| /* | |
| * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org> | |
| * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com> | |
| * Copyright (c) 2007-2008 Matthew W. S. Bell <mentor@madwifi.org> | |
| * Copyright (c) 2007-2008 Luis Rodriguez <mcgrof@winlab.rutgers.edu> | |
| * Copyright (c) 2007-2008 Pavel Roskin <proski@gnu.org> | |
| * Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com> | |
| * | |
| * Permission to use, copy, modify, and distribute this software for any | |
| * purpose with or without fee is hereby granted, provided that the above | |
| * copyright notice and this permission notice appear in all copies. | |
| * | |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES | |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR | |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES | |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN | |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF | |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. | |
| * | |
| */ | |
| /*********************************\ | |
| * Protocol Control Unit Functions * | |
| \*********************************/ | |
| #include "ath5k.h" | |
| #include "reg.h" | |
| #include "debug.h" | |
| #include "base.h" | |
| /*******************\ | |
| * Generic functions * | |
| \*******************/ | |
| /** | |
| * ath5k_hw_set_opmode - Set PCU operating mode | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * | |
| * Initialize PCU for the various operating modes (AP/STA etc) | |
| * | |
| * NOTE: ah->ah_op_mode must be set before calling this. | |
| */ | |
| int ath5k_hw_set_opmode(struct ath5k_hw *ah) | |
| { | |
| u32 pcu_reg, beacon_reg, low_id, high_id; | |
| /* Preserve rest settings */ | |
| pcu_reg = ath5k_hw_reg_read(ah, AR5K_STA_ID1) & 0xffff0000; | |
| pcu_reg &= ~(AR5K_STA_ID1_ADHOC | AR5K_STA_ID1_AP | |
| | AR5K_STA_ID1_KEYSRCH_MODE | |
| | (ah->ah_version == AR5K_AR5210 ? | |
| (AR5K_STA_ID1_PWR_SV | AR5K_STA_ID1_NO_PSPOLL) : 0)); | |
| beacon_reg = 0; | |
| ATH5K_TRACE(ah->ah_sc); | |
| switch (ah->ah_op_mode) { | |
| case NL80211_IFTYPE_ADHOC: | |
| pcu_reg |= AR5K_STA_ID1_ADHOC | AR5K_STA_ID1_KEYSRCH_MODE; | |
| beacon_reg |= AR5K_BCR_ADHOC; | |
| if (ah->ah_version == AR5K_AR5210) | |
| pcu_reg |= AR5K_STA_ID1_NO_PSPOLL; | |
| else | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_CFG, AR5K_CFG_IBSS); | |
| break; | |
| case NL80211_IFTYPE_AP: | |
| case NL80211_IFTYPE_MESH_POINT: | |
| pcu_reg |= AR5K_STA_ID1_AP | AR5K_STA_ID1_KEYSRCH_MODE; | |
| beacon_reg |= AR5K_BCR_AP; | |
| if (ah->ah_version == AR5K_AR5210) | |
| pcu_reg |= AR5K_STA_ID1_NO_PSPOLL; | |
| else | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_CFG, AR5K_CFG_IBSS); | |
| break; | |
| case NL80211_IFTYPE_STATION: | |
| pcu_reg |= AR5K_STA_ID1_KEYSRCH_MODE | |
| | (ah->ah_version == AR5K_AR5210 ? | |
| AR5K_STA_ID1_PWR_SV : 0); | |
| case NL80211_IFTYPE_MONITOR: | |
| pcu_reg |= AR5K_STA_ID1_KEYSRCH_MODE | |
| | (ah->ah_version == AR5K_AR5210 ? | |
| AR5K_STA_ID1_NO_PSPOLL : 0); | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| /* | |
| * Set PCU registers | |
| */ | |
| low_id = AR5K_LOW_ID(ah->ah_sta_id); | |
| high_id = AR5K_HIGH_ID(ah->ah_sta_id); | |
| ath5k_hw_reg_write(ah, low_id, AR5K_STA_ID0); | |
| ath5k_hw_reg_write(ah, pcu_reg | high_id, AR5K_STA_ID1); | |
| /* | |
| * Set Beacon Control Register on 5210 | |
| */ | |
| if (ah->ah_version == AR5K_AR5210) | |
| ath5k_hw_reg_write(ah, beacon_reg, AR5K_BCR); | |
| return 0; | |
| } | |
| /** | |
| * ath5k_hw_update - Update mib counters (mac layer statistics) | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @stats: The &struct ieee80211_low_level_stats we use to track | |
| * statistics on the driver | |
| * | |
| * Reads MIB counters from PCU and updates sw statistics. Must be | |
| * called after a MIB interrupt. | |
| */ | |
| void ath5k_hw_update_mib_counters(struct ath5k_hw *ah, | |
| struct ieee80211_low_level_stats *stats) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Read-And-Clear */ | |
| stats->dot11ACKFailureCount += ath5k_hw_reg_read(ah, AR5K_ACK_FAIL); | |
| stats->dot11RTSFailureCount += ath5k_hw_reg_read(ah, AR5K_RTS_FAIL); | |
| stats->dot11RTSSuccessCount += ath5k_hw_reg_read(ah, AR5K_RTS_OK); | |
| stats->dot11FCSErrorCount += ath5k_hw_reg_read(ah, AR5K_FCS_FAIL); | |
| /* XXX: Should we use this to track beacon count ? | |
| * -we read it anyway to clear the register */ | |
| ath5k_hw_reg_read(ah, AR5K_BEACON_CNT); | |
| /* Reset profile count registers on 5212*/ | |
| if (ah->ah_version == AR5K_AR5212) { | |
| ath5k_hw_reg_write(ah, 0, AR5K_PROFCNT_TX); | |
| ath5k_hw_reg_write(ah, 0, AR5K_PROFCNT_RX); | |
| ath5k_hw_reg_write(ah, 0, AR5K_PROFCNT_RXCLR); | |
| ath5k_hw_reg_write(ah, 0, AR5K_PROFCNT_CYCLE); | |
| } | |
| /* TODO: Handle ANI stats */ | |
| } | |
| /** | |
| * ath5k_hw_set_ack_bitrate - set bitrate for ACKs | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @high: Flag to determine if we want to use high transmition rate | |
| * for ACKs or not | |
| * | |
| * If high flag is set, we tell hw to use a set of control rates based on | |
| * the current transmition rate (check out control_rates array inside reset.c). | |
| * If not hw just uses the lowest rate available for the current modulation | |
| * scheme being used (1Mbit for CCK and 6Mbits for OFDM). | |
| */ | |
| void ath5k_hw_set_ack_bitrate_high(struct ath5k_hw *ah, bool high) | |
| { | |
| if (ah->ah_version != AR5K_AR5212) | |
| return; | |
| else { | |
| u32 val = AR5K_STA_ID1_BASE_RATE_11B | AR5K_STA_ID1_ACKCTS_6MB; | |
| if (high) | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_STA_ID1, val); | |
| else | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_STA_ID1, val); | |
| } | |
| } | |
| /******************\ | |
| * ACK/CTS Timeouts * | |
| \******************/ | |
| /** | |
| * ath5k_hw_het_ack_timeout - Get ACK timeout from PCU in usec | |
| * | |
| * @ah: The &struct ath5k_hw | |
| */ | |
| unsigned int ath5k_hw_get_ack_timeout(struct ath5k_hw *ah) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| return ath5k_hw_clocktoh(AR5K_REG_MS(ath5k_hw_reg_read(ah, | |
| AR5K_TIME_OUT), AR5K_TIME_OUT_ACK), ah->ah_turbo); | |
| } | |
| /** | |
| * ath5k_hw_set_ack_timeout - Set ACK timeout on PCU | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @timeout: Timeout in usec | |
| */ | |
| int ath5k_hw_set_ack_timeout(struct ath5k_hw *ah, unsigned int timeout) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| if (ath5k_hw_clocktoh(AR5K_REG_MS(0xffffffff, AR5K_TIME_OUT_ACK), | |
| ah->ah_turbo) <= timeout) | |
| return -EINVAL; | |
| AR5K_REG_WRITE_BITS(ah, AR5K_TIME_OUT, AR5K_TIME_OUT_ACK, | |
| ath5k_hw_htoclock(timeout, ah->ah_turbo)); | |
| return 0; | |
| } | |
| /** | |
| * ath5k_hw_get_cts_timeout - Get CTS timeout from PCU in usec | |
| * | |
| * @ah: The &struct ath5k_hw | |
| */ | |
| unsigned int ath5k_hw_get_cts_timeout(struct ath5k_hw *ah) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| return ath5k_hw_clocktoh(AR5K_REG_MS(ath5k_hw_reg_read(ah, | |
| AR5K_TIME_OUT), AR5K_TIME_OUT_CTS), ah->ah_turbo); | |
| } | |
| /** | |
| * ath5k_hw_set_cts_timeout - Set CTS timeout on PCU | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @timeout: Timeout in usec | |
| */ | |
| int ath5k_hw_set_cts_timeout(struct ath5k_hw *ah, unsigned int timeout) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| if (ath5k_hw_clocktoh(AR5K_REG_MS(0xffffffff, AR5K_TIME_OUT_CTS), | |
| ah->ah_turbo) <= timeout) | |
| return -EINVAL; | |
| AR5K_REG_WRITE_BITS(ah, AR5K_TIME_OUT, AR5K_TIME_OUT_CTS, | |
| ath5k_hw_htoclock(timeout, ah->ah_turbo)); | |
| return 0; | |
| } | |
| /****************\ | |
| * BSSID handling * | |
| \****************/ | |
| /** | |
| * ath5k_hw_get_lladdr - Get station id | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @mac: The card's mac address | |
| * | |
| * Initialize ah->ah_sta_id using the mac address provided | |
| * (just a memcpy). | |
| * | |
| * TODO: Remove it once we merge ath5k_softc and ath5k_hw | |
| */ | |
| void ath5k_hw_get_lladdr(struct ath5k_hw *ah, u8 *mac) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| memcpy(mac, ah->ah_sta_id, ETH_ALEN); | |
| } | |
| /** | |
| * ath5k_hw_set_lladdr - Set station id | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @mac: The card's mac address | |
| * | |
| * Set station id on hw using the provided mac address | |
| */ | |
| int ath5k_hw_set_lladdr(struct ath5k_hw *ah, const u8 *mac) | |
| { | |
| u32 low_id, high_id; | |
| u32 pcu_reg; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Set new station ID */ | |
| memcpy(ah->ah_sta_id, mac, ETH_ALEN); | |
| pcu_reg = ath5k_hw_reg_read(ah, AR5K_STA_ID1) & 0xffff0000; | |
| low_id = AR5K_LOW_ID(mac); | |
| high_id = AR5K_HIGH_ID(mac); | |
| ath5k_hw_reg_write(ah, low_id, AR5K_STA_ID0); | |
| ath5k_hw_reg_write(ah, pcu_reg | high_id, AR5K_STA_ID1); | |
| return 0; | |
| } | |
| /** | |
| * ath5k_hw_set_associd - Set BSSID for association | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @bssid: BSSID | |
| * @assoc_id: Assoc id | |
| * | |
| * Sets the BSSID which trigers the "SME Join" operation | |
| */ | |
| void ath5k_hw_set_associd(struct ath5k_hw *ah, const u8 *bssid, u16 assoc_id) | |
| { | |
| u32 low_id, high_id; | |
| u16 tim_offset = 0; | |
| /* | |
| * Set simple BSSID mask on 5212 | |
| */ | |
| if (ah->ah_version == AR5K_AR5212) { | |
| ath5k_hw_reg_write(ah, AR5K_LOW_ID(ah->ah_bssid_mask), | |
| AR5K_BSS_IDM0); | |
| ath5k_hw_reg_write(ah, AR5K_HIGH_ID(ah->ah_bssid_mask), | |
| AR5K_BSS_IDM1); | |
| } | |
| /* | |
| * Set BSSID which triggers the "SME Join" operation | |
| */ | |
| low_id = AR5K_LOW_ID(bssid); | |
| high_id = AR5K_HIGH_ID(bssid); | |
| ath5k_hw_reg_write(ah, low_id, AR5K_BSS_ID0); | |
| ath5k_hw_reg_write(ah, high_id | ((assoc_id & 0x3fff) << | |
| AR5K_BSS_ID1_AID_S), AR5K_BSS_ID1); | |
| if (assoc_id == 0) { | |
| ath5k_hw_disable_pspoll(ah); | |
| return; | |
| } | |
| AR5K_REG_WRITE_BITS(ah, AR5K_BEACON, AR5K_BEACON_TIM, | |
| tim_offset ? tim_offset + 4 : 0); | |
| ath5k_hw_enable_pspoll(ah, NULL, 0); | |
| } | |
| /** | |
| * ath5k_hw_set_bssid_mask - filter out bssids we listen | |
| * | |
| * @ah: the &struct ath5k_hw | |
| * @mask: the bssid_mask, a u8 array of size ETH_ALEN | |
| * | |
| * BSSID masking is a method used by AR5212 and newer hardware to inform PCU | |
| * which bits of the interface's MAC address should be looked at when trying | |
| * to decide which packets to ACK. In station mode and AP mode with a single | |
| * BSS every bit matters since we lock to only one BSS. In AP mode with | |
| * multiple BSSes (virtual interfaces) not every bit matters because hw must | |
| * accept frames for all BSSes and so we tweak some bits of our mac address | |
| * in order to have multiple BSSes. | |
| * | |
| * NOTE: This is a simple filter and does *not* filter out all | |
| * relevant frames. Some frames that are not for us might get ACKed from us | |
| * by PCU because they just match the mask. | |
| * | |
| * When handling multiple BSSes you can get the BSSID mask by computing the | |
| * set of ~ ( MAC XOR BSSID ) for all bssids we handle. | |
| * | |
| * When you do this you are essentially computing the common bits of all your | |
| * BSSes. Later it is assumed the harware will "and" (&) the BSSID mask with | |
| * the MAC address to obtain the relevant bits and compare the result with | |
| * (frame's BSSID & mask) to see if they match. | |
| */ | |
| /* | |
| * Simple example: on your card you have have two BSSes you have created with | |
| * BSSID-01 and BSSID-02. Lets assume BSSID-01 will not use the MAC address. | |
| * There is another BSSID-03 but you are not part of it. For simplicity's sake, | |
| * assuming only 4 bits for a mac address and for BSSIDs you can then have: | |
| * | |
| * \ | |
| * MAC: 0001 | | |
| * BSSID-01: 0100 | --> Belongs to us | |
| * BSSID-02: 1001 | | |
| * / | |
| * ------------------- | |
| * BSSID-03: 0110 | --> External | |
| * ------------------- | |
| * | |
| * Our bssid_mask would then be: | |
| * | |
| * On loop iteration for BSSID-01: | |
| * ~(0001 ^ 0100) -> ~(0101) | |
| * -> 1010 | |
| * bssid_mask = 1010 | |
| * | |
| * On loop iteration for BSSID-02: | |
| * bssid_mask &= ~(0001 ^ 1001) | |
| * bssid_mask = (1010) & ~(0001 ^ 1001) | |
| * bssid_mask = (1010) & ~(1001) | |
| * bssid_mask = (1010) & (0110) | |
| * bssid_mask = 0010 | |
| * | |
| * A bssid_mask of 0010 means "only pay attention to the second least | |
| * significant bit". This is because its the only bit common | |
| * amongst the MAC and all BSSIDs we support. To findout what the real | |
| * common bit is we can simply "&" the bssid_mask now with any BSSID we have | |
| * or our MAC address (we assume the hardware uses the MAC address). | |
| * | |
| * Now, suppose there's an incoming frame for BSSID-03: | |
| * | |
| * IFRAME-01: 0110 | |
| * | |
| * An easy eye-inspeciton of this already should tell you that this frame | |
| * will not pass our check. This is beacuse the bssid_mask tells the | |
| * hardware to only look at the second least significant bit and the | |
| * common bit amongst the MAC and BSSIDs is 0, this frame has the 2nd LSB | |
| * as 1, which does not match 0. | |
| * | |
| * So with IFRAME-01 we *assume* the hardware will do: | |
| * | |
| * allow = (IFRAME-01 & bssid_mask) == (bssid_mask & MAC) ? 1 : 0; | |
| * --> allow = (0110 & 0010) == (0010 & 0001) ? 1 : 0; | |
| * --> allow = (0010) == 0000 ? 1 : 0; | |
| * --> allow = 0 | |
| * | |
| * Lets now test a frame that should work: | |
| * | |
| * IFRAME-02: 0001 (we should allow) | |
| * | |
| * allow = (0001 & 1010) == 1010 | |
| * | |
| * allow = (IFRAME-02 & bssid_mask) == (bssid_mask & MAC) ? 1 : 0; | |
| * --> allow = (0001 & 0010) == (0010 & 0001) ? 1 :0; | |
| * --> allow = (0010) == (0010) | |
| * --> allow = 1 | |
| * | |
| * Other examples: | |
| * | |
| * IFRAME-03: 0100 --> allowed | |
| * IFRAME-04: 1001 --> allowed | |
| * IFRAME-05: 1101 --> allowed but its not for us!!! | |
| * | |
| */ | |
| int ath5k_hw_set_bssid_mask(struct ath5k_hw *ah, const u8 *mask) | |
| { | |
| u32 low_id, high_id; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Cache bssid mask so that we can restore it | |
| * on reset */ | |
| memcpy(ah->ah_bssid_mask, mask, ETH_ALEN); | |
| if (ah->ah_version == AR5K_AR5212) { | |
| low_id = AR5K_LOW_ID(mask); | |
| high_id = AR5K_HIGH_ID(mask); | |
| ath5k_hw_reg_write(ah, low_id, AR5K_BSS_IDM0); | |
| ath5k_hw_reg_write(ah, high_id, AR5K_BSS_IDM1); | |
| return 0; | |
| } | |
| return -EIO; | |
| } | |
| /************\ | |
| * RX Control * | |
| \************/ | |
| /** | |
| * ath5k_hw_start_rx_pcu - Start RX engine | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * | |
| * Starts RX engine on PCU so that hw can process RXed frames | |
| * (ACK etc). | |
| * | |
| * NOTE: RX DMA should be already enabled using ath5k_hw_start_rx_dma | |
| * TODO: Init ANI here | |
| */ | |
| void ath5k_hw_start_rx_pcu(struct ath5k_hw *ah) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_DIAG_SW, AR5K_DIAG_SW_DIS_RX); | |
| } | |
| /** | |
| * at5k_hw_stop_rx_pcu - Stop RX engine | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * | |
| * Stops RX engine on PCU | |
| * | |
| * TODO: Detach ANI here | |
| */ | |
| void ath5k_hw_stop_rx_pcu(struct ath5k_hw *ah) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW, AR5K_DIAG_SW_DIS_RX); | |
| } | |
| /* | |
| * Set multicast filter | |
| */ | |
| void ath5k_hw_set_mcast_filter(struct ath5k_hw *ah, u32 filter0, u32 filter1) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Set the multicat filter */ | |
| ath5k_hw_reg_write(ah, filter0, AR5K_MCAST_FILTER0); | |
| ath5k_hw_reg_write(ah, filter1, AR5K_MCAST_FILTER1); | |
| } | |
| /* | |
| * Set multicast filter by index | |
| */ | |
| int ath5k_hw_set_mcast_filter_idx(struct ath5k_hw *ah, u32 index) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| if (index >= 64) | |
| return -EINVAL; | |
| else if (index >= 32) | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_MCAST_FILTER1, | |
| (1 << (index - 32))); | |
| else | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_MCAST_FILTER0, (1 << index)); | |
| return 0; | |
| } | |
| /* | |
| * Clear Multicast filter by index | |
| */ | |
| int ath5k_hw_clear_mcast_filter_idx(struct ath5k_hw *ah, u32 index) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| if (index >= 64) | |
| return -EINVAL; | |
| else if (index >= 32) | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_MCAST_FILTER1, | |
| (1 << (index - 32))); | |
| else | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_MCAST_FILTER0, (1 << index)); | |
| return 0; | |
| } | |
| /** | |
| * ath5k_hw_get_rx_filter - Get current rx filter | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * | |
| * Returns the RX filter by reading rx filter and | |
| * phy error filter registers. RX filter is used | |
| * to set the allowed frame types that PCU will accept | |
| * and pass to the driver. For a list of frame types | |
| * check out reg.h. | |
| */ | |
| u32 ath5k_hw_get_rx_filter(struct ath5k_hw *ah) | |
| { | |
| u32 data, filter = 0; | |
| ATH5K_TRACE(ah->ah_sc); | |
| filter = ath5k_hw_reg_read(ah, AR5K_RX_FILTER); | |
| /*Radar detection for 5212*/ | |
| if (ah->ah_version == AR5K_AR5212) { | |
| data = ath5k_hw_reg_read(ah, AR5K_PHY_ERR_FIL); | |
| if (data & AR5K_PHY_ERR_FIL_RADAR) | |
| filter |= AR5K_RX_FILTER_RADARERR; | |
| if (data & (AR5K_PHY_ERR_FIL_OFDM | AR5K_PHY_ERR_FIL_CCK)) | |
| filter |= AR5K_RX_FILTER_PHYERR; | |
| } | |
| return filter; | |
| } | |
| /** | |
| * ath5k_hw_set_rx_filter - Set rx filter | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @filter: RX filter mask (see reg.h) | |
| * | |
| * Sets RX filter register and also handles PHY error filter | |
| * register on 5212 and newer chips so that we have proper PHY | |
| * error reporting. | |
| */ | |
| void ath5k_hw_set_rx_filter(struct ath5k_hw *ah, u32 filter) | |
| { | |
| u32 data = 0; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Set PHY error filter register on 5212*/ | |
| if (ah->ah_version == AR5K_AR5212) { | |
| if (filter & AR5K_RX_FILTER_RADARERR) | |
| data |= AR5K_PHY_ERR_FIL_RADAR; | |
| if (filter & AR5K_RX_FILTER_PHYERR) | |
| data |= AR5K_PHY_ERR_FIL_OFDM | AR5K_PHY_ERR_FIL_CCK; | |
| } | |
| /* | |
| * The AR5210 uses promiscous mode to detect radar activity | |
| */ | |
| if (ah->ah_version == AR5K_AR5210 && | |
| (filter & AR5K_RX_FILTER_RADARERR)) { | |
| filter &= ~AR5K_RX_FILTER_RADARERR; | |
| filter |= AR5K_RX_FILTER_PROM; | |
| } | |
| /*Zero length DMA (phy error reporting) */ | |
| if (data) | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_RXCFG, AR5K_RXCFG_ZLFDMA); | |
| else | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_RXCFG, AR5K_RXCFG_ZLFDMA); | |
| /*Write RX Filter register*/ | |
| ath5k_hw_reg_write(ah, filter & 0xff, AR5K_RX_FILTER); | |
| /*Write PHY error filter register on 5212*/ | |
| if (ah->ah_version == AR5K_AR5212) | |
| ath5k_hw_reg_write(ah, data, AR5K_PHY_ERR_FIL); | |
| } | |
| /****************\ | |
| * Beacon control * | |
| \****************/ | |
| /** | |
| * ath5k_hw_get_tsf32 - Get a 32bit TSF | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * | |
| * Returns lower 32 bits of current TSF | |
| */ | |
| u32 ath5k_hw_get_tsf32(struct ath5k_hw *ah) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| return ath5k_hw_reg_read(ah, AR5K_TSF_L32); | |
| } | |
| /** | |
| * ath5k_hw_get_tsf64 - Get the full 64bit TSF | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * | |
| * Returns the current TSF | |
| */ | |
| u64 ath5k_hw_get_tsf64(struct ath5k_hw *ah) | |
| { | |
| u64 tsf = ath5k_hw_reg_read(ah, AR5K_TSF_U32); | |
| ATH5K_TRACE(ah->ah_sc); | |
| return ath5k_hw_reg_read(ah, AR5K_TSF_L32) | (tsf << 32); | |
| } | |
| /** | |
| * ath5k_hw_set_tsf64 - Set a new 64bit TSF | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * @tsf64: The new 64bit TSF | |
| * | |
| * Sets the new TSF | |
| */ | |
| void ath5k_hw_set_tsf64(struct ath5k_hw *ah, u64 tsf64) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| ath5k_hw_reg_write(ah, tsf64 & 0xffffffff, AR5K_TSF_L32); | |
| ath5k_hw_reg_write(ah, (tsf64 >> 32) & 0xffffffff, AR5K_TSF_U32); | |
| } | |
| /** | |
| * ath5k_hw_reset_tsf - Force a TSF reset | |
| * | |
| * @ah: The &struct ath5k_hw | |
| * | |
| * Forces a TSF reset on PCU | |
| */ | |
| void ath5k_hw_reset_tsf(struct ath5k_hw *ah) | |
| { | |
| u32 val; | |
| ATH5K_TRACE(ah->ah_sc); | |
| val = ath5k_hw_reg_read(ah, AR5K_BEACON) | AR5K_BEACON_RESET_TSF; | |
| /* | |
| * Each write to the RESET_TSF bit toggles a hardware internal | |
| * signal to reset TSF, but if left high it will cause a TSF reset | |
| * on the next chip reset as well. Thus we always write the value | |
| * twice to clear the signal. | |
| */ | |
| ath5k_hw_reg_write(ah, val, AR5K_BEACON); | |
| ath5k_hw_reg_write(ah, val, AR5K_BEACON); | |
| } | |
| /* | |
| * Initialize beacon timers | |
| */ | |
| void ath5k_hw_init_beacon(struct ath5k_hw *ah, u32 next_beacon, u32 interval) | |
| { | |
| u32 timer1, timer2, timer3; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* | |
| * Set the additional timers by mode | |
| */ | |
| switch (ah->ah_op_mode) { | |
| case NL80211_IFTYPE_MONITOR: | |
| case NL80211_IFTYPE_STATION: | |
| /* In STA mode timer1 is used as next wakeup | |
| * timer and timer2 as next CFP duration start | |
| * timer. Both in 1/8TUs. */ | |
| /* TODO: PCF handling */ | |
| if (ah->ah_version == AR5K_AR5210) { | |
| timer1 = 0xffffffff; | |
| timer2 = 0xffffffff; | |
| } else { | |
| timer1 = 0x0000ffff; | |
| timer2 = 0x0007ffff; | |
| } | |
| /* Mark associated AP as PCF incapable for now */ | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_STA_ID1, AR5K_STA_ID1_PCF); | |
| break; | |
| case NL80211_IFTYPE_ADHOC: | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_TXCFG, AR5K_TXCFG_ADHOC_BCN_ATIM); | |
| default: | |
| /* On non-STA modes timer1 is used as next DMA | |
| * beacon alert (DBA) timer and timer2 as next | |
| * software beacon alert. Both in 1/8TUs. */ | |
| timer1 = (next_beacon - AR5K_TUNE_DMA_BEACON_RESP) << 3; | |
| timer2 = (next_beacon - AR5K_TUNE_SW_BEACON_RESP) << 3; | |
| break; | |
| } | |
| /* Timer3 marks the end of our ATIM window | |
| * a zero length window is not allowed because | |
| * we 'll get no beacons */ | |
| timer3 = next_beacon + (ah->ah_atim_window ? ah->ah_atim_window : 1); | |
| /* | |
| * Set the beacon register and enable all timers. | |
| */ | |
| /* When in AP mode zero timer0 to start TSF */ | |
| if (ah->ah_op_mode == NL80211_IFTYPE_AP) | |
| ath5k_hw_reg_write(ah, 0, AR5K_TIMER0); | |
| else | |
| ath5k_hw_reg_write(ah, next_beacon, AR5K_TIMER0); | |
| ath5k_hw_reg_write(ah, timer1, AR5K_TIMER1); | |
| ath5k_hw_reg_write(ah, timer2, AR5K_TIMER2); | |
| ath5k_hw_reg_write(ah, timer3, AR5K_TIMER3); | |
| /* Force a TSF reset if requested and enable beacons */ | |
| if (interval & AR5K_BEACON_RESET_TSF) | |
| ath5k_hw_reset_tsf(ah); | |
| ath5k_hw_reg_write(ah, interval & (AR5K_BEACON_PERIOD | | |
| AR5K_BEACON_ENABLE), | |
| AR5K_BEACON); | |
| /* Flush any pending BMISS interrupts on ISR by | |
| * performing a clear-on-write operation on PISR | |
| * register for the BMISS bit (writing a bit on | |
| * ISR togles a reset for that bit and leaves | |
| * the rest bits intact) */ | |
| if (ah->ah_version == AR5K_AR5210) | |
| ath5k_hw_reg_write(ah, AR5K_ISR_BMISS, AR5K_ISR); | |
| else | |
| ath5k_hw_reg_write(ah, AR5K_ISR_BMISS, AR5K_PISR); | |
| /* TODO: Set enchanced sleep registers on AR5212 | |
| * based on vif->bss_conf params, until then | |
| * disable power save reporting.*/ | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_STA_ID1, AR5K_STA_ID1_PWR_SV); | |
| } | |
| #if 0 | |
| /* | |
| * Set beacon timers | |
| */ | |
| int ath5k_hw_set_beacon_timers(struct ath5k_hw *ah, | |
| const struct ath5k_beacon_state *state) | |
| { | |
| u32 cfp_period, next_cfp, dtim, interval, next_beacon; | |
| /* | |
| * TODO: should be changed through *state | |
| * review struct ath5k_beacon_state struct | |
| * | |
| * XXX: These are used for cfp period bellow, are they | |
| * ok ? Is it O.K. for tsf here to be 0 or should we use | |
| * get_tsf ? | |
| */ | |
| u32 dtim_count = 0; /* XXX */ | |
| u32 cfp_count = 0; /* XXX */ | |
| u32 tsf = 0; /* XXX */ | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Return on an invalid beacon state */ | |
| if (state->bs_interval < 1) | |
| return -EINVAL; | |
| interval = state->bs_interval; | |
| dtim = state->bs_dtim_period; | |
| /* | |
| * PCF support? | |
| */ | |
| if (state->bs_cfp_period > 0) { | |
| /* | |
| * Enable PCF mode and set the CFP | |
| * (Contention Free Period) and timer registers | |
| */ | |
| cfp_period = state->bs_cfp_period * state->bs_dtim_period * | |
| state->bs_interval; | |
| next_cfp = (cfp_count * state->bs_dtim_period + dtim_count) * | |
| state->bs_interval; | |
| AR5K_REG_ENABLE_BITS(ah, AR5K_STA_ID1, | |
| AR5K_STA_ID1_DEFAULT_ANTENNA | | |
| AR5K_STA_ID1_PCF); | |
| ath5k_hw_reg_write(ah, cfp_period, AR5K_CFP_PERIOD); | |
| ath5k_hw_reg_write(ah, state->bs_cfp_max_duration, | |
| AR5K_CFP_DUR); | |
| ath5k_hw_reg_write(ah, (tsf + (next_cfp == 0 ? cfp_period : | |
| next_cfp)) << 3, AR5K_TIMER2); | |
| } else { | |
| /* Disable PCF mode */ | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_STA_ID1, | |
| AR5K_STA_ID1_DEFAULT_ANTENNA | | |
| AR5K_STA_ID1_PCF); | |
| } | |
| /* | |
| * Enable the beacon timer register | |
| */ | |
| ath5k_hw_reg_write(ah, state->bs_next_beacon, AR5K_TIMER0); | |
| /* | |
| * Start the beacon timers | |
| */ | |
| ath5k_hw_reg_write(ah, (ath5k_hw_reg_read(ah, AR5K_BEACON) & | |
| ~(AR5K_BEACON_PERIOD | AR5K_BEACON_TIM)) | | |
| AR5K_REG_SM(state->bs_tim_offset ? state->bs_tim_offset + 4 : 0, | |
| AR5K_BEACON_TIM) | AR5K_REG_SM(state->bs_interval, | |
| AR5K_BEACON_PERIOD), AR5K_BEACON); | |
| /* | |
| * Write new beacon miss threshold, if it appears to be valid | |
| * XXX: Figure out right values for min <= bs_bmiss_threshold <= max | |
| * and return if its not in range. We can test this by reading value and | |
| * setting value to a largest value and seeing which values register. | |
| */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_RSSI_THR, AR5K_RSSI_THR_BMISS, | |
| state->bs_bmiss_threshold); | |
| /* | |
| * Set sleep control register | |
| * XXX: Didn't find this in 5210 code but since this register | |
| * exists also in ar5k's 5210 headers i leave it as common code. | |
| */ | |
| AR5K_REG_WRITE_BITS(ah, AR5K_SLEEP_CTL, AR5K_SLEEP_CTL_SLDUR, | |
| (state->bs_sleep_duration - 3) << 3); | |
| /* | |
| * Set enhanced sleep registers on 5212 | |
| */ | |
| if (ah->ah_version == AR5K_AR5212) { | |
| if (state->bs_sleep_duration > state->bs_interval && | |
| roundup(state->bs_sleep_duration, interval) == | |
| state->bs_sleep_duration) | |
| interval = state->bs_sleep_duration; | |
| if (state->bs_sleep_duration > dtim && (dtim == 0 || | |
| roundup(state->bs_sleep_duration, dtim) == | |
| state->bs_sleep_duration)) | |
| dtim = state->bs_sleep_duration; | |
| if (interval > dtim) | |
| return -EINVAL; | |
| next_beacon = interval == dtim ? state->bs_next_dtim : | |
| state->bs_next_beacon; | |
| ath5k_hw_reg_write(ah, | |
| AR5K_REG_SM((state->bs_next_dtim - 3) << 3, | |
| AR5K_SLEEP0_NEXT_DTIM) | | |
| AR5K_REG_SM(10, AR5K_SLEEP0_CABTO) | | |
| AR5K_SLEEP0_ENH_SLEEP_EN | | |
| AR5K_SLEEP0_ASSUME_DTIM, AR5K_SLEEP0); | |
| ath5k_hw_reg_write(ah, AR5K_REG_SM((next_beacon - 3) << 3, | |
| AR5K_SLEEP1_NEXT_TIM) | | |
| AR5K_REG_SM(10, AR5K_SLEEP1_BEACON_TO), AR5K_SLEEP1); | |
| ath5k_hw_reg_write(ah, | |
| AR5K_REG_SM(interval, AR5K_SLEEP2_TIM_PER) | | |
| AR5K_REG_SM(dtim, AR5K_SLEEP2_DTIM_PER), AR5K_SLEEP2); | |
| } | |
| return 0; | |
| } | |
| /* | |
| * Reset beacon timers | |
| */ | |
| void ath5k_hw_reset_beacon(struct ath5k_hw *ah) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* | |
| * Disable beacon timer | |
| */ | |
| ath5k_hw_reg_write(ah, 0, AR5K_TIMER0); | |
| /* | |
| * Disable some beacon register values | |
| */ | |
| AR5K_REG_DISABLE_BITS(ah, AR5K_STA_ID1, | |
| AR5K_STA_ID1_DEFAULT_ANTENNA | AR5K_STA_ID1_PCF); | |
| ath5k_hw_reg_write(ah, AR5K_BEACON_PERIOD, AR5K_BEACON); | |
| } | |
| /* | |
| * Wait for beacon queue to finish | |
| */ | |
| int ath5k_hw_beaconq_finish(struct ath5k_hw *ah, unsigned long phys_addr) | |
| { | |
| unsigned int i; | |
| int ret; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* 5210 doesn't have QCU*/ | |
| if (ah->ah_version == AR5K_AR5210) { | |
| /* | |
| * Wait for beaconn queue to finish by checking | |
| * Control Register and Beacon Status Register. | |
| */ | |
| for (i = AR5K_TUNE_BEACON_INTERVAL / 2; i > 0; i--) { | |
| if (!(ath5k_hw_reg_read(ah, AR5K_BSR) & AR5K_BSR_TXQ1F) | |
| || | |
| !(ath5k_hw_reg_read(ah, AR5K_CR) & AR5K_BSR_TXQ1F)) | |
| break; | |
| udelay(10); | |
| } | |
| /* Timeout... */ | |
| if (i <= 0) { | |
| /* | |
| * Re-schedule the beacon queue | |
| */ | |
| ath5k_hw_reg_write(ah, phys_addr, AR5K_NOQCU_TXDP1); | |
| ath5k_hw_reg_write(ah, AR5K_BCR_TQ1V | AR5K_BCR_BDMAE, | |
| AR5K_BCR); | |
| return -EIO; | |
| } | |
| ret = 0; | |
| } else { | |
| /*5211/5212*/ | |
| ret = ath5k_hw_register_timeout(ah, | |
| AR5K_QUEUE_STATUS(AR5K_TX_QUEUE_ID_BEACON), | |
| AR5K_QCU_STS_FRMPENDCNT, 0, false); | |
| if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXE, AR5K_TX_QUEUE_ID_BEACON)) | |
| return -EIO; | |
| } | |
| return ret; | |
| } | |
| #endif | |
| /*********************\ | |
| * Key table functions * | |
| \*********************/ | |
| /* | |
| * Reset a key entry on the table | |
| */ | |
| int ath5k_hw_reset_key(struct ath5k_hw *ah, u16 entry) | |
| { | |
| unsigned int i, type; | |
| u16 micentry = entry + AR5K_KEYTABLE_MIC_OFFSET; | |
| ATH5K_TRACE(ah->ah_sc); | |
| AR5K_ASSERT_ENTRY(entry, AR5K_KEYTABLE_SIZE); | |
| type = ath5k_hw_reg_read(ah, AR5K_KEYTABLE_TYPE(entry)); | |
| for (i = 0; i < AR5K_KEYCACHE_SIZE; i++) | |
| ath5k_hw_reg_write(ah, 0, AR5K_KEYTABLE_OFF(entry, i)); | |
| /* Reset associated MIC entry if TKIP | |
| * is enabled located at offset (entry + 64) */ | |
| if (type == AR5K_KEYTABLE_TYPE_TKIP) { | |
| AR5K_ASSERT_ENTRY(micentry, AR5K_KEYTABLE_SIZE); | |
| for (i = 0; i < AR5K_KEYCACHE_SIZE / 2 ; i++) | |
| ath5k_hw_reg_write(ah, 0, | |
| AR5K_KEYTABLE_OFF(micentry, i)); | |
| } | |
| /* | |
| * Set NULL encryption on AR5212+ | |
| * | |
| * Note: AR5K_KEYTABLE_TYPE -> AR5K_KEYTABLE_OFF(entry, 5) | |
| * AR5K_KEYTABLE_TYPE_NULL -> 0x00000007 | |
| * | |
| * Note2: Windows driver (ndiswrapper) sets this to | |
| * 0x00000714 instead of 0x00000007 | |
| */ | |
| if (ah->ah_version > AR5K_AR5211) { | |
| ath5k_hw_reg_write(ah, AR5K_KEYTABLE_TYPE_NULL, | |
| AR5K_KEYTABLE_TYPE(entry)); | |
| if (type == AR5K_KEYTABLE_TYPE_TKIP) { | |
| ath5k_hw_reg_write(ah, AR5K_KEYTABLE_TYPE_NULL, | |
| AR5K_KEYTABLE_TYPE(micentry)); | |
| } | |
| } | |
| return 0; | |
| } | |
| /* | |
| * Check if a table entry is valid | |
| */ | |
| int ath5k_hw_is_key_valid(struct ath5k_hw *ah, u16 entry) | |
| { | |
| ATH5K_TRACE(ah->ah_sc); | |
| AR5K_ASSERT_ENTRY(entry, AR5K_KEYTABLE_SIZE); | |
| /* Check the validation flag at the end of the entry */ | |
| return ath5k_hw_reg_read(ah, AR5K_KEYTABLE_MAC1(entry)) & | |
| AR5K_KEYTABLE_VALID; | |
| } | |
| static | |
| int ath5k_keycache_type(const struct ieee80211_key_conf *key) | |
| { | |
| switch (key->alg) { | |
| case ALG_TKIP: | |
| return AR5K_KEYTABLE_TYPE_TKIP; | |
| case ALG_CCMP: | |
| return AR5K_KEYTABLE_TYPE_CCM; | |
| case ALG_WEP: | |
| if (key->keylen == LEN_WEP40) | |
| return AR5K_KEYTABLE_TYPE_40; | |
| else if (key->keylen == LEN_WEP104) | |
| return AR5K_KEYTABLE_TYPE_104; | |
| return -EINVAL; | |
| default: | |
| return -EINVAL; | |
| } | |
| return -EINVAL; | |
| } | |
| /* | |
| * Set a key entry on the table | |
| */ | |
| int ath5k_hw_set_key(struct ath5k_hw *ah, u16 entry, | |
| const struct ieee80211_key_conf *key, const u8 *mac) | |
| { | |
| unsigned int i; | |
| int keylen; | |
| __le32 key_v[5] = {}; | |
| __le32 key0 = 0, key1 = 0; | |
| __le32 *rxmic, *txmic; | |
| int keytype; | |
| u16 micentry = entry + AR5K_KEYTABLE_MIC_OFFSET; | |
| bool is_tkip; | |
| const u8 *key_ptr; | |
| ATH5K_TRACE(ah->ah_sc); | |
| is_tkip = (key->alg == ALG_TKIP); | |
| /* | |
| * key->keylen comes in from mac80211 in bytes. | |
| * TKIP is 128 bit + 128 bit mic | |
| */ | |
| keylen = (is_tkip) ? (128 / 8) : key->keylen; | |
| if (entry > AR5K_KEYTABLE_SIZE || | |
| (is_tkip && micentry > AR5K_KEYTABLE_SIZE)) | |
| return -EOPNOTSUPP; | |
| if (unlikely(keylen > 16)) | |
| return -EOPNOTSUPP; | |
| keytype = ath5k_keycache_type(key); | |
| if (keytype < 0) | |
| return keytype; | |
| /* | |
| * each key block is 6 bytes wide, written as pairs of | |
| * alternating 32 and 16 bit le values. | |
| */ | |
| key_ptr = key->key; | |
| for (i = 0; keylen >= 6; keylen -= 6) { | |
| memcpy(&key_v[i], key_ptr, 6); | |
| i += 2; | |
| key_ptr += 6; | |
| } | |
| if (keylen) | |
| memcpy(&key_v[i], key_ptr, keylen); | |
| /* intentionally corrupt key until mic is installed */ | |
| if (is_tkip) { | |
| key0 = key_v[0] = ~key_v[0]; | |
| key1 = key_v[1] = ~key_v[1]; | |
| } | |
| for (i = 0; i < ARRAY_SIZE(key_v); i++) | |
| ath5k_hw_reg_write(ah, le32_to_cpu(key_v[i]), | |
| AR5K_KEYTABLE_OFF(entry, i)); | |
| ath5k_hw_reg_write(ah, keytype, AR5K_KEYTABLE_TYPE(entry)); | |
| if (is_tkip) { | |
| /* Install rx/tx MIC */ | |
| rxmic = (__le32 *) &key->key[16]; | |
| txmic = (__le32 *) &key->key[24]; | |
| if (ah->ah_combined_mic) { | |
| key_v[0] = rxmic[0]; | |
| key_v[1] = cpu_to_le32(le32_to_cpu(txmic[0]) >> 16); | |
| key_v[2] = rxmic[1]; | |
| key_v[3] = cpu_to_le32(le32_to_cpu(txmic[0]) & 0xffff); | |
| key_v[4] = txmic[1]; | |
| } else { | |
| key_v[0] = rxmic[0]; | |
| key_v[1] = 0; | |
| key_v[2] = rxmic[1]; | |
| key_v[3] = 0; | |
| key_v[4] = 0; | |
| } | |
| for (i = 0; i < ARRAY_SIZE(key_v); i++) | |
| ath5k_hw_reg_write(ah, le32_to_cpu(key_v[i]), | |
| AR5K_KEYTABLE_OFF(micentry, i)); | |
| ath5k_hw_reg_write(ah, AR5K_KEYTABLE_TYPE_NULL, | |
| AR5K_KEYTABLE_TYPE(micentry)); | |
| ath5k_hw_reg_write(ah, 0, AR5K_KEYTABLE_MAC0(micentry)); | |
| ath5k_hw_reg_write(ah, 0, AR5K_KEYTABLE_MAC1(micentry)); | |
| /* restore first 2 words of key */ | |
| ath5k_hw_reg_write(ah, le32_to_cpu(~key0), | |
| AR5K_KEYTABLE_OFF(entry, 0)); | |
| ath5k_hw_reg_write(ah, le32_to_cpu(~key1), | |
| AR5K_KEYTABLE_OFF(entry, 1)); | |
| } | |
| return ath5k_hw_set_key_lladdr(ah, entry, mac); | |
| } | |
| int ath5k_hw_set_key_lladdr(struct ath5k_hw *ah, u16 entry, const u8 *mac) | |
| { | |
| u32 low_id, high_id; | |
| ATH5K_TRACE(ah->ah_sc); | |
| /* Invalid entry (key table overflow) */ | |
| AR5K_ASSERT_ENTRY(entry, AR5K_KEYTABLE_SIZE); | |
| /* MAC may be NULL if it's a broadcast key. In this case no need to | |
| * to compute AR5K_LOW_ID and AR5K_HIGH_ID as we already know it. */ | |
| if (!mac) { | |
| low_id = 0xffffffff; | |
| high_id = 0xffff | AR5K_KEYTABLE_VALID; | |
| } else { | |
| low_id = AR5K_LOW_ID(mac); | |
| high_id = AR5K_HIGH_ID(mac) | AR5K_KEYTABLE_VALID; | |
| } | |
| ath5k_hw_reg_write(ah, low_id, AR5K_KEYTABLE_MAC0(entry)); | |
| ath5k_hw_reg_write(ah, high_id, AR5K_KEYTABLE_MAC1(entry)); | |
| return 0; | |
| } | |