| /* |
| * ALSA SoC Texas Instruments TLV320DAC33 codec driver |
| * |
| * Author: Peter Ujfalusi <peter.ujfalusi@ti.com> |
| * |
| * Copyright: (C) 2009 Nokia Corporation |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA |
| * 02110-1301 USA |
| * |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| #include <linux/init.h> |
| #include <linux/delay.h> |
| #include <linux/pm.h> |
| #include <linux/i2c.h> |
| #include <linux/interrupt.h> |
| #include <linux/gpio.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/slab.h> |
| #include <sound/core.h> |
| #include <sound/pcm.h> |
| #include <sound/pcm_params.h> |
| #include <sound/soc.h> |
| #include <sound/initval.h> |
| #include <sound/tlv.h> |
| |
| #include <sound/tlv320dac33-plat.h> |
| #include "tlv320dac33.h" |
| |
| /* |
| * The internal FIFO is 24576 bytes long |
| * It can be configured to hold 16bit or 24bit samples |
| * In 16bit configuration the FIFO can hold 6144 stereo samples |
| * In 24bit configuration the FIFO can hold 4096 stereo samples |
| */ |
| #define DAC33_FIFO_SIZE_16BIT 6144 |
| #define DAC33_FIFO_SIZE_24BIT 4096 |
| #define DAC33_MODE7_MARGIN 10 /* Safety margin for FIFO in Mode7 */ |
| |
| #define BURST_BASEFREQ_HZ 49152000 |
| |
| #define SAMPLES_TO_US(rate, samples) \ |
| (1000000000 / (((rate) * 1000) / (samples))) |
| |
| #define US_TO_SAMPLES(rate, us) \ |
| ((rate) / (1000000 / ((us) < 1000000 ? (us) : 1000000))) |
| |
| #define UTHR_FROM_PERIOD_SIZE(samples, playrate, burstrate) \ |
| (((samples)*5000) / (((burstrate)*5000) / ((burstrate) - (playrate)))) |
| |
| static void dac33_calculate_times(struct snd_pcm_substream *substream, |
| struct snd_soc_component *component); |
| static int dac33_prepare_chip(struct snd_pcm_substream *substream, |
| struct snd_soc_component *component); |
| |
| enum dac33_state { |
| DAC33_IDLE = 0, |
| DAC33_PREFILL, |
| DAC33_PLAYBACK, |
| DAC33_FLUSH, |
| }; |
| |
| enum dac33_fifo_modes { |
| DAC33_FIFO_BYPASS = 0, |
| DAC33_FIFO_MODE1, |
| DAC33_FIFO_MODE7, |
| DAC33_FIFO_LAST_MODE, |
| }; |
| |
| #define DAC33_NUM_SUPPLIES 3 |
| static const char *dac33_supply_names[DAC33_NUM_SUPPLIES] = { |
| "AVDD", |
| "DVDD", |
| "IOVDD", |
| }; |
| |
| struct tlv320dac33_priv { |
| struct mutex mutex; |
| struct work_struct work; |
| struct snd_soc_component *component; |
| struct regulator_bulk_data supplies[DAC33_NUM_SUPPLIES]; |
| struct snd_pcm_substream *substream; |
| int power_gpio; |
| int chip_power; |
| int irq; |
| unsigned int refclk; |
| |
| unsigned int alarm_threshold; /* set to be half of LATENCY_TIME_MS */ |
| enum dac33_fifo_modes fifo_mode;/* FIFO mode selection */ |
| unsigned int fifo_size; /* Size of the FIFO in samples */ |
| unsigned int nsample; /* burst read amount from host */ |
| int mode1_latency; /* latency caused by the i2c writes in |
| * us */ |
| u8 burst_bclkdiv; /* BCLK divider value in burst mode */ |
| u8 *reg_cache; |
| unsigned int burst_rate; /* Interface speed in Burst modes */ |
| |
| int keep_bclk; /* Keep the BCLK continuously running |
| * in FIFO modes */ |
| spinlock_t lock; |
| unsigned long long t_stamp1; /* Time stamp for FIFO modes to */ |
| unsigned long long t_stamp2; /* calculate the FIFO caused delay */ |
| |
| unsigned int mode1_us_burst; /* Time to burst read n number of |
| * samples */ |
| unsigned int mode7_us_to_lthr; /* Time to reach lthr from uthr */ |
| |
| unsigned int uthr; |
| |
| enum dac33_state state; |
| struct i2c_client *i2c; |
| }; |
| |
| static const u8 dac33_reg[DAC33_CACHEREGNUM] = { |
| 0x00, 0x00, 0x00, 0x00, /* 0x00 - 0x03 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x04 - 0x07 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x08 - 0x0b */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x0c - 0x0f */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x10 - 0x13 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x14 - 0x17 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x18 - 0x1b */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x1c - 0x1f */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x20 - 0x23 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x24 - 0x27 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x28 - 0x2b */ |
| 0x00, 0x00, 0x00, 0x80, /* 0x2c - 0x2f */ |
| 0x80, 0x00, 0x00, 0x00, /* 0x30 - 0x33 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x34 - 0x37 */ |
| 0x00, 0x00, /* 0x38 - 0x39 */ |
| /* Registers 0x3a - 0x3f are reserved */ |
| 0x00, 0x00, /* 0x3a - 0x3b */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x3c - 0x3f */ |
| |
| 0x00, 0x00, 0x00, 0x00, /* 0x40 - 0x43 */ |
| 0x00, 0x80, /* 0x44 - 0x45 */ |
| /* Registers 0x46 - 0x47 are reserved */ |
| 0x80, 0x80, /* 0x46 - 0x47 */ |
| |
| 0x80, 0x00, 0x00, /* 0x48 - 0x4a */ |
| /* Registers 0x4b - 0x7c are reserved */ |
| 0x00, /* 0x4b */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x4c - 0x4f */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x50 - 0x53 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x54 - 0x57 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x58 - 0x5b */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x5c - 0x5f */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x60 - 0x63 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x64 - 0x67 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x68 - 0x6b */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x6c - 0x6f */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x70 - 0x73 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x74 - 0x77 */ |
| 0x00, 0x00, 0x00, 0x00, /* 0x78 - 0x7b */ |
| 0x00, /* 0x7c */ |
| |
| 0xda, 0x33, 0x03, /* 0x7d - 0x7f */ |
| }; |
| |
| /* Register read and write */ |
| static inline unsigned int dac33_read_reg_cache(struct snd_soc_component *component, |
| unsigned reg) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| u8 *cache = dac33->reg_cache; |
| if (reg >= DAC33_CACHEREGNUM) |
| return 0; |
| |
| return cache[reg]; |
| } |
| |
| static inline void dac33_write_reg_cache(struct snd_soc_component *component, |
| u8 reg, u8 value) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| u8 *cache = dac33->reg_cache; |
| if (reg >= DAC33_CACHEREGNUM) |
| return; |
| |
| cache[reg] = value; |
| } |
| |
| static int dac33_read(struct snd_soc_component *component, unsigned int reg, |
| u8 *value) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| int val, ret = 0; |
| |
| *value = reg & 0xff; |
| |
| /* If powered off, return the cached value */ |
| if (dac33->chip_power) { |
| val = i2c_smbus_read_byte_data(dac33->i2c, value[0]); |
| if (val < 0) { |
| dev_err(component->dev, "Read failed (%d)\n", val); |
| value[0] = dac33_read_reg_cache(component, reg); |
| ret = val; |
| } else { |
| value[0] = val; |
| dac33_write_reg_cache(component, reg, val); |
| } |
| } else { |
| value[0] = dac33_read_reg_cache(component, reg); |
| } |
| |
| return ret; |
| } |
| |
| static int dac33_write(struct snd_soc_component *component, unsigned int reg, |
| unsigned int value) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| u8 data[2]; |
| int ret = 0; |
| |
| /* |
| * data is |
| * D15..D8 dac33 register offset |
| * D7...D0 register data |
| */ |
| data[0] = reg & 0xff; |
| data[1] = value & 0xff; |
| |
| dac33_write_reg_cache(component, data[0], data[1]); |
| if (dac33->chip_power) { |
| ret = i2c_master_send(dac33->i2c, data, 2); |
| if (ret != 2) |
| dev_err(component->dev, "Write failed (%d)\n", ret); |
| else |
| ret = 0; |
| } |
| |
| return ret; |
| } |
| |
| static int dac33_write_locked(struct snd_soc_component *component, unsigned int reg, |
| unsigned int value) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| int ret; |
| |
| mutex_lock(&dac33->mutex); |
| ret = dac33_write(component, reg, value); |
| mutex_unlock(&dac33->mutex); |
| |
| return ret; |
| } |
| |
| #define DAC33_I2C_ADDR_AUTOINC 0x80 |
| static int dac33_write16(struct snd_soc_component *component, unsigned int reg, |
| unsigned int value) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| u8 data[3]; |
| int ret = 0; |
| |
| /* |
| * data is |
| * D23..D16 dac33 register offset |
| * D15..D8 register data MSB |
| * D7...D0 register data LSB |
| */ |
| data[0] = reg & 0xff; |
| data[1] = (value >> 8) & 0xff; |
| data[2] = value & 0xff; |
| |
| dac33_write_reg_cache(component, data[0], data[1]); |
| dac33_write_reg_cache(component, data[0] + 1, data[2]); |
| |
| if (dac33->chip_power) { |
| /* We need to set autoincrement mode for 16 bit writes */ |
| data[0] |= DAC33_I2C_ADDR_AUTOINC; |
| ret = i2c_master_send(dac33->i2c, data, 3); |
| if (ret != 3) |
| dev_err(component->dev, "Write failed (%d)\n", ret); |
| else |
| ret = 0; |
| } |
| |
| return ret; |
| } |
| |
| static void dac33_init_chip(struct snd_soc_component *component) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| |
| if (unlikely(!dac33->chip_power)) |
| return; |
| |
| /* A : DAC sample rate Fsref/1.5 */ |
| dac33_write(component, DAC33_DAC_CTRL_A, DAC33_DACRATE(0)); |
| /* B : DAC src=normal, not muted */ |
| dac33_write(component, DAC33_DAC_CTRL_B, DAC33_DACSRCR_RIGHT | |
| DAC33_DACSRCL_LEFT); |
| /* C : (defaults) */ |
| dac33_write(component, DAC33_DAC_CTRL_C, 0x00); |
| |
| /* 73 : volume soft stepping control, |
| clock source = internal osc (?) */ |
| dac33_write(component, DAC33_ANA_VOL_SOFT_STEP_CTRL, DAC33_VOLCLKEN); |
| |
| /* Restore only selected registers (gains mostly) */ |
| dac33_write(component, DAC33_LDAC_DIG_VOL_CTRL, |
| dac33_read_reg_cache(component, DAC33_LDAC_DIG_VOL_CTRL)); |
| dac33_write(component, DAC33_RDAC_DIG_VOL_CTRL, |
| dac33_read_reg_cache(component, DAC33_RDAC_DIG_VOL_CTRL)); |
| |
| dac33_write(component, DAC33_LINEL_TO_LLO_VOL, |
| dac33_read_reg_cache(component, DAC33_LINEL_TO_LLO_VOL)); |
| dac33_write(component, DAC33_LINER_TO_RLO_VOL, |
| dac33_read_reg_cache(component, DAC33_LINER_TO_RLO_VOL)); |
| |
| dac33_write(component, DAC33_OUT_AMP_CTRL, |
| dac33_read_reg_cache(component, DAC33_OUT_AMP_CTRL)); |
| |
| dac33_write(component, DAC33_LDAC_PWR_CTRL, |
| dac33_read_reg_cache(component, DAC33_LDAC_PWR_CTRL)); |
| dac33_write(component, DAC33_RDAC_PWR_CTRL, |
| dac33_read_reg_cache(component, DAC33_RDAC_PWR_CTRL)); |
| } |
| |
| static inline int dac33_read_id(struct snd_soc_component *component) |
| { |
| int i, ret = 0; |
| u8 reg; |
| |
| for (i = 0; i < 3; i++) { |
| ret = dac33_read(component, DAC33_DEVICE_ID_MSB + i, ®); |
| if (ret < 0) |
| break; |
| } |
| |
| return ret; |
| } |
| |
| static inline void dac33_soft_power(struct snd_soc_component *component, int power) |
| { |
| u8 reg; |
| |
| reg = dac33_read_reg_cache(component, DAC33_PWR_CTRL); |
| if (power) |
| reg |= DAC33_PDNALLB; |
| else |
| reg &= ~(DAC33_PDNALLB | DAC33_OSCPDNB | |
| DAC33_DACRPDNB | DAC33_DACLPDNB); |
| dac33_write(component, DAC33_PWR_CTRL, reg); |
| } |
| |
| static inline void dac33_disable_digital(struct snd_soc_component *component) |
| { |
| u8 reg; |
| |
| /* Stop the DAI clock */ |
| reg = dac33_read_reg_cache(component, DAC33_SER_AUDIOIF_CTRL_B); |
| reg &= ~DAC33_BCLKON; |
| dac33_write(component, DAC33_SER_AUDIOIF_CTRL_B, reg); |
| |
| /* Power down the Oscillator, and DACs */ |
| reg = dac33_read_reg_cache(component, DAC33_PWR_CTRL); |
| reg &= ~(DAC33_OSCPDNB | DAC33_DACRPDNB | DAC33_DACLPDNB); |
| dac33_write(component, DAC33_PWR_CTRL, reg); |
| } |
| |
| static int dac33_hard_power(struct snd_soc_component *component, int power) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| int ret = 0; |
| |
| mutex_lock(&dac33->mutex); |
| |
| /* Safety check */ |
| if (unlikely(power == dac33->chip_power)) { |
| dev_dbg(component->dev, "Trying to set the same power state: %s\n", |
| power ? "ON" : "OFF"); |
| goto exit; |
| } |
| |
| if (power) { |
| ret = regulator_bulk_enable(ARRAY_SIZE(dac33->supplies), |
| dac33->supplies); |
| if (ret != 0) { |
| dev_err(component->dev, |
| "Failed to enable supplies: %d\n", ret); |
| goto exit; |
| } |
| |
| if (dac33->power_gpio >= 0) |
| gpio_set_value(dac33->power_gpio, 1); |
| |
| dac33->chip_power = 1; |
| } else { |
| dac33_soft_power(component, 0); |
| if (dac33->power_gpio >= 0) |
| gpio_set_value(dac33->power_gpio, 0); |
| |
| ret = regulator_bulk_disable(ARRAY_SIZE(dac33->supplies), |
| dac33->supplies); |
| if (ret != 0) { |
| dev_err(component->dev, |
| "Failed to disable supplies: %d\n", ret); |
| goto exit; |
| } |
| |
| dac33->chip_power = 0; |
| } |
| |
| exit: |
| mutex_unlock(&dac33->mutex); |
| return ret; |
| } |
| |
| static int dac33_playback_event(struct snd_soc_dapm_widget *w, |
| struct snd_kcontrol *kcontrol, int event) |
| { |
| struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm); |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| |
| switch (event) { |
| case SND_SOC_DAPM_PRE_PMU: |
| if (likely(dac33->substream)) { |
| dac33_calculate_times(dac33->substream, component); |
| dac33_prepare_chip(dac33->substream, component); |
| } |
| break; |
| case SND_SOC_DAPM_POST_PMD: |
| dac33_disable_digital(component); |
| break; |
| } |
| return 0; |
| } |
| |
| static int dac33_get_fifo_mode(struct snd_kcontrol *kcontrol, |
| struct snd_ctl_elem_value *ucontrol) |
| { |
| struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| |
| ucontrol->value.enumerated.item[0] = dac33->fifo_mode; |
| |
| return 0; |
| } |
| |
| static int dac33_set_fifo_mode(struct snd_kcontrol *kcontrol, |
| struct snd_ctl_elem_value *ucontrol) |
| { |
| struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| int ret = 0; |
| |
| if (dac33->fifo_mode == ucontrol->value.enumerated.item[0]) |
| return 0; |
| /* Do not allow changes while stream is running*/ |
| if (snd_soc_component_is_active(component)) |
| return -EPERM; |
| |
| if (ucontrol->value.enumerated.item[0] >= DAC33_FIFO_LAST_MODE) |
| ret = -EINVAL; |
| else |
| dac33->fifo_mode = ucontrol->value.enumerated.item[0]; |
| |
| return ret; |
| } |
| |
| /* Codec operation modes */ |
| static const char *dac33_fifo_mode_texts[] = { |
| "Bypass", "Mode 1", "Mode 7" |
| }; |
| |
| static SOC_ENUM_SINGLE_EXT_DECL(dac33_fifo_mode_enum, dac33_fifo_mode_texts); |
| |
| /* L/R Line Output Gain */ |
| static const char *lr_lineout_gain_texts[] = { |
| "Line -12dB DAC 0dB", "Line -6dB DAC 6dB", |
| "Line 0dB DAC 12dB", "Line 6dB DAC 18dB", |
| }; |
| |
| static SOC_ENUM_SINGLE_DECL(l_lineout_gain_enum, |
| DAC33_LDAC_PWR_CTRL, 0, |
| lr_lineout_gain_texts); |
| |
| static SOC_ENUM_SINGLE_DECL(r_lineout_gain_enum, |
| DAC33_RDAC_PWR_CTRL, 0, |
| lr_lineout_gain_texts); |
| |
| /* |
| * DACL/R digital volume control: |
| * from 0 dB to -63.5 in 0.5 dB steps |
| * Need to be inverted later on: |
| * 0x00 == 0 dB |
| * 0x7f == -63.5 dB |
| */ |
| static DECLARE_TLV_DB_SCALE(dac_digivol_tlv, -6350, 50, 0); |
| |
| static const struct snd_kcontrol_new dac33_snd_controls[] = { |
| SOC_DOUBLE_R_TLV("DAC Digital Playback Volume", |
| DAC33_LDAC_DIG_VOL_CTRL, DAC33_RDAC_DIG_VOL_CTRL, |
| 0, 0x7f, 1, dac_digivol_tlv), |
| SOC_DOUBLE_R("DAC Digital Playback Switch", |
| DAC33_LDAC_DIG_VOL_CTRL, DAC33_RDAC_DIG_VOL_CTRL, 7, 1, 1), |
| SOC_DOUBLE_R("Line to Line Out Volume", |
| DAC33_LINEL_TO_LLO_VOL, DAC33_LINER_TO_RLO_VOL, 0, 127, 1), |
| SOC_ENUM("Left Line Output Gain", l_lineout_gain_enum), |
| SOC_ENUM("Right Line Output Gain", r_lineout_gain_enum), |
| }; |
| |
| static const struct snd_kcontrol_new dac33_mode_snd_controls[] = { |
| SOC_ENUM_EXT("FIFO Mode", dac33_fifo_mode_enum, |
| dac33_get_fifo_mode, dac33_set_fifo_mode), |
| }; |
| |
| /* Analog bypass */ |
| static const struct snd_kcontrol_new dac33_dapm_abypassl_control = |
| SOC_DAPM_SINGLE("Switch", DAC33_LINEL_TO_LLO_VOL, 7, 1, 1); |
| |
| static const struct snd_kcontrol_new dac33_dapm_abypassr_control = |
| SOC_DAPM_SINGLE("Switch", DAC33_LINER_TO_RLO_VOL, 7, 1, 1); |
| |
| /* LOP L/R invert selection */ |
| static const char *dac33_lr_lom_texts[] = {"DAC", "LOP"}; |
| |
| static SOC_ENUM_SINGLE_DECL(dac33_left_lom_enum, |
| DAC33_OUT_AMP_CTRL, 3, |
| dac33_lr_lom_texts); |
| |
| static const struct snd_kcontrol_new dac33_dapm_left_lom_control = |
| SOC_DAPM_ENUM("Route", dac33_left_lom_enum); |
| |
| static SOC_ENUM_SINGLE_DECL(dac33_right_lom_enum, |
| DAC33_OUT_AMP_CTRL, 2, |
| dac33_lr_lom_texts); |
| |
| static const struct snd_kcontrol_new dac33_dapm_right_lom_control = |
| SOC_DAPM_ENUM("Route", dac33_right_lom_enum); |
| |
| static const struct snd_soc_dapm_widget dac33_dapm_widgets[] = { |
| SND_SOC_DAPM_OUTPUT("LEFT_LO"), |
| SND_SOC_DAPM_OUTPUT("RIGHT_LO"), |
| |
| SND_SOC_DAPM_INPUT("LINEL"), |
| SND_SOC_DAPM_INPUT("LINER"), |
| |
| SND_SOC_DAPM_DAC("DACL", "Left Playback", SND_SOC_NOPM, 0, 0), |
| SND_SOC_DAPM_DAC("DACR", "Right Playback", SND_SOC_NOPM, 0, 0), |
| |
| /* Analog bypass */ |
| SND_SOC_DAPM_SWITCH("Analog Left Bypass", SND_SOC_NOPM, 0, 0, |
| &dac33_dapm_abypassl_control), |
| SND_SOC_DAPM_SWITCH("Analog Right Bypass", SND_SOC_NOPM, 0, 0, |
| &dac33_dapm_abypassr_control), |
| |
| SND_SOC_DAPM_MUX("Left LOM Inverted From", SND_SOC_NOPM, 0, 0, |
| &dac33_dapm_left_lom_control), |
| SND_SOC_DAPM_MUX("Right LOM Inverted From", SND_SOC_NOPM, 0, 0, |
| &dac33_dapm_right_lom_control), |
| /* |
| * For DAPM path, when only the anlog bypass path is enabled, and the |
| * LOP inverted from the corresponding DAC side. |
| * This is needed, so we can attach the DAC power supply in this case. |
| */ |
| SND_SOC_DAPM_PGA("Left Bypass PGA", SND_SOC_NOPM, 0, 0, NULL, 0), |
| SND_SOC_DAPM_PGA("Right Bypass PGA", SND_SOC_NOPM, 0, 0, NULL, 0), |
| |
| SND_SOC_DAPM_REG(snd_soc_dapm_mixer, "Output Left Amplifier", |
| DAC33_OUT_AMP_PWR_CTRL, 6, 3, 3, 0), |
| SND_SOC_DAPM_REG(snd_soc_dapm_mixer, "Output Right Amplifier", |
| DAC33_OUT_AMP_PWR_CTRL, 4, 3, 3, 0), |
| |
| SND_SOC_DAPM_SUPPLY("Left DAC Power", |
| DAC33_LDAC_PWR_CTRL, 2, 0, NULL, 0), |
| SND_SOC_DAPM_SUPPLY("Right DAC Power", |
| DAC33_RDAC_PWR_CTRL, 2, 0, NULL, 0), |
| |
| SND_SOC_DAPM_SUPPLY("Codec Power", |
| DAC33_PWR_CTRL, 4, 0, NULL, 0), |
| |
| SND_SOC_DAPM_PRE("Pre Playback", dac33_playback_event), |
| SND_SOC_DAPM_POST("Post Playback", dac33_playback_event), |
| }; |
| |
| static const struct snd_soc_dapm_route audio_map[] = { |
| /* Analog bypass */ |
| {"Analog Left Bypass", "Switch", "LINEL"}, |
| {"Analog Right Bypass", "Switch", "LINER"}, |
| |
| {"Output Left Amplifier", NULL, "DACL"}, |
| {"Output Right Amplifier", NULL, "DACR"}, |
| |
| {"Left Bypass PGA", NULL, "Analog Left Bypass"}, |
| {"Right Bypass PGA", NULL, "Analog Right Bypass"}, |
| |
| {"Left LOM Inverted From", "DAC", "Left Bypass PGA"}, |
| {"Right LOM Inverted From", "DAC", "Right Bypass PGA"}, |
| {"Left LOM Inverted From", "LOP", "Analog Left Bypass"}, |
| {"Right LOM Inverted From", "LOP", "Analog Right Bypass"}, |
| |
| {"Output Left Amplifier", NULL, "Left LOM Inverted From"}, |
| {"Output Right Amplifier", NULL, "Right LOM Inverted From"}, |
| |
| {"DACL", NULL, "Left DAC Power"}, |
| {"DACR", NULL, "Right DAC Power"}, |
| |
| {"Left Bypass PGA", NULL, "Left DAC Power"}, |
| {"Right Bypass PGA", NULL, "Right DAC Power"}, |
| |
| /* output */ |
| {"LEFT_LO", NULL, "Output Left Amplifier"}, |
| {"RIGHT_LO", NULL, "Output Right Amplifier"}, |
| |
| {"LEFT_LO", NULL, "Codec Power"}, |
| {"RIGHT_LO", NULL, "Codec Power"}, |
| }; |
| |
| static int dac33_set_bias_level(struct snd_soc_component *component, |
| enum snd_soc_bias_level level) |
| { |
| int ret; |
| |
| switch (level) { |
| case SND_SOC_BIAS_ON: |
| break; |
| case SND_SOC_BIAS_PREPARE: |
| break; |
| case SND_SOC_BIAS_STANDBY: |
| if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_OFF) { |
| /* Coming from OFF, switch on the component */ |
| ret = dac33_hard_power(component, 1); |
| if (ret != 0) |
| return ret; |
| |
| dac33_init_chip(component); |
| } |
| break; |
| case SND_SOC_BIAS_OFF: |
| /* Do not power off, when the component is already off */ |
| if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_OFF) |
| return 0; |
| ret = dac33_hard_power(component, 0); |
| if (ret != 0) |
| return ret; |
| break; |
| } |
| |
| return 0; |
| } |
| |
| static inline void dac33_prefill_handler(struct tlv320dac33_priv *dac33) |
| { |
| struct snd_soc_component *component = dac33->component; |
| unsigned int delay; |
| unsigned long flags; |
| |
| switch (dac33->fifo_mode) { |
| case DAC33_FIFO_MODE1: |
| dac33_write16(component, DAC33_NSAMPLE_MSB, |
| DAC33_THRREG(dac33->nsample)); |
| |
| /* Take the timestamps */ |
| spin_lock_irqsave(&dac33->lock, flags); |
| dac33->t_stamp2 = ktime_to_us(ktime_get()); |
| dac33->t_stamp1 = dac33->t_stamp2; |
| spin_unlock_irqrestore(&dac33->lock, flags); |
| |
| dac33_write16(component, DAC33_PREFILL_MSB, |
| DAC33_THRREG(dac33->alarm_threshold)); |
| /* Enable Alarm Threshold IRQ with a delay */ |
| delay = SAMPLES_TO_US(dac33->burst_rate, |
| dac33->alarm_threshold) + 1000; |
| usleep_range(delay, delay + 500); |
| dac33_write(component, DAC33_FIFO_IRQ_MASK, DAC33_MAT); |
| break; |
| case DAC33_FIFO_MODE7: |
| /* Take the timestamp */ |
| spin_lock_irqsave(&dac33->lock, flags); |
| dac33->t_stamp1 = ktime_to_us(ktime_get()); |
| /* Move back the timestamp with drain time */ |
| dac33->t_stamp1 -= dac33->mode7_us_to_lthr; |
| spin_unlock_irqrestore(&dac33->lock, flags); |
| |
| dac33_write16(component, DAC33_PREFILL_MSB, |
| DAC33_THRREG(DAC33_MODE7_MARGIN)); |
| |
| /* Enable Upper Threshold IRQ */ |
| dac33_write(component, DAC33_FIFO_IRQ_MASK, DAC33_MUT); |
| break; |
| default: |
| dev_warn(component->dev, "Unhandled FIFO mode: %d\n", |
| dac33->fifo_mode); |
| break; |
| } |
| } |
| |
| static inline void dac33_playback_handler(struct tlv320dac33_priv *dac33) |
| { |
| struct snd_soc_component *component = dac33->component; |
| unsigned long flags; |
| |
| switch (dac33->fifo_mode) { |
| case DAC33_FIFO_MODE1: |
| /* Take the timestamp */ |
| spin_lock_irqsave(&dac33->lock, flags); |
| dac33->t_stamp2 = ktime_to_us(ktime_get()); |
| spin_unlock_irqrestore(&dac33->lock, flags); |
| |
| dac33_write16(component, DAC33_NSAMPLE_MSB, |
| DAC33_THRREG(dac33->nsample)); |
| break; |
| case DAC33_FIFO_MODE7: |
| /* At the moment we are not using interrupts in mode7 */ |
| break; |
| default: |
| dev_warn(component->dev, "Unhandled FIFO mode: %d\n", |
| dac33->fifo_mode); |
| break; |
| } |
| } |
| |
| static void dac33_work(struct work_struct *work) |
| { |
| struct snd_soc_component *component; |
| struct tlv320dac33_priv *dac33; |
| u8 reg; |
| |
| dac33 = container_of(work, struct tlv320dac33_priv, work); |
| component = dac33->component; |
| |
| mutex_lock(&dac33->mutex); |
| switch (dac33->state) { |
| case DAC33_PREFILL: |
| dac33->state = DAC33_PLAYBACK; |
| dac33_prefill_handler(dac33); |
| break; |
| case DAC33_PLAYBACK: |
| dac33_playback_handler(dac33); |
| break; |
| case DAC33_IDLE: |
| break; |
| case DAC33_FLUSH: |
| dac33->state = DAC33_IDLE; |
| /* Mask all interrupts from dac33 */ |
| dac33_write(component, DAC33_FIFO_IRQ_MASK, 0); |
| |
| /* flush fifo */ |
| reg = dac33_read_reg_cache(component, DAC33_FIFO_CTRL_A); |
| reg |= DAC33_FIFOFLUSH; |
| dac33_write(component, DAC33_FIFO_CTRL_A, reg); |
| break; |
| } |
| mutex_unlock(&dac33->mutex); |
| } |
| |
| static irqreturn_t dac33_interrupt_handler(int irq, void *dev) |
| { |
| struct snd_soc_component *component = dev; |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&dac33->lock, flags); |
| dac33->t_stamp1 = ktime_to_us(ktime_get()); |
| spin_unlock_irqrestore(&dac33->lock, flags); |
| |
| /* Do not schedule the workqueue in Mode7 */ |
| if (dac33->fifo_mode != DAC33_FIFO_MODE7) |
| schedule_work(&dac33->work); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void dac33_oscwait(struct snd_soc_component *component) |
| { |
| int timeout = 60; |
| u8 reg; |
| |
| do { |
| usleep_range(1000, 2000); |
| dac33_read(component, DAC33_INT_OSC_STATUS, ®); |
| } while (((reg & 0x03) != DAC33_OSCSTATUS_NORMAL) && timeout--); |
| if ((reg & 0x03) != DAC33_OSCSTATUS_NORMAL) |
| dev_err(component->dev, |
| "internal oscillator calibration failed\n"); |
| } |
| |
| static int dac33_startup(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *dai) |
| { |
| struct snd_soc_component *component = dai->component; |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| |
| /* Stream started, save the substream pointer */ |
| dac33->substream = substream; |
| |
| return 0; |
| } |
| |
| static void dac33_shutdown(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *dai) |
| { |
| struct snd_soc_component *component = dai->component; |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| |
| dac33->substream = NULL; |
| } |
| |
| #define CALC_BURST_RATE(bclkdiv, bclk_per_sample) \ |
| (BURST_BASEFREQ_HZ / bclkdiv / bclk_per_sample) |
| static int dac33_hw_params(struct snd_pcm_substream *substream, |
| struct snd_pcm_hw_params *params, |
| struct snd_soc_dai *dai) |
| { |
| struct snd_soc_component *component = dai->component; |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| |
| /* Check parameters for validity */ |
| switch (params_rate(params)) { |
| case 44100: |
| case 48000: |
| break; |
| default: |
| dev_err(component->dev, "unsupported rate %d\n", |
| params_rate(params)); |
| return -EINVAL; |
| } |
| |
| switch (params_width(params)) { |
| case 16: |
| dac33->fifo_size = DAC33_FIFO_SIZE_16BIT; |
| dac33->burst_rate = CALC_BURST_RATE(dac33->burst_bclkdiv, 32); |
| break; |
| case 32: |
| dac33->fifo_size = DAC33_FIFO_SIZE_24BIT; |
| dac33->burst_rate = CALC_BURST_RATE(dac33->burst_bclkdiv, 64); |
| break; |
| default: |
| dev_err(component->dev, "unsupported width %d\n", |
| params_width(params)); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| #define CALC_OSCSET(rate, refclk) ( \ |
| ((((rate * 10000) / refclk) * 4096) + 7000) / 10000) |
| #define CALC_RATIOSET(rate, refclk) ( \ |
| ((((refclk * 100000) / rate) * 16384) + 50000) / 100000) |
| |
| /* |
| * tlv320dac33 is strict on the sequence of the register writes, if the register |
| * writes happens in different order, than dac33 might end up in unknown state. |
| * Use the known, working sequence of register writes to initialize the dac33. |
| */ |
| static int dac33_prepare_chip(struct snd_pcm_substream *substream, |
| struct snd_soc_component *component) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| unsigned int oscset, ratioset, pwr_ctrl, reg_tmp; |
| u8 aictrl_a, aictrl_b, fifoctrl_a; |
| |
| switch (substream->runtime->rate) { |
| case 44100: |
| case 48000: |
| oscset = CALC_OSCSET(substream->runtime->rate, dac33->refclk); |
| ratioset = CALC_RATIOSET(substream->runtime->rate, |
| dac33->refclk); |
| break; |
| default: |
| dev_err(component->dev, "unsupported rate %d\n", |
| substream->runtime->rate); |
| return -EINVAL; |
| } |
| |
| |
| aictrl_a = dac33_read_reg_cache(component, DAC33_SER_AUDIOIF_CTRL_A); |
| aictrl_a &= ~(DAC33_NCYCL_MASK | DAC33_WLEN_MASK); |
| /* Read FIFO control A, and clear FIFO flush bit */ |
| fifoctrl_a = dac33_read_reg_cache(component, DAC33_FIFO_CTRL_A); |
| fifoctrl_a &= ~DAC33_FIFOFLUSH; |
| |
| fifoctrl_a &= ~DAC33_WIDTH; |
| switch (substream->runtime->format) { |
| case SNDRV_PCM_FORMAT_S16_LE: |
| aictrl_a |= (DAC33_NCYCL_16 | DAC33_WLEN_16); |
| fifoctrl_a |= DAC33_WIDTH; |
| break; |
| case SNDRV_PCM_FORMAT_S32_LE: |
| aictrl_a |= (DAC33_NCYCL_32 | DAC33_WLEN_24); |
| break; |
| default: |
| dev_err(component->dev, "unsupported format %d\n", |
| substream->runtime->format); |
| return -EINVAL; |
| } |
| |
| mutex_lock(&dac33->mutex); |
| |
| if (!dac33->chip_power) { |
| /* |
| * Chip is not powered yet. |
| * Do the init in the dac33_set_bias_level later. |
| */ |
| mutex_unlock(&dac33->mutex); |
| return 0; |
| } |
| |
| dac33_soft_power(component, 0); |
| dac33_soft_power(component, 1); |
| |
| reg_tmp = dac33_read_reg_cache(component, DAC33_INT_OSC_CTRL); |
| dac33_write(component, DAC33_INT_OSC_CTRL, reg_tmp); |
| |
| /* Write registers 0x08 and 0x09 (MSB, LSB) */ |
| dac33_write16(component, DAC33_INT_OSC_FREQ_RAT_A, oscset); |
| |
| /* OSC calibration time */ |
| dac33_write(component, DAC33_CALIB_TIME, 96); |
| |
| /* adjustment treshold & step */ |
| dac33_write(component, DAC33_INT_OSC_CTRL_B, DAC33_ADJTHRSHLD(2) | |
| DAC33_ADJSTEP(1)); |
| |
| /* div=4 / gain=1 / div */ |
| dac33_write(component, DAC33_INT_OSC_CTRL_C, DAC33_REFDIV(4)); |
| |
| pwr_ctrl = dac33_read_reg_cache(component, DAC33_PWR_CTRL); |
| pwr_ctrl |= DAC33_OSCPDNB | DAC33_DACRPDNB | DAC33_DACLPDNB; |
| dac33_write(component, DAC33_PWR_CTRL, pwr_ctrl); |
| |
| dac33_oscwait(component); |
| |
| if (dac33->fifo_mode) { |
| /* Generic for all FIFO modes */ |
| /* 50-51 : ASRC Control registers */ |
| dac33_write(component, DAC33_ASRC_CTRL_A, DAC33_SRCLKDIV(1)); |
| dac33_write(component, DAC33_ASRC_CTRL_B, 1); /* ??? */ |
| |
| /* Write registers 0x34 and 0x35 (MSB, LSB) */ |
| dac33_write16(component, DAC33_SRC_REF_CLK_RATIO_A, ratioset); |
| |
| /* Set interrupts to high active */ |
| dac33_write(component, DAC33_INTP_CTRL_A, DAC33_INTPM_AHIGH); |
| } else { |
| /* FIFO bypass mode */ |
| /* 50-51 : ASRC Control registers */ |
| dac33_write(component, DAC33_ASRC_CTRL_A, DAC33_SRCBYP); |
| dac33_write(component, DAC33_ASRC_CTRL_B, 0); /* ??? */ |
| } |
| |
| /* Interrupt behaviour configuration */ |
| switch (dac33->fifo_mode) { |
| case DAC33_FIFO_MODE1: |
| dac33_write(component, DAC33_FIFO_IRQ_MODE_B, |
| DAC33_ATM(DAC33_FIFO_IRQ_MODE_LEVEL)); |
| break; |
| case DAC33_FIFO_MODE7: |
| dac33_write(component, DAC33_FIFO_IRQ_MODE_A, |
| DAC33_UTM(DAC33_FIFO_IRQ_MODE_LEVEL)); |
| break; |
| default: |
| /* in FIFO bypass mode, the interrupts are not used */ |
| break; |
| } |
| |
| aictrl_b = dac33_read_reg_cache(component, DAC33_SER_AUDIOIF_CTRL_B); |
| |
| switch (dac33->fifo_mode) { |
| case DAC33_FIFO_MODE1: |
| /* |
| * For mode1: |
| * Disable the FIFO bypass (Enable the use of FIFO) |
| * Select nSample mode |
| * BCLK is only running when data is needed by DAC33 |
| */ |
| fifoctrl_a &= ~DAC33_FBYPAS; |
| fifoctrl_a &= ~DAC33_FAUTO; |
| if (dac33->keep_bclk) |
| aictrl_b |= DAC33_BCLKON; |
| else |
| aictrl_b &= ~DAC33_BCLKON; |
| break; |
| case DAC33_FIFO_MODE7: |
| /* |
| * For mode1: |
| * Disable the FIFO bypass (Enable the use of FIFO) |
| * Select Threshold mode |
| * BCLK is only running when data is needed by DAC33 |
| */ |
| fifoctrl_a &= ~DAC33_FBYPAS; |
| fifoctrl_a |= DAC33_FAUTO; |
| if (dac33->keep_bclk) |
| aictrl_b |= DAC33_BCLKON; |
| else |
| aictrl_b &= ~DAC33_BCLKON; |
| break; |
| default: |
| /* |
| * For FIFO bypass mode: |
| * Enable the FIFO bypass (Disable the FIFO use) |
| * Set the BCLK as continuous |
| */ |
| fifoctrl_a |= DAC33_FBYPAS; |
| aictrl_b |= DAC33_BCLKON; |
| break; |
| } |
| |
| dac33_write(component, DAC33_FIFO_CTRL_A, fifoctrl_a); |
| dac33_write(component, DAC33_SER_AUDIOIF_CTRL_A, aictrl_a); |
| dac33_write(component, DAC33_SER_AUDIOIF_CTRL_B, aictrl_b); |
| |
| /* |
| * BCLK divide ratio |
| * 0: 1.5 |
| * 1: 1 |
| * 2: 2 |
| * ... |
| * 254: 254 |
| * 255: 255 |
| */ |
| if (dac33->fifo_mode) |
| dac33_write(component, DAC33_SER_AUDIOIF_CTRL_C, |
| dac33->burst_bclkdiv); |
| else |
| if (substream->runtime->format == SNDRV_PCM_FORMAT_S16_LE) |
| dac33_write(component, DAC33_SER_AUDIOIF_CTRL_C, 32); |
| else |
| dac33_write(component, DAC33_SER_AUDIOIF_CTRL_C, 16); |
| |
| switch (dac33->fifo_mode) { |
| case DAC33_FIFO_MODE1: |
| dac33_write16(component, DAC33_ATHR_MSB, |
| DAC33_THRREG(dac33->alarm_threshold)); |
| break; |
| case DAC33_FIFO_MODE7: |
| /* |
| * Configure the threshold levels, and leave 10 sample space |
| * at the bottom, and also at the top of the FIFO |
| */ |
| dac33_write16(component, DAC33_UTHR_MSB, DAC33_THRREG(dac33->uthr)); |
| dac33_write16(component, DAC33_LTHR_MSB, |
| DAC33_THRREG(DAC33_MODE7_MARGIN)); |
| break; |
| default: |
| break; |
| } |
| |
| mutex_unlock(&dac33->mutex); |
| |
| return 0; |
| } |
| |
| static void dac33_calculate_times(struct snd_pcm_substream *substream, |
| struct snd_soc_component *component) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| unsigned int period_size = substream->runtime->period_size; |
| unsigned int rate = substream->runtime->rate; |
| unsigned int nsample_limit; |
| |
| /* In bypass mode we don't need to calculate */ |
| if (!dac33->fifo_mode) |
| return; |
| |
| switch (dac33->fifo_mode) { |
| case DAC33_FIFO_MODE1: |
| /* Number of samples under i2c latency */ |
| dac33->alarm_threshold = US_TO_SAMPLES(rate, |
| dac33->mode1_latency); |
| nsample_limit = dac33->fifo_size - dac33->alarm_threshold; |
| |
| if (period_size <= dac33->alarm_threshold) |
| /* |
| * Configure nSamaple to number of periods, |
| * which covers the latency requironment. |
| */ |
| dac33->nsample = period_size * |
| ((dac33->alarm_threshold / period_size) + |
| (dac33->alarm_threshold % period_size ? |
| 1 : 0)); |
| else if (period_size > nsample_limit) |
| dac33->nsample = nsample_limit; |
| else |
| dac33->nsample = period_size; |
| |
| dac33->mode1_us_burst = SAMPLES_TO_US(dac33->burst_rate, |
| dac33->nsample); |
| dac33->t_stamp1 = 0; |
| dac33->t_stamp2 = 0; |
| break; |
| case DAC33_FIFO_MODE7: |
| dac33->uthr = UTHR_FROM_PERIOD_SIZE(period_size, rate, |
| dac33->burst_rate) + 9; |
| if (dac33->uthr > (dac33->fifo_size - DAC33_MODE7_MARGIN)) |
| dac33->uthr = dac33->fifo_size - DAC33_MODE7_MARGIN; |
| if (dac33->uthr < (DAC33_MODE7_MARGIN + 10)) |
| dac33->uthr = (DAC33_MODE7_MARGIN + 10); |
| |
| dac33->mode7_us_to_lthr = |
| SAMPLES_TO_US(substream->runtime->rate, |
| dac33->uthr - DAC33_MODE7_MARGIN + 1); |
| dac33->t_stamp1 = 0; |
| break; |
| default: |
| break; |
| } |
| |
| } |
| |
| static int dac33_pcm_trigger(struct snd_pcm_substream *substream, int cmd, |
| struct snd_soc_dai *dai) |
| { |
| struct snd_soc_component *component = dai->component; |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| int ret = 0; |
| |
| switch (cmd) { |
| case SNDRV_PCM_TRIGGER_START: |
| case SNDRV_PCM_TRIGGER_RESUME: |
| case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: |
| if (dac33->fifo_mode) { |
| dac33->state = DAC33_PREFILL; |
| schedule_work(&dac33->work); |
| } |
| break; |
| case SNDRV_PCM_TRIGGER_STOP: |
| case SNDRV_PCM_TRIGGER_SUSPEND: |
| case SNDRV_PCM_TRIGGER_PAUSE_PUSH: |
| if (dac33->fifo_mode) { |
| dac33->state = DAC33_FLUSH; |
| schedule_work(&dac33->work); |
| } |
| break; |
| default: |
| ret = -EINVAL; |
| } |
| |
| return ret; |
| } |
| |
| static snd_pcm_sframes_t dac33_dai_delay( |
| struct snd_pcm_substream *substream, |
| struct snd_soc_dai *dai) |
| { |
| struct snd_soc_component *component = dai->component; |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| unsigned long long t0, t1, t_now; |
| unsigned int time_delta, uthr; |
| int samples_out, samples_in, samples; |
| snd_pcm_sframes_t delay = 0; |
| unsigned long flags; |
| |
| switch (dac33->fifo_mode) { |
| case DAC33_FIFO_BYPASS: |
| break; |
| case DAC33_FIFO_MODE1: |
| spin_lock_irqsave(&dac33->lock, flags); |
| t0 = dac33->t_stamp1; |
| t1 = dac33->t_stamp2; |
| spin_unlock_irqrestore(&dac33->lock, flags); |
| t_now = ktime_to_us(ktime_get()); |
| |
| /* We have not started to fill the FIFO yet, delay is 0 */ |
| if (!t1) |
| goto out; |
| |
| if (t0 > t1) { |
| /* |
| * Phase 1: |
| * After Alarm threshold, and before nSample write |
| */ |
| time_delta = t_now - t0; |
| samples_out = time_delta ? US_TO_SAMPLES( |
| substream->runtime->rate, |
| time_delta) : 0; |
| |
| if (likely(dac33->alarm_threshold > samples_out)) |
| delay = dac33->alarm_threshold - samples_out; |
| else |
| delay = 0; |
| } else if ((t_now - t1) <= dac33->mode1_us_burst) { |
| /* |
| * Phase 2: |
| * After nSample write (during burst operation) |
| */ |
| time_delta = t_now - t0; |
| samples_out = time_delta ? US_TO_SAMPLES( |
| substream->runtime->rate, |
| time_delta) : 0; |
| |
| time_delta = t_now - t1; |
| samples_in = time_delta ? US_TO_SAMPLES( |
| dac33->burst_rate, |
| time_delta) : 0; |
| |
| samples = dac33->alarm_threshold; |
| samples += (samples_in - samples_out); |
| |
| if (likely(samples > 0)) |
| delay = samples; |
| else |
| delay = 0; |
| } else { |
| /* |
| * Phase 3: |
| * After burst operation, before next alarm threshold |
| */ |
| time_delta = t_now - t0; |
| samples_out = time_delta ? US_TO_SAMPLES( |
| substream->runtime->rate, |
| time_delta) : 0; |
| |
| samples_in = dac33->nsample; |
| samples = dac33->alarm_threshold; |
| samples += (samples_in - samples_out); |
| |
| if (likely(samples > 0)) |
| delay = samples > dac33->fifo_size ? |
| dac33->fifo_size : samples; |
| else |
| delay = 0; |
| } |
| break; |
| case DAC33_FIFO_MODE7: |
| spin_lock_irqsave(&dac33->lock, flags); |
| t0 = dac33->t_stamp1; |
| uthr = dac33->uthr; |
| spin_unlock_irqrestore(&dac33->lock, flags); |
| t_now = ktime_to_us(ktime_get()); |
| |
| /* We have not started to fill the FIFO yet, delay is 0 */ |
| if (!t0) |
| goto out; |
| |
| if (t_now <= t0) { |
| /* |
| * Either the timestamps are messed or equal. Report |
| * maximum delay |
| */ |
| delay = uthr; |
| goto out; |
| } |
| |
| time_delta = t_now - t0; |
| if (time_delta <= dac33->mode7_us_to_lthr) { |
| /* |
| * Phase 1: |
| * After burst (draining phase) |
| */ |
| samples_out = US_TO_SAMPLES( |
| substream->runtime->rate, |
| time_delta); |
| |
| if (likely(uthr > samples_out)) |
| delay = uthr - samples_out; |
| else |
| delay = 0; |
| } else { |
| /* |
| * Phase 2: |
| * During burst operation |
| */ |
| time_delta = time_delta - dac33->mode7_us_to_lthr; |
| |
| samples_out = US_TO_SAMPLES( |
| substream->runtime->rate, |
| time_delta); |
| samples_in = US_TO_SAMPLES( |
| dac33->burst_rate, |
| time_delta); |
| delay = DAC33_MODE7_MARGIN + samples_in - samples_out; |
| |
| if (unlikely(delay > uthr)) |
| delay = uthr; |
| } |
| break; |
| default: |
| dev_warn(component->dev, "Unhandled FIFO mode: %d\n", |
| dac33->fifo_mode); |
| break; |
| } |
| out: |
| return delay; |
| } |
| |
| static int dac33_set_dai_sysclk(struct snd_soc_dai *codec_dai, |
| int clk_id, unsigned int freq, int dir) |
| { |
| struct snd_soc_component *component = codec_dai->component; |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| u8 ioc_reg, asrcb_reg; |
| |
| ioc_reg = dac33_read_reg_cache(component, DAC33_INT_OSC_CTRL); |
| asrcb_reg = dac33_read_reg_cache(component, DAC33_ASRC_CTRL_B); |
| switch (clk_id) { |
| case TLV320DAC33_MCLK: |
| ioc_reg |= DAC33_REFSEL; |
| asrcb_reg |= DAC33_SRCREFSEL; |
| break; |
| case TLV320DAC33_SLEEPCLK: |
| ioc_reg &= ~DAC33_REFSEL; |
| asrcb_reg &= ~DAC33_SRCREFSEL; |
| break; |
| default: |
| dev_err(component->dev, "Invalid clock ID (%d)\n", clk_id); |
| break; |
| } |
| dac33->refclk = freq; |
| |
| dac33_write_reg_cache(component, DAC33_INT_OSC_CTRL, ioc_reg); |
| dac33_write_reg_cache(component, DAC33_ASRC_CTRL_B, asrcb_reg); |
| |
| return 0; |
| } |
| |
| static int dac33_set_dai_fmt(struct snd_soc_dai *codec_dai, |
| unsigned int fmt) |
| { |
| struct snd_soc_component *component = codec_dai->component; |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| u8 aictrl_a, aictrl_b; |
| |
| aictrl_a = dac33_read_reg_cache(component, DAC33_SER_AUDIOIF_CTRL_A); |
| aictrl_b = dac33_read_reg_cache(component, DAC33_SER_AUDIOIF_CTRL_B); |
| /* set master/slave audio interface */ |
| switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { |
| case SND_SOC_DAIFMT_CBM_CFM: |
| /* Codec Master */ |
| aictrl_a |= (DAC33_MSBCLK | DAC33_MSWCLK); |
| break; |
| case SND_SOC_DAIFMT_CBS_CFS: |
| /* Codec Slave */ |
| if (dac33->fifo_mode) { |
| dev_err(component->dev, "FIFO mode requires master mode\n"); |
| return -EINVAL; |
| } else |
| aictrl_a &= ~(DAC33_MSBCLK | DAC33_MSWCLK); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| aictrl_a &= ~DAC33_AFMT_MASK; |
| switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { |
| case SND_SOC_DAIFMT_I2S: |
| aictrl_a |= DAC33_AFMT_I2S; |
| break; |
| case SND_SOC_DAIFMT_DSP_A: |
| aictrl_a |= DAC33_AFMT_DSP; |
| aictrl_b &= ~DAC33_DATA_DELAY_MASK; |
| aictrl_b |= DAC33_DATA_DELAY(0); |
| break; |
| case SND_SOC_DAIFMT_RIGHT_J: |
| aictrl_a |= DAC33_AFMT_RIGHT_J; |
| break; |
| case SND_SOC_DAIFMT_LEFT_J: |
| aictrl_a |= DAC33_AFMT_LEFT_J; |
| break; |
| default: |
| dev_err(component->dev, "Unsupported format (%u)\n", |
| fmt & SND_SOC_DAIFMT_FORMAT_MASK); |
| return -EINVAL; |
| } |
| |
| dac33_write_reg_cache(component, DAC33_SER_AUDIOIF_CTRL_A, aictrl_a); |
| dac33_write_reg_cache(component, DAC33_SER_AUDIOIF_CTRL_B, aictrl_b); |
| |
| return 0; |
| } |
| |
| static int dac33_soc_probe(struct snd_soc_component *component) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| int ret = 0; |
| |
| dac33->component = component; |
| |
| /* Read the tlv320dac33 ID registers */ |
| ret = dac33_hard_power(component, 1); |
| if (ret != 0) { |
| dev_err(component->dev, "Failed to power up component: %d\n", ret); |
| goto err_power; |
| } |
| ret = dac33_read_id(component); |
| dac33_hard_power(component, 0); |
| |
| if (ret < 0) { |
| dev_err(component->dev, "Failed to read chip ID: %d\n", ret); |
| ret = -ENODEV; |
| goto err_power; |
| } |
| |
| /* Check if the IRQ number is valid and request it */ |
| if (dac33->irq >= 0) { |
| ret = request_irq(dac33->irq, dac33_interrupt_handler, |
| IRQF_TRIGGER_RISING, |
| component->name, component); |
| if (ret < 0) { |
| dev_err(component->dev, "Could not request IRQ%d (%d)\n", |
| dac33->irq, ret); |
| dac33->irq = -1; |
| } |
| if (dac33->irq != -1) { |
| INIT_WORK(&dac33->work, dac33_work); |
| } |
| } |
| |
| /* Only add the FIFO controls, if we have valid IRQ number */ |
| if (dac33->irq >= 0) |
| snd_soc_add_component_controls(component, dac33_mode_snd_controls, |
| ARRAY_SIZE(dac33_mode_snd_controls)); |
| |
| err_power: |
| return ret; |
| } |
| |
| static void dac33_soc_remove(struct snd_soc_component *component) |
| { |
| struct tlv320dac33_priv *dac33 = snd_soc_component_get_drvdata(component); |
| |
| if (dac33->irq >= 0) { |
| free_irq(dac33->irq, dac33->component); |
| flush_work(&dac33->work); |
| } |
| } |
| |
| static const struct snd_soc_component_driver soc_component_dev_tlv320dac33 = { |
| .read = dac33_read_reg_cache, |
| .write = dac33_write_locked, |
| .set_bias_level = dac33_set_bias_level, |
| .probe = dac33_soc_probe, |
| .remove = dac33_soc_remove, |
| .controls = dac33_snd_controls, |
| .num_controls = ARRAY_SIZE(dac33_snd_controls), |
| .dapm_widgets = dac33_dapm_widgets, |
| .num_dapm_widgets = ARRAY_SIZE(dac33_dapm_widgets), |
| .dapm_routes = audio_map, |
| .num_dapm_routes = ARRAY_SIZE(audio_map), |
| .use_pmdown_time = 1, |
| .endianness = 1, |
| .non_legacy_dai_naming = 1, |
| }; |
| |
| #define DAC33_RATES (SNDRV_PCM_RATE_44100 | \ |
| SNDRV_PCM_RATE_48000) |
| #define DAC33_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S32_LE) |
| |
| static const struct snd_soc_dai_ops dac33_dai_ops = { |
| .startup = dac33_startup, |
| .shutdown = dac33_shutdown, |
| .hw_params = dac33_hw_params, |
| .trigger = dac33_pcm_trigger, |
| .delay = dac33_dai_delay, |
| .set_sysclk = dac33_set_dai_sysclk, |
| .set_fmt = dac33_set_dai_fmt, |
| }; |
| |
| static struct snd_soc_dai_driver dac33_dai = { |
| .name = "tlv320dac33-hifi", |
| .playback = { |
| .stream_name = "Playback", |
| .channels_min = 2, |
| .channels_max = 2, |
| .rates = DAC33_RATES, |
| .formats = DAC33_FORMATS, |
| .sig_bits = 24, |
| }, |
| .ops = &dac33_dai_ops, |
| }; |
| |
| static int dac33_i2c_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct tlv320dac33_platform_data *pdata; |
| struct tlv320dac33_priv *dac33; |
| int ret, i; |
| |
| if (client->dev.platform_data == NULL) { |
| dev_err(&client->dev, "Platform data not set\n"); |
| return -ENODEV; |
| } |
| pdata = client->dev.platform_data; |
| |
| dac33 = devm_kzalloc(&client->dev, sizeof(struct tlv320dac33_priv), |
| GFP_KERNEL); |
| if (dac33 == NULL) |
| return -ENOMEM; |
| |
| dac33->reg_cache = devm_kmemdup(&client->dev, |
| dac33_reg, |
| ARRAY_SIZE(dac33_reg) * sizeof(u8), |
| GFP_KERNEL); |
| if (!dac33->reg_cache) |
| return -ENOMEM; |
| |
| dac33->i2c = client; |
| mutex_init(&dac33->mutex); |
| spin_lock_init(&dac33->lock); |
| |
| i2c_set_clientdata(client, dac33); |
| |
| dac33->power_gpio = pdata->power_gpio; |
| dac33->burst_bclkdiv = pdata->burst_bclkdiv; |
| dac33->keep_bclk = pdata->keep_bclk; |
| dac33->mode1_latency = pdata->mode1_latency; |
| if (!dac33->mode1_latency) |
| dac33->mode1_latency = 10000; /* 10ms */ |
| dac33->irq = client->irq; |
| /* Disable FIFO use by default */ |
| dac33->fifo_mode = DAC33_FIFO_BYPASS; |
| |
| /* Check if the reset GPIO number is valid and request it */ |
| if (dac33->power_gpio >= 0) { |
| ret = gpio_request(dac33->power_gpio, "tlv320dac33 reset"); |
| if (ret < 0) { |
| dev_err(&client->dev, |
| "Failed to request reset GPIO (%d)\n", |
| dac33->power_gpio); |
| goto err_gpio; |
| } |
| gpio_direction_output(dac33->power_gpio, 0); |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(dac33->supplies); i++) |
| dac33->supplies[i].supply = dac33_supply_names[i]; |
| |
| ret = devm_regulator_bulk_get(&client->dev, ARRAY_SIZE(dac33->supplies), |
| dac33->supplies); |
| |
| if (ret != 0) { |
| dev_err(&client->dev, "Failed to request supplies: %d\n", ret); |
| goto err_get; |
| } |
| |
| ret = devm_snd_soc_register_component(&client->dev, |
| &soc_component_dev_tlv320dac33, &dac33_dai, 1); |
| if (ret < 0) |
| goto err_get; |
| |
| return ret; |
| err_get: |
| if (dac33->power_gpio >= 0) |
| gpio_free(dac33->power_gpio); |
| err_gpio: |
| return ret; |
| } |
| |
| static int dac33_i2c_remove(struct i2c_client *client) |
| { |
| struct tlv320dac33_priv *dac33 = i2c_get_clientdata(client); |
| |
| if (unlikely(dac33->chip_power)) |
| dac33_hard_power(dac33->component, 0); |
| |
| if (dac33->power_gpio >= 0) |
| gpio_free(dac33->power_gpio); |
| |
| return 0; |
| } |
| |
| static const struct i2c_device_id tlv320dac33_i2c_id[] = { |
| { |
| .name = "tlv320dac33", |
| .driver_data = 0, |
| }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(i2c, tlv320dac33_i2c_id); |
| |
| static struct i2c_driver tlv320dac33_i2c_driver = { |
| .driver = { |
| .name = "tlv320dac33-codec", |
| }, |
| .probe = dac33_i2c_probe, |
| .remove = dac33_i2c_remove, |
| .id_table = tlv320dac33_i2c_id, |
| }; |
| |
| module_i2c_driver(tlv320dac33_i2c_driver); |
| |
| MODULE_DESCRIPTION("ASoC TLV320DAC33 codec driver"); |
| MODULE_AUTHOR("Peter Ujfalusi <peter.ujfalusi@ti.com>"); |
| MODULE_LICENSE("GPL"); |