| /* | |
| * PHY functions | |
| * | |
| * Copyright (c) 2004-2007 Reyk Floeter <reyk@openbsd.org> | |
| * Copyright (c) 2006-2009 Nick Kossifidis <mickflemm@gmail.com> | |
| * Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com> | |
| * Copyright (c) 2008-2009 Felix Fietkau <nbd@openwrt.org> | |
| * | |
| * Permission to use, copy, modify, and distribute this software for any | |
| * purpose with or without fee is hereby granted, provided that the above | |
| * copyright notice and this permission notice appear in all copies. | |
| * | |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES | |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR | |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES | |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN | |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF | |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. | |
| * | |
| */ | |
| #define _ATH5K_PHY | |
| #include <linux/delay.h> | |
| #include "ath5k.h" | |
| #include "reg.h" | |
| #include "base.h" | |
| #include "rfbuffer.h" | |
| #include "rfgain.h" | |
| /* | |
| * Used to modify RF Banks before writing them to AR5K_RF_BUFFER | |
| */ | |
| static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah, | |
| const struct ath5k_rf_reg *rf_regs, | |
| u32 val, u8 reg_id, bool set) | |
| { | |
| const struct ath5k_rf_reg *rfreg = NULL; | |
| u8 offset, bank, num_bits, col, position; | |
| u16 entry; | |
| u32 mask, data, last_bit, bits_shifted, first_bit; | |
| u32 *rfb; | |
| s32 bits_left; | |
| int i; | |
| data = 0; | |
| rfb = ah->ah_rf_banks; | |
| for (i = 0; i < ah->ah_rf_regs_count; i++) { | |
| if (rf_regs[i].index == reg_id) { | |
| rfreg = &rf_regs[i]; | |
| break; | |
| } | |
| } | |
| if (rfb == NULL || rfreg == NULL) { | |
| ATH5K_PRINTF("Rf register not found!\n"); | |
| /* should not happen */ | |
| return 0; | |
| } | |
| bank = rfreg->bank; | |
| num_bits = rfreg->field.len; | |
| first_bit = rfreg->field.pos; | |
| col = rfreg->field.col; | |
| /* first_bit is an offset from bank's | |
| * start. Since we have all banks on | |
| * the same array, we use this offset | |
| * to mark each bank's start */ | |
| offset = ah->ah_offset[bank]; | |
| /* Boundary check */ | |
| if (!(col <= 3 && num_bits <= 32 && first_bit + num_bits <= 319)) { | |
| ATH5K_PRINTF("invalid values at offset %u\n", offset); | |
| return 0; | |
| } | |
| entry = ((first_bit - 1) / 8) + offset; | |
| position = (first_bit - 1) % 8; | |
| if (set) | |
| data = ath5k_hw_bitswap(val, num_bits); | |
| for (bits_shifted = 0, bits_left = num_bits; bits_left > 0; | |
| position = 0, entry++) { | |
| last_bit = (position + bits_left > 8) ? 8 : | |
| position + bits_left; | |
| mask = (((1 << last_bit) - 1) ^ ((1 << position) - 1)) << | |
| (col * 8); | |
| if (set) { | |
| rfb[entry] &= ~mask; | |
| rfb[entry] |= ((data << position) << (col * 8)) & mask; | |
| data >>= (8 - position); | |
| } else { | |
| data |= (((rfb[entry] & mask) >> (col * 8)) >> position) | |
| << bits_shifted; | |
| bits_shifted += last_bit - position; | |
| } | |
| bits_left -= 8 - position; | |
| } | |
| data = set ? 1 : ath5k_hw_bitswap(data, num_bits); | |
| return data; | |
| } | |
| /**********************\ | |
| * RF Gain optimization * | |
| \**********************/ | |
| /* | |
| * This code is used to optimize rf gain on different environments | |
| * (temprature mostly) based on feedback from a power detector. | |
| * | |
| * It's only used on RF5111 and RF5112, later RF chips seem to have | |
| * auto adjustment on hw -notice they have a much smaller BANK 7 and | |
| * no gain optimization ladder-. | |
| * | |
| * For more infos check out this patent doc | |
| * http://www.freepatentsonline.com/7400691.html | |
| * | |
| * This paper describes power drops as seen on the receiver due to | |
| * probe packets | |
| * http://www.cnri.dit.ie/publications/ICT08%20-%20Practical%20Issues | |
| * %20of%20Power%20Control.pdf | |
| * | |
| * And this is the MadWiFi bug entry related to the above | |
| * http://madwifi-project.org/ticket/1659 | |
| * with various measurements and diagrams | |
| * | |
| * TODO: Deal with power drops due to probes by setting an apropriate | |
| * tx power on the probe packets ! Make this part of the calibration process. | |
| */ | |
| /* Initialize ah_gain durring attach */ | |
| int ath5k_hw_rfgain_opt_init(struct ath5k_hw *ah) | |
| { | |
| /* Initialize the gain optimization values */ | |
| switch (ah->ah_radio) { | |
| case AR5K_RF5111: | |
| ah->ah_gain.g_step_idx = rfgain_opt_5111.go_default; | |
| ah->ah_gain.g_low = 20; | |
| ah->ah_gain.g_high = 35; | |
| ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; | |
| break; | |
| case AR5K_RF5112: | |
| ah->ah_gain.g_step_idx = rfgain_opt_5112.go_default; | |
| ah->ah_gain.g_low = 20; | |
| ah->ah_gain.g_high = 85; | |
| ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| /* Schedule a gain probe check on the next transmited packet. | |
| * That means our next packet is going to be sent with lower | |
| * tx power and a Peak to Average Power Detector (PAPD) will try | |
| * to measure the gain. | |
| * | |
| * TODO: Use propper tx power setting for the probe packet so | |
| * that we don't observe a serious power drop on the receiver | |
| * | |
| * XXX: How about forcing a tx packet (bypassing PCU arbitrator etc) | |
| * just after we enable the probe so that we don't mess with | |
| * standard traffic ? Maybe it's time to use sw interrupts and | |
| * a probe tasklet !!! | |
| */ | |
| static void ath5k_hw_request_rfgain_probe(struct ath5k_hw *ah) | |
| { | |
| /* Skip if gain calibration is inactive or | |
| * we already handle a probe request */ | |
| if (ah->ah_gain.g_state != AR5K_RFGAIN_ACTIVE) | |
| return; | |
| /* Send the packet with 2dB below max power as | |
| * patent doc suggest */ | |
| ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txpower.txp_max_pwr - 4, | |
| AR5K_PHY_PAPD_PROBE_TXPOWER) | | |
| AR5K_PHY_PAPD_PROBE_TX_NEXT, AR5K_PHY_PAPD_PROBE); | |
| ah->ah_gain.g_state = AR5K_RFGAIN_READ_REQUESTED; | |
| } | |
| /* Calculate gain_F measurement correction | |
| * based on the current step for RF5112 rev. 2 */ | |
| static u32 ath5k_hw_rf_gainf_corr(struct ath5k_hw *ah) | |
| { | |
| u32 mix, step; | |
| u32 *rf; | |
| const struct ath5k_gain_opt *go; | |
| const struct ath5k_gain_opt_step *g_step; | |
| const struct ath5k_rf_reg *rf_regs; | |
| /* Only RF5112 Rev. 2 supports it */ | |
| if ((ah->ah_radio != AR5K_RF5112) || | |
| (ah->ah_radio_5ghz_revision <= AR5K_SREV_RAD_5112A)) | |
| return 0; | |
| go = &rfgain_opt_5112; | |
| rf_regs = rf_regs_5112a; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a); | |
| g_step = &go->go_step[ah->ah_gain.g_step_idx]; | |
| if (ah->ah_rf_banks == NULL) | |
| return 0; | |
| rf = ah->ah_rf_banks; | |
| ah->ah_gain.g_f_corr = 0; | |
| /* No VGA (Variable Gain Amplifier) override, skip */ | |
| if (ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, false) != 1) | |
| return 0; | |
| /* Mix gain stepping */ | |
| step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXGAIN_STEP, false); | |
| /* Mix gain override */ | |
| mix = g_step->gos_param[0]; | |
| switch (mix) { | |
| case 3: | |
| ah->ah_gain.g_f_corr = step * 2; | |
| break; | |
| case 2: | |
| ah->ah_gain.g_f_corr = (step - 5) * 2; | |
| break; | |
| case 1: | |
| ah->ah_gain.g_f_corr = step; | |
| break; | |
| default: | |
| ah->ah_gain.g_f_corr = 0; | |
| break; | |
| } | |
| return ah->ah_gain.g_f_corr; | |
| } | |
| /* Check if current gain_F measurement is in the range of our | |
| * power detector windows. If we get a measurement outside range | |
| * we know it's not accurate (detectors can't measure anything outside | |
| * their detection window) so we must ignore it */ | |
| static bool ath5k_hw_rf_check_gainf_readback(struct ath5k_hw *ah) | |
| { | |
| const struct ath5k_rf_reg *rf_regs; | |
| u32 step, mix_ovr, level[4]; | |
| u32 *rf; | |
| if (ah->ah_rf_banks == NULL) | |
| return false; | |
| rf = ah->ah_rf_banks; | |
| if (ah->ah_radio == AR5K_RF5111) { | |
| rf_regs = rf_regs_5111; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111); | |
| step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_RFGAIN_STEP, | |
| false); | |
| level[0] = 0; | |
| level[1] = (step == 63) ? 50 : step + 4; | |
| level[2] = (step != 63) ? 64 : level[0]; | |
| level[3] = level[2] + 50 ; | |
| ah->ah_gain.g_high = level[3] - | |
| (step == 63 ? AR5K_GAIN_DYN_ADJUST_HI_MARGIN : -5); | |
| ah->ah_gain.g_low = level[0] + | |
| (step == 63 ? AR5K_GAIN_DYN_ADJUST_LO_MARGIN : 0); | |
| } else { | |
| rf_regs = rf_regs_5112; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112); | |
| mix_ovr = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, | |
| false); | |
| level[0] = level[2] = 0; | |
| if (mix_ovr == 1) { | |
| level[1] = level[3] = 83; | |
| } else { | |
| level[1] = level[3] = 107; | |
| ah->ah_gain.g_high = 55; | |
| } | |
| } | |
| return (ah->ah_gain.g_current >= level[0] && | |
| ah->ah_gain.g_current <= level[1]) || | |
| (ah->ah_gain.g_current >= level[2] && | |
| ah->ah_gain.g_current <= level[3]); | |
| } | |
| /* Perform gain_F adjustment by choosing the right set | |
| * of parameters from rf gain optimization ladder */ | |
| static s8 ath5k_hw_rf_gainf_adjust(struct ath5k_hw *ah) | |
| { | |
| const struct ath5k_gain_opt *go; | |
| const struct ath5k_gain_opt_step *g_step; | |
| int ret = 0; | |
| switch (ah->ah_radio) { | |
| case AR5K_RF5111: | |
| go = &rfgain_opt_5111; | |
| break; | |
| case AR5K_RF5112: | |
| go = &rfgain_opt_5112; | |
| break; | |
| default: | |
| return 0; | |
| } | |
| g_step = &go->go_step[ah->ah_gain.g_step_idx]; | |
| if (ah->ah_gain.g_current >= ah->ah_gain.g_high) { | |
| /* Reached maximum */ | |
| if (ah->ah_gain.g_step_idx == 0) | |
| return -1; | |
| for (ah->ah_gain.g_target = ah->ah_gain.g_current; | |
| ah->ah_gain.g_target >= ah->ah_gain.g_high && | |
| ah->ah_gain.g_step_idx > 0; | |
| g_step = &go->go_step[ah->ah_gain.g_step_idx]) | |
| ah->ah_gain.g_target -= 2 * | |
| (go->go_step[--(ah->ah_gain.g_step_idx)].gos_gain - | |
| g_step->gos_gain); | |
| ret = 1; | |
| goto done; | |
| } | |
| if (ah->ah_gain.g_current <= ah->ah_gain.g_low) { | |
| /* Reached minimum */ | |
| if (ah->ah_gain.g_step_idx == (go->go_steps_count - 1)) | |
| return -2; | |
| for (ah->ah_gain.g_target = ah->ah_gain.g_current; | |
| ah->ah_gain.g_target <= ah->ah_gain.g_low && | |
| ah->ah_gain.g_step_idx < go->go_steps_count-1; | |
| g_step = &go->go_step[ah->ah_gain.g_step_idx]) | |
| ah->ah_gain.g_target -= 2 * | |
| (go->go_step[++ah->ah_gain.g_step_idx].gos_gain - | |
| g_step->gos_gain); | |
| ret = 2; | |
| goto done; | |
| } | |
| done: | |
| ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, | |
| "ret %d, gain step %u, current gain %u, target gain %u\n", | |
| ret, ah->ah_gain.g_step_idx, ah->ah_gain.g_current, | |
| ah->ah_gain.g_target); | |
| return ret; | |
| } | |
| /* Main callback for thermal rf gain calibration engine | |
| * Check for a new gain reading and schedule an adjustment | |
| * if needed. | |
| * | |
| * TODO: Use sw interrupt to schedule reset if gain_F needs | |
| * adjustment */ | |
| enum ath5k_rfgain ath5k_hw_gainf_calibrate(struct ath5k_hw *ah) | |
| { | |
| u32 data, type; | |
| struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; | |
| ATH5K_TRACE(ah->ah_sc); | |
| if (ah->ah_rf_banks == NULL || | |
| ah->ah_gain.g_state == AR5K_RFGAIN_INACTIVE) | |
| return AR5K_RFGAIN_INACTIVE; | |
| /* No check requested, either engine is inactive | |
| * or an adjustment is already requested */ | |
| if (ah->ah_gain.g_state != AR5K_RFGAIN_READ_REQUESTED) | |
| goto done; | |
| /* Read the PAPD (Peak to Average Power Detector) | |
| * register */ | |
| data = ath5k_hw_reg_read(ah, AR5K_PHY_PAPD_PROBE); | |
| /* No probe is scheduled, read gain_F measurement */ | |
| if (!(data & AR5K_PHY_PAPD_PROBE_TX_NEXT)) { | |
| ah->ah_gain.g_current = data >> AR5K_PHY_PAPD_PROBE_GAINF_S; | |
| type = AR5K_REG_MS(data, AR5K_PHY_PAPD_PROBE_TYPE); | |
| /* If tx packet is CCK correct the gain_F measurement | |
| * by cck ofdm gain delta */ | |
| if (type == AR5K_PHY_PAPD_PROBE_TYPE_CCK) { | |
| if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) | |
| ah->ah_gain.g_current += | |
| ee->ee_cck_ofdm_gain_delta; | |
| else | |
| ah->ah_gain.g_current += | |
| AR5K_GAIN_CCK_PROBE_CORR; | |
| } | |
| /* Further correct gain_F measurement for | |
| * RF5112A radios */ | |
| if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) { | |
| ath5k_hw_rf_gainf_corr(ah); | |
| ah->ah_gain.g_current = | |
| ah->ah_gain.g_current >= ah->ah_gain.g_f_corr ? | |
| (ah->ah_gain.g_current-ah->ah_gain.g_f_corr) : | |
| 0; | |
| } | |
| /* Check if measurement is ok and if we need | |
| * to adjust gain, schedule a gain adjustment, | |
| * else switch back to the acive state */ | |
| if (ath5k_hw_rf_check_gainf_readback(ah) && | |
| AR5K_GAIN_CHECK_ADJUST(&ah->ah_gain) && | |
| ath5k_hw_rf_gainf_adjust(ah)) { | |
| ah->ah_gain.g_state = AR5K_RFGAIN_NEED_CHANGE; | |
| } else { | |
| ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; | |
| } | |
| } | |
| done: | |
| return ah->ah_gain.g_state; | |
| } | |
| /* Write initial rf gain table to set the RF sensitivity | |
| * this one works on all RF chips and has nothing to do | |
| * with gain_F calibration */ | |
| int ath5k_hw_rfgain_init(struct ath5k_hw *ah, unsigned int freq) | |
| { | |
| const struct ath5k_ini_rfgain *ath5k_rfg; | |
| unsigned int i, size; | |
| switch (ah->ah_radio) { | |
| case AR5K_RF5111: | |
| ath5k_rfg = rfgain_5111; | |
| size = ARRAY_SIZE(rfgain_5111); | |
| break; | |
| case AR5K_RF5112: | |
| ath5k_rfg = rfgain_5112; | |
| size = ARRAY_SIZE(rfgain_5112); | |
| break; | |
| case AR5K_RF2413: | |
| ath5k_rfg = rfgain_2413; | |
| size = ARRAY_SIZE(rfgain_2413); | |
| break; | |
| case AR5K_RF2316: | |
| ath5k_rfg = rfgain_2316; | |
| size = ARRAY_SIZE(rfgain_2316); | |
| break; | |
| case AR5K_RF5413: | |
| ath5k_rfg = rfgain_5413; | |
| size = ARRAY_SIZE(rfgain_5413); | |
| break; | |
| case AR5K_RF2317: | |
| case AR5K_RF2425: | |
| ath5k_rfg = rfgain_2425; | |
| size = ARRAY_SIZE(rfgain_2425); | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| switch (freq) { | |
| case AR5K_INI_RFGAIN_2GHZ: | |
| case AR5K_INI_RFGAIN_5GHZ: | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| for (i = 0; i < size; i++) { | |
| AR5K_REG_WAIT(i); | |
| ath5k_hw_reg_write(ah, ath5k_rfg[i].rfg_value[freq], | |
| (u32)ath5k_rfg[i].rfg_register); | |
| } | |
| return 0; | |
| } | |
| /********************\ | |
| * RF Registers setup * | |
| \********************/ | |
| /* | |
| * Setup RF registers by writing rf buffer on hw | |
| */ | |
| int ath5k_hw_rfregs_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, | |
| unsigned int mode) | |
| { | |
| const struct ath5k_rf_reg *rf_regs; | |
| const struct ath5k_ini_rfbuffer *ini_rfb; | |
| const struct ath5k_gain_opt *go = NULL; | |
| const struct ath5k_gain_opt_step *g_step; | |
| struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; | |
| u8 ee_mode = 0; | |
| u32 *rfb; | |
| int i, obdb = -1, bank = -1; | |
| switch (ah->ah_radio) { | |
| case AR5K_RF5111: | |
| rf_regs = rf_regs_5111; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111); | |
| ini_rfb = rfb_5111; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5111); | |
| go = &rfgain_opt_5111; | |
| break; | |
| case AR5K_RF5112: | |
| if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) { | |
| rf_regs = rf_regs_5112a; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a); | |
| ini_rfb = rfb_5112a; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112a); | |
| } else { | |
| rf_regs = rf_regs_5112; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112); | |
| ini_rfb = rfb_5112; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112); | |
| } | |
| go = &rfgain_opt_5112; | |
| break; | |
| case AR5K_RF2413: | |
| rf_regs = rf_regs_2413; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2413); | |
| ini_rfb = rfb_2413; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2413); | |
| break; | |
| case AR5K_RF2316: | |
| rf_regs = rf_regs_2316; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2316); | |
| ini_rfb = rfb_2316; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2316); | |
| break; | |
| case AR5K_RF5413: | |
| rf_regs = rf_regs_5413; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5413); | |
| ini_rfb = rfb_5413; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5413); | |
| break; | |
| case AR5K_RF2317: | |
| rf_regs = rf_regs_2425; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425); | |
| ini_rfb = rfb_2317; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2317); | |
| break; | |
| case AR5K_RF2425: | |
| rf_regs = rf_regs_2425; | |
| ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425); | |
| if (ah->ah_mac_srev < AR5K_SREV_AR2417) { | |
| ini_rfb = rfb_2425; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2425); | |
| } else { | |
| ini_rfb = rfb_2417; | |
| ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2417); | |
| } | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| /* If it's the first time we set rf buffer, allocate | |
| * ah->ah_rf_banks based on ah->ah_rf_banks_size | |
| * we set above */ | |
| if (ah->ah_rf_banks == NULL) { | |
| ah->ah_rf_banks = kmalloc(sizeof(u32) * ah->ah_rf_banks_size, | |
| GFP_KERNEL); | |
| if (ah->ah_rf_banks == NULL) { | |
| ATH5K_ERR(ah->ah_sc, "out of memory\n"); | |
| return -ENOMEM; | |
| } | |
| } | |
| /* Copy values to modify them */ | |
| rfb = ah->ah_rf_banks; | |
| for (i = 0; i < ah->ah_rf_banks_size; i++) { | |
| if (ini_rfb[i].rfb_bank >= AR5K_MAX_RF_BANKS) { | |
| ATH5K_ERR(ah->ah_sc, "invalid bank\n"); | |
| return -EINVAL; | |
| } | |
| /* Bank changed, write down the offset */ | |
| if (bank != ini_rfb[i].rfb_bank) { | |
| bank = ini_rfb[i].rfb_bank; | |
| ah->ah_offset[bank] = i; | |
| } | |
| rfb[i] = ini_rfb[i].rfb_mode_data[mode]; | |
| } | |
| /* Set Output and Driver bias current (OB/DB) */ | |
| if (channel->hw_value & CHANNEL_2GHZ) { | |
| if (channel->hw_value & CHANNEL_CCK) | |
| ee_mode = AR5K_EEPROM_MODE_11B; | |
| else | |
| ee_mode = AR5K_EEPROM_MODE_11G; | |
| /* For RF511X/RF211X combination we | |
| * use b_OB and b_DB parameters stored | |
| * in eeprom on ee->ee_ob[ee_mode][0] | |
| * | |
| * For all other chips we use OB/DB for 2Ghz | |
| * stored in the b/g modal section just like | |
| * 802.11a on ee->ee_ob[ee_mode][1] */ | |
| if ((ah->ah_radio == AR5K_RF5111) || | |
| (ah->ah_radio == AR5K_RF5112)) | |
| obdb = 0; | |
| else | |
| obdb = 1; | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb], | |
| AR5K_RF_OB_2GHZ, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb], | |
| AR5K_RF_DB_2GHZ, true); | |
| /* RF5111 always needs OB/DB for 5GHz, even if we use 2GHz */ | |
| } else if ((channel->hw_value & CHANNEL_5GHZ) || | |
| (ah->ah_radio == AR5K_RF5111)) { | |
| /* For 11a, Turbo and XR we need to choose | |
| * OB/DB based on frequency range */ | |
| ee_mode = AR5K_EEPROM_MODE_11A; | |
| obdb = channel->center_freq >= 5725 ? 3 : | |
| (channel->center_freq >= 5500 ? 2 : | |
| (channel->center_freq >= 5260 ? 1 : | |
| (channel->center_freq > 4000 ? 0 : -1))); | |
| if (obdb < 0) | |
| return -EINVAL; | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb], | |
| AR5K_RF_OB_5GHZ, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb], | |
| AR5K_RF_DB_5GHZ, true); | |
| } | |
| g_step = &go->go_step[ah->ah_gain.g_step_idx]; | |
| /* Bank Modifications (chip-specific) */ | |
| if (ah->ah_radio == AR5K_RF5111) { | |
| /* Set gain_F settings according to current step */ | |
| if (channel->hw_value & CHANNEL_OFDM) { | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_FRAME_CTL, | |
| AR5K_PHY_FRAME_CTL_TX_CLIP, | |
| g_step->gos_param[0]); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1], | |
| AR5K_RF_PWD_90, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2], | |
| AR5K_RF_PWD_84, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3], | |
| AR5K_RF_RFGAIN_SEL, true); | |
| /* We programmed gain_F parameters, switch back | |
| * to active state */ | |
| ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; | |
| } | |
| /* Bank 6/7 setup */ | |
| ath5k_hw_rfb_op(ah, rf_regs, !ee->ee_xpd[ee_mode], | |
| AR5K_RF_PWD_XPD, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_x_gain[ee_mode], | |
| AR5K_RF_XPD_GAIN, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode], | |
| AR5K_RF_GAIN_I, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode], | |
| AR5K_RF_PLO_SEL, true); | |
| /* TODO: Half/quarter channel support */ | |
| } | |
| if (ah->ah_radio == AR5K_RF5112) { | |
| /* Set gain_F settings according to current step */ | |
| if (channel->hw_value & CHANNEL_OFDM) { | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[0], | |
| AR5K_RF_MIXGAIN_OVR, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1], | |
| AR5K_RF_PWD_138, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2], | |
| AR5K_RF_PWD_137, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3], | |
| AR5K_RF_PWD_136, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[4], | |
| AR5K_RF_PWD_132, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[5], | |
| AR5K_RF_PWD_131, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[6], | |
| AR5K_RF_PWD_130, true); | |
| /* We programmed gain_F parameters, switch back | |
| * to active state */ | |
| ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE; | |
| } | |
| /* Bank 6/7 setup */ | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode], | |
| AR5K_RF_XPD_SEL, true); | |
| if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112A) { | |
| /* Rev. 1 supports only one xpd */ | |
| ath5k_hw_rfb_op(ah, rf_regs, | |
| ee->ee_x_gain[ee_mode], | |
| AR5K_RF_XPD_GAIN, true); | |
| } else { | |
| /* TODO: Set high and low gain bits */ | |
| ath5k_hw_rfb_op(ah, rf_regs, | |
| ee->ee_x_gain[ee_mode], | |
| AR5K_RF_PD_GAIN_LO, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, | |
| ee->ee_x_gain[ee_mode], | |
| AR5K_RF_PD_GAIN_HI, true); | |
| /* Lower synth voltage on Rev 2 */ | |
| ath5k_hw_rfb_op(ah, rf_regs, 2, | |
| AR5K_RF_HIGH_VC_CP, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, 2, | |
| AR5K_RF_MID_VC_CP, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, 2, | |
| AR5K_RF_LOW_VC_CP, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, 2, | |
| AR5K_RF_PUSH_UP, true); | |
| /* Decrease power consumption on 5213+ BaseBand */ | |
| if (ah->ah_phy_revision >= AR5K_SREV_PHY_5212A) { | |
| ath5k_hw_rfb_op(ah, rf_regs, 1, | |
| AR5K_RF_PAD2GND, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, 1, | |
| AR5K_RF_XB2_LVL, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, 1, | |
| AR5K_RF_XB5_LVL, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, 1, | |
| AR5K_RF_PWD_167, true); | |
| ath5k_hw_rfb_op(ah, rf_regs, 1, | |
| AR5K_RF_PWD_166, true); | |
| } | |
| } | |
| ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode], | |
| AR5K_RF_GAIN_I, true); | |
| /* TODO: Half/quarter channel support */ | |
| } | |
| if (ah->ah_radio == AR5K_RF5413 && | |
| channel->hw_value & CHANNEL_2GHZ) { | |
| ath5k_hw_rfb_op(ah, rf_regs, 1, AR5K_RF_DERBY_CHAN_SEL_MODE, | |
| true); | |
| /* Set optimum value for early revisions (on pci-e chips) */ | |
| if (ah->ah_mac_srev >= AR5K_SREV_AR5424 && | |
| ah->ah_mac_srev < AR5K_SREV_AR5413) | |
| ath5k_hw_rfb_op(ah, rf_regs, ath5k_hw_bitswap(6, 3), | |
| AR5K_RF_PWD_ICLOBUF_2G, true); | |
| } | |
| /* Write RF banks on hw */ | |
| for (i = 0; i < ah->ah_rf_banks_size; i++) { | |
| AR5K_REG_WAIT(i); | |
| ath5k_hw_reg_write(ah, rfb[i], ini_rfb[i].rfb_ctrl_register); | |
| } | |
| return 0; | |
| } | |
| /**************************\ | |
| PHY/RF channel functions | |
| \**************************/ | |
| /* | |
| * Check if a channel is supported | |
| */ | |
| bool ath5k_channel_ok(struct ath5k_hw *ah, u16 freq, unsigned int flags) | |
| { | |
| /* Check if the channel is in our supported range */ | |
| if (flags & CHANNEL_2GHZ) { | |
| if ((freq >= ah->ah_capabilities.cap_range.range_2ghz_min) && | |
| (freq <= ah->ah_capabilities.cap_range.range_2ghz_max)) | |
| return true; | |
| } else if (flags & CHANNEL_5GHZ) | |
| if ((freq >= ah->ah_capabilities.cap_range.range_5ghz_min) && | |
| (freq <= ah->ah_capabilities.cap_range.range_5ghz_max)) | |
| return true; | |
| return false; | |
| } | |
| /* | |
| * Convertion needed for RF5110 | |
| */ | |
| static u32 ath5k_hw_rf5110_chan2athchan(struct ieee80211_channel *channel) | |
| { | |
| u32 athchan; | |
| /* | |
| * Convert IEEE channel/MHz to an internal channel value used | |
| * by the AR5210 chipset. This has not been verified with | |
| * newer chipsets like the AR5212A who have a completely | |
| * different RF/PHY part. | |
| */ | |
| athchan = (ath5k_hw_bitswap( | |
| (ieee80211_frequency_to_channel( | |
| channel->center_freq) - 24) / 2, 5) | |
| << 1) | (1 << 6) | 0x1; | |
| return athchan; | |
| } | |
| /* | |
| * Set channel on RF5110 | |
| */ | |
| static int ath5k_hw_rf5110_channel(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| u32 data; | |
| /* | |
| * Set the channel and wait | |
| */ | |
| data = ath5k_hw_rf5110_chan2athchan(channel); | |
| ath5k_hw_reg_write(ah, data, AR5K_RF_BUFFER); | |
| ath5k_hw_reg_write(ah, 0, AR5K_RF_BUFFER_CONTROL_0); | |
| mdelay(1); | |
| return 0; | |
| } | |
| /* | |
| * Convertion needed for 5111 | |
| */ | |
| static int ath5k_hw_rf5111_chan2athchan(unsigned int ieee, | |
| struct ath5k_athchan_2ghz *athchan) | |
| { | |
| int channel; | |
| /* Cast this value to catch negative channel numbers (>= -19) */ | |
| channel = (int)ieee; | |
| /* | |
| * Map 2GHz IEEE channel to 5GHz Atheros channel | |
| */ | |
| if (channel <= 13) { | |
| athchan->a2_athchan = 115 + channel; | |
| athchan->a2_flags = 0x46; | |
| } else if (channel == 14) { | |
| athchan->a2_athchan = 124; | |
| athchan->a2_flags = 0x44; | |
| } else if (channel >= 15 && channel <= 26) { | |
| athchan->a2_athchan = ((channel - 14) * 4) + 132; | |
| athchan->a2_flags = 0x46; | |
| } else | |
| return -EINVAL; | |
| return 0; | |
| } | |
| /* | |
| * Set channel on 5111 | |
| */ | |
| static int ath5k_hw_rf5111_channel(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| struct ath5k_athchan_2ghz ath5k_channel_2ghz; | |
| unsigned int ath5k_channel = | |
| ieee80211_frequency_to_channel(channel->center_freq); | |
| u32 data0, data1, clock; | |
| int ret; | |
| /* | |
| * Set the channel on the RF5111 radio | |
| */ | |
| data0 = data1 = 0; | |
| if (channel->hw_value & CHANNEL_2GHZ) { | |
| /* Map 2GHz channel to 5GHz Atheros channel ID */ | |
| ret = ath5k_hw_rf5111_chan2athchan( | |
| ieee80211_frequency_to_channel(channel->center_freq), | |
| &ath5k_channel_2ghz); | |
| if (ret) | |
| return ret; | |
| ath5k_channel = ath5k_channel_2ghz.a2_athchan; | |
| data0 = ((ath5k_hw_bitswap(ath5k_channel_2ghz.a2_flags, 8) & 0xff) | |
| << 5) | (1 << 4); | |
| } | |
| if (ath5k_channel < 145 || !(ath5k_channel & 1)) { | |
| clock = 1; | |
| data1 = ((ath5k_hw_bitswap(ath5k_channel - 24, 8) & 0xff) << 2) | | |
| (clock << 1) | (1 << 10) | 1; | |
| } else { | |
| clock = 0; | |
| data1 = ((ath5k_hw_bitswap((ath5k_channel - 24) / 2, 8) & 0xff) | |
| << 2) | (clock << 1) | (1 << 10) | 1; | |
| } | |
| ath5k_hw_reg_write(ah, (data1 & 0xff) | ((data0 & 0xff) << 8), | |
| AR5K_RF_BUFFER); | |
| ath5k_hw_reg_write(ah, ((data1 >> 8) & 0xff) | (data0 & 0xff00), | |
| AR5K_RF_BUFFER_CONTROL_3); | |
| return 0; | |
| } | |
| /* | |
| * Set channel on 5112 and newer | |
| */ | |
| static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| u32 data, data0, data1, data2; | |
| u16 c; | |
| data = data0 = data1 = data2 = 0; | |
| c = channel->center_freq; | |
| if (c < 4800) { | |
| if (!((c - 2224) % 5)) { | |
| data0 = ((2 * (c - 704)) - 3040) / 10; | |
| data1 = 1; | |
| } else if (!((c - 2192) % 5)) { | |
| data0 = ((2 * (c - 672)) - 3040) / 10; | |
| data1 = 0; | |
| } else | |
| return -EINVAL; | |
| data0 = ath5k_hw_bitswap((data0 << 2) & 0xff, 8); | |
| } else if ((c - (c % 5)) != 2 || c > 5435) { | |
| if (!(c % 20) && c >= 5120) { | |
| data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); | |
| data2 = ath5k_hw_bitswap(3, 2); | |
| } else if (!(c % 10)) { | |
| data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); | |
| data2 = ath5k_hw_bitswap(2, 2); | |
| } else if (!(c % 5)) { | |
| data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); | |
| data2 = ath5k_hw_bitswap(1, 2); | |
| } else | |
| return -EINVAL; | |
| } else { | |
| data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8); | |
| data2 = ath5k_hw_bitswap(0, 2); | |
| } | |
| data = (data0 << 4) | (data1 << 1) | (data2 << 2) | 0x1001; | |
| ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); | |
| ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); | |
| return 0; | |
| } | |
| /* | |
| * Set the channel on the RF2425 | |
| */ | |
| static int ath5k_hw_rf2425_channel(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| u32 data, data0, data2; | |
| u16 c; | |
| data = data0 = data2 = 0; | |
| c = channel->center_freq; | |
| if (c < 4800) { | |
| data0 = ath5k_hw_bitswap((c - 2272), 8); | |
| data2 = 0; | |
| /* ? 5GHz ? */ | |
| } else if ((c - (c % 5)) != 2 || c > 5435) { | |
| if (!(c % 20) && c < 5120) | |
| data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); | |
| else if (!(c % 10)) | |
| data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); | |
| else if (!(c % 5)) | |
| data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); | |
| else | |
| return -EINVAL; | |
| data2 = ath5k_hw_bitswap(1, 2); | |
| } else { | |
| data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8); | |
| data2 = ath5k_hw_bitswap(0, 2); | |
| } | |
| data = (data0 << 4) | data2 << 2 | 0x1001; | |
| ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); | |
| ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); | |
| return 0; | |
| } | |
| /* | |
| * Set a channel on the radio chip | |
| */ | |
| int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel) | |
| { | |
| int ret; | |
| /* | |
| * Check bounds supported by the PHY (we don't care about regultory | |
| * restrictions at this point). Note: hw_value already has the band | |
| * (CHANNEL_2GHZ, or CHANNEL_5GHZ) so we inform ath5k_channel_ok() | |
| * of the band by that */ | |
| if (!ath5k_channel_ok(ah, channel->center_freq, channel->hw_value)) { | |
| ATH5K_ERR(ah->ah_sc, | |
| "channel frequency (%u MHz) out of supported " | |
| "band range\n", | |
| channel->center_freq); | |
| return -EINVAL; | |
| } | |
| /* | |
| * Set the channel and wait | |
| */ | |
| switch (ah->ah_radio) { | |
| case AR5K_RF5110: | |
| ret = ath5k_hw_rf5110_channel(ah, channel); | |
| break; | |
| case AR5K_RF5111: | |
| ret = ath5k_hw_rf5111_channel(ah, channel); | |
| break; | |
| case AR5K_RF2425: | |
| ret = ath5k_hw_rf2425_channel(ah, channel); | |
| break; | |
| default: | |
| ret = ath5k_hw_rf5112_channel(ah, channel); | |
| break; | |
| } | |
| if (ret) | |
| return ret; | |
| /* Set JAPAN setting for channel 14 */ | |
| if (channel->center_freq == 2484) { | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, | |
| AR5K_PHY_CCKTXCTL_JAPAN); | |
| } else { | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, | |
| AR5K_PHY_CCKTXCTL_WORLD); | |
| } | |
| ah->ah_current_channel.center_freq = channel->center_freq; | |
| ah->ah_current_channel.hw_value = channel->hw_value; | |
| ah->ah_turbo = channel->hw_value == CHANNEL_T ? true : false; | |
| return 0; | |
| } | |
| /*****************\ | |
| PHY calibration | |
| \*****************/ | |
| /** | |
| * ath5k_hw_noise_floor_calibration - perform PHY noise floor calibration | |
| * | |
| * @ah: struct ath5k_hw pointer we are operating on | |
| * @freq: the channel frequency, just used for error logging | |
| * | |
| * This function performs a noise floor calibration of the PHY and waits for | |
| * it to complete. Then the noise floor value is compared to some maximum | |
| * noise floor we consider valid. | |
| * | |
| * Note that this is different from what the madwifi HAL does: it reads the | |
| * noise floor and afterwards initiates the calibration. Since the noise floor | |
| * calibration can take some time to finish, depending on the current channel | |
| * use, that avoids the occasional timeout warnings we are seeing now. | |
| * | |
| * See the following link for an Atheros patent on noise floor calibration: | |
| * http://patft.uspto.gov/netacgi/nph-Parser?Sect1=PTO1&Sect2=HITOFF&d=PALL \ | |
| * &p=1&u=%2Fnetahtml%2FPTO%2Fsrchnum.htm&r=1&f=G&l=50&s1=7245893.PN.&OS=PN/7 | |
| * | |
| * XXX: Since during noise floor calibration antennas are detached according to | |
| * the patent, we should stop tx queues here. | |
| */ | |
| int | |
| ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq) | |
| { | |
| int ret; | |
| unsigned int i; | |
| s32 noise_floor; | |
| /* | |
| * Enable noise floor calibration | |
| */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, | |
| AR5K_PHY_AGCCTL_NF); | |
| ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, | |
| AR5K_PHY_AGCCTL_NF, 0, false); | |
| if (ret) { | |
| ATH5K_ERR(ah->ah_sc, | |
| "noise floor calibration timeout (%uMHz)\n", freq); | |
| return -EAGAIN; | |
| } | |
| /* Wait until the noise floor is calibrated and read the value */ | |
| for (i = 20; i > 0; i--) { | |
| mdelay(1); | |
| noise_floor = ath5k_hw_reg_read(ah, AR5K_PHY_NF); | |
| noise_floor = AR5K_PHY_NF_RVAL(noise_floor); | |
| if (noise_floor & AR5K_PHY_NF_ACTIVE) { | |
| noise_floor = AR5K_PHY_NF_AVAL(noise_floor); | |
| if (noise_floor <= AR5K_TUNE_NOISE_FLOOR) | |
| break; | |
| } | |
| } | |
| ATH5K_DBG_UNLIMIT(ah->ah_sc, ATH5K_DEBUG_CALIBRATE, | |
| "noise floor %d\n", noise_floor); | |
| if (noise_floor > AR5K_TUNE_NOISE_FLOOR) { | |
| ATH5K_ERR(ah->ah_sc, | |
| "noise floor calibration failed (%uMHz)\n", freq); | |
| return -EAGAIN; | |
| } | |
| ah->ah_noise_floor = noise_floor; | |
| return 0; | |
| } | |
| /* | |
| * Perform a PHY calibration on RF5110 | |
| * -Fix BPSK/QAM Constellation (I/Q correction) | |
| * -Calculate Noise Floor | |
| */ | |
| static int ath5k_hw_rf5110_calibrate(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| u32 phy_sig, phy_agc, phy_sat, beacon; | |
| int ret; | |
| /* | |
| * Disable beacons and RX/TX queues, wait | |
| */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5210, | |
| AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210); | |
| beacon = ath5k_hw_reg_read(ah, AR5K_BEACON_5210); | |
| ath5k_hw_reg_write(ah, beacon & ~AR5K_BEACON_ENABLE, AR5K_BEACON_5210); | |
| mdelay(2); | |
| /* | |
| * Set the channel (with AGC turned off) | |
| */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); | |
| udelay(10); | |
| ret = ath5k_hw_channel(ah, channel); | |
| /* | |
| * Activate PHY and wait | |
| */ | |
| ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT); | |
| mdelay(1); | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); | |
| if (ret) | |
| return ret; | |
| /* | |
| * Calibrate the radio chip | |
| */ | |
| /* Remember normal state */ | |
| phy_sig = ath5k_hw_reg_read(ah, AR5K_PHY_SIG); | |
| phy_agc = ath5k_hw_reg_read(ah, AR5K_PHY_AGCCOARSE); | |
| phy_sat = ath5k_hw_reg_read(ah, AR5K_PHY_ADCSAT); | |
| /* Update radio registers */ | |
| ath5k_hw_reg_write(ah, (phy_sig & ~(AR5K_PHY_SIG_FIRPWR)) | | |
| AR5K_REG_SM(-1, AR5K_PHY_SIG_FIRPWR), AR5K_PHY_SIG); | |
| ath5k_hw_reg_write(ah, (phy_agc & ~(AR5K_PHY_AGCCOARSE_HI | | |
| AR5K_PHY_AGCCOARSE_LO)) | | |
| AR5K_REG_SM(-1, AR5K_PHY_AGCCOARSE_HI) | | |
| AR5K_REG_SM(-127, AR5K_PHY_AGCCOARSE_LO), AR5K_PHY_AGCCOARSE); | |
| ath5k_hw_reg_write(ah, (phy_sat & ~(AR5K_PHY_ADCSAT_ICNT | | |
| AR5K_PHY_ADCSAT_THR)) | | |
| AR5K_REG_SM(2, AR5K_PHY_ADCSAT_ICNT) | | |
| AR5K_REG_SM(12, AR5K_PHY_ADCSAT_THR), AR5K_PHY_ADCSAT); | |
| udelay(20); | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); | |
| udelay(10); | |
| ath5k_hw_reg_write(ah, AR5K_PHY_RFSTG_DISABLE, AR5K_PHY_RFSTG); | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE); | |
| mdelay(1); | |
| /* | |
| * Enable calibration and wait until completion | |
| */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_CAL); | |
| ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, | |
| AR5K_PHY_AGCCTL_CAL, 0, false); | |
| /* Reset to normal state */ | |
| ath5k_hw_reg_write(ah, phy_sig, AR5K_PHY_SIG); | |
| ath5k_hw_reg_write(ah, phy_agc, AR5K_PHY_AGCCOARSE); | |
| ath5k_hw_reg_write(ah, phy_sat, AR5K_PHY_ADCSAT); | |
| if (ret) { | |
| ATH5K_ERR(ah->ah_sc, "calibration timeout (%uMHz)\n", | |
| channel->center_freq); | |
| return ret; | |
| } | |
| ath5k_hw_noise_floor_calibration(ah, channel->center_freq); | |
| /* | |
| * Re-enable RX/TX and beacons | |
| */ | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_DIAG_SW_5210, | |
| AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210); | |
| ath5k_hw_reg_write(ah, beacon, AR5K_BEACON_5210); | |
| return 0; | |
| } | |
| /* | |
| * Perform a PHY calibration on RF5111/5112 and newer chips | |
| */ | |
| static int ath5k_hw_rf511x_calibrate(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| u32 i_pwr, q_pwr; | |
| s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd; | |
| int i; | |
| ATH5K_TRACE(ah->ah_sc); | |
| if (!ah->ah_calibration || | |
| ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) | |
| goto done; | |
| /* Calibration has finished, get the results and re-run */ | |
| for (i = 0; i <= 10; i++) { | |
| iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR); | |
| i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I); | |
| q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q); | |
| } | |
| i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7; | |
| q_coffd = q_pwr >> 7; | |
| /* No correction */ | |
| if (i_coffd == 0 || q_coffd == 0) | |
| goto done; | |
| i_coff = ((-iq_corr) / i_coffd) & 0x3f; | |
| /* Boundary check */ | |
| if (i_coff > 31) | |
| i_coff = 31; | |
| if (i_coff < -32) | |
| i_coff = -32; | |
| q_coff = (((s32)i_pwr / q_coffd) - 128) & 0x1f; | |
| /* Boundary check */ | |
| if (q_coff > 15) | |
| q_coff = 15; | |
| if (q_coff < -16) | |
| q_coff = -16; | |
| /* Commit new I/Q value */ | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE | | |
| ((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S)); | |
| /* Re-enable calibration -if we don't we'll commit | |
| * the same values again and again */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, | |
| AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_RUN); | |
| done: | |
| /* TODO: Separate noise floor calibration from I/Q calibration | |
| * since noise floor calibration interrupts rx path while I/Q | |
| * calibration doesn't. We don't need to run noise floor calibration | |
| * as often as I/Q calibration.*/ | |
| ath5k_hw_noise_floor_calibration(ah, channel->center_freq); | |
| /* Initiate a gain_F calibration */ | |
| ath5k_hw_request_rfgain_probe(ah); | |
| return 0; | |
| } | |
| /* | |
| * Perform a PHY calibration | |
| */ | |
| int ath5k_hw_phy_calibrate(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| int ret; | |
| if (ah->ah_radio == AR5K_RF5110) | |
| ret = ath5k_hw_rf5110_calibrate(ah, channel); | |
| else | |
| ret = ath5k_hw_rf511x_calibrate(ah, channel); | |
| return ret; | |
| } | |
| int ath5k_hw_phy_disable(struct ath5k_hw *ah) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| /*Just a try M.F.*/ | |
| ath5k_hw_reg_write(ah, AR5K_PHY_ACT_DISABLE, AR5K_PHY_ACT); | |
| return 0; | |
| } | |
| /********************\ | |
| Misc PHY functions | |
| \********************/ | |
| /* | |
| * Get the PHY Chip revision | |
| */ | |
| u16 ath5k_hw_radio_revision(struct ath5k_hw *ah, unsigned int chan) | |
| { | |
| unsigned int i; | |
| u32 srev; | |
| u16 ret; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* | |
| * Set the radio chip access register | |
| */ | |
| switch (chan) { | |
| case CHANNEL_2GHZ: | |
| ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_2GHZ, AR5K_PHY(0)); | |
| break; | |
| case CHANNEL_5GHZ: | |
| ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); | |
| break; | |
| default: | |
| return 0; | |
| } | |
| mdelay(2); | |
| /* ...wait until PHY is ready and read the selected radio revision */ | |
| ath5k_hw_reg_write(ah, 0x00001c16, AR5K_PHY(0x34)); | |
| for (i = 0; i < 8; i++) | |
| ath5k_hw_reg_write(ah, 0x00010000, AR5K_PHY(0x20)); | |
| if (ah->ah_version == AR5K_AR5210) { | |
| srev = ath5k_hw_reg_read(ah, AR5K_PHY(256) >> 28) & 0xf; | |
| ret = (u16)ath5k_hw_bitswap(srev, 4) + 1; | |
| } else { | |
| srev = (ath5k_hw_reg_read(ah, AR5K_PHY(0x100)) >> 24) & 0xff; | |
| ret = (u16)ath5k_hw_bitswap(((srev & 0xf0) >> 4) | | |
| ((srev & 0x0f) << 4), 8); | |
| } | |
| /* Reset to the 5GHz mode */ | |
| ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); | |
| return ret; | |
| } | |
| void /*TODO:Boundary check*/ | |
| ath5k_hw_set_def_antenna(struct ath5k_hw *ah, unsigned int ant) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| /*Just a try M.F.*/ | |
| if (ah->ah_version != AR5K_AR5210) | |
| ath5k_hw_reg_write(ah, ant, AR5K_DEFAULT_ANTENNA); | |
| } | |
| unsigned int ath5k_hw_get_def_antenna(struct ath5k_hw *ah) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| /*Just a try M.F.*/ | |
| if (ah->ah_version != AR5K_AR5210) | |
| return ath5k_hw_reg_read(ah, AR5K_DEFAULT_ANTENNA); | |
| return false; /*XXX: What do we return for 5210 ?*/ | |
| } | |
| /****************\ | |
| * TX power setup * | |
| \****************/ | |
| /* | |
| * Helper functions | |
| */ | |
| /* | |
| * Do linear interpolation between two given (x, y) points | |
| */ | |
| static s16 | |
| ath5k_get_interpolated_value(s16 target, s16 x_left, s16 x_right, | |
| s16 y_left, s16 y_right) | |
| { | |
| s16 ratio, result; | |
| /* Avoid divide by zero and skip interpolation | |
| * if we have the same point */ | |
| if ((x_left == x_right) || (y_left == y_right)) | |
| return y_left; | |
| /* | |
| * Since we use ints and not fps, we need to scale up in | |
| * order to get a sane ratio value (or else we 'll eg. get | |
| * always 1 instead of 1.25, 1.75 etc). We scale up by 100 | |
| * to have some accuracy both for 0.5 and 0.25 steps. | |
| */ | |
| ratio = ((100 * y_right - 100 * y_left)/(x_right - x_left)); | |
| /* Now scale down to be in range */ | |
| result = y_left + (ratio * (target - x_left) / 100); | |
| return result; | |
| } | |
| /* | |
| * Find vertical boundary (min pwr) for the linear PCDAC curve. | |
| * | |
| * Since we have the top of the curve and we draw the line below | |
| * until we reach 1 (1 pcdac step) we need to know which point | |
| * (x value) that is so that we don't go below y axis and have negative | |
| * pcdac values when creating the curve, or fill the table with zeroes. | |
| */ | |
| static s16 | |
| ath5k_get_linear_pcdac_min(const u8 *stepL, const u8 *stepR, | |
| const s16 *pwrL, const s16 *pwrR) | |
| { | |
| s8 tmp; | |
| s16 min_pwrL, min_pwrR; | |
| s16 pwr_i = pwrL[0]; | |
| do { | |
| pwr_i--; | |
| tmp = (s8) ath5k_get_interpolated_value(pwr_i, | |
| pwrL[0], pwrL[1], | |
| stepL[0], stepL[1]); | |
| } while (tmp > 1); | |
| min_pwrL = pwr_i; | |
| pwr_i = pwrR[0]; | |
| do { | |
| pwr_i--; | |
| tmp = (s8) ath5k_get_interpolated_value(pwr_i, | |
| pwrR[0], pwrR[1], | |
| stepR[0], stepR[1]); | |
| } while (tmp > 1); | |
| min_pwrR = pwr_i; | |
| /* Keep the right boundary so that it works for both curves */ | |
| return max(min_pwrL, min_pwrR); | |
| } | |
| /* | |
| * Interpolate (pwr,vpd) points to create a Power to PDADC or a | |
| * Power to PCDAC curve. | |
| * | |
| * Each curve has power on x axis (in 0.5dB units) and PCDAC/PDADC | |
| * steps (offsets) on y axis. Power can go up to 31.5dB and max | |
| * PCDAC/PDADC step for each curve is 64 but we can write more than | |
| * one curves on hw so we can go up to 128 (which is the max step we | |
| * can write on the final table). | |
| * | |
| * We write y values (PCDAC/PDADC steps) on hw. | |
| */ | |
| static void | |
| ath5k_create_power_curve(s16 pmin, s16 pmax, | |
| const s16 *pwr, const u8 *vpd, | |
| u8 num_points, | |
| u8 *vpd_table, u8 type) | |
| { | |
| u8 idx[2] = { 0, 1 }; | |
| s16 pwr_i = 2*pmin; | |
| int i; | |
| if (num_points < 2) | |
| return; | |
| /* We want the whole line, so adjust boundaries | |
| * to cover the entire power range. Note that | |
| * power values are already 0.25dB so no need | |
| * to multiply pwr_i by 2 */ | |
| if (type == AR5K_PWRTABLE_LINEAR_PCDAC) { | |
| pwr_i = pmin; | |
| pmin = 0; | |
| pmax = 63; | |
| } | |
| /* Find surrounding turning points (TPs) | |
| * and interpolate between them */ | |
| for (i = 0; (i <= (u16) (pmax - pmin)) && | |
| (i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) { | |
| /* We passed the right TP, move to the next set of TPs | |
| * if we pass the last TP, extrapolate above using the last | |
| * two TPs for ratio */ | |
| if ((pwr_i > pwr[idx[1]]) && (idx[1] < num_points - 1)) { | |
| idx[0]++; | |
| idx[1]++; | |
| } | |
| vpd_table[i] = (u8) ath5k_get_interpolated_value(pwr_i, | |
| pwr[idx[0]], pwr[idx[1]], | |
| vpd[idx[0]], vpd[idx[1]]); | |
| /* Increase by 0.5dB | |
| * (0.25 dB units) */ | |
| pwr_i += 2; | |
| } | |
| } | |
| /* | |
| * Get the surrounding per-channel power calibration piers | |
| * for a given frequency so that we can interpolate between | |
| * them and come up with an apropriate dataset for our current | |
| * channel. | |
| */ | |
| static void | |
| ath5k_get_chan_pcal_surrounding_piers(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel, | |
| struct ath5k_chan_pcal_info **pcinfo_l, | |
| struct ath5k_chan_pcal_info **pcinfo_r) | |
| { | |
| struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; | |
| struct ath5k_chan_pcal_info *pcinfo; | |
| u8 idx_l, idx_r; | |
| u8 mode, max, i; | |
| u32 target = channel->center_freq; | |
| idx_l = 0; | |
| idx_r = 0; | |
| if (!(channel->hw_value & CHANNEL_OFDM)) { | |
| pcinfo = ee->ee_pwr_cal_b; | |
| mode = AR5K_EEPROM_MODE_11B; | |
| } else if (channel->hw_value & CHANNEL_2GHZ) { | |
| pcinfo = ee->ee_pwr_cal_g; | |
| mode = AR5K_EEPROM_MODE_11G; | |
| } else { | |
| pcinfo = ee->ee_pwr_cal_a; | |
| mode = AR5K_EEPROM_MODE_11A; | |
| } | |
| max = ee->ee_n_piers[mode] - 1; | |
| /* Frequency is below our calibrated | |
| * range. Use the lowest power curve | |
| * we have */ | |
| if (target < pcinfo[0].freq) { | |
| idx_l = idx_r = 0; | |
| goto done; | |
| } | |
| /* Frequency is above our calibrated | |
| * range. Use the highest power curve | |
| * we have */ | |
| if (target > pcinfo[max].freq) { | |
| idx_l = idx_r = max; | |
| goto done; | |
| } | |
| /* Frequency is inside our calibrated | |
| * channel range. Pick the surrounding | |
| * calibration piers so that we can | |
| * interpolate */ | |
| for (i = 0; i <= max; i++) { | |
| /* Frequency matches one of our calibration | |
| * piers, no need to interpolate, just use | |
| * that calibration pier */ | |
| if (pcinfo[i].freq == target) { | |
| idx_l = idx_r = i; | |
| goto done; | |
| } | |
| /* We found a calibration pier that's above | |
| * frequency, use this pier and the previous | |
| * one to interpolate */ | |
| if (target < pcinfo[i].freq) { | |
| idx_r = i; | |
| idx_l = idx_r - 1; | |
| goto done; | |
| } | |
| } | |
| done: | |
| *pcinfo_l = &pcinfo[idx_l]; | |
| *pcinfo_r = &pcinfo[idx_r]; | |
| return; | |
| } | |
| /* | |
| * Get the surrounding per-rate power calibration data | |
| * for a given frequency and interpolate between power | |
| * values to set max target power supported by hw for | |
| * each rate. | |
| */ | |
| static void | |
| ath5k_get_rate_pcal_data(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel, | |
| struct ath5k_rate_pcal_info *rates) | |
| { | |
| struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; | |
| struct ath5k_rate_pcal_info *rpinfo; | |
| u8 idx_l, idx_r; | |
| u8 mode, max, i; | |
| u32 target = channel->center_freq; | |
| idx_l = 0; | |
| idx_r = 0; | |
| if (!(channel->hw_value & CHANNEL_OFDM)) { | |
| rpinfo = ee->ee_rate_tpwr_b; | |
| mode = AR5K_EEPROM_MODE_11B; | |
| } else if (channel->hw_value & CHANNEL_2GHZ) { | |
| rpinfo = ee->ee_rate_tpwr_g; | |
| mode = AR5K_EEPROM_MODE_11G; | |
| } else { | |
| rpinfo = ee->ee_rate_tpwr_a; | |
| mode = AR5K_EEPROM_MODE_11A; | |
| } | |
| max = ee->ee_rate_target_pwr_num[mode] - 1; | |
| /* Get the surrounding calibration | |
| * piers - same as above */ | |
| if (target < rpinfo[0].freq) { | |
| idx_l = idx_r = 0; | |
| goto done; | |
| } | |
| if (target > rpinfo[max].freq) { | |
| idx_l = idx_r = max; | |
| goto done; | |
| } | |
| for (i = 0; i <= max; i++) { | |
| if (rpinfo[i].freq == target) { | |
| idx_l = idx_r = i; | |
| goto done; | |
| } | |
| if (target < rpinfo[i].freq) { | |
| idx_r = i; | |
| idx_l = idx_r - 1; | |
| goto done; | |
| } | |
| } | |
| done: | |
| /* Now interpolate power value, based on the frequency */ | |
| rates->freq = target; | |
| rates->target_power_6to24 = | |
| ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, | |
| rpinfo[idx_r].freq, | |
| rpinfo[idx_l].target_power_6to24, | |
| rpinfo[idx_r].target_power_6to24); | |
| rates->target_power_36 = | |
| ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, | |
| rpinfo[idx_r].freq, | |
| rpinfo[idx_l].target_power_36, | |
| rpinfo[idx_r].target_power_36); | |
| rates->target_power_48 = | |
| ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, | |
| rpinfo[idx_r].freq, | |
| rpinfo[idx_l].target_power_48, | |
| rpinfo[idx_r].target_power_48); | |
| rates->target_power_54 = | |
| ath5k_get_interpolated_value(target, rpinfo[idx_l].freq, | |
| rpinfo[idx_r].freq, | |
| rpinfo[idx_l].target_power_54, | |
| rpinfo[idx_r].target_power_54); | |
| } | |
| /* | |
| * Get the max edge power for this channel if | |
| * we have such data from EEPROM's Conformance Test | |
| * Limits (CTL), and limit max power if needed. | |
| * | |
| * FIXME: Only works for world regulatory domains | |
| */ | |
| static void | |
| ath5k_get_max_ctl_power(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel) | |
| { | |
| struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; | |
| struct ath5k_edge_power *rep = ee->ee_ctl_pwr; | |
| u8 *ctl_val = ee->ee_ctl; | |
| s16 max_chan_pwr = ah->ah_txpower.txp_max_pwr / 4; | |
| s16 edge_pwr = 0; | |
| u8 rep_idx; | |
| u8 i, ctl_mode; | |
| u8 ctl_idx = 0xFF; | |
| u32 target = channel->center_freq; | |
| /* Find out a CTL for our mode that's not mapped | |
| * on a specific reg domain. | |
| * | |
| * TODO: Map our current reg domain to one of the 3 available | |
| * reg domain ids so that we can support more CTLs. */ | |
| switch (channel->hw_value & CHANNEL_MODES) { | |
| case CHANNEL_A: | |
| ctl_mode = AR5K_CTL_11A | AR5K_CTL_NO_REGDOMAIN; | |
| break; | |
| case CHANNEL_G: | |
| ctl_mode = AR5K_CTL_11G | AR5K_CTL_NO_REGDOMAIN; | |
| break; | |
| case CHANNEL_B: | |
| ctl_mode = AR5K_CTL_11B | AR5K_CTL_NO_REGDOMAIN; | |
| break; | |
| case CHANNEL_T: | |
| ctl_mode = AR5K_CTL_TURBO | AR5K_CTL_NO_REGDOMAIN; | |
| break; | |
| case CHANNEL_TG: | |
| ctl_mode = AR5K_CTL_TURBOG | AR5K_CTL_NO_REGDOMAIN; | |
| break; | |
| case CHANNEL_XR: | |
| /* Fall through */ | |
| default: | |
| return; | |
| } | |
| for (i = 0; i < ee->ee_ctls; i++) { | |
| if (ctl_val[i] == ctl_mode) { | |
| ctl_idx = i; | |
| break; | |
| } | |
| } | |
| /* If we have a CTL dataset available grab it and find the | |
| * edge power for our frequency */ | |
| if (ctl_idx == 0xFF) | |
| return; | |
| /* Edge powers are sorted by frequency from lower | |
| * to higher. Each CTL corresponds to 8 edge power | |
| * measurements. */ | |
| rep_idx = ctl_idx * AR5K_EEPROM_N_EDGES; | |
| /* Don't do boundaries check because we | |
| * might have more that one bands defined | |
| * for this mode */ | |
| /* Get the edge power that's closer to our | |
| * frequency */ | |
| for (i = 0; i < AR5K_EEPROM_N_EDGES; i++) { | |
| rep_idx += i; | |
| if (target <= rep[rep_idx].freq) | |
| edge_pwr = (s16) rep[rep_idx].edge; | |
| } | |
| if (edge_pwr) | |
| ah->ah_txpower.txp_max_pwr = 4*min(edge_pwr, max_chan_pwr); | |
| } | |
| /* | |
| * Power to PCDAC table functions | |
| */ | |
| /* | |
| * Fill Power to PCDAC table on RF5111 | |
| * | |
| * No further processing is needed for RF5111, the only thing we have to | |
| * do is fill the values below and above calibration range since eeprom data | |
| * may not cover the entire PCDAC table. | |
| */ | |
| static void | |
| ath5k_fill_pwr_to_pcdac_table(struct ath5k_hw *ah, s16* table_min, | |
| s16 *table_max) | |
| { | |
| u8 *pcdac_out = ah->ah_txpower.txp_pd_table; | |
| u8 *pcdac_tmp = ah->ah_txpower.tmpL[0]; | |
| u8 pcdac_0, pcdac_n, pcdac_i, pwr_idx, i; | |
| s16 min_pwr, max_pwr; | |
| /* Get table boundaries */ | |
| min_pwr = table_min[0]; | |
| pcdac_0 = pcdac_tmp[0]; | |
| max_pwr = table_max[0]; | |
| pcdac_n = pcdac_tmp[table_max[0] - table_min[0]]; | |
| /* Extrapolate below minimum using pcdac_0 */ | |
| pcdac_i = 0; | |
| for (i = 0; i < min_pwr; i++) | |
| pcdac_out[pcdac_i++] = pcdac_0; | |
| /* Copy values from pcdac_tmp */ | |
| pwr_idx = min_pwr; | |
| for (i = 0 ; pwr_idx <= max_pwr && | |
| pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE; i++) { | |
| pcdac_out[pcdac_i++] = pcdac_tmp[i]; | |
| pwr_idx++; | |
| } | |
| /* Extrapolate above maximum */ | |
| while (pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE) | |
| pcdac_out[pcdac_i++] = pcdac_n; | |
| } | |
| /* | |
| * Combine available XPD Curves and fill Linear Power to PCDAC table | |
| * on RF5112 | |
| * | |
| * RFX112 can have up to 2 curves (one for low txpower range and one for | |
| * higher txpower range). We need to put them both on pcdac_out and place | |
| * them in the correct location. In case we only have one curve available | |
| * just fit it on pcdac_out (it's supposed to cover the entire range of | |
| * available pwr levels since it's always the higher power curve). Extrapolate | |
| * below and above final table if needed. | |
| */ | |
| static void | |
| ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min, | |
| s16 *table_max, u8 pdcurves) | |
| { | |
| u8 *pcdac_out = ah->ah_txpower.txp_pd_table; | |
| u8 *pcdac_low_pwr; | |
| u8 *pcdac_high_pwr; | |
| u8 *pcdac_tmp; | |
| u8 pwr; | |
| s16 max_pwr_idx; | |
| s16 min_pwr_idx; | |
| s16 mid_pwr_idx = 0; | |
| /* Edge flag turs on the 7nth bit on the PCDAC | |
| * to delcare the higher power curve (force values | |
| * to be greater than 64). If we only have one curve | |
| * we don't need to set this, if we have 2 curves and | |
| * fill the table backwards this can also be used to | |
| * switch from higher power curve to lower power curve */ | |
| u8 edge_flag; | |
| int i; | |
| /* When we have only one curve available | |
| * that's the higher power curve. If we have | |
| * two curves the first is the high power curve | |
| * and the next is the low power curve. */ | |
| if (pdcurves > 1) { | |
| pcdac_low_pwr = ah->ah_txpower.tmpL[1]; | |
| pcdac_high_pwr = ah->ah_txpower.tmpL[0]; | |
| mid_pwr_idx = table_max[1] - table_min[1] - 1; | |
| max_pwr_idx = (table_max[0] - table_min[0]) / 2; | |
| /* If table size goes beyond 31.5dB, keep the | |
| * upper 31.5dB range when setting tx power. | |
| * Note: 126 = 31.5 dB in quarter dB steps */ | |
| if (table_max[0] - table_min[1] > 126) | |
| min_pwr_idx = table_max[0] - 126; | |
| else | |
| min_pwr_idx = table_min[1]; | |
| /* Since we fill table backwards | |
| * start from high power curve */ | |
| pcdac_tmp = pcdac_high_pwr; | |
| edge_flag = 0x40; | |
| #if 0 | |
| /* If both min and max power limits are in lower | |
| * power curve's range, only use the low power curve. | |
| * TODO: min/max levels are related to target | |
| * power values requested from driver/user | |
| * XXX: Is this really needed ? */ | |
| if (min_pwr < table_max[1] && | |
| max_pwr < table_max[1]) { | |
| edge_flag = 0; | |
| pcdac_tmp = pcdac_low_pwr; | |
| max_pwr_idx = (table_max[1] - table_min[1])/2; | |
| } | |
| #endif | |
| } else { | |
| pcdac_low_pwr = ah->ah_txpower.tmpL[1]; /* Zeroed */ | |
| pcdac_high_pwr = ah->ah_txpower.tmpL[0]; | |
| min_pwr_idx = table_min[0]; | |
| max_pwr_idx = (table_max[0] - table_min[0]) / 2; | |
| pcdac_tmp = pcdac_high_pwr; | |
| edge_flag = 0; | |
| } | |
| /* This is used when setting tx power*/ | |
| ah->ah_txpower.txp_min_idx = min_pwr_idx/2; | |
| /* Fill Power to PCDAC table backwards */ | |
| pwr = max_pwr_idx; | |
| for (i = 63; i >= 0; i--) { | |
| /* Entering lower power range, reset | |
| * edge flag and set pcdac_tmp to lower | |
| * power curve.*/ | |
| if (edge_flag == 0x40 && | |
| (2*pwr <= (table_max[1] - table_min[0]) || pwr == 0)) { | |
| edge_flag = 0x00; | |
| pcdac_tmp = pcdac_low_pwr; | |
| pwr = mid_pwr_idx/2; | |
| } | |
| /* Don't go below 1, extrapolate below if we have | |
| * already swithced to the lower power curve -or | |
| * we only have one curve and edge_flag is zero | |
| * anyway */ | |
| if (pcdac_tmp[pwr] < 1 && (edge_flag == 0x00)) { | |
| while (i >= 0) { | |
| pcdac_out[i] = pcdac_out[i + 1]; | |
| i--; | |
| } | |
| break; | |
| } | |
| pcdac_out[i] = pcdac_tmp[pwr] | edge_flag; | |
| /* Extrapolate above if pcdac is greater than | |
| * 126 -this can happen because we OR pcdac_out | |
| * value with edge_flag on high power curve */ | |
| if (pcdac_out[i] > 126) | |
| pcdac_out[i] = 126; | |
| /* Decrease by a 0.5dB step */ | |
| pwr--; | |
| } | |
| } | |
| /* Write PCDAC values on hw */ | |
| static void | |
| ath5k_setup_pcdac_table(struct ath5k_hw *ah) | |
| { | |
| u8 *pcdac_out = ah->ah_txpower.txp_pd_table; | |
| int i; | |
| /* | |
| * Write TX power values | |
| */ | |
| for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) { | |
| ath5k_hw_reg_write(ah, | |
| (((pcdac_out[2*i + 0] << 8 | 0xff) & 0xffff) << 0) | | |
| (((pcdac_out[2*i + 1] << 8 | 0xff) & 0xffff) << 16), | |
| AR5K_PHY_PCDAC_TXPOWER(i)); | |
| } | |
| } | |
| /* | |
| * Power to PDADC table functions | |
| */ | |
| /* | |
| * Set the gain boundaries and create final Power to PDADC table | |
| * | |
| * We can have up to 4 pd curves, we need to do a simmilar process | |
| * as we do for RF5112. This time we don't have an edge_flag but we | |
| * set the gain boundaries on a separate register. | |
| */ | |
| static void | |
| ath5k_combine_pwr_to_pdadc_curves(struct ath5k_hw *ah, | |
| s16 *pwr_min, s16 *pwr_max, u8 pdcurves) | |
| { | |
| u8 gain_boundaries[AR5K_EEPROM_N_PD_GAINS]; | |
| u8 *pdadc_out = ah->ah_txpower.txp_pd_table; | |
| u8 *pdadc_tmp; | |
| s16 pdadc_0; | |
| u8 pdadc_i, pdadc_n, pwr_step, pdg, max_idx, table_size; | |
| u8 pd_gain_overlap; | |
| /* Note: Register value is initialized on initvals | |
| * there is no feedback from hw. | |
| * XXX: What about pd_gain_overlap from EEPROM ? */ | |
| pd_gain_overlap = (u8) ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG5) & | |
| AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP; | |
| /* Create final PDADC table */ | |
| for (pdg = 0, pdadc_i = 0; pdg < pdcurves; pdg++) { | |
| pdadc_tmp = ah->ah_txpower.tmpL[pdg]; | |
| if (pdg == pdcurves - 1) | |
| /* 2 dB boundary stretch for last | |
| * (higher power) curve */ | |
| gain_boundaries[pdg] = pwr_max[pdg] + 4; | |
| else | |
| /* Set gain boundary in the middle | |
| * between this curve and the next one */ | |
| gain_boundaries[pdg] = | |
| (pwr_max[pdg] + pwr_min[pdg + 1]) / 2; | |
| /* Sanity check in case our 2 db stretch got out of | |
| * range. */ | |
| if (gain_boundaries[pdg] > AR5K_TUNE_MAX_TXPOWER) | |
| gain_boundaries[pdg] = AR5K_TUNE_MAX_TXPOWER; | |
| /* For the first curve (lower power) | |
| * start from 0 dB */ | |
| if (pdg == 0) | |
| pdadc_0 = 0; | |
| else | |
| /* For the other curves use the gain overlap */ | |
| pdadc_0 = (gain_boundaries[pdg - 1] - pwr_min[pdg]) - | |
| pd_gain_overlap; | |
| /* Force each power step to be at least 0.5 dB */ | |
| if ((pdadc_tmp[1] - pdadc_tmp[0]) > 1) | |
| pwr_step = pdadc_tmp[1] - pdadc_tmp[0]; | |
| else | |
| pwr_step = 1; | |
| /* If pdadc_0 is negative, we need to extrapolate | |
| * below this pdgain by a number of pwr_steps */ | |
| while ((pdadc_0 < 0) && (pdadc_i < 128)) { | |
| s16 tmp = pdadc_tmp[0] + pdadc_0 * pwr_step; | |
| pdadc_out[pdadc_i++] = (tmp < 0) ? 0 : (u8) tmp; | |
| pdadc_0++; | |
| } | |
| /* Set last pwr level, using gain boundaries */ | |
| pdadc_n = gain_boundaries[pdg] + pd_gain_overlap - pwr_min[pdg]; | |
| /* Limit it to be inside pwr range */ | |
| table_size = pwr_max[pdg] - pwr_min[pdg]; | |
| max_idx = (pdadc_n < table_size) ? pdadc_n : table_size; | |
| /* Fill pdadc_out table */ | |
| while (pdadc_0 < max_idx) | |
| pdadc_out[pdadc_i++] = pdadc_tmp[pdadc_0++]; | |
| /* Need to extrapolate above this pdgain? */ | |
| if (pdadc_n <= max_idx) | |
| continue; | |
| /* Force each power step to be at least 0.5 dB */ | |
| if ((pdadc_tmp[table_size - 1] - pdadc_tmp[table_size - 2]) > 1) | |
| pwr_step = pdadc_tmp[table_size - 1] - | |
| pdadc_tmp[table_size - 2]; | |
| else | |
| pwr_step = 1; | |
| /* Extrapolate above */ | |
| while ((pdadc_0 < (s16) pdadc_n) && | |
| (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2)) { | |
| s16 tmp = pdadc_tmp[table_size - 1] + | |
| (pdadc_0 - max_idx) * pwr_step; | |
| pdadc_out[pdadc_i++] = (tmp > 127) ? 127 : (u8) tmp; | |
| pdadc_0++; | |
| } | |
| } | |
| while (pdg < AR5K_EEPROM_N_PD_GAINS) { | |
| gain_boundaries[pdg] = gain_boundaries[pdg - 1]; | |
| pdg++; | |
| } | |
| while (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2) { | |
| pdadc_out[pdadc_i] = pdadc_out[pdadc_i - 1]; | |
| pdadc_i++; | |
| } | |
| /* Set gain boundaries */ | |
| ath5k_hw_reg_write(ah, | |
| AR5K_REG_SM(pd_gain_overlap, | |
| AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP) | | |
| AR5K_REG_SM(gain_boundaries[0], | |
| AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_1) | | |
| AR5K_REG_SM(gain_boundaries[1], | |
| AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_2) | | |
| AR5K_REG_SM(gain_boundaries[2], | |
| AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_3) | | |
| AR5K_REG_SM(gain_boundaries[3], | |
| AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_4), | |
| AR5K_PHY_TPC_RG5); | |
| /* Used for setting rate power table */ | |
| ah->ah_txpower.txp_min_idx = pwr_min[0]; | |
| } | |
| /* Write PDADC values on hw */ | |
| static void | |
| ath5k_setup_pwr_to_pdadc_table(struct ath5k_hw *ah, | |
| u8 pdcurves, u8 *pdg_to_idx) | |
| { | |
| u8 *pdadc_out = ah->ah_txpower.txp_pd_table; | |
| u32 reg; | |
| u8 i; | |
| /* Select the right pdgain curves */ | |
| /* Clear current settings */ | |
| reg = ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG1); | |
| reg &= ~(AR5K_PHY_TPC_RG1_PDGAIN_1 | | |
| AR5K_PHY_TPC_RG1_PDGAIN_2 | | |
| AR5K_PHY_TPC_RG1_PDGAIN_3 | | |
| AR5K_PHY_TPC_RG1_NUM_PD_GAIN); | |
| /* | |
| * Use pd_gains curve from eeprom | |
| * | |
| * This overrides the default setting from initvals | |
| * in case some vendors (e.g. Zcomax) don't use the default | |
| * curves. If we don't honor their settings we 'll get a | |
| * 5dB (1 * gain overlap ?) drop. | |
| */ | |
| reg |= AR5K_REG_SM(pdcurves, AR5K_PHY_TPC_RG1_NUM_PD_GAIN); | |
| switch (pdcurves) { | |
| case 3: | |
| reg |= AR5K_REG_SM(pdg_to_idx[2], AR5K_PHY_TPC_RG1_PDGAIN_3); | |
| /* Fall through */ | |
| case 2: | |
| reg |= AR5K_REG_SM(pdg_to_idx[1], AR5K_PHY_TPC_RG1_PDGAIN_2); | |
| /* Fall through */ | |
| case 1: | |
| reg |= AR5K_REG_SM(pdg_to_idx[0], AR5K_PHY_TPC_RG1_PDGAIN_1); | |
| break; | |
| } | |
| ath5k_hw_reg_write(ah, reg, AR5K_PHY_TPC_RG1); | |
| /* | |
| * Write TX power values | |
| */ | |
| for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) { | |
| ath5k_hw_reg_write(ah, | |
| ((pdadc_out[4*i + 0] & 0xff) << 0) | | |
| ((pdadc_out[4*i + 1] & 0xff) << 8) | | |
| ((pdadc_out[4*i + 2] & 0xff) << 16) | | |
| ((pdadc_out[4*i + 3] & 0xff) << 24), | |
| AR5K_PHY_PDADC_TXPOWER(i)); | |
| } | |
| } | |
| /* | |
| * Common code for PCDAC/PDADC tables | |
| */ | |
| /* | |
| * This is the main function that uses all of the above | |
| * to set PCDAC/PDADC table on hw for the current channel. | |
| * This table is used for tx power calibration on the basband, | |
| * without it we get weird tx power levels and in some cases | |
| * distorted spectral mask | |
| */ | |
| static int | |
| ath5k_setup_channel_powertable(struct ath5k_hw *ah, | |
| struct ieee80211_channel *channel, | |
| u8 ee_mode, u8 type) | |
| { | |
| struct ath5k_pdgain_info *pdg_L, *pdg_R; | |
| struct ath5k_chan_pcal_info *pcinfo_L; | |
| struct ath5k_chan_pcal_info *pcinfo_R; | |
| struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; | |
| u8 *pdg_curve_to_idx = ee->ee_pdc_to_idx[ee_mode]; | |
| s16 table_min[AR5K_EEPROM_N_PD_GAINS]; | |
| s16 table_max[AR5K_EEPROM_N_PD_GAINS]; | |
| u8 *tmpL; | |
| u8 *tmpR; | |
| u32 target = channel->center_freq; | |
| int pdg, i; | |
| /* Get surounding freq piers for this channel */ | |
| ath5k_get_chan_pcal_surrounding_piers(ah, channel, | |
| &pcinfo_L, | |
| &pcinfo_R); | |
| /* Loop over pd gain curves on | |
| * surounding freq piers by index */ | |
| for (pdg = 0; pdg < ee->ee_pd_gains[ee_mode]; pdg++) { | |
| /* Fill curves in reverse order | |
| * from lower power (max gain) | |
| * to higher power. Use curve -> idx | |
| * backmaping we did on eeprom init */ | |
| u8 idx = pdg_curve_to_idx[pdg]; | |
| /* Grab the needed curves by index */ | |
| pdg_L = &pcinfo_L->pd_curves[idx]; | |
| pdg_R = &pcinfo_R->pd_curves[idx]; | |
| /* Initialize the temp tables */ | |
| tmpL = ah->ah_txpower.tmpL[pdg]; | |
| tmpR = ah->ah_txpower.tmpR[pdg]; | |
| /* Set curve's x boundaries and create | |
| * curves so that they cover the same | |
| * range (if we don't do that one table | |
| * will have values on some range and the | |
| * other one won't have any so interpolation | |
| * will fail) */ | |
| table_min[pdg] = min(pdg_L->pd_pwr[0], | |
| pdg_R->pd_pwr[0]) / 2; | |
| table_max[pdg] = max(pdg_L->pd_pwr[pdg_L->pd_points - 1], | |
| pdg_R->pd_pwr[pdg_R->pd_points - 1]) / 2; | |
| /* Now create the curves on surrounding channels | |
| * and interpolate if needed to get the final | |
| * curve for this gain on this channel */ | |
| switch (type) { | |
| case AR5K_PWRTABLE_LINEAR_PCDAC: | |
| /* Override min/max so that we don't loose | |
| * accuracy (don't divide by 2) */ | |
| table_min[pdg] = min(pdg_L->pd_pwr[0], | |
| pdg_R->pd_pwr[0]); | |
| table_max[pdg] = | |
| max(pdg_L->pd_pwr[pdg_L->pd_points - 1], | |
| pdg_R->pd_pwr[pdg_R->pd_points - 1]); | |
| /* Override minimum so that we don't get | |
| * out of bounds while extrapolating | |
| * below. Don't do this when we have 2 | |
| * curves and we are on the high power curve | |
| * because table_min is ok in this case */ | |
| if (!(ee->ee_pd_gains[ee_mode] > 1 && pdg == 0)) { | |
| table_min[pdg] = | |
| ath5k_get_linear_pcdac_min(pdg_L->pd_step, | |
| pdg_R->pd_step, | |
| pdg_L->pd_pwr, | |
| pdg_R->pd_pwr); | |
| /* Don't go too low because we will | |
| * miss the upper part of the curve. | |
| * Note: 126 = 31.5dB (max power supported) | |
| * in 0.25dB units */ | |
| if (table_max[pdg] - table_min[pdg] > 126) | |
| table_min[pdg] = table_max[pdg] - 126; | |
| } | |
| /* Fall through */ | |
| case AR5K_PWRTABLE_PWR_TO_PCDAC: | |
| case AR5K_PWRTABLE_PWR_TO_PDADC: | |
| ath5k_create_power_curve(table_min[pdg], | |
| table_max[pdg], | |
| pdg_L->pd_pwr, | |
| pdg_L->pd_step, | |
| pdg_L->pd_points, tmpL, type); | |
| /* We are in a calibration | |
| * pier, no need to interpolate | |
| * between freq piers */ | |
| if (pcinfo_L == pcinfo_R) | |
| continue; | |
| ath5k_create_power_curve(table_min[pdg], | |
| table_max[pdg], | |
| pdg_R->pd_pwr, | |
| pdg_R->pd_step, | |
| pdg_R->pd_points, tmpR, type); | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| /* Interpolate between curves | |
| * of surounding freq piers to | |
| * get the final curve for this | |
| * pd gain. Re-use tmpL for interpolation | |
| * output */ | |
| for (i = 0; (i < (u16) (table_max[pdg] - table_min[pdg])) && | |
| (i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) { | |
| tmpL[i] = (u8) ath5k_get_interpolated_value(target, | |
| (s16) pcinfo_L->freq, | |
| (s16) pcinfo_R->freq, | |
| (s16) tmpL[i], | |
| (s16) tmpR[i]); | |
| } | |
| } | |
| /* Now we have a set of curves for this | |
| * channel on tmpL (x range is table_max - table_min | |
| * and y values are tmpL[pdg][]) sorted in the same | |
| * order as EEPROM (because we've used the backmaping). | |
| * So for RF5112 it's from higher power to lower power | |
| * and for RF2413 it's from lower power to higher power. | |
| * For RF5111 we only have one curve. */ | |
| /* Fill min and max power levels for this | |
| * channel by interpolating the values on | |
| * surounding channels to complete the dataset */ | |
| ah->ah_txpower.txp_min_pwr = ath5k_get_interpolated_value(target, | |
| (s16) pcinfo_L->freq, | |
| (s16) pcinfo_R->freq, | |
| pcinfo_L->min_pwr, pcinfo_R->min_pwr); | |
| ah->ah_txpower.txp_max_pwr = ath5k_get_interpolated_value(target, | |
| (s16) pcinfo_L->freq, | |
| (s16) pcinfo_R->freq, | |
| pcinfo_L->max_pwr, pcinfo_R->max_pwr); | |
| /* We are ready to go, fill PCDAC/PDADC | |
| * table and write settings on hardware */ | |
| switch (type) { | |
| case AR5K_PWRTABLE_LINEAR_PCDAC: | |
| /* For RF5112 we can have one or two curves | |
| * and each curve covers a certain power lvl | |
| * range so we need to do some more processing */ | |
| ath5k_combine_linear_pcdac_curves(ah, table_min, table_max, | |
| ee->ee_pd_gains[ee_mode]); | |
| /* Set txp.offset so that we can | |
| * match max power value with max | |
| * table index */ | |
| ah->ah_txpower.txp_offset = 64 - (table_max[0] / 2); | |
| /* Write settings on hw */ | |
| ath5k_setup_pcdac_table(ah); | |
| break; | |
| case AR5K_PWRTABLE_PWR_TO_PCDAC: | |
| /* We are done for RF5111 since it has only | |
| * one curve, just fit the curve on the table */ | |
| ath5k_fill_pwr_to_pcdac_table(ah, table_min, table_max); | |
| /* No rate powertable adjustment for RF5111 */ | |
| ah->ah_txpower.txp_min_idx = 0; | |
| ah->ah_txpower.txp_offset = 0; | |
| /* Write settings on hw */ | |
| ath5k_setup_pcdac_table(ah); | |
| break; | |
| case AR5K_PWRTABLE_PWR_TO_PDADC: | |
| /* Set PDADC boundaries and fill | |
| * final PDADC table */ | |
| ath5k_combine_pwr_to_pdadc_curves(ah, table_min, table_max, | |
| ee->ee_pd_gains[ee_mode]); | |
| /* Write settings on hw */ | |
| ath5k_setup_pwr_to_pdadc_table(ah, pdg, pdg_curve_to_idx); | |
| /* Set txp.offset, note that table_min | |
| * can be negative */ | |
| ah->ah_txpower.txp_offset = table_min[0]; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| /* | |
| * Per-rate tx power setting | |
| * | |
| * This is the code that sets the desired tx power (below | |
| * maximum) on hw for each rate (we also have TPC that sets | |
| * power per packet). We do that by providing an index on the | |
| * PCDAC/PDADC table we set up. | |
| */ | |
| /* | |
| * Set rate power table | |
| * | |
| * For now we only limit txpower based on maximum tx power | |
| * supported by hw (what's inside rate_info). We need to limit | |
| * this even more, based on regulatory domain etc. | |
| * | |
| * Rate power table contains indices to PCDAC/PDADC table (0.5dB steps) | |
| * and is indexed as follows: | |
| * rates[0] - rates[7] -> OFDM rates | |
| * rates[8] - rates[14] -> CCK rates | |
| * rates[15] -> XR rates (they all have the same power) | |
| */ | |
| static void | |
| ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr, | |
| struct ath5k_rate_pcal_info *rate_info, | |
| u8 ee_mode) | |
| { | |
| unsigned int i; | |
| u16 *rates; | |
| /* max_pwr is power level we got from driver/user in 0.5dB | |
| * units, switch to 0.25dB units so we can compare */ | |
| max_pwr *= 2; | |
| max_pwr = min(max_pwr, (u16) ah->ah_txpower.txp_max_pwr) / 2; | |
| /* apply rate limits */ | |
| rates = ah->ah_txpower.txp_rates_power_table; | |
| /* OFDM rates 6 to 24Mb/s */ | |
| for (i = 0; i < 5; i++) | |
| rates[i] = min(max_pwr, rate_info->target_power_6to24); | |
| /* Rest OFDM rates */ | |
| rates[5] = min(rates[0], rate_info->target_power_36); | |
| rates[6] = min(rates[0], rate_info->target_power_48); | |
| rates[7] = min(rates[0], rate_info->target_power_54); | |
| /* CCK rates */ | |
| /* 1L */ | |
| rates[8] = min(rates[0], rate_info->target_power_6to24); | |
| /* 2L */ | |
| rates[9] = min(rates[0], rate_info->target_power_36); | |
| /* 2S */ | |
| rates[10] = min(rates[0], rate_info->target_power_36); | |
| /* 5L */ | |
| rates[11] = min(rates[0], rate_info->target_power_48); | |
| /* 5S */ | |
| rates[12] = min(rates[0], rate_info->target_power_48); | |
| /* 11L */ | |
| rates[13] = min(rates[0], rate_info->target_power_54); | |
| /* 11S */ | |
| rates[14] = min(rates[0], rate_info->target_power_54); | |
| /* XR rates */ | |
| rates[15] = min(rates[0], rate_info->target_power_6to24); | |
| /* CCK rates have different peak to average ratio | |
| * so we have to tweak their power so that gainf | |
| * correction works ok. For this we use OFDM to | |
| * CCK delta from eeprom */ | |
| if ((ee_mode == AR5K_EEPROM_MODE_11G) && | |
| (ah->ah_phy_revision < AR5K_SREV_PHY_5212A)) | |
| for (i = 8; i <= 15; i++) | |
| rates[i] -= ah->ah_txpower.txp_cck_ofdm_gainf_delta; | |
| ah->ah_txpower.txp_min_pwr = rates[7]; | |
| ah->ah_txpower.txp_max_pwr = rates[0]; | |
| ah->ah_txpower.txp_ofdm = rates[7]; | |
| } | |
| /* | |
| * Set transmition power | |
| */ | |
| int | |
| ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, | |
| u8 ee_mode, u8 txpower) | |
| { | |
| struct ath5k_rate_pcal_info rate_info; | |
| u8 type; | |
| int ret; | |
| ATH5K_TRACE(ah->ah_sc); | |
| if (txpower > AR5K_TUNE_MAX_TXPOWER) { | |
| ATH5K_ERR(ah->ah_sc, "invalid tx power: %u\n", txpower); | |
| return -EINVAL; | |
| } | |
| if (txpower == 0) | |
| txpower = AR5K_TUNE_DEFAULT_TXPOWER; | |
| /* Reset TX power values */ | |
| memset(&ah->ah_txpower, 0, sizeof(ah->ah_txpower)); | |
| ah->ah_txpower.txp_tpc = AR5K_TUNE_TPC_TXPOWER; | |
| ah->ah_txpower.txp_min_pwr = 0; | |
| ah->ah_txpower.txp_max_pwr = AR5K_TUNE_MAX_TXPOWER; | |
| /* Initialize TX power table */ | |
| switch (ah->ah_radio) { | |
| case AR5K_RF5111: | |
| type = AR5K_PWRTABLE_PWR_TO_PCDAC; | |
| break; | |
| case AR5K_RF5112: | |
| type = AR5K_PWRTABLE_LINEAR_PCDAC; | |
| break; | |
| case AR5K_RF2413: | |
| case AR5K_RF5413: | |
| case AR5K_RF2316: | |
| case AR5K_RF2317: | |
| case AR5K_RF2425: | |
| type = AR5K_PWRTABLE_PWR_TO_PDADC; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| /* FIXME: Only on channel/mode change */ | |
| ret = ath5k_setup_channel_powertable(ah, channel, ee_mode, type); | |
| if (ret) | |
| return ret; | |
| /* Limit max power if we have a CTL available */ | |
| ath5k_get_max_ctl_power(ah, channel); | |
| /* FIXME: Tx power limit for this regdomain | |
| * XXX: Mac80211/CRDA will do that anyway ? */ | |
| /* FIXME: Antenna reduction stuff */ | |
| /* FIXME: Limit power on turbo modes */ | |
| /* FIXME: TPC scale reduction */ | |
| /* Get surounding channels for per-rate power table | |
| * calibration */ | |
| ath5k_get_rate_pcal_data(ah, channel, &rate_info); | |
| /* Setup rate power table */ | |
| ath5k_setup_rate_powertable(ah, txpower, &rate_info, ee_mode); | |
| /* Write rate power table on hw */ | |
| ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(3, 24) | | |
| AR5K_TXPOWER_OFDM(2, 16) | AR5K_TXPOWER_OFDM(1, 8) | | |
| AR5K_TXPOWER_OFDM(0, 0), AR5K_PHY_TXPOWER_RATE1); | |
| ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(7, 24) | | |
| AR5K_TXPOWER_OFDM(6, 16) | AR5K_TXPOWER_OFDM(5, 8) | | |
| AR5K_TXPOWER_OFDM(4, 0), AR5K_PHY_TXPOWER_RATE2); | |
| ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(10, 24) | | |
| AR5K_TXPOWER_CCK(9, 16) | AR5K_TXPOWER_CCK(15, 8) | | |
| AR5K_TXPOWER_CCK(8, 0), AR5K_PHY_TXPOWER_RATE3); | |
| ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(14, 24) | | |
| AR5K_TXPOWER_CCK(13, 16) | AR5K_TXPOWER_CCK(12, 8) | | |
| AR5K_TXPOWER_CCK(11, 0), AR5K_PHY_TXPOWER_RATE4); | |
| /* FIXME: TPC support */ | |
| if (ah->ah_txpower.txp_tpc) { | |
| ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX_TPC_ENABLE | | |
| AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX); | |
| ath5k_hw_reg_write(ah, | |
| AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_ACK) | | |
| AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CTS) | | |
| AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CHIRP), | |
| AR5K_TPC); | |
| } else { | |
| ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX | | |
| AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX); | |
| } | |
| return 0; | |
| } | |
| int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 mode, u8 txpower) | |
| { | |
| /*Just a try M.F.*/ | |
| struct ieee80211_channel *channel = &ah->ah_current_channel; | |
| ATH5K_TRACE(ah->ah_sc); | |
| ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_TXPOWER, | |
| "changing txpower to %d\n", txpower); | |
| return ath5k_hw_txpower(ah, channel, mode, txpower); | |
| } | |
| #undef _ATH5K_PHY |