arch/arm/mach-ep93xx/timer-ep93xx.c

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <asm/mach/time.h>
#include "soc.h"

/*************************************************************************
 * Timer handling for EP93xx
 *************************************************************************
 * The ep93xx has four internal timers.  Timers 1, 2 (both 16 bit) and
 * 3 (32 bit) count down at 508 kHz, are self-reloading, and can generate
 * an interrupt on underflow.  Timer 4 (40 bit) counts down at 983.04 kHz,
 * is free-running, and can't generate interrupts.
 *
 * The 508 kHz timers are ideal for use for the timer interrupt, as the
 * most common values of HZ divide 508 kHz nicely.  We pick one of the 16
 * bit timers (timer 1) since we don't need more than 16 bits of reload
 * value as long as HZ >= 8.
 *
 * The higher clock rate of timer 4 makes it a better choice than the
 * other timers for use in gettimeoffset(), while the fact that it can't
 * generate interrupts means we don't have to worry about not being able
 * to use this timer for something else.  We also use timer 4 for keeping
 * track of lost jiffies.
 */
#define EP93XX_TIMER_REG(x)		(EP93XX_TIMER_BASE + (x))
#define EP93XX_TIMER1_LOAD		EP93XX_TIMER_REG(0x00)
#define EP93XX_TIMER1_VALUE		EP93XX_TIMER_REG(0x04)
#define EP93XX_TIMER1_CONTROL		EP93XX_TIMER_REG(0x08)
#define EP93XX_TIMER123_CONTROL_ENABLE	(1 << 7)
#define EP93XX_TIMER123_CONTROL_MODE	(1 << 6)
#define EP93XX_TIMER123_CONTROL_CLKSEL	(1 << 3)
#define EP93XX_TIMER1_CLEAR		EP93XX_TIMER_REG(0x0c)
#define EP93XX_TIMER2_LOAD		EP93XX_TIMER_REG(0x20)
#define EP93XX_TIMER2_VALUE		EP93XX_TIMER_REG(0x24)
#define EP93XX_TIMER2_CONTROL		EP93XX_TIMER_REG(0x28)
#define EP93XX_TIMER2_CLEAR		EP93XX_TIMER_REG(0x2c)
#define EP93XX_TIMER4_VALUE_LOW		EP93XX_TIMER_REG(0x60)
#define EP93XX_TIMER4_VALUE_HIGH	EP93XX_TIMER_REG(0x64)
#define EP93XX_TIMER4_VALUE_HIGH_ENABLE	(1 << 8)
#define EP93XX_TIMER3_LOAD		EP93XX_TIMER_REG(0x80)
#define EP93XX_TIMER3_VALUE		EP93XX_TIMER_REG(0x84)
#define EP93XX_TIMER3_CONTROL		EP93XX_TIMER_REG(0x88)
#define EP93XX_TIMER3_CLEAR		EP93XX_TIMER_REG(0x8c)

#define EP93XX_TIMER123_CLOCK		508469
#define EP93XX_TIMER4_CLOCK		983040

#define TIMER1_RELOAD			((EP93XX_TIMER123_CLOCK / HZ) - 1)
#define TIMER4_TICKS_PER_JIFFY		DIV_ROUND_CLOSEST(EP93XX_TIMER4_CLOCK, HZ)

static unsigned int last_jiffy_time;

static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
{
	/* Writing any value clears the timer interrupt */
	__raw_writel(1, EP93XX_TIMER1_CLEAR);

	/* Recover lost jiffies */
	while ((signed long)
		(__raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time)
						>= TIMER4_TICKS_PER_JIFFY) {
		last_jiffy_time += TIMER4_TICKS_PER_JIFFY;
		timer_tick();
	}

	return IRQ_HANDLED;
}

static struct irqaction ep93xx_timer_irq = {
	.name		= "ep93xx timer",
	.flags		= IRQF_TIMER | IRQF_IRQPOLL,
	.handler	= ep93xx_timer_interrupt,
};

static u32 ep93xx_gettimeoffset(void)
{
	int offset;

	offset = __raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time;

	/*
	 * Timer 4 is based on a 983.04 kHz reference clock,
	 * so dividing by 983040 gives the fraction of a second,
	 * so dividing by 0.983040 converts to uS.
	 * Refactor the calculation to avoid overflow.
	 * Finally, multiply by 1000 to give nS.
	 */
	return (offset + (53 * offset / 3072)) * 1000;
}

void __init ep93xx_timer_init(void)
{
	u32 tmode = EP93XX_TIMER123_CONTROL_MODE |
		    EP93XX_TIMER123_CONTROL_CLKSEL;

	arch_gettimeoffset = ep93xx_gettimeoffset;

	/* Enable periodic HZ timer.  */
	__raw_writel(tmode, EP93XX_TIMER1_CONTROL);
	__raw_writel(TIMER1_RELOAD, EP93XX_TIMER1_LOAD);
	__raw_writel(tmode | EP93XX_TIMER123_CONTROL_ENABLE,
			EP93XX_TIMER1_CONTROL);

	/* Enable lost jiffy timer.  */
	__raw_writel(EP93XX_TIMER4_VALUE_HIGH_ENABLE,
			EP93XX_TIMER4_VALUE_HIGH);

	setup_irq(IRQ_EP93XX_TIMER1, &ep93xx_timer_irq);
}