| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Support for common PCI multi-I/O cards (which is most of them) |
| * |
| * Copyright (C) 2001 Tim Waugh <twaugh@redhat.com> |
| * |
| * Multi-function PCI cards are supposed to present separate logical |
| * devices on the bus. A common thing to do seems to be to just use |
| * one logical device with lots of base address registers for both |
| * parallel ports and serial ports. This driver is for dealing with |
| * that. |
| */ |
| |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/parport.h> |
| #include <linux/parport_pc.h> |
| #include <linux/pci.h> |
| #include <linux/slab.h> |
| #include <linux/types.h> |
| |
| #include <linux/8250_pci.h> |
| |
| enum parport_pc_pci_cards { |
| titan_110l = 0, |
| titan_210l, |
| netmos_9xx5_combo, |
| netmos_9855, |
| netmos_9855_2p, |
| netmos_9900, |
| netmos_9900_2p, |
| netmos_99xx_1p, |
| avlab_1s1p, |
| avlab_1s2p, |
| avlab_2s1p, |
| siig_1s1p_10x, |
| siig_2s1p_10x, |
| siig_2p1s_20x, |
| siig_1s1p_20x, |
| siig_2s1p_20x, |
| timedia_4078a, |
| timedia_4079h, |
| timedia_4085h, |
| timedia_4088a, |
| timedia_4089a, |
| timedia_4095a, |
| timedia_4096a, |
| timedia_4078u, |
| timedia_4079a, |
| timedia_4085u, |
| timedia_4079r, |
| timedia_4079s, |
| timedia_4079d, |
| timedia_4079e, |
| timedia_4079f, |
| timedia_9079a, |
| timedia_9079b, |
| timedia_9079c, |
| wch_ch353_1s1p, |
| wch_ch353_2s1p, |
| wch_ch382_0s1p, |
| wch_ch382_2s1p, |
| brainboxes_5s1p, |
| sunix_2s1p, |
| }; |
| |
| /* each element directly indexed from enum list, above */ |
| struct parport_pc_pci { |
| int numports; |
| struct { /* BAR (base address registers) numbers in the config |
| space header */ |
| int lo; |
| int hi; /* -1 if not there, >6 for offset-method (max |
| BAR is 6) */ |
| } addr[4]; |
| |
| /* If set, this is called immediately after pci_enable_device. |
| * If it returns non-zero, no probing will take place and the |
| * ports will not be used. */ |
| int (*preinit_hook) (struct pci_dev *pdev, struct parport_pc_pci *card, |
| int autoirq, int autodma); |
| |
| /* If set, this is called after probing for ports. If 'failed' |
| * is non-zero we couldn't use any of the ports. */ |
| void (*postinit_hook) (struct pci_dev *pdev, |
| struct parport_pc_pci *card, int failed); |
| }; |
| |
| static int netmos_parallel_init(struct pci_dev *dev, struct parport_pc_pci *par, |
| int autoirq, int autodma) |
| { |
| /* the rule described below doesn't hold for this device */ |
| if (dev->device == PCI_DEVICE_ID_NETMOS_9835 && |
| dev->subsystem_vendor == PCI_VENDOR_ID_IBM && |
| dev->subsystem_device == 0x0299) |
| return -ENODEV; |
| |
| if (dev->device == PCI_DEVICE_ID_NETMOS_9912) { |
| par->numports = 1; |
| } else { |
| /* |
| * Netmos uses the subdevice ID to indicate the number of parallel |
| * and serial ports. The form is 0x00PS, where <P> is the number of |
| * parallel ports and <S> is the number of serial ports. |
| */ |
| par->numports = (dev->subsystem_device & 0xf0) >> 4; |
| if (par->numports > ARRAY_SIZE(par->addr)) |
| par->numports = ARRAY_SIZE(par->addr); |
| } |
| |
| return 0; |
| } |
| |
| static struct parport_pc_pci cards[] = { |
| /* titan_110l */ { 1, { { 3, -1 }, } }, |
| /* titan_210l */ { 1, { { 3, -1 }, } }, |
| /* netmos_9xx5_combo */ { 1, { { 2, -1 }, }, netmos_parallel_init }, |
| /* netmos_9855 */ { 1, { { 0, -1 }, }, netmos_parallel_init }, |
| /* netmos_9855_2p */ { 2, { { 0, -1 }, { 2, -1 }, } }, |
| /* netmos_9900 */ {1, { { 3, 4 }, }, netmos_parallel_init }, |
| /* netmos_9900_2p */ {2, { { 0, 1 }, { 3, 4 }, } }, |
| /* netmos_99xx_1p */ {1, { { 0, 1 }, } }, |
| /* avlab_1s1p */ { 1, { { 1, 2}, } }, |
| /* avlab_1s2p */ { 2, { { 1, 2}, { 3, 4 },} }, |
| /* avlab_2s1p */ { 1, { { 2, 3}, } }, |
| /* siig_1s1p_10x */ { 1, { { 3, 4 }, } }, |
| /* siig_2s1p_10x */ { 1, { { 4, 5 }, } }, |
| /* siig_2p1s_20x */ { 2, { { 1, 2 }, { 3, 4 }, } }, |
| /* siig_1s1p_20x */ { 1, { { 1, 2 }, } }, |
| /* siig_2s1p_20x */ { 1, { { 2, 3 }, } }, |
| /* timedia_4078a */ { 1, { { 2, -1 }, } }, |
| /* timedia_4079h */ { 1, { { 2, 3 }, } }, |
| /* timedia_4085h */ { 2, { { 2, -1 }, { 4, -1 }, } }, |
| /* timedia_4088a */ { 2, { { 2, 3 }, { 4, 5 }, } }, |
| /* timedia_4089a */ { 2, { { 2, 3 }, { 4, 5 }, } }, |
| /* timedia_4095a */ { 2, { { 2, 3 }, { 4, 5 }, } }, |
| /* timedia_4096a */ { 2, { { 2, 3 }, { 4, 5 }, } }, |
| /* timedia_4078u */ { 1, { { 2, -1 }, } }, |
| /* timedia_4079a */ { 1, { { 2, 3 }, } }, |
| /* timedia_4085u */ { 2, { { 2, -1 }, { 4, -1 }, } }, |
| /* timedia_4079r */ { 1, { { 2, 3 }, } }, |
| /* timedia_4079s */ { 1, { { 2, 3 }, } }, |
| /* timedia_4079d */ { 1, { { 2, 3 }, } }, |
| /* timedia_4079e */ { 1, { { 2, 3 }, } }, |
| /* timedia_4079f */ { 1, { { 2, 3 }, } }, |
| /* timedia_9079a */ { 1, { { 2, 3 }, } }, |
| /* timedia_9079b */ { 1, { { 2, 3 }, } }, |
| /* timedia_9079c */ { 1, { { 2, 3 }, } }, |
| /* wch_ch353_1s1p*/ { 1, { { 1, -1}, } }, |
| /* wch_ch353_2s1p*/ { 1, { { 2, -1}, } }, |
| /* wch_ch382_0s1p*/ { 1, { { 2, -1}, } }, |
| /* wch_ch382_2s1p*/ { 1, { { 2, -1}, } }, |
| /* brainboxes_5s1p */ { 1, { { 3, -1 }, } }, |
| /* sunix_2s1p */ { 1, { { 3, -1 }, } }, |
| }; |
| |
| static struct pci_device_id parport_serial_pci_tbl[] = { |
| /* PCI cards */ |
| { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_110L, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_110l }, |
| { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_210L, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_210l }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9735, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9xx5_combo }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9745, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9xx5_combo }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9835, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9xx5_combo }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9845, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9xx5_combo }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9855, |
| 0x1000, 0x0020, 0, 0, netmos_9855_2p }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9855, |
| 0x1000, 0x0022, 0, 0, netmos_9855_2p }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9855, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9855 }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9900, |
| 0xA000, 0x3011, 0, 0, netmos_9900 }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9900, |
| 0xA000, 0x3012, 0, 0, netmos_9900 }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9900, |
| 0xA000, 0x3020, 0, 0, netmos_9900_2p }, |
| { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9912, |
| 0xA000, 0x2000, 0, 0, netmos_99xx_1p }, |
| /* PCI_VENDOR_ID_AVLAB/Intek21 has another bunch of cards ...*/ |
| { PCI_VENDOR_ID_AFAVLAB, 0x2110, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1s1p }, |
| { PCI_VENDOR_ID_AFAVLAB, 0x2111, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1s1p }, |
| { PCI_VENDOR_ID_AFAVLAB, 0x2112, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1s1p }, |
| { PCI_VENDOR_ID_AFAVLAB, 0x2140, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1s2p }, |
| { PCI_VENDOR_ID_AFAVLAB, 0x2141, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1s2p }, |
| { PCI_VENDOR_ID_AFAVLAB, 0x2142, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1s2p }, |
| { PCI_VENDOR_ID_AFAVLAB, 0x2160, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2s1p }, |
| { PCI_VENDOR_ID_AFAVLAB, 0x2161, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2s1p }, |
| { PCI_VENDOR_ID_AFAVLAB, 0x2162, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2s1p }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_10x_550, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1s1p_10x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_10x_650, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1s1p_10x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_10x_850, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1s1p_10x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_10x_550, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_10x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_10x_650, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_10x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_10x_850, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_10x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P1S_20x_550, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p1s_20x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P1S_20x_650, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p1s_20x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P1S_20x_850, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p1s_20x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_20x_550, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_20x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_20x_650, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1s1p_20x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_20x_850, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1s1p_20x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_20x_550, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_20x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_20x_650, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_20x }, |
| { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_20x_850, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2s1p_20x }, |
| /* PCI_VENDOR_ID_TIMEDIA/SUNIX has many differing cards ...*/ |
| { 0x1409, 0x7168, 0x1409, 0x4078, 0, 0, timedia_4078a }, |
| { 0x1409, 0x7168, 0x1409, 0x4079, 0, 0, timedia_4079h }, |
| { 0x1409, 0x7168, 0x1409, 0x4085, 0, 0, timedia_4085h }, |
| { 0x1409, 0x7168, 0x1409, 0x4088, 0, 0, timedia_4088a }, |
| { 0x1409, 0x7168, 0x1409, 0x4089, 0, 0, timedia_4089a }, |
| { 0x1409, 0x7168, 0x1409, 0x4095, 0, 0, timedia_4095a }, |
| { 0x1409, 0x7168, 0x1409, 0x4096, 0, 0, timedia_4096a }, |
| { 0x1409, 0x7168, 0x1409, 0x5078, 0, 0, timedia_4078u }, |
| { 0x1409, 0x7168, 0x1409, 0x5079, 0, 0, timedia_4079a }, |
| { 0x1409, 0x7168, 0x1409, 0x5085, 0, 0, timedia_4085u }, |
| { 0x1409, 0x7168, 0x1409, 0x6079, 0, 0, timedia_4079r }, |
| { 0x1409, 0x7168, 0x1409, 0x7079, 0, 0, timedia_4079s }, |
| { 0x1409, 0x7168, 0x1409, 0x8079, 0, 0, timedia_4079d }, |
| { 0x1409, 0x7168, 0x1409, 0x9079, 0, 0, timedia_4079e }, |
| { 0x1409, 0x7168, 0x1409, 0xa079, 0, 0, timedia_4079f }, |
| { 0x1409, 0x7168, 0x1409, 0xb079, 0, 0, timedia_9079a }, |
| { 0x1409, 0x7168, 0x1409, 0xc079, 0, 0, timedia_9079b }, |
| { 0x1409, 0x7168, 0x1409, 0xd079, 0, 0, timedia_9079c }, |
| |
| /* WCH CARDS */ |
| { 0x4348, 0x5053, PCI_ANY_ID, PCI_ANY_ID, 0, 0, wch_ch353_1s1p}, |
| { 0x4348, 0x7053, 0x4348, 0x3253, 0, 0, wch_ch353_2s1p}, |
| { 0x1c00, 0x3050, 0x1c00, 0x3050, 0, 0, wch_ch382_0s1p}, |
| { 0x1c00, 0x3250, 0x1c00, 0x3250, 0, 0, wch_ch382_2s1p}, |
| |
| /* BrainBoxes PX272/PX306 MIO card */ |
| { PCI_VENDOR_ID_INTASHIELD, 0x4100, |
| PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_5s1p }, |
| |
| /* |
| * More SUNIX variations. At least one of these has part number |
| * '5079A but subdevice 0x102. That board reports 0x0708 as |
| * its PCI Class. |
| */ |
| { PCI_VENDOR_ID_SUNIX, PCI_DEVICE_ID_SUNIX_1999, PCI_VENDOR_ID_SUNIX, |
| 0x0102, 0, 0, sunix_2s1p }, |
| |
| { 0, } /* terminate list */ |
| }; |
| MODULE_DEVICE_TABLE(pci,parport_serial_pci_tbl); |
| |
| /* |
| * This table describes the serial "geometry" of these boards. Any |
| * quirks for these can be found in drivers/serial/8250_pci.c |
| * |
| * Cards not tested are marked n/t |
| * If you have one of these cards and it works for you, please tell me.. |
| */ |
| static struct pciserial_board pci_parport_serial_boards[] = { |
| [titan_110l] = { |
| .flags = FL_BASE1 | FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [titan_210l] = { |
| .flags = FL_BASE1 | FL_BASE_BARS, |
| .num_ports = 2, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [netmos_9xx5_combo] = { |
| .flags = FL_BASE0 | FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [netmos_9855] = { |
| .flags = FL_BASE2 | FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [netmos_9855_2p] = { |
| .flags = FL_BASE4 | FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [netmos_9900] = { /* n/t */ |
| .flags = FL_BASE0 | FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [netmos_9900_2p] = { /* parallel only */ /* n/t */ |
| .flags = FL_BASE0, |
| .num_ports = 0, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [netmos_99xx_1p] = { /* parallel only */ /* n/t */ |
| .flags = FL_BASE0, |
| .num_ports = 0, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [avlab_1s1p] = { /* n/t */ |
| .flags = FL_BASE0 | FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [avlab_1s2p] = { /* n/t */ |
| .flags = FL_BASE0 | FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [avlab_2s1p] = { /* n/t */ |
| .flags = FL_BASE0 | FL_BASE_BARS, |
| .num_ports = 2, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [siig_1s1p_10x] = { |
| .flags = FL_BASE2, |
| .num_ports = 1, |
| .base_baud = 460800, |
| .uart_offset = 8, |
| }, |
| [siig_2s1p_10x] = { |
| .flags = FL_BASE2, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [siig_2p1s_20x] = { |
| .flags = FL_BASE0, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [siig_1s1p_20x] = { |
| .flags = FL_BASE0, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [siig_2s1p_20x] = { |
| .flags = FL_BASE0, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4078a] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4079h] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4085h] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4088a] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4089a] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4095a] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4096a] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4078u] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4079a] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4085u] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4079r] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4079s] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4079d] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4079e] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_4079f] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_9079a] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_9079b] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [timedia_9079c] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [wch_ch353_1s1p] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 1, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [wch_ch353_2s1p] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 2, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [wch_ch382_0s1p] = { |
| .flags = FL_BASE0, |
| .num_ports = 0, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| }, |
| [wch_ch382_2s1p] = { |
| .flags = FL_BASE0, |
| .num_ports = 2, |
| .base_baud = 115200, |
| .uart_offset = 8, |
| .first_offset = 0xC0, |
| }, |
| [brainboxes_5s1p] = { |
| .flags = FL_BASE2, |
| .num_ports = 5, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| [sunix_2s1p] = { |
| .flags = FL_BASE0|FL_BASE_BARS, |
| .num_ports = 2, |
| .base_baud = 921600, |
| .uart_offset = 8, |
| }, |
| }; |
| |
| struct parport_serial_private { |
| struct serial_private *serial; |
| int num_par; |
| struct parport *port[PARPORT_MAX]; |
| struct parport_pc_pci par; |
| }; |
| |
| /* Register the serial port(s) of a PCI card. */ |
| static int serial_register(struct pci_dev *dev, const struct pci_device_id *id) |
| { |
| struct parport_serial_private *priv = pci_get_drvdata (dev); |
| struct pciserial_board *board; |
| struct serial_private *serial; |
| |
| board = &pci_parport_serial_boards[id->driver_data]; |
| if (board->num_ports == 0) |
| return 0; |
| |
| serial = pciserial_init_ports(dev, board); |
| if (IS_ERR(serial)) |
| return PTR_ERR(serial); |
| |
| priv->serial = serial; |
| return 0; |
| } |
| |
| /* Register the parallel port(s) of a PCI card. */ |
| static int parport_register(struct pci_dev *dev, const struct pci_device_id *id) |
| { |
| struct parport_pc_pci *card; |
| struct parport_serial_private *priv = pci_get_drvdata (dev); |
| int n, success = 0; |
| |
| priv->par = cards[id->driver_data]; |
| card = &priv->par; |
| if (card->preinit_hook && |
| card->preinit_hook (dev, card, PARPORT_IRQ_NONE, PARPORT_DMA_NONE)) |
| return -ENODEV; |
| |
| for (n = 0; n < card->numports; n++) { |
| struct parport *port; |
| int lo = card->addr[n].lo; |
| int hi = card->addr[n].hi; |
| unsigned long io_lo, io_hi; |
| int irq; |
| |
| if (priv->num_par == ARRAY_SIZE (priv->port)) { |
| dev_warn(&dev->dev, |
| "only %zu parallel ports supported (%d reported)\n", |
| ARRAY_SIZE(priv->port), card->numports); |
| break; |
| } |
| |
| io_lo = pci_resource_start (dev, lo); |
| io_hi = 0; |
| if ((hi >= 0) && (hi <= 6)) |
| io_hi = pci_resource_start (dev, hi); |
| else if (hi > 6) |
| io_lo += hi; /* Reinterpret the meaning of |
| "hi" as an offset (see SYBA |
| def.) */ |
| /* TODO: test if sharing interrupts works */ |
| irq = dev->irq; |
| if (irq == IRQ_NONE) { |
| dev_dbg(&dev->dev, |
| "PCI parallel port detected: I/O at %#lx(%#lx)\n", |
| io_lo, io_hi); |
| irq = PARPORT_IRQ_NONE; |
| } else { |
| dev_dbg(&dev->dev, |
| "PCI parallel port detected: I/O at %#lx(%#lx), IRQ %d\n", |
| io_lo, io_hi, irq); |
| } |
| port = parport_pc_probe_port (io_lo, io_hi, irq, |
| PARPORT_DMA_NONE, &dev->dev, IRQF_SHARED); |
| if (port) { |
| priv->port[priv->num_par++] = port; |
| success = 1; |
| } |
| } |
| |
| if (card->postinit_hook) |
| card->postinit_hook (dev, card, !success); |
| |
| return 0; |
| } |
| |
| static int parport_serial_pci_probe(struct pci_dev *dev, |
| const struct pci_device_id *id) |
| { |
| struct parport_serial_private *priv; |
| int err; |
| |
| priv = devm_kzalloc(&dev->dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| pci_set_drvdata (dev, priv); |
| |
| err = pcim_enable_device(dev); |
| if (err) |
| return err; |
| |
| err = parport_register(dev, id); |
| if (err) |
| return err; |
| |
| err = serial_register(dev, id); |
| if (err) { |
| int i; |
| for (i = 0; i < priv->num_par; i++) |
| parport_pc_unregister_port (priv->port[i]); |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static void parport_serial_pci_remove(struct pci_dev *dev) |
| { |
| struct parport_serial_private *priv = pci_get_drvdata (dev); |
| int i; |
| |
| // Serial ports |
| if (priv->serial) |
| pciserial_remove_ports(priv->serial); |
| |
| // Parallel ports |
| for (i = 0; i < priv->num_par; i++) |
| parport_pc_unregister_port (priv->port[i]); |
| |
| return; |
| } |
| |
| static int __maybe_unused parport_serial_pci_suspend(struct device *dev) |
| { |
| struct pci_dev *pdev = to_pci_dev(dev); |
| struct parport_serial_private *priv = pci_get_drvdata(pdev); |
| |
| if (priv->serial) |
| pciserial_suspend_ports(priv->serial); |
| |
| /* FIXME: What about parport? */ |
| return 0; |
| } |
| |
| static int __maybe_unused parport_serial_pci_resume(struct device *dev) |
| { |
| struct pci_dev *pdev = to_pci_dev(dev); |
| struct parport_serial_private *priv = pci_get_drvdata(pdev); |
| |
| if (priv->serial) |
| pciserial_resume_ports(priv->serial); |
| |
| /* FIXME: What about parport? */ |
| return 0; |
| } |
| |
| static SIMPLE_DEV_PM_OPS(parport_serial_pm_ops, |
| parport_serial_pci_suspend, parport_serial_pci_resume); |
| |
| static struct pci_driver parport_serial_pci_driver = { |
| .name = "parport_serial", |
| .id_table = parport_serial_pci_tbl, |
| .probe = parport_serial_pci_probe, |
| .remove = parport_serial_pci_remove, |
| .driver = { |
| .pm = &parport_serial_pm_ops, |
| }, |
| }; |
| module_pci_driver(parport_serial_pci_driver); |
| |
| MODULE_AUTHOR("Tim Waugh <twaugh@redhat.com>"); |
| MODULE_DESCRIPTION("Driver for common parallel+serial multi-I/O PCI cards"); |
| MODULE_LICENSE("GPL"); |