out; | |
| /* | |
| * Setting the RTC time not always succeeds. According to the | |
| * errata we need to first write on the status register and | |
| * then wait for 100ms before writing to the time register to be | |
| * sure that the data will be taken into account. | |
| */ | |
| mutex_lock(&rtc->mutex_time); | |
| rtc_delayed_write(0, rtc, RTC_STATUS); | |
| msleep(100); | |
| rtc_delayed_write(time, rtc, RTC_TIME); | |
| mutex_unlock(&rtc->mutex_time); | |
| out: | |
| return ret; | |
| } | |
| static int armada38x_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm) | |
| { | |
| struct armada38x_rtc *rtc = dev_get_drvdata(dev); | |
| unsigned long time, flags; | |
| u32 val; | |
| spin_lock_irqsave(&rtc->lock, flags); | |
| time = readl(rtc->regs + RTC_ALARM1); | |
| val = readl(rtc->regs + RTC_IRQ1_CONF) & RTC_IRQ1_AL_EN; | |
| spin_unlock_irqrestore(&rtc->lock, flags); | |
| alrm->enabled = val ? 1 : 0; | |
| rtc_time_to_tm(time, &alrm->time); | |
| return 0; | |
| } | |
| static int armada38x_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm) | |
| { | |
| struct armada38x_rtc *rtc = dev_get_drvdata(dev); | |
| unsigned long time, flags; | |
| int ret = 0; | |
| u32 val; | |
| ret = rtc_tm_to_time(&alrm->time, &time); | |
| if (ret) | |
| goto out; | |
| spin_lock_irqsave(&rtc->lock, flags); | |
| rtc_delayed_write(time, rtc, RTC_ALARM1); | |
| if (alrm->enabled) { | |
| rtc_delayed_write(RTC_IRQ1_AL_EN, rtc, RTC_IRQ1_CONF); | |
| val = readl(rtc->regs_soc + SOC_RTC_INTERRUPT); | |
| writel(val | SOC_RTC_ALARM1_MASK, | |
| rtc->regs_soc + SOC_RTC_INTERRUPT); | |
| } | |
| spin_unlock_irqrestore(&rtc->lock, flags); | |
| out: | |
| return ret; | |
| } | |
| static int armada38x_rtc_alarm_irq_enable(struct device *dev, | |
| unsigned int enabled) | |
| { | |
| struct armada38x_rtc *rtc = dev_get_drvdata(dev); | |
| unsigned long flags; | |
| spin_lock_irqsave(&rtc->lock, flags); | |
| if (enabled) | |
| rtc_delayed_write(RTC_IRQ1_AL_EN, rtc, RTC_IRQ1_CONF); | |
| else | |
| rtc_delayed_write(0, rtc, RTC_IRQ1_CONF); | |
| spin_unlock_irqrestore(&rtc->lock, flags); | |
| return 0; | |
| } | |
| static irqreturn_t armada38x_rtc_alarm_irq(int irq, void *data) | |
| { | |
| struct armada38x_rtc *rtc = data; | |
| u32 val; | |
| int event = RTC_IRQF | RTC_AF; | |
| dev_dbg(&rtc->rtc_dev->dev, "%s:irq(%d)\n", __func__, irq); | |
| spin_lock(&rtc->lock); | |
| val = readl(rtc->regs_soc + SOC_RTC_INTERRUPT); | |
| writel(val & ~SOC_RTC_ALARM1, rtc->regs_soc + SOC_RTC_INTERRUPT); | |
| val = readl(rtc->regs + RTC_IRQ1_CONF); | |
| /* disable all the interrupts for alarm 1 */ | |
| rtc_delayed_write(0, rtc, RTC_IRQ1_CONF); | |
| /* Ack the event */ | |
| rtc_delayed_write(RTC_STATUS_ALARM1, rtc, RTC_STATUS); | |
| spin_unlock(&rtc->lock); | |
| if (val & RTC_IRQ1_FREQ_EN) { | |
| if (val & RTC_IRQ1_FREQ_1HZ) | |
| event |= RTC_UF; | |
| else | |
| event |= RTC_PF; | |
| } | |
| rtc_update_irq(rtc->rtc_dev, 1, event); | |
| return IRQ_HANDLED; | |
| } | |
| static struct rtc_class_ops armada38x_rtc_ops = { | |
| .read_time = armada38x_rtc_read_time, | |
| .set_time = armada38x_rtc_set_time, | |
| .read_alarm = armada38x_rtc_read_alarm, | |
| .set_alarm = armada38x_rtc_set_alarm, | |
| .alarm_irq_enable = armada38x_rtc_alarm_irq_enable, | |
| }; | |
| static __init int armada38x_rtc_probe(struct platform_device *pdev) | |
| { | |
| struct resource *res; | |
| struct armada38x_rtc *rtc; | |
| int ret; | |
| rtc = devm_kzalloc(&pdev->dev, sizeof(struct armada38x_rtc), | |
| GFP_KERNEL); | |
| if (!rtc) | |
| return -ENOMEM; | |
| spin_lock_init(&rtc->lock); | |
| mutex_init(&rtc->mutex_time); | |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rtc"); | |
| rtc->regs = devm_ioremap_resource(&pdev->dev, res); | |
| if (IS_ERR(rtc->regs)) | |
| return PTR_ERR(rtc->regs); | |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rtc-soc"); | |
| rtc->regs_soc = devm_ioremap_resource(&pdev->dev, res); | |
| if (IS_ERR(rtc->regs_soc)) | |
| return PTR_ERR(rtc->regs_soc); | |
| rtc->irq = platform_get_irq(pdev, 0); | |
| if (rtc->irq < 0) { | |
| dev_err(&pdev->dev, "no irq\n"); | |
| return rtc->irq; | |
| } | |
| if (devm_request_irq(&pdev->dev, rtc->irq, armada38x_rtc_alarm_irq, | |
| 0, pdev->name, rtc) < 0) { | |
| dev_warn(&pdev->dev, "Interrupt not available.\n"); | |
| rtc->irq = -1; | |
| /* | |
| * If there is no interrupt available then we can't | |
| * use the alarm | |
| */ | |
| armada38x_rtc_ops.set_alarm = NULL; | |
| armada38x_rtc_ops.alarm_irq_enable = NULL; | |
| } | |
| platform_set_drvdata(pdev, rtc); | |
| if (rtc->irq != -1) | |
| device_init_wakeup(&pdev->dev, 1); | |
| rtc->rtc_dev = devm_rtc_device_register(&pdev->dev, pdev->name, | |
| &armada38x_rtc_ops, THIS_MODULE); | |
| if (IS_ERR(rtc->rtc_dev)) { | |
| ret = PTR_ERR(rtc->rtc_dev); | |
| dev_err(&pdev->dev, "Failed to register RTC device: %d\n", ret); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| #ifdef CONFIG_PM_SLEEP | |
| static int armada38x_rtc_suspend(struct device *dev) | |
| { | |
| if (device_may_wakeup(dev)) { | |
| struct armada38x_rtc *rtc = dev_get_drvdata(dev); | |
| return enable_irq_wake(rtc->irq); | |
| } | |
| return 0; | |
| } | |
| static int armada38x_rtc_resume(struct device *dev) | |
| { | |
| if (device_may_wakeup(dev)) { | |
| struct armada38x_rtc *rtc = dev_get_drvdata(dev); | |
| return disable_irq_wake(rtc->irq); | |
| } | |
| return 0; | |
| } | |
| #endif | |
| static SIMPLE_DEV_PM_OPS(armada38x_rtc_pm_ops, | |
| armada38x_rtc_suspend, armada38x_rtc_resume); | |
| #ifdef CONFIG_OF | |
| static const struct of_device_id armada38x_rtc_of_match_table[] = { | |
| { .compatible = "marvell,armada-380-rtc", }, | |
| {} | |
| }; | |
| #endif | |
| static struct platform_driver armada38x_rtc_driver = { | |
| .driver = { | |
| .name = "armada38x-rtc", | |
| .pm = &armada38x_rtc_pm_ops, | |
| .of_match_table = of_match_ptr(armada38x_rtc_of_match_table), | |
| }, | |
| }; | |
| module_platform_driver_probe(armada38x_rtc_driver, armada38x_rtc_probe); | |
| MODULE_DESCRIPTION("Marvell Armada 38x RTC driver"); | |
| MODULE_AUTHOR("Gregory CLEMENT <gregory.clement@free-electrons.com>"); | |
| MODULE_LICENSE("GPL"); |