| /* | |
| * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org> | |
| * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com> | |
| * Copyright (c) 2007-2008 Luis Rodriguez <mcgrof@winlab.rutgers.edu> | |
| * Copyright (c) 2007-2008 Pavel Roskin <proski@gnu.org> | |
| * Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com> | |
| * | |
| * Permission to use, copy, modify, and distribute this software for any | |
| * purpose with or without fee is hereby granted, provided that the above | |
| * copyright notice and this permission notice appear in all copies. | |
| * | |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES | |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR | |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES | |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN | |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF | |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. | |
| * | |
| */ | |
| #define _ATH5K_RESET | |
| /*****************************\ | |
| Reset functions and helpers | |
| \*****************************/ | |
| #include <linux/pci.h> /* To determine if a card is pci-e */ | |
| #include <linux/bitops.h> /* For get_bitmask_order */ | |
| #include "ath5k.h" | |
| #include "reg.h" | |
| #include "base.h" | |
| #include "debug.h" | |
| /** | |
| * ath5k_hw_write_ofdm_timings - set OFDM timings on AR5212 | |
| * | |
| * @ah: the &struct ath5k_hw | |
| * @channel: the currently set channel upon reset | |
| * | |
| * Write the delta slope coefficient (used on pilot tracking ?) for OFDM | |
| * operation on the AR5212 upon reset. This is a helper for ath5k_hw_reset(). | |
| * | |
| * Since delta slope is floating point we split it on its exponent and | |
| * mantissa and provide these values on hw. | |
| * | |
| * For more infos i think this patent is related | |
| * http://www.freepatentsonline.com/7184495.html | |
| */ | |
| static inline int ath5k_hw_write_ofdm_timings(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| /* Get exponent and mantissa and set it */ | |
| u32 coef_scaled, coef_exp, coef_man, | |
| ds_coef_exp, ds_coef_man, clock; | |
| if (!(ah->ah_version == AR5K_AR5212) || | |
| !(channel->hw_value & CHANNEL_OFDM)) | |
| BUG(); | |
| /* Get coefficient | |
| * ALGO: coef = (5 * clock * carrier_freq) / 2) | |
| * we scale coef by shifting clock value by 24 for | |
| * better precision since we use integers */ | |
| /* TODO: Half/quarter rate */ | |
| clock = ath5k_hw_htoclock(1, channel->hw_value & CHANNEL_TURBO); | |
| coef_scaled = ((5 * (clock << 24)) / 2) / channel->center_freq; | |
| /* Get exponent | |
| * ALGO: coef_exp = 14 - highest set bit position */ | |
| coef_exp = get_bitmask_order(coef_scaled); | |
| /* Doesn't make sense if it's zero*/ | |
| if (!coef_exp) | |
| return -EINVAL; | |
| /* Note: we've shifted coef_scaled by 24 */ | |
| coef_exp = 14 - (coef_exp - 24); | |
| /* Get mantissa (significant digits) | |
| * ALGO: coef_mant = floor(coef_scaled* 2^coef_exp+0.5) */ | |
| coef_man = coef_scaled + | |
| (1 << (24 - coef_exp - 1)); | |
| /* Calculate delta slope coefficient exponent | |
| * and mantissa (remove scaling) and set them on hw */ | |
| ds_coef_man = coef_man >> (24 - coef_exp); | |
| ds_coef_exp = coef_exp - 16; | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_3, | |
| AR5K_PHY_TIMING_3_DSC_MAN, ds_coef_man); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_3, | |
| AR5K_PHY_TIMING_3_DSC_EXP, ds_coef_exp); | |
| return 0; | |
| } | |
| /* | |
| * index into rates for control rates, we can set it up like this because | |
| * this is only used for AR5212 and we know it supports G mode | |
| */ | |
| static const unsigned int control_rates[] = | |
| { 0, 1, 1, 1, 4, 4, 6, 6, 8, 8, 8, 8 }; | |
| /** | |
| * ath5k_hw_write_rate_duration - fill rate code to duration table | |
| * | |
| * @ah: the &struct ath5k_hw | |
| * @mode: one of enum ath5k_driver_mode | |
| * | |
| * Write the rate code to duration table upon hw reset. This is a helper for | |
| * ath5k_hw_reset(). It seems all this is doing is setting an ACK timeout on | |
| * the hardware, based on current mode, for each rate. The rates which are | |
| * capable of short preamble (802.11b rates 2Mbps, 5.5Mbps, and 11Mbps) have | |
| * different rate code so we write their value twice (one for long preample | |
| * and one for short). | |
| * | |
| * Note: Band doesn't matter here, if we set the values for OFDM it works | |
| * on both a and g modes. So all we have to do is set values for all g rates | |
| * that include all OFDM and CCK rates. If we operate in turbo or xr/half/ | |
| * quarter rate mode, we need to use another set of bitrates (that's why we | |
| * need the mode parameter) but we don't handle these proprietary modes yet. | |
| */ | |
| static inline void ath5k_hw_write_rate_duration(struct ath5k_hw *ah, | |
| unsigned int mode) | |
| { | |
| struct ath5k_softc *sc = ah->ah_sc; | |
| struct ieee80211_rate *rate; | |
| unsigned int i; | |
| /* Write rate duration table */ | |
| for (i = 0; i < sc->sbands[IEEE80211_BAND_2GHZ].n_bitrates; i++) { | |
| u32 reg; | |
| u16 tx_time; | |
| rate = &sc->sbands[IEEE80211_BAND_2GHZ].bitrates[control_rates[i]]; | |
| /* Set ACK timeout */ | |
| reg = AR5K_RATE_DUR(rate->hw_value); | |
| /* An ACK frame consists of 10 bytes. If you add the FCS, | |
| * which ieee80211_generic_frame_duration() adds, | |
| * its 14 bytes. Note we use the control rate and not the | |
| * actual rate for this rate. See mac80211 tx.c | |
| * ieee80211_duration() for a brief description of | |
| * what rate we should choose to TX ACKs. */ | |
| tx_time = le16_to_cpu(ieee80211_generic_frame_duration(sc->hw, | |
| sc->vif, 10, rate)); | |
| ath5k_hw_reg_write(ah, tx_time, reg); | |
| if (!(rate->flags & IEEE80211_RATE_SHORT_PREAMBLE)) | |
| continue; | |
| /* | |
| * We're not distinguishing short preamble here, | |
| * This is true, all we'll get is a longer value here | |
| * which is not necessarilly bad. We could use | |
| * export ieee80211_frame_duration() but that needs to be | |
| * fixed first to be properly used by mac802111 drivers: | |
| * | |
| * - remove erp stuff and let the routine figure ofdm | |
| * erp rates | |
| * - remove passing argument ieee80211_local as | |
| * drivers don't have access to it | |
| * - move drivers using ieee80211_generic_frame_duration() | |
| * to this | |
| */ | |
| ath5k_hw_reg_write(ah, tx_time, | |
| reg + (AR5K_SET_SHORT_PREAMBLE << 2)); | |
| } | |
| } | |
| /* | |
| * Reset chipset | |
| */ | |
| static int ath5k_hw_nic_reset(struct ath5k_hw *ah, u32 val) | |
| { | |
| int ret; | |
| u32 mask = val ? val : ~0U; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Read-and-clear RX Descriptor Pointer*/ | |
| ath5k_hw_reg_read(ah, AR5K_RXDP); | |
| /* | |
| * Reset the device and wait until success | |
| */ | |
| ath5k_hw_reg_write(ah, val, AR5K_RESET_CTL); | |
| /* Wait at least 128 PCI clocks */ | |
| udelay(15); | |
| if (ah->ah_version == AR5K_AR5210) { | |
| val &= AR5K_RESET_CTL_PCU | AR5K_RESET_CTL_DMA | |
| | AR5K_RESET_CTL_MAC | AR5K_RESET_CTL_PHY; | |
| mask &= AR5K_RESET_CTL_PCU | AR5K_RESET_CTL_DMA | |
| | AR5K_RESET_CTL_MAC | AR5K_RESET_CTL_PHY; | |
| } else { | |
| val &= AR5K_RESET_CTL_PCU | AR5K_RESET_CTL_BASEBAND; | |
| mask &= AR5K_RESET_CTL_PCU | AR5K_RESET_CTL_BASEBAND; | |
| } | |
| ret = ath5k_hw_register_timeout(ah, AR5K_RESET_CTL, mask, val, false); | |
| /* | |
| * Reset configuration register (for hw byte-swap). Note that this | |
| * is only set for big endian. We do the necessary magic in | |
| * AR5K_INIT_CFG. | |
| */ | |
| if ((val & AR5K_RESET_CTL_PCU) == 0) | |
| ath5k_hw_reg_write(ah, AR5K_INIT_CFG, AR5K_CFG); | |
| return ret; | |
| } | |
| /* | |
| * Sleep control | |
| */ | |
| int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode, | |
| bool set_chip, u16 sleep_duration) | |
| { | |
| unsigned int i; | |
| u32 staid, data; | |
| ATH5K_TRACE(ah->ah_sc); | |
| staid = ath5k_hw_reg_read(ah, AR5K_STA_ID1); | |
| switch (mode) { | |
| case AR5K_PM_AUTO: | |
| staid &= ~AR5K_STA_ID1_DEFAULT_ANTENNA; | |
| /* fallthrough */ | |
| case AR5K_PM_NETWORK_SLEEP: | |
| if (set_chip) | |
| ath5k_hw_reg_write(ah, | |
| AR5K_SLEEP_CTL_SLE_ALLOW | | |
| sleep_duration, | |
| AR5K_SLEEP_CTL); | |
| staid |= AR5K_STA_ID1_PWR_SV; | |
| break; | |
| case AR5K_PM_FULL_SLEEP: | |
| if (set_chip) | |
| ath5k_hw_reg_write(ah, AR5K_SLEEP_CTL_SLE_SLP, | |
| AR5K_SLEEP_CTL); | |
| staid |= AR5K_STA_ID1_PWR_SV; | |
| break; | |
| case AR5K_PM_AWAKE: | |
| staid &= ~AR5K_STA_ID1_PWR_SV; | |
| if (!set_chip) | |
| goto commit; | |
| /* Preserve sleep duration */ | |
| data = ath5k_hw_reg_read(ah, AR5K_SLEEP_CTL); | |
| if (data & 0xffc00000) | |
| data = 0; | |
| else | |
| data = data & 0xfffcffff; | |
| ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL); | |
| udelay(15); | |
| for (i = 50; i > 0; i--) { | |
| /* Check if the chip did wake up */ | |
| if ((ath5k_hw_reg_read(ah, AR5K_PCICFG) & | |
| AR5K_PCICFG_SPWR_DN) == 0) | |
| break; | |
| /* Wait a bit and retry */ | |
| udelay(200); | |
| ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL); | |
| } | |
| /* Fail if the chip didn't wake up */ | |
| if (i <= 0) | |
| return -EIO; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| commit: | |
| ah->ah_power_mode = mode; | |
| ath5k_hw_reg_write(ah, staid, AR5K_STA_ID1); | |
| return 0; | |
| } | |
| /* | |
| * Bring up MAC + PHY Chips and program PLL | |
| * TODO: Half/Quarter rate support | |
| */ | |
| int ath5k_hw_nic_wakeup(struct ath5k_hw *ah, int flags, bool initial) | |
| { | |
| struct pci_dev *pdev = ah->ah_sc->pdev; | |
| u32 turbo, mode, clock, bus_flags; | |
| int ret; | |
| turbo = 0; | |
| mode = 0; | |
| clock = 0; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Wakeup the device */ | |
| ret = ath5k_hw_set_power(ah, AR5K_PM_AWAKE, true, 0); | |
| if (ret) { | |
| ATH5K_ERR(ah->ah_sc, "failed to wakeup the MAC Chip\n"); | |
| return ret; | |
| } | |
| if (ah->ah_version != AR5K_AR5210) { | |
| /* | |
| * Get channel mode flags | |
| */ | |
| if (ah->ah_radio >= AR5K_RF5112) { | |
| mode = AR5K_PHY_MODE_RAD_RF5112; | |
| clock = AR5K_PHY_PLL_RF5112; | |
| } else { | |
| mode = AR5K_PHY_MODE_RAD_RF5111; /*Zero*/ | |
| clock = AR5K_PHY_PLL_RF5111; /*Zero*/ | |
| } | |
| if (flags & CHANNEL_2GHZ) { | |
| mode |= AR5K_PHY_MODE_FREQ_2GHZ; | |
| clock |= AR5K_PHY_PLL_44MHZ; | |
| if (flags & CHANNEL_CCK) { | |
| mode |= AR5K_PHY_MODE_MOD_CCK; | |
| } else if (flags & CHANNEL_OFDM) { | |
| /* XXX Dynamic OFDM/CCK is not supported by the | |
| * AR5211 so we set MOD_OFDM for plain g (no | |
| * CCK headers) operation. We need to test | |
| * this, 5211 might support ofdm-only g after | |
| * all, there are also initial register values | |
| * in the code for g mode (see initvals.c). */ | |
| if (ah->ah_version == AR5K_AR5211) | |
| mode |= AR5K_PHY_MODE_MOD_OFDM; | |
| else | |
| mode |= AR5K_PHY_MODE_MOD_DYN; | |
| } else { | |
| ATH5K_ERR(ah->ah_sc, | |
| "invalid radio modulation mode\n"); | |
| return -EINVAL; | |
| } | |
| } else if (flags & CHANNEL_5GHZ) { | |
| mode |= AR5K_PHY_MODE_FREQ_5GHZ; | |
| if (ah->ah_radio == AR5K_RF5413) | |
| clock |= AR5K_PHY_PLL_40MHZ_5413; | |
| else | |
| clock |= AR5K_PHY_PLL_40MHZ; | |
| if (flags & CHANNEL_OFDM) | |
| mode |= AR5K_PHY_MODE_MOD_OFDM; | |
| else { | |
| ATH5K_ERR(ah->ah_sc, | |
| "invalid radio modulation mode\n"); | |
| return -EINVAL; | |
| } | |
| } else { | |
| ATH5K_ERR(ah->ah_sc, "invalid radio frequency mode\n"); | |
| return -EINVAL; | |
| } | |
| if (flags & CHANNEL_TURBO) | |
| turbo = AR5K_PHY_TURBO_MODE | AR5K_PHY_TURBO_SHORT; | |
| } else { /* Reset the device */ | |
| /* ...enable Atheros turbo mode if requested */ | |
| if (flags & CHANNEL_TURBO) | |
| ath5k_hw_reg_write(ah, AR5K_PHY_TURBO_MODE, | |
| AR5K_PHY_TURBO); | |
| } | |
| /* reseting PCI on PCI-E cards results card to hang | |
| * and always return 0xffff... so we ingore that flag | |
| * for PCI-E cards */ | |
| bus_flags = (pdev->is_pcie) ? 0 : AR5K_RESET_CTL_PCI; | |
| /* Reset chipset */ | |
| if (ah->ah_version == AR5K_AR5210) { | |
| ret = ath5k_hw_nic_reset(ah, AR5K_RESET_CTL_PCU | | |
| AR5K_RESET_CTL_MAC | AR5K_RESET_CTL_DMA | | |
| AR5K_RESET_CTL_PHY | AR5K_RESET_CTL_PCI); | |
| mdelay(2); | |
| } else { | |
| ret = ath5k_hw_nic_reset(ah, AR5K_RESET_CTL_PCU | | |
| AR5K_RESET_CTL_BASEBAND | bus_flags); | |
| } | |
| if (ret) { | |
| ATH5K_ERR(ah->ah_sc, "failed to reset the MAC Chip\n"); | |
| return -EIO; | |
| } | |
| /* ...wakeup again!*/ | |
| ret = ath5k_hw_set_power(ah, AR5K_PM_AWAKE, true, 0); | |
| if (ret) { | |
| ATH5K_ERR(ah->ah_sc, "failed to resume the MAC Chip\n"); | |
| return ret; | |
| } | |
| /* ...final warm reset */ | |
| if (ath5k_hw_nic_reset(ah, 0)) { | |
| ATH5K_ERR(ah->ah_sc, "failed to warm reset the MAC Chip\n"); | |
| return -EIO; | |
| } | |
| if (ah->ah_version != AR5K_AR5210) { | |
| /* ...update PLL if needed */ | |
| if (ath5k_hw_reg_read(ah, AR5K_PHY_PLL) != clock) { | |
| ath5k_hw_reg_write(ah, clock, AR5K_PHY_PLL); | |
| udelay(300); | |
| } | |
| /* ...set the PHY operating mode */ | |
| ath5k_hw_reg_write(ah, mode, AR5K_PHY_MODE); | |
| ath5k_hw_reg_write(ah, turbo, AR5K_PHY_TURBO); | |
| } | |
| return 0; | |
| } | |
| /* | |
| * If there is an external 32KHz crystal available, use it | |
| * as ref. clock instead of 32/40MHz clock and baseband clocks | |
| * to save power during sleep or restore normal 32/40MHz | |
| * operation. | |
| * | |
| * XXX: When operating on 32KHz certain PHY registers (27 - 31, | |
| * 123 - 127) require delay on access. | |
| */ | |
| static void ath5k_hw_set_sleep_clock(struct ath5k_hw *ah, bool enable) | |
| { | |
| struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; | |
| u32 scal, spending, usec32; | |
| /* Only set 32KHz settings if we have an external | |
| * 32KHz crystal present */ | |
| if ((AR5K_EEPROM_HAS32KHZCRYSTAL(ee->ee_misc1) || | |
| AR5K_EEPROM_HAS32KHZCRYSTAL_OLD(ee->ee_misc1)) && | |
| enable) { | |
| /* 1 usec/cycle */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_USEC_5211, AR5K_USEC_32, 1); | |
| /* Set up tsf increment on each cycle */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_TSF_PARM, AR5K_TSF_PARM_INC, 61); | |
| /* Set baseband sleep control registers | |
| * and sleep control rate */ | |
| ath5k_hw_reg_write(ah, 0x1f, AR5K_PHY_SCR); | |
| if ((ah->ah_radio == AR5K_RF5112) || | |
| (ah->ah_radio == AR5K_RF5413) || | |
| (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) | |
| spending = 0x14; | |
| else | |
| spending = 0x18; | |
| ath5k_hw_reg_write(ah, spending, AR5K_PHY_SPENDING); | |
| if ((ah->ah_radio == AR5K_RF5112) || | |
| (ah->ah_radio == AR5K_RF5413) || | |
| (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) { | |
| ath5k_hw_reg_write(ah, 0x26, AR5K_PHY_SLMT); | |
| ath5k_hw_reg_write(ah, 0x0d, AR5K_PHY_SCAL); | |
| ath5k_hw_reg_write(ah, 0x07, AR5K_PHY_SCLOCK); | |
| ath5k_hw_reg_write(ah, 0x3f, AR5K_PHY_SDELAY); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PCICFG, | |
| AR5K_PCICFG_SLEEP_CLOCK_RATE, 0x02); | |
| } else { | |
| ath5k_hw_reg_write(ah, 0x0a, AR5K_PHY_SLMT); | |
| ath5k_hw_reg_write(ah, 0x0c, AR5K_PHY_SCAL); | |
| ath5k_hw_reg_write(ah, 0x03, AR5K_PHY_SCLOCK); | |
| ath5k_hw_reg_write(ah, 0x20, AR5K_PHY_SDELAY); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PCICFG, | |
| AR5K_PCICFG_SLEEP_CLOCK_RATE, 0x03); | |
| } | |
| /* Enable sleep clock operation */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, | |
| AR5K_PCICFG_SLEEP_CLOCK_EN); | |
| } else { | |
| /* Disable sleep clock operation and | |
| * restore default parameters */ | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_PCICFG, | |
| AR5K_PCICFG_SLEEP_CLOCK_EN); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PCICFG, | |
| AR5K_PCICFG_SLEEP_CLOCK_RATE, 0); | |
| ath5k_hw_reg_write(ah, 0x1f, AR5K_PHY_SCR); | |
| ath5k_hw_reg_write(ah, AR5K_PHY_SLMT_32MHZ, AR5K_PHY_SLMT); | |
| if (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4)) | |
| scal = AR5K_PHY_SCAL_32MHZ_2417; | |
| else if (ath5k_eeprom_is_hb63(ah)) | |
| scal = AR5K_PHY_SCAL_32MHZ_HB63; | |
| else | |
| scal = AR5K_PHY_SCAL_32MHZ; | |
| ath5k_hw_reg_write(ah, scal, AR5K_PHY_SCAL); | |
| ath5k_hw_reg_write(ah, AR5K_PHY_SCLOCK_32MHZ, AR5K_PHY_SCLOCK); | |
| ath5k_hw_reg_write(ah, AR5K_PHY_SDELAY_32MHZ, AR5K_PHY_SDELAY); | |
| if ((ah->ah_radio == AR5K_RF5112) || | |
| (ah->ah_radio == AR5K_RF5413) || | |
| (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) | |
| spending = 0x14; | |
| else | |
| spending = 0x18; | |
| ath5k_hw_reg_write(ah, spending, AR5K_PHY_SPENDING); | |
| if ((ah->ah_radio == AR5K_RF5112) || | |
| (ah->ah_radio == AR5K_RF5413)) | |
| usec32 = 39; | |
| else | |
| usec32 = 31; | |
| AR5K_REG_WRITE_BITS(ah, AR5K_USEC_5211, AR5K_USEC_32, usec32); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_TSF_PARM, AR5K_TSF_PARM_INC, 1); | |
| } | |
| return; | |
| } | |
| static bool ath5k_hw_chan_has_spur_noise(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| u8 refclk_freq; | |
| if ((ah->ah_radio == AR5K_RF5112) || | |
| (ah->ah_radio == AR5K_RF5413) || | |
| (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) | |
| refclk_freq = 40; | |
| else | |
| refclk_freq = 32; | |
| if ((channel->center_freq % refclk_freq != 0) && | |
| ((channel->center_freq % refclk_freq < 10) || | |
| (channel->center_freq % refclk_freq > 22))) | |
| return true; | |
| else | |
| return false; | |
| } | |
| /* TODO: Half/Quarter rate */ | |
| static void ath5k_hw_tweak_initval_settings(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| if (ah->ah_version == AR5K_AR5212 && | |
| ah->ah_phy_revision >= AR5K_SREV_PHY_5212A) { | |
| /* Setup ADC control */ | |
| ath5k_hw_reg_write(ah, | |
| (AR5K_REG_SM(2, | |
| AR5K_PHY_ADC_CTL_INBUFGAIN_OFF) | | |
| AR5K_REG_SM(2, | |
| AR5K_PHY_ADC_CTL_INBUFGAIN_ON) | | |
| AR5K_PHY_ADC_CTL_PWD_DAC_OFF | | |
| AR5K_PHY_ADC_CTL_PWD_ADC_OFF), | |
| AR5K_PHY_ADC_CTL); | |
| /* Disable barker RSSI threshold */ | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_DAG_CCK_CTL, | |
| AR5K_PHY_DAG_CCK_CTL_EN_RSSI_THR); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DAG_CCK_CTL, | |
| AR5K_PHY_DAG_CCK_CTL_RSSI_THR, 2); | |
| /* Set the mute mask */ | |
| ath5k_hw_reg_write(ah, 0x0000000f, AR5K_SEQ_MASK); | |
| } | |
| /* Clear PHY_BLUETOOTH to allow RX_CLEAR line debug */ | |
| if (ah->ah_phy_revision >= AR5K_SREV_PHY_5212B) | |
| ath5k_hw_reg_write(ah, 0, AR5K_PHY_BLUETOOTH); | |
| /* Enable DCU double buffering */ | |
| if (ah->ah_phy_revision > AR5K_SREV_PHY_5212B) | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_TXCFG, | |
| AR5K_TXCFG_DCU_DBL_BUF_DIS); | |
| /* Set DAC/ADC delays */ | |
| if (ah->ah_version == AR5K_AR5212) { | |
| u32 scal; | |
| if (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4)) | |
| scal = AR5K_PHY_SCAL_32MHZ_2417; | |
| else if (ath5k_eeprom_is_hb63(ah)) | |
| scal = AR5K_PHY_SCAL_32MHZ_HB63; | |
| else | |
| scal = AR5K_PHY_SCAL_32MHZ; | |
| ath5k_hw_reg_write(ah, scal, AR5K_PHY_SCAL); | |
| } | |
| /* Set fast ADC */ | |
| if ((ah->ah_radio == AR5K_RF5413) || | |
| (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) { | |
| u32 fast_adc = true; | |
| if (channel->center_freq == 2462 || | |
| channel->center_freq == 2467) | |
| fast_adc = 0; | |
| /* Only update if needed */ | |
| if (ath5k_hw_reg_read(ah, AR5K_PHY_FAST_ADC) != fast_adc) | |
| ath5k_hw_reg_write(ah, fast_adc, | |
| AR5K_PHY_FAST_ADC); | |
| } | |
| /* Fix for first revision of the RF5112 RF chipset */ | |
| if (ah->ah_radio == AR5K_RF5112 && | |
| ah->ah_radio_5ghz_revision < | |
| AR5K_SREV_RAD_5112A) { | |
| u32 data; | |
| ath5k_hw_reg_write(ah, AR5K_PHY_CCKTXCTL_WORLD, | |
| AR5K_PHY_CCKTXCTL); | |
| if (channel->hw_value & CHANNEL_5GHZ) | |
| data = 0xffb81020; | |
| else | |
| data = 0xffb80d20; | |
| ath5k_hw_reg_write(ah, data, AR5K_PHY_FRAME_CTL); | |
| } | |
| if (ah->ah_mac_srev < AR5K_SREV_AR5211) { | |
| u32 usec_reg; | |
| /* 5311 has different tx/rx latency masks | |
| * from 5211, since we deal 5311 the same | |
| * as 5211 when setting initvals, shift | |
| * values here to their proper locations */ | |
| usec_reg = ath5k_hw_reg_read(ah, AR5K_USEC_5211); | |
| ath5k_hw_reg_write(ah, usec_reg & (AR5K_USEC_1 | | |
| AR5K_USEC_32 | | |
| AR5K_USEC_TX_LATENCY_5211 | | |
| AR5K_REG_SM(29, | |
| AR5K_USEC_RX_LATENCY_5210)), | |
| AR5K_USEC_5211); | |
| /* Clear QCU/DCU clock gating register */ | |
| ath5k_hw_reg_write(ah, 0, AR5K_QCUDCU_CLKGT); | |
| /* Set DAC/ADC delays */ | |
| ath5k_hw_reg_write(ah, 0x08, AR5K_PHY_SCAL); | |
| /* Enable PCU FIFO corruption ECO */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5211, | |
| AR5K_DIAG_SW_ECO_ENABLE); | |
| } | |
| } | |
| static void ath5k_hw_commit_eeprom_settings(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel, u8 *ant, u8 ee_mode) | |
| { | |
| struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; | |
| s16 cck_ofdm_pwr_delta; | |
| /* Adjust power delta for channel 14 */ | |
| if (channel->center_freq == 2484) | |
| cck_ofdm_pwr_delta = | |
| ((ee->ee_cck_ofdm_power_delta - | |
| ee->ee_scaled_cck_delta) * 2) / 10; | |
| else | |
| cck_ofdm_pwr_delta = | |
| (ee->ee_cck_ofdm_power_delta * 2) / 10; | |
| /* Set CCK to OFDM power delta on tx power | |
| * adjustment register */ | |
| if (ah->ah_phy_revision >= AR5K_SREV_PHY_5212A) { | |
| if (channel->hw_value == CHANNEL_G) | |
| ath5k_hw_reg_write(ah, | |
| AR5K_REG_SM((ee->ee_cck_ofdm_gain_delta * -1), | |
| AR5K_PHY_TX_PWR_ADJ_CCK_GAIN_DELTA) | | |
| AR5K_REG_SM((cck_ofdm_pwr_delta * -1), | |
| AR5K_PHY_TX_PWR_ADJ_CCK_PCDAC_INDEX), | |
| AR5K_PHY_TX_PWR_ADJ); | |
| else | |
| ath5k_hw_reg_write(ah, 0, AR5K_PHY_TX_PWR_ADJ); | |
| } else { | |
| /* For older revs we scale power on sw during tx power | |
| * setup */ | |
| ah->ah_txpower.txp_cck_ofdm_pwr_delta = cck_ofdm_pwr_delta; | |
| ah->ah_txpower.txp_cck_ofdm_gainf_delta = | |
| ee->ee_cck_ofdm_gain_delta; | |
| } | |
| /* Set antenna idle switch table */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_ANT_CTL, | |
| AR5K_PHY_ANT_CTL_SWTABLE_IDLE, | |
| (ah->ah_antenna[ee_mode][0] | | |
| AR5K_PHY_ANT_CTL_TXRX_EN)); | |
| /* Set antenna switch table */ | |
| ath5k_hw_reg_write(ah, ah->ah_antenna[ee_mode][ant[0]], | |
| AR5K_PHY_ANT_SWITCH_TABLE_0); | |
| ath5k_hw_reg_write(ah, ah->ah_antenna[ee_mode][ant[1]], | |
| AR5K_PHY_ANT_SWITCH_TABLE_1); | |
| /* Noise floor threshold */ | |
| ath5k_hw_reg_write(ah, | |
| AR5K_PHY_NF_SVAL(ee->ee_noise_floor_thr[ee_mode]), | |
| AR5K_PHY_NFTHRES); | |
| if ((channel->hw_value & CHANNEL_TURBO) && | |
| (ah->ah_ee_version >= AR5K_EEPROM_VERSION_5_0)) { | |
| /* Switch settling time (Turbo) */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_SETTLING, | |
| AR5K_PHY_SETTLING_SWITCH, | |
| ee->ee_switch_settling_turbo[ee_mode]); | |
| /* Tx/Rx attenuation (Turbo) */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN, | |
| AR5K_PHY_GAIN_TXRX_ATTEN, | |
| ee->ee_atn_tx_rx_turbo[ee_mode]); | |
| /* ADC/PGA desired size (Turbo) */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE, | |
| AR5K_PHY_DESIRED_SIZE_ADC, | |
| ee->ee_adc_desired_size_turbo[ee_mode]); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE, | |
| AR5K_PHY_DESIRED_SIZE_PGA, | |
| ee->ee_pga_desired_size_turbo[ee_mode]); | |
| /* Tx/Rx margin (Turbo) */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN_2GHZ, | |
| AR5K_PHY_GAIN_2GHZ_MARGIN_TXRX, | |
| ee->ee_margin_tx_rx_turbo[ee_mode]); | |
| } else { | |
| /* Switch settling time */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_SETTLING, | |
| AR5K_PHY_SETTLING_SWITCH, | |
| ee->ee_switch_settling[ee_mode]); | |
| /* Tx/Rx attenuation */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN, | |
| AR5K_PHY_GAIN_TXRX_ATTEN, | |
| ee->ee_atn_tx_rx[ee_mode]); | |
| /* ADC/PGA desired size */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE, | |
| AR5K_PHY_DESIRED_SIZE_ADC, | |
| ee->ee_adc_desired_size[ee_mode]); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE, | |
| AR5K_PHY_DESIRED_SIZE_PGA, | |
| ee->ee_pga_desired_size[ee_mode]); | |
| /* Tx/Rx margin */ | |
| if (ah->ah_ee_version >= AR5K_EEPROM_VERSION_4_1) | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN_2GHZ, | |
| AR5K_PHY_GAIN_2GHZ_MARGIN_TXRX, | |
| ee->ee_margin_tx_rx[ee_mode]); | |
| } | |
| /* XPA delays */ | |
| ath5k_hw_reg_write(ah, | |
| (ee->ee_tx_end2xpa_disable[ee_mode] << 24) | | |
| (ee->ee_tx_end2xpa_disable[ee_mode] << 16) | | |
| (ee->ee_tx_frm2xpa_enable[ee_mode] << 8) | | |
| (ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY_RF_CTL4); | |
| /* XLNA delay */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_RF_CTL3, | |
| AR5K_PHY_RF_CTL3_TXE2XLNA_ON, | |
| ee->ee_tx_end2xlna_enable[ee_mode]); | |
| /* Thresh64 (ANI) */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_NF, | |
| AR5K_PHY_NF_THRESH62, | |
| ee->ee_thr_62[ee_mode]); | |
| /* False detect backoff for channels | |
| * that have spur noise. Write the new | |
| * cyclic power RSSI threshold. */ | |
| if (ath5k_hw_chan_has_spur_noise(ah, channel)) | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_OFDM_SELFCORR, | |
| AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1, | |
| AR5K_INIT_CYCRSSI_THR1 + | |
| ee->ee_false_detect[ee_mode]); | |
| else | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_OFDM_SELFCORR, | |
| AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1, | |
| AR5K_INIT_CYCRSSI_THR1); | |
| /* I/Q correction | |
| * TODO: Per channel i/q infos ? */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, | |
| AR5K_PHY_IQ_CORR_ENABLE | | |
| (ee->ee_i_cal[ee_mode] << AR5K_PHY_IQ_CORR_Q_I_COFF_S) | | |
| ee->ee_q_cal[ee_mode]); | |
| /* Heavy clipping -disable for now */ | |
| if (ah->ah_ee_version >= AR5K_EEPROM_VERSION_5_1) | |
| ath5k_hw_reg_write(ah, 0, AR5K_PHY_HEAVY_CLIP_ENABLE); | |
| return; | |
| } | |
| /* | |
| * Main reset function | |
| */ | |
| int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, | |
| struct ieee80211_channel *channel, bool change_channel) | |
| { | |
| u32 s_seq[10], s_ant, s_led[3], staid1_flags, tsf_up, tsf_lo; | |
| u32 phy_tst1; | |
| u8 mode, freq, ee_mode, ant[2]; | |
| int i, ret; | |
| ATH5K_TRACE(ah->ah_sc); | |
| s_ant = 0; | |
| ee_mode = 0; | |
| staid1_flags = 0; | |
| tsf_up = 0; | |
| tsf_lo = 0; | |
| freq = 0; | |
| mode = 0; | |
| /* | |
| * Save some registers before a reset | |
| */ | |
| /*DCU/Antenna selection not available on 5210*/ | |
| if (ah->ah_version != AR5K_AR5210) { | |
| switch (channel->hw_value & CHANNEL_MODES) { | |
| case CHANNEL_A: | |
| mode = AR5K_MODE_11A; | |
| freq = AR5K_INI_RFGAIN_5GHZ; | |
| ee_mode = AR5K_EEPROM_MODE_11A; | |
| break; | |
| case CHANNEL_G: | |
| mode = AR5K_MODE_11G; | |
| freq = AR5K_INI_RFGAIN_2GHZ; | |
| ee_mode = AR5K_EEPROM_MODE_11G; | |
| break; | |
| case CHANNEL_B: | |
| mode = AR5K_MODE_11B; | |
| freq = AR5K_INI_RFGAIN_2GHZ; | |
| ee_mode = AR5K_EEPROM_MODE_11B; | |
| break; | |
| case CHANNEL_T: | |
| mode = AR5K_MODE_11A_TURBO; | |
| freq = AR5K_INI_RFGAIN_5GHZ; | |
| ee_mode = AR5K_EEPROM_MODE_11A; | |
| break; | |
| case CHANNEL_TG: | |
| if (ah->ah_version == AR5K_AR5211) { | |
| ATH5K_ERR(ah->ah_sc, | |
| "TurboG mode not available on 5211"); | |
| return -EINVAL; | |
| } | |
| mode = AR5K_MODE_11G_TURBO; | |
| freq = AR5K_INI_RFGAIN_2GHZ; | |
| ee_mode = AR5K_EEPROM_MODE_11G; | |
| break; | |
| case CHANNEL_XR: | |
| if (ah->ah_version == AR5K_AR5211) { | |
| ATH5K_ERR(ah->ah_sc, | |
| "XR mode not available on 5211"); | |
| return -EINVAL; | |
| } | |
| mode = AR5K_MODE_XR; | |
| freq = AR5K_INI_RFGAIN_5GHZ; | |
| ee_mode = AR5K_EEPROM_MODE_11A; | |
| break; | |
| default: | |
| ATH5K_ERR(ah->ah_sc, | |
| "invalid channel: %d\n", channel->center_freq); | |
| return -EINVAL; | |
| } | |
| if (change_channel) { | |
| /* | |
| * Save frame sequence count | |
| * For revs. after Oahu, only save | |
| * seq num for DCU 0 (Global seq num) | |
| */ | |
| if (ah->ah_mac_srev < AR5K_SREV_AR5211) { | |
| for (i = 0; i < 10; i++) | |
| s_seq[i] = ath5k_hw_reg_read(ah, | |
| AR5K_QUEUE_DCU_SEQNUM(i)); | |
| } else { | |
| s_seq[0] = ath5k_hw_reg_read(ah, | |
| AR5K_QUEUE_DCU_SEQNUM(0)); | |
| } | |
| /* TSF accelerates on AR5211 durring reset | |
| * As a workaround save it here and restore | |
| * it later so that it's back in time after | |
| * reset. This way it'll get re-synced on the | |
| * next beacon without breaking ad-hoc. | |
| * | |
| * On AR5212 TSF is almost preserved across a | |
| * reset so it stays back in time anyway and | |
| * we don't have to save/restore it. | |
| * | |
| * XXX: Since this breaks power saving we have | |
| * to disable power saving until we receive the | |
| * next beacon, so we can resync beacon timers */ | |
| if (ah->ah_version == AR5K_AR5211) { | |
| tsf_up = ath5k_hw_reg_read(ah, AR5K_TSF_U32); | |
| tsf_lo = ath5k_hw_reg_read(ah, AR5K_TSF_L32); | |
| } | |
| } | |
| /* Save default antenna */ | |
| s_ant = ath5k_hw_reg_read(ah, AR5K_DEFAULT_ANTENNA); | |
| if (ah->ah_version == AR5K_AR5212) { | |
| /* Restore normal 32/40MHz clock operation | |
| * to avoid register access delay on certain | |
| * PHY registers */ | |
| ath5k_hw_set_sleep_clock(ah, false); | |
| /* Since we are going to write rf buffer | |
| * check if we have any pending gain_F | |
| * optimization settings */ | |
| if (change_channel && ah->ah_rf_banks != NULL) | |
| ath5k_hw_gainf_calibrate(ah); | |
| } | |
| } | |
| /*GPIOs*/ | |
| s_led[0] = ath5k_hw_reg_read(ah, AR5K_PCICFG) & | |
| AR5K_PCICFG_LEDSTATE; | |
| s_led[1] = ath5k_hw_reg_read(ah, AR5K_GPIOCR); | |
| s_led[2] = ath5k_hw_reg_read(ah, AR5K_GPIODO); | |
| /* AR5K_STA_ID1 flags, only preserve antenna | |
| * settings and ack/cts rate mode */ | |
| staid1_flags = ath5k_hw_reg_read(ah, AR5K_STA_ID1) & | |
| (AR5K_STA_ID1_DEFAULT_ANTENNA | | |
| AR5K_STA_ID1_DESC_ANTENNA | | |
| AR5K_STA_ID1_RTS_DEF_ANTENNA | | |
| AR5K_STA_ID1_ACKCTS_6MB | | |
| AR5K_STA_ID1_BASE_RATE_11B | | |
| AR5K_STA_ID1_SELFGEN_DEF_ANT); | |
| /* Wakeup the device */ | |
| ret = ath5k_hw_nic_wakeup(ah, channel->hw_value, false); | |
| if (ret) | |
| return ret; | |
| /* | |
| * Initialize operating mode | |
| */ | |
| ah->ah_op_mode = op_mode; | |
| /* PHY access enable */ | |
| if (ah->ah_mac_srev >= AR5K_SREV_AR5211) | |
| ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); | |
| else | |
| ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ | 0x40, | |
| AR5K_PHY(0)); | |
| /* Write initial settings */ | |
| ret = ath5k_hw_write_initvals(ah, mode, change_channel); | |
| if (ret) | |
| return ret; | |
| /* | |
| * 5211/5212 Specific | |
| */ | |
| if (ah->ah_version != AR5K_AR5210) { | |
| /* | |
| * Write initial RF gain settings | |
| * This should work for both 5111/5112 | |
| */ | |
| ret = ath5k_hw_rfgain_init(ah, freq); | |
| if (ret) | |
| return ret; | |
| mdelay(1); | |
| /* | |
| * Tweak initval settings for revised | |
| * chipsets and add some more config | |
| * bits | |
| */ | |
| ath5k_hw_tweak_initval_settings(ah, channel); | |
| /* | |
| * Set TX power (FIXME) | |
| */ | |
| ret = ath5k_hw_txpower(ah, channel, ee_mode, | |
| AR5K_TUNE_DEFAULT_TXPOWER); | |
| if (ret) | |
| return ret; | |
| /* Write rate duration table only on AR5212 and if | |
| * virtual interface has already been brought up | |
| * XXX: rethink this after new mode changes to | |
| * mac80211 are integrated */ | |
| if (ah->ah_version == AR5K_AR5212 && | |
| ah->ah_sc->vif != NULL) | |
| ath5k_hw_write_rate_duration(ah, mode); | |
| /* | |
| * Write RF buffer | |
| */ | |
| ret = ath5k_hw_rfregs_init(ah, channel, mode); | |
| if (ret) | |
| return ret; | |
| /* Write OFDM timings on 5212*/ | |
| if (ah->ah_version == AR5K_AR5212 && | |
| channel->hw_value & CHANNEL_OFDM) { | |
| ret = ath5k_hw_write_ofdm_timings(ah, channel); | |
| if (ret) | |
| return ret; | |
| } | |
| /*Enable/disable 802.11b mode on 5111 | |
| (enable 2111 frequency converter + CCK)*/ | |
| if (ah->ah_radio == AR5K_RF5111) { | |
| if (mode == AR5K_MODE_11B) | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_TXCFG, | |
| AR5K_TXCFG_B_MODE); | |
| else | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_TXCFG, | |
| AR5K_TXCFG_B_MODE); | |
| } | |
| /* | |
| * In case a fixed antenna was set as default | |
| * write the same settings on both AR5K_PHY_ANT_SWITCH_TABLE | |
| * registers. | |
| */ | |
| if (s_ant != 0) { | |
| if (s_ant == AR5K_ANT_FIXED_A) /* 1 - Main */ | |
| ant[0] = ant[1] = AR5K_ANT_FIXED_A; | |
| else /* 2 - Aux */ | |
| ant[0] = ant[1] = AR5K_ANT_FIXED_B; | |
| } else { | |
| ant[0] = AR5K_ANT_FIXED_A; | |
| ant[1] = AR5K_ANT_FIXED_B; | |
| } | |
| /* Commit values from EEPROM */ | |
| ath5k_hw_commit_eeprom_settings(ah, channel, ant, ee_mode); | |
| } else { | |
| /* | |
| * For 5210 we do all initialization using | |
| * initvals, so we don't have to modify | |
| * any settings (5210 also only supports | |
| * a/aturbo modes) | |
| */ | |
| mdelay(1); | |
| /* Disable phy and wait */ | |
| ath5k_hw_reg_write(ah, AR5K_PHY_ACT_DISABLE, AR5K_PHY_ACT); | |
| mdelay(1); | |
| } | |
| /* | |
| * Restore saved values | |
| */ | |
| /*DCU/Antenna selection not available on 5210*/ | |
| if (ah->ah_version != AR5K_AR5210) { | |
| if (change_channel) { | |
| if (ah->ah_mac_srev < AR5K_SREV_AR5211) { | |
| for (i = 0; i < 10; i++) | |
| ath5k_hw_reg_write(ah, s_seq[i], | |
| AR5K_QUEUE_DCU_SEQNUM(i)); | |
| } else { | |
| ath5k_hw_reg_write(ah, s_seq[0], | |
| AR5K_QUEUE_DCU_SEQNUM(0)); | |
| } | |
| if (ah->ah_version == AR5K_AR5211) { | |
| ath5k_hw_reg_write(ah, tsf_up, AR5K_TSF_U32); | |
| ath5k_hw_reg_write(ah, tsf_lo, AR5K_TSF_L32); | |
| } | |
| } | |
| ath5k_hw_reg_write(ah, s_ant, AR5K_DEFAULT_ANTENNA); | |
| } | |
| /* Ledstate */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, s_led[0]); | |
| /* Gpio settings */ | |
| ath5k_hw_reg_write(ah, s_led[1], AR5K_GPIOCR); | |
| ath5k_hw_reg_write(ah, s_led[2], AR5K_GPIODO); | |
| /* Restore sta_id flags and preserve our mac address*/ | |
| ath5k_hw_reg_write(ah, AR5K_LOW_ID(ah->ah_sta_id), | |
| AR5K_STA_ID0); | |
| ath5k_hw_reg_write(ah, staid1_flags | AR5K_HIGH_ID(ah->ah_sta_id), | |
| AR5K_STA_ID1); | |
| /* | |
| * Configure PCU | |
| */ | |
| /* Restore bssid and bssid mask */ | |
| /* XXX: add ah->aid once mac80211 gives this to us */ | |
| ath5k_hw_set_associd(ah, ah->ah_bssid, 0); | |
| /* Set PCU config */ | |
| ath5k_hw_set_opmode(ah); | |
| /* Clear any pending interrupts | |
| * PISR/SISR Not available on 5210 */ | |
| if (ah->ah_version != AR5K_AR5210) | |
| ath5k_hw_reg_write(ah, 0xffffffff, AR5K_PISR); | |
| /* Set RSSI/BRSSI thresholds | |
| * | |
| * Note: If we decide to set this value | |
| * dynamicaly, have in mind that when AR5K_RSSI_THR | |
| * register is read it might return 0x40 if we haven't | |
| * wrote anything to it plus BMISS RSSI threshold is zeroed. | |
| * So doing a save/restore procedure here isn't the right | |
| * choice. Instead store it on ath5k_hw */ | |
| ath5k_hw_reg_write(ah, (AR5K_TUNE_RSSI_THRES | | |
| AR5K_TUNE_BMISS_THRES << | |
| AR5K_RSSI_THR_BMISS_S), | |
| AR5K_RSSI_THR); | |
| /* MIC QoS support */ | |
| if (ah->ah_mac_srev >= AR5K_SREV_AR2413) { | |
| ath5k_hw_reg_write(ah, 0x000100aa, AR5K_MIC_QOS_CTL); | |
| ath5k_hw_reg_write(ah, 0x00003210, AR5K_MIC_QOS_SEL); | |
| } | |
| /* QoS NOACK Policy */ | |
| if (ah->ah_version == AR5K_AR5212) { | |
| ath5k_hw_reg_write(ah, | |
| AR5K_REG_SM(2, AR5K_QOS_NOACK_2BIT_VALUES) | | |
| AR5K_REG_SM(5, AR5K_QOS_NOACK_BIT_OFFSET) | | |
| AR5K_REG_SM(0, AR5K_QOS_NOACK_BYTE_OFFSET), | |
| AR5K_QOS_NOACK); | |
| } | |
| /* | |
| * Configure PHY | |
| */ | |
| /* Set channel on PHY */ | |
| ret = ath5k_hw_channel(ah, channel); | |
| if (ret) | |
| return ret; | |
| /* | |
| * Enable the PHY and wait until completion | |
| * This includes BaseBand and Synthesizer | |
| * activation. | |
| */ | |
| ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT); | |
| /* | |
| * On 5211+ read activation -> rx delay | |
| * and use it. | |
| * | |
| * TODO: Half/quarter rate support | |
| */ | |
| if (ah->ah_version != AR5K_AR5210) { | |
| u32 delay; | |
| delay = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) & | |
| AR5K_PHY_RX_DELAY_M; | |
| delay = (channel->hw_value & CHANNEL_CCK) ? | |
| ((delay << 2) / 22) : (delay / 10); | |
| udelay(100 + (2 * delay)); | |
| } else { | |
| mdelay(1); | |
| } | |
| /* | |
| * Perform ADC test to see if baseband is ready | |
| * Set tx hold and check adc test register | |
| */ | |
| phy_tst1 = ath5k_hw_reg_read(ah, AR5K_PHY_TST1); | |
| ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1); | |
| for (i = 0; i <= 20; i++) { | |
| if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10)) | |
| break; | |
| udelay(200); | |
| } | |
| ath5k_hw_reg_write(ah, phy_tst1, AR5K_PHY_TST1); | |
| /* | |
| * Start automatic gain control calibration | |
| * | |
| * During AGC calibration RX path is re-routed to | |
| * a power detector so we don't receive anything. | |
| * | |
| * This method is used to calibrate some static offsets | |
| * used together with on-the fly I/Q calibration (the | |
| * one performed via ath5k_hw_phy_calibrate), that doesn't | |
| * interrupt rx path. | |
| * | |
| * While rx path is re-routed to the power detector we also | |
| * start a noise floor calibration, to measure the | |
| * card's noise floor (the noise we measure when we are not | |
| * transmiting or receiving anything). | |
| * | |
| * If we are in a noisy environment AGC calibration may time | |
| * out and/or noise floor calibration might timeout. | |
| */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, | |
| AR5K_PHY_AGCCTL_CAL); | |
| /* At the same time start I/Q calibration for QAM constellation | |
| * -no need for CCK- */ | |
| ah->ah_calibration = false; | |
| if (!(mode == AR5K_MODE_11B)) { | |
| ah->ah_calibration = true; | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, | |
| AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, | |
| AR5K_PHY_IQ_RUN); | |
| } | |
| /* Wait for gain calibration to finish (we check for I/Q calibration | |
| * during ath5k_phy_calibrate) */ | |
| if (ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, | |
| AR5K_PHY_AGCCTL_CAL, 0, false)) { | |
| ATH5K_ERR(ah->ah_sc, "gain calibration timeout (%uMHz)\n", | |
| channel->center_freq); | |
| } | |
| /* | |
| * If we run NF calibration before AGC, it always times out. | |
| * Binary HAL starts NF and AGC calibration at the same time | |
| * and only waits for AGC to finish. Also if AGC or NF cal. | |
| * times out, reset doesn't fail on binary HAL. I believe | |
| * that's wrong because since rx path is routed to a detector, | |
| * if cal. doesn't finish we won't have RX. Sam's HAL for AR5210/5211 | |
| * enables noise floor calibration after offset calibration and if noise | |
| * floor calibration fails, reset fails. I believe that's | |
| * a better approach, we just need to find a polling interval | |
| * that suits best, even if reset continues we need to make | |
| * sure that rx path is ready. | |
| */ | |
| ath5k_hw_noise_floor_calibration(ah, channel->center_freq); | |
| /* | |
| * Configure QCUs/DCUs | |
| */ | |
| /* TODO: HW Compression support for data queues */ | |
| /* TODO: Burst prefetch for data queues */ | |
| /* | |
| * Reset queues and start beacon timers at the end of the reset routine | |
| * This also sets QCU mask on each DCU for 1:1 qcu to dcu mapping | |
| * Note: If we want we can assign multiple qcus on one dcu. | |
| */ | |
| for (i = 0; i < ah->ah_capabilities.cap_queues.q_tx_num; i++) { | |
| ret = ath5k_hw_reset_tx_queue(ah, i); | |
| if (ret) { | |
| ATH5K_ERR(ah->ah_sc, | |
| "failed to reset TX queue #%d\n", i); | |
| return ret; | |
| } | |
| } | |
| /* | |
| * Configure DMA/Interrupts | |
| */ | |
| /* | |
| * Set Rx/Tx DMA Configuration | |
| * | |
| * Set standard DMA size (128). Note that | |
| * a DMA size of 512 causes rx overruns and tx errors | |
| * on pci-e cards (tested on 5424 but since rx overruns | |
| * also occur on 5416/5418 with madwifi we set 128 | |
| * for all PCI-E cards to be safe). | |
| * | |
| * XXX: need to check 5210 for this | |
| * TODO: Check out tx triger level, it's always 64 on dumps but I | |
| * guess we can tweak it and see how it goes ;-) | |
| */ | |
| if (ah->ah_version != AR5K_AR5210) { | |
| AR5K_REG_WRITE_BITS(ah, AR5K_TXCFG, | |
| AR5K_TXCFG_SDMAMR, AR5K_DMASIZE_128B); | |
| AR5K_REG_WRITE_BITS(ah, AR5K_RXCFG, | |
| AR5K_RXCFG_SDMAMW, AR5K_DMASIZE_128B); | |
| } | |
| /* Pre-enable interrupts on 5211/5212*/ | |
| if (ah->ah_version != AR5K_AR5210) | |
| ath5k_hw_set_imr(ah, ah->ah_imr); | |
| /* | |
| * Setup RFKill interrupt if rfkill flag is set on eeprom. | |
| * TODO: Use gpio pin and polarity infos from eeprom | |
| * TODO: Handle this in ath5k_intr because it'll result | |
| * a nasty interrupt storm. | |
| */ | |
| #if 0 | |
| if (AR5K_EEPROM_HDR_RFKILL(ah->ah_capabilities.cap_eeprom.ee_header)) { | |
| ath5k_hw_set_gpio_input(ah, 0); | |
| ah->ah_gpio[0] = ath5k_hw_get_gpio(ah, 0); | |
| if (ah->ah_gpio[0] == 0) | |
| ath5k_hw_set_gpio_intr(ah, 0, 1); | |
| else | |
| ath5k_hw_set_gpio_intr(ah, 0, 0); | |
| } | |
| #endif | |
| /* Enable 32KHz clock function for AR5212+ chips | |
| * Set clocks to 32KHz operation and use an | |
| * external 32KHz crystal when sleeping if one | |
| * exists */ | |
| if (ah->ah_version == AR5K_AR5212) | |
| ath5k_hw_set_sleep_clock(ah, true); | |
| /* | |
| * Disable beacons and reset the register | |
| */ | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_BEACON, AR5K_BEACON_ENABLE | | |
| AR5K_BEACON_RESET_TSF); | |
| return 0; | |
| } | |
| #undef _ATH5K_RESET |