| /* | |
| * Renesas R-Car USB phy driver | |
| * | |
| * Copyright (C) 2012 Renesas Solutions Corp. | |
| * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/io.h> | |
| #include <linux/usb/otg.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/module.h> | |
| /* USBH common register */ | |
| #define USBPCTRL0 0x0800 | |
| #define USBPCTRL1 0x0804 | |
| #define USBST 0x0808 | |
| #define USBEH0 0x080C | |
| #define USBOH0 0x081C | |
| #define USBCTL0 0x0858 | |
| #define EIIBC1 0x0094 | |
| #define EIIBC2 0x009C | |
| /* USBPCTRL1 */ | |
| #define PHY_RST (1 << 2) | |
| #define PLL_ENB (1 << 1) | |
| #define PHY_ENB (1 << 0) | |
| /* USBST */ | |
| #define ST_ACT (1 << 31) | |
| #define ST_PLL (1 << 30) | |
| struct rcar_usb_phy_priv { | |
| struct usb_phy phy; | |
| spinlock_t lock; | |
| void __iomem *reg0; | |
| void __iomem *reg1; | |
| int counter; | |
| }; | |
| #define usb_phy_to_priv(p) container_of(p, struct rcar_usb_phy_priv, phy) | |
| /* | |
| * USB initial/install operation. | |
| * | |
| * This function setup USB phy. | |
| * The used value and setting order came from | |
| * [USB :: Initial setting] on datasheet. | |
| */ | |
| static int rcar_usb_phy_init(struct usb_phy *phy) | |
| { | |
| struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy); | |
| struct device *dev = phy->dev; | |
| void __iomem *reg0 = priv->reg0; | |
| void __iomem *reg1 = priv->reg1; | |
| int i; | |
| u32 val; | |
| unsigned long flags; | |
| spin_lock_irqsave(&priv->lock, flags); | |
| if (priv->counter++ == 0) { | |
| /* | |
| * USB phy start-up | |
| */ | |
| /* (1) USB-PHY standby release */ | |
| iowrite32(PHY_ENB, (reg0 + USBPCTRL1)); | |
| /* (2) start USB-PHY internal PLL */ | |
| iowrite32(PHY_ENB | PLL_ENB, (reg0 + USBPCTRL1)); | |
| /* (3) USB module status check */ | |
| for (i = 0; i < 1024; i++) { | |
| udelay(10); | |
| val = ioread32(reg0 + USBST); | |
| if (val == (ST_ACT | ST_PLL)) | |
| break; | |
| } | |
| if (val != (ST_ACT | ST_PLL)) { | |
| dev_err(dev, "USB phy not ready\n"); | |
| goto phy_init_end; | |
| } | |
| /* (4) USB-PHY reset clear */ | |
| iowrite32(PHY_ENB | PLL_ENB | PHY_RST, (reg0 + USBPCTRL1)); | |
| /* set platform specific port settings */ | |
| iowrite32(0x00000000, (reg0 + USBPCTRL0)); | |
| /* | |
| * EHCI IP internal buffer setting | |
| * EHCI IP internal buffer enable | |
| * | |
| * These are recommended value of a datasheet | |
| * see [USB :: EHCI internal buffer setting] | |
| */ | |
| iowrite32(0x00ff0040, (reg0 + EIIBC1)); | |
| iowrite32(0x00ff0040, (reg1 + EIIBC1)); | |
| iowrite32(0x00000001, (reg0 + EIIBC2)); | |
| iowrite32(0x00000001, (reg1 + EIIBC2)); | |
| /* | |
| * Bus alignment settings | |
| */ | |
| /* (1) EHCI bus alignment (little endian) */ | |
| iowrite32(0x00000000, (reg0 + USBEH0)); | |
| /* (1) OHCI bus alignment (little endian) */ | |
| iowrite32(0x00000000, (reg0 + USBOH0)); | |
| } | |
| phy_init_end: | |
| spin_unlock_irqrestore(&priv->lock, flags); | |
| return 0; | |
| } | |
| static void rcar_usb_phy_shutdown(struct usb_phy *phy) | |
| { | |
| struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy); | |
| void __iomem *reg0 = priv->reg0; | |
| unsigned long flags; | |
| spin_lock_irqsave(&priv->lock, flags); | |
| if (priv->counter-- == 1) { /* last user */ | |
| iowrite32(0x00000000, (reg0 + USBPCTRL0)); | |
| iowrite32(0x00000000, (reg0 + USBPCTRL1)); | |
| } | |
| spin_unlock_irqrestore(&priv->lock, flags); | |
| } | |
| static int rcar_usb_phy_probe(struct platform_device *pdev) | |
| { | |
| struct rcar_usb_phy_priv *priv; | |
| struct resource *res0, *res1; | |
| struct device *dev = &pdev->dev; | |
| void __iomem *reg0, *reg1; | |
| int ret; | |
| res0 = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| res1 = platform_get_resource(pdev, IORESOURCE_MEM, 1); | |
| if (!res0 || !res1) { | |
| dev_err(dev, "Not enough platform resources\n"); | |
| return -EINVAL; | |
| } | |
| /* | |
| * CAUTION | |
| * | |
| * Because this phy address is also mapped under OHCI/EHCI address area, | |
| * this driver can't use devm_request_and_ioremap(dev, res) here | |
| */ | |
| reg0 = devm_ioremap_nocache(dev, res0->start, resource_size(res0)); | |
| reg1 = devm_ioremap_nocache(dev, res1->start, resource_size(res1)); | |
| if (!reg0 || !reg1) { | |
| dev_err(dev, "ioremap error\n"); | |
| return -ENOMEM; | |
| } | |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); | |
| if (!priv) { | |
| dev_err(dev, "priv data allocation error\n"); | |
| return -ENOMEM; | |
| } | |
| priv->reg0 = reg0; | |
| priv->reg1 = reg1; | |
| priv->counter = 0; | |
| priv->phy.dev = dev; | |
| priv->phy.label = dev_name(dev); | |
| priv->phy.init = rcar_usb_phy_init; | |
| priv->phy.shutdown = rcar_usb_phy_shutdown; | |
| spin_lock_init(&priv->lock); | |
| ret = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2); | |
| if (ret < 0) { | |
| dev_err(dev, "usb phy addition error\n"); | |
| return ret; | |
| } | |
| platform_set_drvdata(pdev, priv); | |
| return ret; | |
| } | |
| static int rcar_usb_phy_remove(struct platform_device *pdev) | |
| { | |
| struct rcar_usb_phy_priv *priv = platform_get_drvdata(pdev); | |
| usb_remove_phy(&priv->phy); | |
| return 0; | |
| } | |
| static struct platform_driver rcar_usb_phy_driver = { | |
| .driver = { | |
| .name = "rcar_usb_phy", | |
| }, | |
| .probe = rcar_usb_phy_probe, | |
| .remove = rcar_usb_phy_remove, | |
| }; | |
| module_platform_driver(rcar_usb_phy_driver); | |
| MODULE_LICENSE("GPL v2"); | |
| MODULE_DESCRIPTION("Renesas R-Car USB phy"); | |
| MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>"); |