blob: a97b81d1d0da9b0b29fc622b34b6b54a06872ae8 [file] [log] [blame]
/*
* Copyright (C) 2007, 2011 Wolfgang Grandegger <wg@grandegger.com>
* Copyright (C) 2012 Stephane Grosjean <s.grosjean@peak-system.com>
*
* Derived from the PCAN project file driver/src/pcan_pci.c:
*
* Copyright (C) 2001-2006 PEAK System-Technik GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the version 2 of the GNU General Public License
* as published by the Free Software Foundation
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/netdevice.h>
#include <linux/delay.h>
#include <linux/pci.h>
#include <linux/io.h>
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>
#include <linux/can.h>
#include <linux/can/dev.h>
#include "sja1000.h"
MODULE_AUTHOR("Stephane Grosjean <s.grosjean@peak-system.com>");
MODULE_DESCRIPTION("Socket-CAN driver for PEAK PCAN PCI family cards");
MODULE_SUPPORTED_DEVICE("PEAK PCAN PCI/PCIe/PCIeC miniPCI CAN cards");
MODULE_SUPPORTED_DEVICE("PEAK PCAN miniPCIe/cPCI PC/104+ PCI/104e CAN Cards");
MODULE_LICENSE("GPL v2");
#define DRV_NAME "peak_pci"
struct peak_pciec_card;
struct peak_pci_chan {
void __iomem *cfg_base; /* Common for all channels */
struct net_device *prev_dev; /* Chain of network devices */
u16 icr_mask; /* Interrupt mask for fast ack */
struct peak_pciec_card *pciec_card; /* only for PCIeC LEDs */
};
#define PEAK_PCI_CAN_CLOCK (16000000 / 2)
#define PEAK_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
#define PEAK_PCI_OCR OCR_TX0_PUSHPULL
/*
* Important PITA registers
*/
#define PITA_ICR 0x00 /* Interrupt control register */
#define PITA_GPIOICR 0x18 /* GPIO interface control register */
#define PITA_MISC 0x1C /* Miscellaneous register */
#define PEAK_PCI_CFG_SIZE 0x1000 /* Size of the config PCI bar */
#define PEAK_PCI_CHAN_SIZE 0x0400 /* Size used by the channel */
#define PEAK_PCI_VENDOR_ID 0x001C /* The PCI device and vendor IDs */
#define PEAK_PCI_DEVICE_ID 0x0001 /* for PCI/PCIe slot cards */
#define PEAK_PCIEC_DEVICE_ID 0x0002 /* for ExpressCard slot cards */
#define PEAK_PCIE_DEVICE_ID 0x0003 /* for nextgen PCIe slot cards */
#define PEAK_CPCI_DEVICE_ID 0x0004 /* for nextgen cPCI slot cards */
#define PEAK_MPCI_DEVICE_ID 0x0005 /* for nextgen miniPCI slot cards */
#define PEAK_PC_104P_DEVICE_ID 0x0006 /* PCAN-PC/104+ cards */
#define PEAK_PCI_104E_DEVICE_ID 0x0007 /* PCAN-PCI/104 Express cards */
#define PEAK_MPCIE_DEVICE_ID 0x0008 /* The miniPCIe slot cards */
#define PEAK_PCIE_OEM_ID 0x0009 /* PCAN-PCI Express OEM */
#define PEAK_PCIEC34_DEVICE_ID 0x000A /* PCAN-PCI Express 34 (one channel) */
#define PEAK_PCI_CHAN_MAX 4
static const u16 peak_pci_icr_masks[PEAK_PCI_CHAN_MAX] = {
0x02, 0x01, 0x40, 0x80
};
static const struct pci_device_id peak_pci_tbl[] = {
{PEAK_PCI_VENDOR_ID, PEAK_PCI_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
{PEAK_PCI_VENDOR_ID, PEAK_PCIE_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
{PEAK_PCI_VENDOR_ID, PEAK_MPCI_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
{PEAK_PCI_VENDOR_ID, PEAK_MPCIE_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
{PEAK_PCI_VENDOR_ID, PEAK_PC_104P_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
{PEAK_PCI_VENDOR_ID, PEAK_PCI_104E_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
{PEAK_PCI_VENDOR_ID, PEAK_CPCI_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
{PEAK_PCI_VENDOR_ID, PEAK_PCIE_OEM_ID, PCI_ANY_ID, PCI_ANY_ID,},
#ifdef CONFIG_CAN_PEAK_PCIEC
{PEAK_PCI_VENDOR_ID, PEAK_PCIEC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
{PEAK_PCI_VENDOR_ID, PEAK_PCIEC34_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
#endif
{0,}
};
MODULE_DEVICE_TABLE(pci, peak_pci_tbl);
#ifdef CONFIG_CAN_PEAK_PCIEC
/*
* PCAN-ExpressCard needs I2C bit-banging configuration option.
*/
/* GPIOICR byte access offsets */
#define PITA_GPOUT 0x18 /* GPx output value */
#define PITA_GPIN 0x19 /* GPx input value */
#define PITA_GPOEN 0x1A /* configure GPx as ouput pin */
/* I2C GP bits */
#define PITA_GPIN_SCL 0x01 /* Serial Clock Line */
#define PITA_GPIN_SDA 0x04 /* Serial DAta line */
#define PCA9553_1_SLAVEADDR (0xC4 >> 1)
/* PCA9553 LS0 fields values */
enum {
PCA9553_LOW,
PCA9553_HIGHZ,
PCA9553_PWM0,
PCA9553_PWM1
};
/* LEDs control */
#define PCA9553_ON PCA9553_LOW
#define PCA9553_OFF PCA9553_HIGHZ
#define PCA9553_SLOW PCA9553_PWM0
#define PCA9553_FAST PCA9553_PWM1
#define PCA9553_LED(c) (1 << (c))
#define PCA9553_LED_STATE(s, c) ((s) << ((c) << 1))
#define PCA9553_LED_ON(c) PCA9553_LED_STATE(PCA9553_ON, c)
#define PCA9553_LED_OFF(c) PCA9553_LED_STATE(PCA9553_OFF, c)
#define PCA9553_LED_SLOW(c) PCA9553_LED_STATE(PCA9553_SLOW, c)
#define PCA9553_LED_FAST(c) PCA9553_LED_STATE(PCA9553_FAST, c)
#define PCA9553_LED_MASK(c) PCA9553_LED_STATE(0x03, c)
#define PCA9553_LED_OFF_ALL (PCA9553_LED_OFF(0) | PCA9553_LED_OFF(1))
#define PCA9553_LS0_INIT 0x40 /* initial value (!= from 0x00) */
struct peak_pciec_chan {
struct net_device *netdev;
unsigned long prev_rx_bytes;
unsigned long prev_tx_bytes;
};
struct peak_pciec_card {
void __iomem *cfg_base; /* Common for all channels */
void __iomem *reg_base; /* first channel base address */
u8 led_cache; /* leds state cache */
/* PCIExpressCard i2c data */
struct i2c_algo_bit_data i2c_bit;
struct i2c_adapter led_chip;
struct delayed_work led_work; /* led delayed work */
int chan_count;
struct peak_pciec_chan channel[PEAK_PCI_CHAN_MAX];
};
/* "normal" pci register write callback is overloaded for leds control */
static void peak_pci_write_reg(const struct sja1000_priv *priv,
int port, u8 val);
static inline void pita_set_scl_highz(struct peak_pciec_card *card)
{
u8 gp_outen = readb(card->cfg_base + PITA_GPOEN) & ~PITA_GPIN_SCL;
writeb(gp_outen, card->cfg_base + PITA_GPOEN);
}
static inline void pita_set_sda_highz(struct peak_pciec_card *card)
{
u8 gp_outen = readb(card->cfg_base + PITA_GPOEN) & ~PITA_GPIN_SDA;
writeb(gp_outen, card->cfg_base + PITA_GPOEN);
}
static void peak_pciec_init_pita_gpio(struct peak_pciec_card *card)
{
/* raise SCL & SDA GPIOs to high-Z */
pita_set_scl_highz(card);
pita_set_sda_highz(card);
}
static void pita_setsda(void *data, int state)
{
struct peak_pciec_card *card = (struct peak_pciec_card *)data;
u8 gp_out, gp_outen;
/* set output sda always to 0 */
gp_out = readb(card->cfg_base + PITA_GPOUT) & ~PITA_GPIN_SDA;
writeb(gp_out, card->cfg_base + PITA_GPOUT);
/* control output sda with GPOEN */
gp_outen = readb(card->cfg_base + PITA_GPOEN);
if (state)
gp_outen &= ~PITA_GPIN_SDA;
else
gp_outen |= PITA_GPIN_SDA;
writeb(gp_outen, card->cfg_base + PITA_GPOEN);
}
static void pita_setscl(void *data, int state)
{
struct peak_pciec_card *card = (struct peak_pciec_card *)data;
u8 gp_out, gp_outen;
/* set output scl always to 0 */
gp_out = readb(card->cfg_base + PITA_GPOUT) & ~PITA_GPIN_SCL;
writeb(gp_out, card->cfg_base + PITA_GPOUT);
/* control output scl with GPOEN */
gp_outen = readb(card->cfg_base + PITA_GPOEN);
if (state)
gp_outen &= ~PITA_GPIN_SCL;
else
gp_outen |= PITA_GPIN_SCL;
writeb(gp_outen, card->cfg_base + PITA_GPOEN);
}
static int pita_getsda(void *data)
{
struct peak_pciec_card *card = (struct peak_pciec_card *)data;
/* set tristate */
pita_set_sda_highz(card);
return (readb(card->cfg_base + PITA_GPIN) & PITA_GPIN_SDA) ? 1 : 0;
}
static int pita_getscl(void *data)
{
struct peak_pciec_card *card = (struct peak_pciec_card *)data;
/* set tristate */
pita_set_scl_highz(card);
return (readb(card->cfg_base + PITA_GPIN) & PITA_GPIN_SCL) ? 1 : 0;
}
/*
* write commands to the LED chip though the I2C-bus of the PCAN-PCIeC
*/
static int peak_pciec_write_pca9553(struct peak_pciec_card *card,
u8 offset, u8 data)
{
u8 buffer[2] = {
offset,
data
};
struct i2c_msg msg = {
.addr = PCA9553_1_SLAVEADDR,
.len = 2,
.buf = buffer,
};
int ret;
/* cache led mask */
if ((offset == 5) && (data == card->led_cache))
return 0;
ret = i2c_transfer(&card->led_chip, &msg, 1);
if (ret < 0)
return ret;
if (offset == 5)
card->led_cache = data;
return 0;
}
/*
* delayed work callback used to control the LEDs
*/
static void peak_pciec_led_work(struct work_struct *work)
{
struct peak_pciec_card *card =
container_of(work, struct peak_pciec_card, led_work.work);
struct net_device *netdev;
u8 new_led = card->led_cache;
int i, up_count = 0;
/* first check what is to do */
for (i = 0; i < card->chan_count; i++) {
/* default is: not configured */
new_led &= ~PCA9553_LED_MASK(i);
new_led |= PCA9553_LED_ON(i);
netdev = card->channel[i].netdev;
if (!netdev || !(netdev->flags & IFF_UP))
continue;
up_count++;
/* no activity (but configured) */
new_led &= ~PCA9553_LED_MASK(i);
new_led |= PCA9553_LED_SLOW(i);
/* if bytes counters changed, set fast blinking led */
if (netdev->stats.rx_bytes != card->channel[i].prev_rx_bytes) {
card->channel[i].prev_rx_bytes = netdev->stats.rx_bytes;
new_led &= ~PCA9553_LED_MASK(i);
new_led |= PCA9553_LED_FAST(i);
}
if (netdev->stats.tx_bytes != card->channel[i].prev_tx_bytes) {
card->channel[i].prev_tx_bytes = netdev->stats.tx_bytes;
new_led &= ~PCA9553_LED_MASK(i);
new_led |= PCA9553_LED_FAST(i);
}
}
/* check if LS0 settings changed, only update i2c if so */
peak_pciec_write_pca9553(card, 5, new_led);
/* restart timer (except if no more configured channels) */
if (up_count)
schedule_delayed_work(&card->led_work, HZ);
}
/*
* set LEDs blinking state
*/
static void peak_pciec_set_leds(struct peak_pciec_card *card, u8 led_mask, u8 s)
{
u8 new_led = card->led_cache;
int i;
/* first check what is to do */
for (i = 0; i < card->chan_count; i++)
if (led_mask & PCA9553_LED(i)) {
new_led &= ~PCA9553_LED_MASK(i);
new_led |= PCA9553_LED_STATE(s, i);
}
/* check if LS0 settings changed, only update i2c if so */
peak_pciec_write_pca9553(card, 5, new_led);
}
/*
* start one second delayed work to control LEDs
*/
static void peak_pciec_start_led_work(struct peak_pciec_card *card)
{
schedule_delayed_work(&card->led_work, HZ);
}
/*
* stop LEDs delayed work
*/
static void peak_pciec_stop_led_work(struct peak_pciec_card *card)
{
cancel_delayed_work_sync(&card->led_work);
}
/*
* initialize the PCA9553 4-bit I2C-bus LED chip
*/
static int peak_pciec_init_leds(struct peak_pciec_card *card)
{
int err;
/* prescaler for frequency 0: "SLOW" = 1 Hz = "44" */
err = peak_pciec_write_pca9553(card, 1, 44 / 1);
if (err)
return err;
/* duty cycle 0: 50% */
err = peak_pciec_write_pca9553(card, 2, 0x80);
if (err)
return err;
/* prescaler for frequency 1: "FAST" = 5 Hz */
err = peak_pciec_write_pca9553(card, 3, 44 / 5);
if (err)
return err;
/* duty cycle 1: 50% */
err = peak_pciec_write_pca9553(card, 4, 0x80);
if (err)
return err;
/* switch LEDs to initial state */
return peak_pciec_write_pca9553(card, 5, PCA9553_LS0_INIT);
}
/*
* restore LEDs state to off peak_pciec_leds_exit
*/
static void peak_pciec_leds_exit(struct peak_pciec_card *card)
{
/* switch LEDs to off */
peak_pciec_write_pca9553(card, 5, PCA9553_LED_OFF_ALL);
}
/*
* normal write sja1000 register method overloaded to catch when controller
* is started or stopped, to control leds
*/
static void peak_pciec_write_reg(const struct sja1000_priv *priv,
int port, u8 val)
{
struct peak_pci_chan *chan = priv->priv;
struct peak_pciec_card *card = chan->pciec_card;
int c = (priv->reg_base - card->reg_base) / PEAK_PCI_CHAN_SIZE;
/* sja1000 register changes control the leds state */
if (port == SJA1000_MOD)
switch (val) {
case MOD_RM:
/* Reset Mode: set led on */
peak_pciec_set_leds(card, PCA9553_LED(c), PCA9553_ON);
break;
case 0x00:
/* Normal Mode: led slow blinking and start led timer */
peak_pciec_set_leds(card, PCA9553_LED(c), PCA9553_SLOW);
peak_pciec_start_led_work(card);
break;
default:
break;
}
/* call base function */
peak_pci_write_reg(priv, port, val);
}
static struct i2c_algo_bit_data peak_pciec_i2c_bit_ops = {
.setsda = pita_setsda,
.setscl = pita_setscl,
.getsda = pita_getsda,
.getscl = pita_getscl,
.udelay = 10,
.timeout = HZ,
};
static int peak_pciec_probe(struct pci_dev *pdev, struct net_device *dev)
{
struct sja1000_priv *priv = netdev_priv(dev);
struct peak_pci_chan *chan = priv->priv;
struct peak_pciec_card *card;
int err;
/* copy i2c object address from 1st channel */
if (chan->prev_dev) {
struct sja1000_priv *prev_priv = netdev_priv(chan->prev_dev);
struct peak_pci_chan *prev_chan = prev_priv->priv;
card = prev_chan->pciec_card;
if (!card)
return -ENODEV;
/* channel is the first one: do the init part */
} else {
/* create the bit banging I2C adapter structure */
card = kzalloc(sizeof(struct peak_pciec_card), GFP_KERNEL);
if (!card)
return -ENOMEM;
card->cfg_base = chan->cfg_base;
card->reg_base = priv->reg_base;
card->led_chip.owner = THIS_MODULE;
card->led_chip.dev.parent = &pdev->dev;
card->led_chip.algo_data = &card->i2c_bit;
strncpy(card->led_chip.name, "peak_i2c",
sizeof(card->led_chip.name));
card->i2c_bit = peak_pciec_i2c_bit_ops;
card->i2c_bit.udelay = 10;
card->i2c_bit.timeout = HZ;
card->i2c_bit.data = card;
peak_pciec_init_pita_gpio(card);
err = i2c_bit_add_bus(&card->led_chip);
if (err) {
dev_err(&pdev->dev, "i2c init failed\n");
goto pciec_init_err_1;
}
err = peak_pciec_init_leds(card);
if (err) {
dev_err(&pdev->dev, "leds hardware init failed\n");
goto pciec_init_err_2;
}
INIT_DELAYED_WORK(&card->led_work, peak_pciec_led_work);
/* PCAN-ExpressCard needs its own callback for leds */
priv->write_reg = peak_pciec_write_reg;
}
chan->pciec_card = card;
card->channel[card->chan_count++].netdev = dev;
return 0;
pciec_init_err_2:
i2c_del_adapter(&card->led_chip);
pciec_init_err_1:
peak_pciec_init_pita_gpio(card);
kfree(card);
return err;
}
static void peak_pciec_remove(struct peak_pciec_card *card)
{
peak_pciec_stop_led_work(card);
peak_pciec_leds_exit(card);
i2c_del_adapter(&card->led_chip);
peak_pciec_init_pita_gpio(card);
kfree(card);
}
#else /* CONFIG_CAN_PEAK_PCIEC */
/*
* Placebo functions when PCAN-ExpressCard support is not selected
*/
static inline int peak_pciec_probe(struct pci_dev *pdev, struct net_device *dev)
{
return -ENODEV;
}
static inline void peak_pciec_remove(struct peak_pciec_card *card)
{
}
#endif /* CONFIG_CAN_PEAK_PCIEC */
static u8 peak_pci_read_reg(const struct sja1000_priv *priv, int port)
{
return readb(priv->reg_base + (port << 2));
}
static void peak_pci_write_reg(const struct sja1000_priv *priv,
int port, u8 val)
{
writeb(val, priv->reg_base + (port << 2));
}
static void peak_pci_post_irq(const struct sja1000_priv *priv)
{
struct peak_pci_chan *chan = priv->priv;
u16 icr;
/* Select and clear in PITA stored interrupt */
icr = readw(chan->cfg_base + PITA_ICR);
if (icr & chan->icr_mask)
writew(chan->icr_mask, chan->cfg_base + PITA_ICR);
}
static int peak_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
struct sja1000_priv *priv;
struct peak_pci_chan *chan;
struct net_device *dev, *prev_dev;
void __iomem *cfg_base, *reg_base;
u16 sub_sys_id, icr;
int i, err, channels;
err = pci_enable_device(pdev);
if (err)
return err;
err = pci_request_regions(pdev, DRV_NAME);
if (err)
goto failure_disable_pci;
err = pci_read_config_word(pdev, 0x2e, &sub_sys_id);
if (err)
goto failure_release_regions;
dev_dbg(&pdev->dev, "probing device %04x:%04x:%04x\n",
pdev->vendor, pdev->device, sub_sys_id);
err = pci_write_config_word(pdev, 0x44, 0);
if (err)
goto failure_release_regions;
if (sub_sys_id >= 12)
channels = 4;
else if (sub_sys_id >= 10)
channels = 3;
else if (sub_sys_id >= 4)
channels = 2;
else
channels = 1;
cfg_base = pci_iomap(pdev, 0, PEAK_PCI_CFG_SIZE);
if (!cfg_base) {
dev_err(&pdev->dev, "failed to map PCI resource #0\n");
err = -ENOMEM;
goto failure_release_regions;
}
reg_base = pci_iomap(pdev, 1, PEAK_PCI_CHAN_SIZE * channels);
if (!reg_base) {
dev_err(&pdev->dev, "failed to map PCI resource #1\n");
err = -ENOMEM;
goto failure_unmap_cfg_base;
}
/* Set GPIO control register */
writew(0x0005, cfg_base + PITA_GPIOICR + 2);
/* Enable all channels of this card */
writeb(0x00, cfg_base + PITA_GPIOICR);
/* Toggle reset */
writeb(0x05, cfg_base + PITA_MISC + 3);
usleep_range(5000, 6000);
/* Leave parport mux mode */
writeb(0x04, cfg_base + PITA_MISC + 3);
icr = readw(cfg_base + PITA_ICR + 2);
for (i = 0; i < channels; i++) {
dev = alloc_sja1000dev(sizeof(struct peak_pci_chan));
if (!dev) {
err = -ENOMEM;
goto failure_remove_channels;
}
priv = netdev_priv(dev);
chan = priv->priv;
chan->cfg_base = cfg_base;
priv->reg_base = reg_base + i * PEAK_PCI_CHAN_SIZE;
priv->read_reg = peak_pci_read_reg;
priv->write_reg = peak_pci_write_reg;
priv->post_irq = peak_pci_post_irq;
priv->can.clock.freq = PEAK_PCI_CAN_CLOCK;
priv->ocr = PEAK_PCI_OCR;
priv->cdr = PEAK_PCI_CDR;
/* Neither a slave nor a single device distributes the clock */
if (channels == 1 || i > 0)
priv->cdr |= CDR_CLK_OFF;
/* Setup interrupt handling */
priv->irq_flags = IRQF_SHARED;
dev->irq = pdev->irq;
chan->icr_mask = peak_pci_icr_masks[i];
icr |= chan->icr_mask;
SET_NETDEV_DEV(dev, &pdev->dev);
dev->dev_id = i;
/* Create chain of SJA1000 devices */
chan->prev_dev = pci_get_drvdata(pdev);
pci_set_drvdata(pdev, dev);
/*
* PCAN-ExpressCard needs some additional i2c init.
* This must be done *before* register_sja1000dev() but
* *after* devices linkage
*/
if (pdev->device == PEAK_PCIEC_DEVICE_ID ||
pdev->device == PEAK_PCIEC34_DEVICE_ID) {
err = peak_pciec_probe(pdev, dev);
if (err) {
dev_err(&pdev->dev,
"failed to probe device (err %d)\n",
err);
goto failure_free_dev;
}
}
err = register_sja1000dev(dev);
if (err) {
dev_err(&pdev->dev, "failed to register device\n");
goto failure_free_dev;
}
dev_info(&pdev->dev,
"%s at reg_base=0x%p cfg_base=0x%p irq=%d\n",
dev->name, priv->reg_base, chan->cfg_base, dev->irq);
}
/* Enable interrupts */
writew(icr, cfg_base + PITA_ICR + 2);
return 0;
failure_free_dev:
pci_set_drvdata(pdev, chan->prev_dev);
free_sja1000dev(dev);
failure_remove_channels:
/* Disable interrupts */
writew(0x0, cfg_base + PITA_ICR + 2);
chan = NULL;
for (dev = pci_get_drvdata(pdev); dev; dev = prev_dev) {
priv = netdev_priv(dev);
chan = priv->priv;
prev_dev = chan->prev_dev;
unregister_sja1000dev(dev);
free_sja1000dev(dev);
}
/* free any PCIeC resources too */
if (chan && chan->pciec_card)
peak_pciec_remove(chan->pciec_card);
pci_iounmap(pdev, reg_base);
failure_unmap_cfg_base:
pci_iounmap(pdev, cfg_base);
failure_release_regions:
pci_release_regions(pdev);
failure_disable_pci:
pci_disable_device(pdev);
/* pci_xxx_config_word() return positive PCIBIOS_xxx error codes while
* the probe() function must return a negative errno in case of failure
* (err is unchanged if negative) */
return pcibios_err_to_errno(err);
}
static void peak_pci_remove(struct pci_dev *pdev)
{
struct net_device *dev = pci_get_drvdata(pdev); /* Last device */
struct sja1000_priv *priv = netdev_priv(dev);
struct peak_pci_chan *chan = priv->priv;
void __iomem *cfg_base = chan->cfg_base;
void __iomem *reg_base = priv->reg_base;
/* Disable interrupts */
writew(0x0, cfg_base + PITA_ICR + 2);
/* Loop over all registered devices */
while (1) {
struct net_device *prev_dev = chan->prev_dev;
dev_info(&pdev->dev, "removing device %s\n", dev->name);
unregister_sja1000dev(dev);
free_sja1000dev(dev);
dev = prev_dev;
if (!dev) {
/* do that only for first channel */
if (chan->pciec_card)
peak_pciec_remove(chan->pciec_card);
break;
}
priv = netdev_priv(dev);
chan = priv->priv;
}
pci_iounmap(pdev, reg_base);
pci_iounmap(pdev, cfg_base);
pci_release_regions(pdev);
pci_disable_device(pdev);
}
static struct pci_driver peak_pci_driver = {
.name = DRV_NAME,
.id_table = peak_pci_tbl,
.probe = peak_pci_probe,
.remove = peak_pci_remove,
};
module_pci_driver(peak_pci_driver);