| /* |
| * MCP23S08 SPI/GPIO gpio expander driver |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/device.h> |
| #include <linux/mutex.h> |
| #include <linux/module.h> |
| #include <linux/gpio.h> |
| #include <linux/i2c.h> |
| #include <linux/spi/spi.h> |
| #include <linux/spi/mcp23s08.h> |
| #include <linux/slab.h> |
| #include <asm/byteorder.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| |
| /** |
| * MCP types supported by driver |
| */ |
| #define MCP_TYPE_S08 0 |
| #define MCP_TYPE_S17 1 |
| #define MCP_TYPE_008 2 |
| #define MCP_TYPE_017 3 |
| |
| /* Registers are all 8 bits wide. |
| * |
| * The mcp23s17 has twice as many bits, and can be configured to work |
| * with either 16 bit registers or with two adjacent 8 bit banks. |
| */ |
| #define MCP_IODIR 0x00 /* init/reset: all ones */ |
| #define MCP_IPOL 0x01 |
| #define MCP_GPINTEN 0x02 |
| #define MCP_DEFVAL 0x03 |
| #define MCP_INTCON 0x04 |
| #define MCP_IOCON 0x05 |
| # define IOCON_SEQOP (1 << 5) |
| # define IOCON_HAEN (1 << 3) |
| # define IOCON_ODR (1 << 2) |
| # define IOCON_INTPOL (1 << 1) |
| #define MCP_GPPU 0x06 |
| #define MCP_INTF 0x07 |
| #define MCP_INTCAP 0x08 |
| #define MCP_GPIO 0x09 |
| #define MCP_OLAT 0x0a |
| |
| struct mcp23s08; |
| |
| struct mcp23s08_ops { |
| int (*read)(struct mcp23s08 *mcp, unsigned reg); |
| int (*write)(struct mcp23s08 *mcp, unsigned reg, unsigned val); |
| int (*read_regs)(struct mcp23s08 *mcp, unsigned reg, |
| u16 *vals, unsigned n); |
| }; |
| |
| struct mcp23s08 { |
| u8 addr; |
| |
| u16 cache[11]; |
| /* lock protects the cached values */ |
| struct mutex lock; |
| |
| struct gpio_chip chip; |
| |
| const struct mcp23s08_ops *ops; |
| void *data; /* ops specific data */ |
| }; |
| |
| /* A given spi_device can represent up to eight mcp23sxx chips |
| * sharing the same chipselect but using different addresses |
| * (e.g. chips #0 and #3 might be populated, but not #1 or $2). |
| * Driver data holds all the per-chip data. |
| */ |
| struct mcp23s08_driver_data { |
| unsigned ngpio; |
| struct mcp23s08 *mcp[8]; |
| struct mcp23s08 chip[]; |
| }; |
| |
| /*----------------------------------------------------------------------*/ |
| |
| #if IS_ENABLED(CONFIG_I2C) |
| |
| static int mcp23008_read(struct mcp23s08 *mcp, unsigned reg) |
| { |
| return i2c_smbus_read_byte_data(mcp->data, reg); |
| } |
| |
| static int mcp23008_write(struct mcp23s08 *mcp, unsigned reg, unsigned val) |
| { |
| return i2c_smbus_write_byte_data(mcp->data, reg, val); |
| } |
| |
| static int |
| mcp23008_read_regs(struct mcp23s08 *mcp, unsigned reg, u16 *vals, unsigned n) |
| { |
| while (n--) { |
| int ret = mcp23008_read(mcp, reg++); |
| if (ret < 0) |
| return ret; |
| *vals++ = ret; |
| } |
| |
| return 0; |
| } |
| |
| static int mcp23017_read(struct mcp23s08 *mcp, unsigned reg) |
| { |
| return i2c_smbus_read_word_data(mcp->data, reg << 1); |
| } |
| |
| static int mcp23017_write(struct mcp23s08 *mcp, unsigned reg, unsigned val) |
| { |
| return i2c_smbus_write_word_data(mcp->data, reg << 1, val); |
| } |
| |
| static int |
| mcp23017_read_regs(struct mcp23s08 *mcp, unsigned reg, u16 *vals, unsigned n) |
| { |
| while (n--) { |
| int ret = mcp23017_read(mcp, reg++); |
| if (ret < 0) |
| return ret; |
| *vals++ = ret; |
| } |
| |
| return 0; |
| } |
| |
| static const struct mcp23s08_ops mcp23008_ops = { |
| .read = mcp23008_read, |
| .write = mcp23008_write, |
| .read_regs = mcp23008_read_regs, |
| }; |
| |
| static const struct mcp23s08_ops mcp23017_ops = { |
| .read = mcp23017_read, |
| .write = mcp23017_write, |
| .read_regs = mcp23017_read_regs, |
| }; |
| |
| #endif /* CONFIG_I2C */ |
| |
| /*----------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_SPI_MASTER |
| |
| static int mcp23s08_read(struct mcp23s08 *mcp, unsigned reg) |
| { |
| u8 tx[2], rx[1]; |
| int status; |
| |
| tx[0] = mcp->addr | 0x01; |
| tx[1] = reg; |
| status = spi_write_then_read(mcp->data, tx, sizeof tx, rx, sizeof rx); |
| return (status < 0) ? status : rx[0]; |
| } |
| |
| static int mcp23s08_write(struct mcp23s08 *mcp, unsigned reg, unsigned val) |
| { |
| u8 tx[3]; |
| |
| tx[0] = mcp->addr; |
| tx[1] = reg; |
| tx[2] = val; |
| return spi_write_then_read(mcp->data, tx, sizeof tx, NULL, 0); |
| } |
| |
| static int |
| mcp23s08_read_regs(struct mcp23s08 *mcp, unsigned reg, u16 *vals, unsigned n) |
| { |
| u8 tx[2], *tmp; |
| int status; |
| |
| if ((n + reg) > sizeof mcp->cache) |
| return -EINVAL; |
| tx[0] = mcp->addr | 0x01; |
| tx[1] = reg; |
| |
| tmp = (u8 *)vals; |
| status = spi_write_then_read(mcp->data, tx, sizeof tx, tmp, n); |
| if (status >= 0) { |
| while (n--) |
| vals[n] = tmp[n]; /* expand to 16bit */ |
| } |
| return status; |
| } |
| |
| static int mcp23s17_read(struct mcp23s08 *mcp, unsigned reg) |
| { |
| u8 tx[2], rx[2]; |
| int status; |
| |
| tx[0] = mcp->addr | 0x01; |
| tx[1] = reg << 1; |
| status = spi_write_then_read(mcp->data, tx, sizeof tx, rx, sizeof rx); |
| return (status < 0) ? status : (rx[0] | (rx[1] << 8)); |
| } |
| |
| static int mcp23s17_write(struct mcp23s08 *mcp, unsigned reg, unsigned val) |
| { |
| u8 tx[4]; |
| |
| tx[0] = mcp->addr; |
| tx[1] = reg << 1; |
| tx[2] = val; |
| tx[3] = val >> 8; |
| return spi_write_then_read(mcp->data, tx, sizeof tx, NULL, 0); |
| } |
| |
| static int |
| mcp23s17_read_regs(struct mcp23s08 *mcp, unsigned reg, u16 *vals, unsigned n) |
| { |
| u8 tx[2]; |
| int status; |
| |
| if ((n + reg) > sizeof mcp->cache) |
| return -EINVAL; |
| tx[0] = mcp->addr | 0x01; |
| tx[1] = reg << 1; |
| |
| status = spi_write_then_read(mcp->data, tx, sizeof tx, |
| (u8 *)vals, n * 2); |
| if (status >= 0) { |
| while (n--) |
| vals[n] = __le16_to_cpu((__le16)vals[n]); |
| } |
| |
| return status; |
| } |
| |
| static const struct mcp23s08_ops mcp23s08_ops = { |
| .read = mcp23s08_read, |
| .write = mcp23s08_write, |
| .read_regs = mcp23s08_read_regs, |
| }; |
| |
| static const struct mcp23s08_ops mcp23s17_ops = { |
| .read = mcp23s17_read, |
| .write = mcp23s17_write, |
| .read_regs = mcp23s17_read_regs, |
| }; |
| |
| #endif /* CONFIG_SPI_MASTER */ |
| |
| /*----------------------------------------------------------------------*/ |
| |
| static int mcp23s08_direction_input(struct gpio_chip *chip, unsigned offset) |
| { |
| struct mcp23s08 *mcp = container_of(chip, struct mcp23s08, chip); |
| int status; |
| |
| mutex_lock(&mcp->lock); |
| mcp->cache[MCP_IODIR] |= (1 << offset); |
| status = mcp->ops->write(mcp, MCP_IODIR, mcp->cache[MCP_IODIR]); |
| mutex_unlock(&mcp->lock); |
| return status; |
| } |
| |
| static int mcp23s08_get(struct gpio_chip *chip, unsigned offset) |
| { |
| struct mcp23s08 *mcp = container_of(chip, struct mcp23s08, chip); |
| int status; |
| |
| mutex_lock(&mcp->lock); |
| |
| /* REVISIT reading this clears any IRQ ... */ |
| status = mcp->ops->read(mcp, MCP_GPIO); |
| if (status < 0) |
| status = 0; |
| else { |
| mcp->cache[MCP_GPIO] = status; |
| status = !!(status & (1 << offset)); |
| } |
| mutex_unlock(&mcp->lock); |
| return status; |
| } |
| |
| static int __mcp23s08_set(struct mcp23s08 *mcp, unsigned mask, int value) |
| { |
| unsigned olat = mcp->cache[MCP_OLAT]; |
| |
| if (value) |
| olat |= mask; |
| else |
| olat &= ~mask; |
| mcp->cache[MCP_OLAT] = olat; |
| return mcp->ops->write(mcp, MCP_OLAT, olat); |
| } |
| |
| static void mcp23s08_set(struct gpio_chip *chip, unsigned offset, int value) |
| { |
| struct mcp23s08 *mcp = container_of(chip, struct mcp23s08, chip); |
| unsigned mask = 1 << offset; |
| |
| mutex_lock(&mcp->lock); |
| __mcp23s08_set(mcp, mask, value); |
| mutex_unlock(&mcp->lock); |
| } |
| |
| static int |
| mcp23s08_direction_output(struct gpio_chip *chip, unsigned offset, int value) |
| { |
| struct mcp23s08 *mcp = container_of(chip, struct mcp23s08, chip); |
| unsigned mask = 1 << offset; |
| int status; |
| |
| mutex_lock(&mcp->lock); |
| status = __mcp23s08_set(mcp, mask, value); |
| if (status == 0) { |
| mcp->cache[MCP_IODIR] &= ~mask; |
| status = mcp->ops->write(mcp, MCP_IODIR, mcp->cache[MCP_IODIR]); |
| } |
| mutex_unlock(&mcp->lock); |
| return status; |
| } |
| |
| /*----------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_DEBUG_FS |
| |
| #include <linux/seq_file.h> |
| |
| /* |
| * This shows more info than the generic gpio dump code: |
| * pullups, deglitching, open drain drive. |
| */ |
| static void mcp23s08_dbg_show(struct seq_file *s, struct gpio_chip *chip) |
| { |
| struct mcp23s08 *mcp; |
| char bank; |
| int t; |
| unsigned mask; |
| |
| mcp = container_of(chip, struct mcp23s08, chip); |
| |
| /* NOTE: we only handle one bank for now ... */ |
| bank = '0' + ((mcp->addr >> 1) & 0x7); |
| |
| mutex_lock(&mcp->lock); |
| t = mcp->ops->read_regs(mcp, 0, mcp->cache, ARRAY_SIZE(mcp->cache)); |
| if (t < 0) { |
| seq_printf(s, " I/O ERROR %d\n", t); |
| goto done; |
| } |
| |
| for (t = 0, mask = 1; t < chip->ngpio; t++, mask <<= 1) { |
| const char *label; |
| |
| label = gpiochip_is_requested(chip, t); |
| if (!label) |
| continue; |
| |
| seq_printf(s, " gpio-%-3d P%c.%d (%-12s) %s %s %s", |
| chip->base + t, bank, t, label, |
| (mcp->cache[MCP_IODIR] & mask) ? "in " : "out", |
| (mcp->cache[MCP_GPIO] & mask) ? "hi" : "lo", |
| (mcp->cache[MCP_GPPU] & mask) ? "up" : " "); |
| /* NOTE: ignoring the irq-related registers */ |
| seq_printf(s, "\n"); |
| } |
| done: |
| mutex_unlock(&mcp->lock); |
| } |
| |
| #else |
| #define mcp23s08_dbg_show NULL |
| #endif |
| |
| /*----------------------------------------------------------------------*/ |
| |
| static int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev, |
| void *data, unsigned addr, |
| unsigned type, unsigned base, unsigned pullups) |
| { |
| int status; |
| |
| mutex_init(&mcp->lock); |
| |
| mcp->data = data; |
| mcp->addr = addr; |
| |
| mcp->chip.direction_input = mcp23s08_direction_input; |
| mcp->chip.get = mcp23s08_get; |
| mcp->chip.direction_output = mcp23s08_direction_output; |
| mcp->chip.set = mcp23s08_set; |
| mcp->chip.dbg_show = mcp23s08_dbg_show; |
| #ifdef CONFIG_OF |
| mcp->chip.of_gpio_n_cells = 2; |
| mcp->chip.of_node = dev->of_node; |
| #endif |
| |
| switch (type) { |
| #ifdef CONFIG_SPI_MASTER |
| case MCP_TYPE_S08: |
| mcp->ops = &mcp23s08_ops; |
| mcp->chip.ngpio = 8; |
| mcp->chip.label = "mcp23s08"; |
| break; |
| |
| case MCP_TYPE_S17: |
| mcp->ops = &mcp23s17_ops; |
| mcp->chip.ngpio = 16; |
| mcp->chip.label = "mcp23s17"; |
| break; |
| #endif /* CONFIG_SPI_MASTER */ |
| |
| #if IS_ENABLED(CONFIG_I2C) |
| case MCP_TYPE_008: |
| mcp->ops = &mcp23008_ops; |
| mcp->chip.ngpio = 8; |
| mcp->chip.label = "mcp23008"; |
| break; |
| |
| case MCP_TYPE_017: |
| mcp->ops = &mcp23017_ops; |
| mcp->chip.ngpio = 16; |
| mcp->chip.label = "mcp23017"; |
| break; |
| #endif /* CONFIG_I2C */ |
| |
| default: |
| dev_err(dev, "invalid device type (%d)\n", type); |
| return -EINVAL; |
| } |
| |
| mcp->chip.base = base; |
| mcp->chip.can_sleep = true; |
| mcp->chip.dev = dev; |
| mcp->chip.owner = THIS_MODULE; |
| |
| /* verify MCP_IOCON.SEQOP = 0, so sequential reads work, |
| * and MCP_IOCON.HAEN = 1, so we work with all chips. |
| */ |
| status = mcp->ops->read(mcp, MCP_IOCON); |
| if (status < 0) |
| goto fail; |
| if ((status & IOCON_SEQOP) || !(status & IOCON_HAEN)) { |
| /* mcp23s17 has IOCON twice, make sure they are in sync */ |
| status &= ~(IOCON_SEQOP | (IOCON_SEQOP << 8)); |
| status |= IOCON_HAEN | (IOCON_HAEN << 8); |
| status = mcp->ops->write(mcp, MCP_IOCON, status); |
| if (status < 0) |
| goto fail; |
| } |
| |
| /* configure ~100K pullups */ |
| status = mcp->ops->write(mcp, MCP_GPPU, pullups); |
| if (status < 0) |
| goto fail; |
| |
| status = mcp->ops->read_regs(mcp, 0, mcp->cache, ARRAY_SIZE(mcp->cache)); |
| if (status < 0) |
| goto fail; |
| |
| /* disable inverter on input */ |
| if (mcp->cache[MCP_IPOL] != 0) { |
| mcp->cache[MCP_IPOL] = 0; |
| status = mcp->ops->write(mcp, MCP_IPOL, 0); |
| if (status < 0) |
| goto fail; |
| } |
| |
| /* disable irqs */ |
| if (mcp->cache[MCP_GPINTEN] != 0) { |
| mcp->cache[MCP_GPINTEN] = 0; |
| status = mcp->ops->write(mcp, MCP_GPINTEN, 0); |
| if (status < 0) |
| goto fail; |
| } |
| |
| status = gpiochip_add(&mcp->chip); |
| fail: |
| if (status < 0) |
| dev_dbg(dev, "can't setup chip %d, --> %d\n", |
| addr, status); |
| return status; |
| } |
| |
| /*----------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_OF |
| #ifdef CONFIG_SPI_MASTER |
| static struct of_device_id mcp23s08_spi_of_match[] = { |
| { |
| .compatible = "microchip,mcp23s08", |
| .data = (void *) MCP_TYPE_S08, |
| }, |
| { |
| .compatible = "microchip,mcp23s17", |
| .data = (void *) MCP_TYPE_S17, |
| }, |
| /* NOTE: The use of the mcp prefix is deprecated and will be removed. */ |
| { |
| .compatible = "mcp,mcp23s08", |
| .data = (void *) MCP_TYPE_S08, |
| }, |
| { |
| .compatible = "mcp,mcp23s17", |
| .data = (void *) MCP_TYPE_S17, |
| }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, mcp23s08_spi_of_match); |
| #endif |
| |
| #if IS_ENABLED(CONFIG_I2C) |
| static struct of_device_id mcp23s08_i2c_of_match[] = { |
| { |
| .compatible = "microchip,mcp23008", |
| .data = (void *) MCP_TYPE_008, |
| }, |
| { |
| .compatible = "microchip,mcp23017", |
| .data = (void *) MCP_TYPE_017, |
| }, |
| /* NOTE: The use of the mcp prefix is deprecated and will be removed. */ |
| { |
| .compatible = "mcp,mcp23008", |
| .data = (void *) MCP_TYPE_008, |
| }, |
| { |
| .compatible = "mcp,mcp23017", |
| .data = (void *) MCP_TYPE_017, |
| }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, mcp23s08_i2c_of_match); |
| #endif |
| #endif /* CONFIG_OF */ |
| |
| |
| #if IS_ENABLED(CONFIG_I2C) |
| |
| static int mcp230xx_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct mcp23s08_platform_data *pdata; |
| struct mcp23s08 *mcp; |
| int status, base, pullups; |
| const struct of_device_id *match; |
| |
| match = of_match_device(of_match_ptr(mcp23s08_i2c_of_match), |
| &client->dev); |
| pdata = dev_get_platdata(&client->dev); |
| if (match || !pdata) { |
| base = -1; |
| pullups = 0; |
| } else { |
| if (!gpio_is_valid(pdata->base)) { |
| dev_dbg(&client->dev, "invalid platform data\n"); |
| return -EINVAL; |
| } |
| base = pdata->base; |
| pullups = pdata->chip[0].pullups; |
| } |
| |
| mcp = kzalloc(sizeof *mcp, GFP_KERNEL); |
| if (!mcp) |
| return -ENOMEM; |
| |
| status = mcp23s08_probe_one(mcp, &client->dev, client, client->addr, |
| id->driver_data, base, pullups); |
| if (status) |
| goto fail; |
| |
| i2c_set_clientdata(client, mcp); |
| |
| return 0; |
| |
| fail: |
| kfree(mcp); |
| |
| return status; |
| } |
| |
| static int mcp230xx_remove(struct i2c_client *client) |
| { |
| struct mcp23s08 *mcp = i2c_get_clientdata(client); |
| int status; |
| |
| status = gpiochip_remove(&mcp->chip); |
| if (status == 0) |
| kfree(mcp); |
| |
| return status; |
| } |
| |
| static const struct i2c_device_id mcp230xx_id[] = { |
| { "mcp23008", MCP_TYPE_008 }, |
| { "mcp23017", MCP_TYPE_017 }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(i2c, mcp230xx_id); |
| |
| static struct i2c_driver mcp230xx_driver = { |
| .driver = { |
| .name = "mcp230xx", |
| .owner = THIS_MODULE, |
| .of_match_table = of_match_ptr(mcp23s08_i2c_of_match), |
| }, |
| .probe = mcp230xx_probe, |
| .remove = mcp230xx_remove, |
| .id_table = mcp230xx_id, |
| }; |
| |
| static int __init mcp23s08_i2c_init(void) |
| { |
| return i2c_add_driver(&mcp230xx_driver); |
| } |
| |
| static void mcp23s08_i2c_exit(void) |
| { |
| i2c_del_driver(&mcp230xx_driver); |
| } |
| |
| #else |
| |
| static int __init mcp23s08_i2c_init(void) { return 0; } |
| static void mcp23s08_i2c_exit(void) { } |
| |
| #endif /* CONFIG_I2C */ |
| |
| /*----------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_SPI_MASTER |
| |
| static int mcp23s08_probe(struct spi_device *spi) |
| { |
| struct mcp23s08_platform_data *pdata; |
| unsigned addr; |
| unsigned chips = 0; |
| struct mcp23s08_driver_data *data; |
| int status, type; |
| unsigned base = -1, |
| ngpio = 0, |
| pullups[ARRAY_SIZE(pdata->chip)]; |
| const struct of_device_id *match; |
| u32 spi_present_mask = 0; |
| |
| match = of_match_device(of_match_ptr(mcp23s08_spi_of_match), &spi->dev); |
| if (match) { |
| type = (int)match->data; |
| status = of_property_read_u32(spi->dev.of_node, |
| "microchip,spi-present-mask", &spi_present_mask); |
| if (status) { |
| status = of_property_read_u32(spi->dev.of_node, |
| "mcp,spi-present-mask", &spi_present_mask); |
| if (status) { |
| dev_err(&spi->dev, |
| "DT has no spi-present-mask\n"); |
| return -ENODEV; |
| } |
| } |
| if ((spi_present_mask <= 0) || (spi_present_mask >= 256)) { |
| dev_err(&spi->dev, "invalid spi-present-mask\n"); |
| return -ENODEV; |
| } |
| |
| for (addr = 0; addr < ARRAY_SIZE(pdata->chip); addr++) |
| pullups[addr] = 0; |
| } else { |
| type = spi_get_device_id(spi)->driver_data; |
| pdata = dev_get_platdata(&spi->dev); |
| if (!pdata || !gpio_is_valid(pdata->base)) { |
| dev_dbg(&spi->dev, |
| "invalid or missing platform data\n"); |
| return -EINVAL; |
| } |
| |
| for (addr = 0; addr < ARRAY_SIZE(pdata->chip); addr++) { |
| if (!pdata->chip[addr].is_present) |
| continue; |
| chips++; |
| if ((type == MCP_TYPE_S08) && (addr > 3)) { |
| dev_err(&spi->dev, |
| "mcp23s08 only supports address 0..3\n"); |
| return -EINVAL; |
| } |
| spi_present_mask |= 1 << addr; |
| pullups[addr] = pdata->chip[addr].pullups; |
| } |
| |
| if (!chips) |
| return -ENODEV; |
| |
| base = pdata->base; |
| } |
| |
| data = kzalloc(sizeof *data + chips * sizeof(struct mcp23s08), |
| GFP_KERNEL); |
| if (!data) |
| return -ENOMEM; |
| spi_set_drvdata(spi, data); |
| |
| for (addr = 0; addr < ARRAY_SIZE(pdata->chip); addr++) { |
| if (!(spi_present_mask & (1 << addr))) |
| continue; |
| chips--; |
| data->mcp[addr] = &data->chip[chips]; |
| status = mcp23s08_probe_one(data->mcp[addr], &spi->dev, spi, |
| 0x40 | (addr << 1), type, base, |
| pullups[addr]); |
| if (status < 0) |
| goto fail; |
| |
| if (base != -1) |
| base += (type == MCP_TYPE_S17) ? 16 : 8; |
| ngpio += (type == MCP_TYPE_S17) ? 16 : 8; |
| } |
| data->ngpio = ngpio; |
| |
| /* NOTE: these chips have a relatively sane IRQ framework, with |
| * per-signal masking and level/edge triggering. It's not yet |
| * handled here... |
| */ |
| |
| return 0; |
| |
| fail: |
| for (addr = 0; addr < ARRAY_SIZE(data->mcp); addr++) { |
| int tmp; |
| |
| if (!data->mcp[addr]) |
| continue; |
| tmp = gpiochip_remove(&data->mcp[addr]->chip); |
| if (tmp < 0) |
| dev_err(&spi->dev, "%s --> %d\n", "remove", tmp); |
| } |
| kfree(data); |
| return status; |
| } |
| |
| static int mcp23s08_remove(struct spi_device *spi) |
| { |
| struct mcp23s08_driver_data *data = spi_get_drvdata(spi); |
| unsigned addr; |
| int status = 0; |
| |
| for (addr = 0; addr < ARRAY_SIZE(data->mcp); addr++) { |
| int tmp; |
| |
| if (!data->mcp[addr]) |
| continue; |
| |
| tmp = gpiochip_remove(&data->mcp[addr]->chip); |
| if (tmp < 0) { |
| dev_err(&spi->dev, "%s --> %d\n", "remove", tmp); |
| status = tmp; |
| } |
| } |
| if (status == 0) |
| kfree(data); |
| return status; |
| } |
| |
| static const struct spi_device_id mcp23s08_ids[] = { |
| { "mcp23s08", MCP_TYPE_S08 }, |
| { "mcp23s17", MCP_TYPE_S17 }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(spi, mcp23s08_ids); |
| |
| static struct spi_driver mcp23s08_driver = { |
| .probe = mcp23s08_probe, |
| .remove = mcp23s08_remove, |
| .id_table = mcp23s08_ids, |
| .driver = { |
| .name = "mcp23s08", |
| .owner = THIS_MODULE, |
| .of_match_table = of_match_ptr(mcp23s08_spi_of_match), |
| }, |
| }; |
| |
| static int __init mcp23s08_spi_init(void) |
| { |
| return spi_register_driver(&mcp23s08_driver); |
| } |
| |
| static void mcp23s08_spi_exit(void) |
| { |
| spi_unregister_driver(&mcp23s08_driver); |
| } |
| |
| #else |
| |
| static int __init mcp23s08_spi_init(void) { return 0; } |
| static void mcp23s08_spi_exit(void) { } |
| |
| #endif /* CONFIG_SPI_MASTER */ |
| |
| /*----------------------------------------------------------------------*/ |
| |
| static int __init mcp23s08_init(void) |
| { |
| int ret; |
| |
| ret = mcp23s08_spi_init(); |
| if (ret) |
| goto spi_fail; |
| |
| ret = mcp23s08_i2c_init(); |
| if (ret) |
| goto i2c_fail; |
| |
| return 0; |
| |
| i2c_fail: |
| mcp23s08_spi_exit(); |
| spi_fail: |
| return ret; |
| } |
| /* register after spi/i2c postcore initcall and before |
| * subsys initcalls that may rely on these GPIOs |
| */ |
| subsys_initcall(mcp23s08_init); |
| |
| static void __exit mcp23s08_exit(void) |
| { |
| mcp23s08_spi_exit(); |
| mcp23s08_i2c_exit(); |
| } |
| module_exit(mcp23s08_exit); |
| |
| MODULE_LICENSE("GPL"); |