| /* intel_pch_thermal.c - Intel PCH Thermal driver | 
 |  * | 
 |  * Copyright (c) 2015, Intel Corporation. | 
 |  * | 
 |  * Authors: | 
 |  *     Tushar Dave <tushar.n.dave@intel.com> | 
 |  * | 
 |  * This program is free software; you can redistribute it and/or modify it | 
 |  * under the terms and conditions of the GNU General Public License, | 
 |  * version 2, as published by the Free Software Foundation. | 
 |  * | 
 |  * This program is distributed in the hope it will be useful, but WITHOUT | 
 |  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or | 
 |  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for | 
 |  * more details. | 
 |  * | 
 |  */ | 
 |  | 
 | #include <linux/module.h> | 
 | #include <linux/types.h> | 
 | #include <linux/init.h> | 
 | #include <linux/pci.h> | 
 | #include <linux/thermal.h> | 
 |  | 
 | /* Intel PCH thermal Device IDs */ | 
 | #define PCH_THERMAL_DID_WPT	0x9CA4 /* Wildcat Point */ | 
 |  | 
 | /* Wildcat Point-LP  PCH Thermal registers */ | 
 | #define WPT_TEMP	0x0000	/* Temperature */ | 
 | #define WPT_TSC	0x04	/* Thermal Sensor Control */ | 
 | #define WPT_TSS	0x06	/* Thermal Sensor Status */ | 
 | #define WPT_TSEL	0x08	/* Thermal Sensor Enable and Lock */ | 
 | #define WPT_TSREL	0x0A	/* Thermal Sensor Report Enable and Lock */ | 
 | #define WPT_TSMIC	0x0C	/* Thermal Sensor SMI Control */ | 
 | #define WPT_CTT	0x0010	/* Catastrophic Trip Point */ | 
 | #define WPT_TAHV	0x0014	/* Thermal Alert High Value */ | 
 | #define WPT_TALV	0x0018	/* Thermal Alert Low Value */ | 
 | #define WPT_TL		0x00000040	/* Throttle Value */ | 
 | #define WPT_PHL	0x0060	/* PCH Hot Level */ | 
 | #define WPT_PHLC	0x62	/* PHL Control */ | 
 | #define WPT_TAS	0x80	/* Thermal Alert Status */ | 
 | #define WPT_TSPIEN	0x82	/* PCI Interrupt Event Enables */ | 
 | #define WPT_TSGPEN	0x84	/* General Purpose Event Enables */ | 
 |  | 
 | /*  Wildcat Point-LP  PCH Thermal Register bit definitions */ | 
 | #define WPT_TEMP_TSR	0x00ff	/* Temp TS Reading */ | 
 | #define WPT_TSC_CPDE	0x01	/* Catastrophic Power-Down Enable */ | 
 | #define WPT_TSS_TSDSS	0x10	/* Thermal Sensor Dynamic Shutdown Status */ | 
 | #define WPT_TSS_GPES	0x08	/* GPE status */ | 
 | #define WPT_TSEL_ETS	0x01    /* Enable TS */ | 
 | #define WPT_TSEL_PLDB	0x80	/* TSEL Policy Lock-Down Bit */ | 
 | #define WPT_TL_TOL	0x000001FF	/* T0 Level */ | 
 | #define WPT_TL_T1L	0x1ff00000	/* T1 Level */ | 
 | #define WPT_TL_TTEN	0x20000000	/* TT Enable */ | 
 |  | 
 | static char driver_name[] = "Intel PCH thermal driver"; | 
 |  | 
 | struct pch_thermal_device { | 
 | 	void __iomem *hw_base; | 
 | 	const struct pch_dev_ops *ops; | 
 | 	struct pci_dev *pdev; | 
 | 	struct thermal_zone_device *tzd; | 
 | 	int crt_trip_id; | 
 | 	unsigned long crt_temp; | 
 | 	int hot_trip_id; | 
 | 	unsigned long hot_temp; | 
 | }; | 
 |  | 
 | static int pch_wpt_init(struct pch_thermal_device *ptd, int *nr_trips) | 
 | { | 
 | 	u8 tsel; | 
 | 	u16 trip_temp; | 
 |  | 
 | 	*nr_trips = 0; | 
 |  | 
 | 	/* Check if BIOS has already enabled thermal sensor */ | 
 | 	if (WPT_TSS_TSDSS & readb(ptd->hw_base + WPT_TSS)) | 
 | 		goto read_trips; | 
 |  | 
 | 	tsel = readb(ptd->hw_base + WPT_TSEL); | 
 | 	/* | 
 | 	 * When TSEL's Policy Lock-Down bit is 1, TSEL become RO. | 
 | 	 * If so, thermal sensor cannot enable. Bail out. | 
 | 	 */ | 
 | 	if (tsel & WPT_TSEL_PLDB) { | 
 | 		dev_err(&ptd->pdev->dev, "Sensor can't be enabled\n"); | 
 | 		return -ENODEV; | 
 | 	} | 
 |  | 
 | 	writeb(tsel|WPT_TSEL_ETS, ptd->hw_base + WPT_TSEL); | 
 | 	if (!(WPT_TSS_TSDSS & readb(ptd->hw_base + WPT_TSS))) { | 
 | 		dev_err(&ptd->pdev->dev, "Sensor can't be enabled\n"); | 
 | 		return -ENODEV; | 
 | 	} | 
 |  | 
 | read_trips: | 
 | 	ptd->crt_trip_id = -1; | 
 | 	trip_temp = readw(ptd->hw_base + WPT_CTT); | 
 | 	trip_temp &= 0x1FF; | 
 | 	if (trip_temp) { | 
 | 		/* Resolution of 1/2 degree C and an offset of -50C */ | 
 | 		ptd->crt_temp = trip_temp * 1000 / 2 - 50000; | 
 | 		ptd->crt_trip_id = 0; | 
 | 		++(*nr_trips); | 
 | 	} | 
 |  | 
 | 	ptd->hot_trip_id = -1; | 
 | 	trip_temp = readw(ptd->hw_base + WPT_PHL); | 
 | 	trip_temp &= 0x1FF; | 
 | 	if (trip_temp) { | 
 | 		/* Resolution of 1/2 degree C and an offset of -50C */ | 
 | 		ptd->hot_temp = trip_temp * 1000 / 2 - 50000; | 
 | 		ptd->hot_trip_id = *nr_trips; | 
 | 		++(*nr_trips); | 
 | 	} | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int pch_wpt_get_temp(struct pch_thermal_device *ptd, int *temp) | 
 | { | 
 | 	u8 wpt_temp; | 
 |  | 
 | 	wpt_temp = WPT_TEMP_TSR & readl(ptd->hw_base + WPT_TEMP); | 
 |  | 
 | 	/* Resolution of 1/2 degree C and an offset of -50C */ | 
 | 	*temp = (wpt_temp * 1000 / 2 - 50000); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | struct pch_dev_ops { | 
 | 	int (*hw_init)(struct pch_thermal_device *ptd, int *nr_trips); | 
 | 	int (*get_temp)(struct pch_thermal_device *ptd, int *temp); | 
 | }; | 
 |  | 
 |  | 
 | /* dev ops for Wildcat Point */ | 
 | static struct pch_dev_ops pch_dev_ops_wpt = { | 
 | 	.hw_init = pch_wpt_init, | 
 | 	.get_temp = pch_wpt_get_temp, | 
 | }; | 
 |  | 
 | static int pch_thermal_get_temp(struct thermal_zone_device *tzd, int *temp) | 
 | { | 
 | 	struct pch_thermal_device *ptd = tzd->devdata; | 
 |  | 
 | 	return	ptd->ops->get_temp(ptd, temp); | 
 | } | 
 |  | 
 | static int pch_get_trip_type(struct thermal_zone_device *tzd, int trip, | 
 | 			     enum thermal_trip_type *type) | 
 | { | 
 | 	struct pch_thermal_device *ptd = tzd->devdata; | 
 |  | 
 | 	if (ptd->crt_trip_id == trip) | 
 | 		*type = THERMAL_TRIP_CRITICAL; | 
 | 	else if (ptd->hot_trip_id == trip) | 
 | 		*type = THERMAL_TRIP_HOT; | 
 | 	else | 
 | 		return -EINVAL; | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int pch_get_trip_temp(struct thermal_zone_device *tzd, int trip, int *temp) | 
 | { | 
 | 	struct pch_thermal_device *ptd = tzd->devdata; | 
 |  | 
 | 	if (ptd->crt_trip_id == trip) | 
 | 		*temp = ptd->crt_temp; | 
 | 	else if (ptd->hot_trip_id == trip) | 
 | 		*temp = ptd->hot_temp; | 
 | 	else | 
 | 		return -EINVAL; | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static struct thermal_zone_device_ops tzd_ops = { | 
 | 	.get_temp = pch_thermal_get_temp, | 
 | 	.get_trip_type = pch_get_trip_type, | 
 | 	.get_trip_temp = pch_get_trip_temp, | 
 | }; | 
 |  | 
 |  | 
 | static int intel_pch_thermal_probe(struct pci_dev *pdev, | 
 | 				   const struct pci_device_id *id) | 
 | { | 
 | 	struct pch_thermal_device *ptd; | 
 | 	int err; | 
 | 	int nr_trips; | 
 | 	char *dev_name; | 
 |  | 
 | 	ptd = devm_kzalloc(&pdev->dev, sizeof(*ptd), GFP_KERNEL); | 
 | 	if (!ptd) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	switch (pdev->device) { | 
 | 	case PCH_THERMAL_DID_WPT: | 
 | 		ptd->ops = &pch_dev_ops_wpt; | 
 | 		dev_name = "pch_wildcat_point"; | 
 | 		break; | 
 | 	default: | 
 | 		dev_err(&pdev->dev, "unknown pch thermal device\n"); | 
 | 		return -ENODEV; | 
 | 	} | 
 |  | 
 | 	pci_set_drvdata(pdev, ptd); | 
 | 	ptd->pdev = pdev; | 
 |  | 
 | 	err = pci_enable_device(pdev); | 
 | 	if (err) { | 
 | 		dev_err(&pdev->dev, "failed to enable pci device\n"); | 
 | 		return err; | 
 | 	} | 
 |  | 
 | 	err = pci_request_regions(pdev, driver_name); | 
 | 	if (err) { | 
 | 		dev_err(&pdev->dev, "failed to request pci region\n"); | 
 | 		goto error_disable; | 
 | 	} | 
 |  | 
 | 	ptd->hw_base = pci_ioremap_bar(pdev, 0); | 
 | 	if (!ptd->hw_base) { | 
 | 		err = -ENOMEM; | 
 | 		dev_err(&pdev->dev, "failed to map mem base\n"); | 
 | 		goto error_release; | 
 | 	} | 
 |  | 
 | 	err = ptd->ops->hw_init(ptd, &nr_trips); | 
 | 	if (err) | 
 | 		goto error_cleanup; | 
 |  | 
 | 	ptd->tzd = thermal_zone_device_register(dev_name, nr_trips, 0, ptd, | 
 | 						&tzd_ops, NULL, 0, 0); | 
 | 	if (IS_ERR(ptd->tzd)) { | 
 | 		dev_err(&pdev->dev, "Failed to register thermal zone %s\n", | 
 | 			dev_name); | 
 | 		err = PTR_ERR(ptd->tzd); | 
 | 		goto error_cleanup; | 
 | 	} | 
 |  | 
 | 	return 0; | 
 |  | 
 | error_cleanup: | 
 | 	iounmap(ptd->hw_base); | 
 | error_release: | 
 | 	pci_release_regions(pdev); | 
 | error_disable: | 
 | 	pci_disable_device(pdev); | 
 | 	dev_err(&pdev->dev, "pci device failed to probe\n"); | 
 | 	return err; | 
 | } | 
 |  | 
 | static void intel_pch_thermal_remove(struct pci_dev *pdev) | 
 | { | 
 | 	struct pch_thermal_device *ptd = pci_get_drvdata(pdev); | 
 |  | 
 | 	thermal_zone_device_unregister(ptd->tzd); | 
 | 	iounmap(ptd->hw_base); | 
 | 	pci_set_drvdata(pdev, NULL); | 
 | 	pci_release_region(pdev, 0); | 
 | 	pci_disable_device(pdev); | 
 | } | 
 |  | 
 | static struct pci_device_id intel_pch_thermal_id[] = { | 
 | 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WPT) }, | 
 | 	{ 0, }, | 
 | }; | 
 | MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id); | 
 |  | 
 | static struct pci_driver intel_pch_thermal_driver = { | 
 | 	.name		= "intel_pch_thermal", | 
 | 	.id_table	= intel_pch_thermal_id, | 
 | 	.probe		= intel_pch_thermal_probe, | 
 | 	.remove		= intel_pch_thermal_remove, | 
 | }; | 
 |  | 
 | module_pci_driver(intel_pch_thermal_driver); | 
 |  | 
 | MODULE_LICENSE("GPL v2"); | 
 | MODULE_DESCRIPTION("Intel PCH Thermal driver"); |